Ribbon Cable connector Compliant with MIL Standard HIF3B Series ■Features 1. Product Compliant with MIL Standard HIF3B series has been developed as a product compliant with MIL standard, and used for wide applications. 2. UL Approval Product HIF3B series connectors are UL approved. 3. Mechanism to Prevent Mis-insertion This connector is equipped with the mechanism to prevent Misinsertion as follows. 1 The system provides the convex area to insert the guide-key on the pin header side, and to guide it in combination with the socket convex area (MIL standard). 2 The system embeds and guides the polarizing key in the socket holes. 4. Applicable Cable AWG#28 The applicable cable is UL2651 AWG#28 flat cable (7 cores./ 0.127mm, jacket dia. 0.9±0.1mm). ■Product Specifications Current rating : 1A Rating Operating Temperature Range : –55 to +85ç (Note 1) Storage Temperature Range : –10 to +60ç (Note 2) Storage Humidity Range : 40 to 70% (Note 2) Voltage rating : 200V AC Operating Moisture Range : 40 to 80% Item Specification Condition 1. Insulation Resistance 1000M ohms min. 500V DC 2. Withstanding voltage No flashover or insulation breakdown. 650V AC/1 minute 3. Contact Resistance 15m ohms max. 0.1A 4. Vibration No electrical discontinuity of 1µs or more Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions. 5. Humidity (Steady state) Insulation resistance: 1000M ohms min. 6. Temperature Cycle 96 hours at temperature of 40ç and humidity of 90% to 95% (-55ç: 30 minutes ➝ 15 to 35ç: 5 minutes max. No damage, cracks, or parts looseness. 125ç: 30 minutes ➝ 15 to 35ç: 5 minutes max.) 5 cycles 7. Durability (Mating/un-mating) Contact resistance: 15m ohms max. 500 cycles Solder bath: 260ç for 10 seconds 8. Resistance to Soldering heat No deformation of components affecting performance. Manual soldering: 360ç for 5 seconds Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation. Note 3: Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a specific part number shown. Note 4: Please note that there is a risk of deforming the lock when an excessive load is applied to the inside. ■Material Part Material Finish Remarks Insulator PBT Black UL94V-0 Socket Contact Beryllium copper Pin header contact Brass Connection area Gold plated Selective Gold plated ––––––– ––––––– B15 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Ordering Information ●Socket HIF 3B - * D - 2.54 R q w e r t y q Series Name : HIF w Series No. : 3B, 3BA, 3BB (50, 60, 64 contacts only) e Number of contacts : 6,10,14,16, 20, 26, 30, 34, 40, 50, 60, 64 r Contact alignment : D : Double t Contact pitch : 2.54mm y Connection type R : ID type ●Pin Header HIF 3B - * P A - 2.54 DS q w e q Series Name : HIF w Series No. : r t y u : (14 contacts not included) 3BC: (10 contacts only) 3BA, 3BB: (50, 60, 64 contacts only) 3BD: (10 contacts only) 3B e Number of contacts : 6,10,14,16, 20, 26, 30, 34, 40, 50, 60, 64 r P : Pin header t A : Selective gold plated y Contact pitch : 2.54mm u Contact style B16 DS : Right angle type DSA : Straight type HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Socket (With guide to prevent mis-insertion) Body Protector Clamp Note1, Note2: The number of polarizing keys and polarizing keyways changes according to products. Refer to the list as shown below. Note3: The 50, 60 and 64 contact connector contain two types of polarizing guides. Use the products, referring to Notes 1 and 2. Note4: The 6 contact has no polarizing mark. Unit:mm Part Number CL No. Number of Contacts A B C D Polarizing Guide (Note 1) HIF3BA- 6D-2.54R 610-0032-3 6 12.19 5.08 6.35 7.72 HIF3BA-10D-2.54R 610-0021-7 10 17.27 10.16 11.43 12.8 ★ HIF3BA-14D-2.54R 610-0022-0 14 22.35 15.24 16.51 17.88 ★ HIF3BA-16D-2.54R 610-0023-2 16 24.89 17.78 19.05 20.42 ★ HIF3BA-20D-2.54R 610-0024-5 20 29.97 22.86 24.13 25.5 ★ HIF3BA-26D-2.54R 610-0025-8 26 37.59 30.48 31.75 33.12 ★ HIF3BA-30D-2.54R 610-0026-0 30 42.67 35.56 36.83 38.2 ★ HIF3BA-34D-2.54R 610-0027-3 34 47.75 40.64 41.91 43.28 ★ HIF3BA-40D-2.54R 610-0028-6 40 55.37 48.26 49.53 50.9 ★ HIF3BA-50D-2.54R 610-0029-9 50 68.07 60.96 62.23 63.6 One on right and left sides, resp. ★ HIF3BB-50D-2.54R 610-0041-4 50 68.07 60.96 62.23 63.6 ★ HIF3BA-60D-2.54R 610-0030-8 60 80.77 73.66 74.93 76.3 One on right and left sides, resp. ★ HIF3BB-60D-2.54R 610-0042-7 60 80.77 73.66 74.93 76.3 ★ HIF3BA-64D-2.54R 610-0031-0 64 85.85 78.74 80.01 81.38 One on right and left sides, resp. ★ HIF3BB-64D-2.54R 610-0043-0 64 85.85 78.74 80.01 81.38 Polarizing Keyway (Note 2) RoHS None One on left side One at center YES One on right and left sides, resp. One at center One at center One at center The products marked with ★ comply with MIL standard. B17 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Socket Body Protector Clamp Note1: The number of polarizing keys and polarizing keyways changes according to products. For details, refer to the list as shown below. Note2: The 6 contact has no polarizing mark. Unit:mm Part Number CL No. Number of Contacts A B C D HIF3B- 6D-2.54R 610-0012-6 6 12.19 5.08 6.35 7.72 ★ HIF3B-10D-2.54R 610-0001-0 10 17.27 10.16 11.43 12.80 ★ HIF3B-14D-2.54R 610-0002-2 14 22.35 15.24 16.51 17.88 ★ HIF3B-16D-2.54R 610-0003-5 16 24.89 17.78 19.05 20.42 ★ HIF3B-20D-2.54R 610-0004-8 20 29.97 22.86 24.13 25.50 ★ HIF3B-26D-2.54R 610-0005-0 26 37.59 30.48 31.75 33.12 ★ HIF3B-30D-2.54R 610-0006-3 30 42.67 35.56 36.83 38.2 ★ HIF3B-34D-2.54R 610-0007-6 34 47.75 40.64 41.91 43.28 ★ HIF3B-40D-2.54R 610-0008-9 40 55.37 48.26 49.53 50.90 ★ HIF3B-50D-2.54R 610-0009-1 50 68.07 60.96 62.23 63.6 ★ HIF3B-60D-2.54R 610-0010-0 60 80.77 73.66 74.93 76.3 ★ HIF3B-64D-2.54R 610-0011-3 64 85.85 78.74 80.01 81.38 Polarizing Guide (Note 1) RoHS None One on left side YES One on right and left sides, resp. The products marked with ★ comply with MIL standard. B18 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Four Wall Angle Through hole BPCB mounting pattern Note 1, Note 2: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note 3: The spacer moves to the right according to the number of contacts. Note 4: The 10, 50, 60 and 64 contact connectors contain two types of polarizing slots. Use products, referring to (Note 1) (Note 2). ■n=number of contacts Unit:mm Part Number CL No. Number of Contacts A B C ★ HIF3BA-10PA-2.54DS(71) 610-0091-2(71) 10 32.0 17.5 10.16 HIF3BD-10PA-2.54DS(71) 610-0171-0(71) 10 32.0 17.5 10.16 ★ HIF3BA-14PA-2.54DS(71) 610-0092-5(71) 14 37.1 22.6 15.24 ★ HIF3BA-16PA-2.54DS(71) 610-0093-8(71) 16 39.6 25.1 17.78 ★ HIF3BA-20PA-2.54DS(71) 610-0094-0(71) 20 44.7 30.2 22.86 ★ HIF3BA-26PA-2.54DS(71) 610-0095-3(71) 26 52.3 37.8 30.48 ★ HIF3BA-30PA-2.54DS(71) 610-0096-6(71) 30 57.4 42.9 35.56 ★ HIF3BA-34PA-2.54DS(71) 610-0097-9(71) 34 62.5 48.0 40.64 ★ HIF3BA-40PA-2.54DS(71) 610-0098-1(71) 40 70.1 55.6 48.26 ★ HIF3BA-50PA-2.54DS(71) 610-0099-4(71) 50 82.8 68.3 60.96 ★ HIF3BB-50PA-2.54DS(71) 610-0131-5(71) 50 82.8 68.3 60.96 ★ HIF3BA-60PA-2.54DS(71) 610-0100-1(71) 60 95.5 81.0 73.66 ★ HIF3BB-60PA-2.54DS(71) 610-0132-8(71) 60 95.5 81.0 73.66 ★ HIF3BA-64PA-2.54DS(71) 610-0101-4(71) 64 100.6 86.1 78.74 ★ HIF3BB-64PA-2.54DS(71) 610-0133-0(71) 64 100.6 86.1 78.74 D 28.14 MAX51.1 28.14 MAX51.1 33.24 MAX56.2 35.74 MAX58.7 40.84 MAX63.8 48.44 MAX71.4 53.54 MAX76.5 58.64 MAX81.6 66.24 MAX89.2 78.94 MAX101.9 78.94 MAX101.9 91.64 MAX114.6 91.64 MAX114.6 96.74 MAX119.7 96.74 MAX119.7 E F 21.8 27.9 Polarizing Slot (Note 1) None Polarizing Key Install RoHS (Note 2) One on right side 21.8 27.9 None 26.9 33.0 One on right side 29.5 35.5 34.5 40.6 42.2 48.3 One at center 47.2 53.3 YES 52.3 58.4 59.9 66.0 72.6 78.7 One on right and left sides, resp. 72.6 78.7 One on right and left sides, resp. One at center 85.3 91.4 One on right and left sides, resp. 85.3 91.4 One at center 90.4 96.5 One on right and left sides, resp. 90.4 96.5 One at center The products marked with ★ comply with MIL standard. B19 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Four-Wall Straight Through hole BPCB mounting pattern Note 1, Note 2: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note 3: The spacer moves to the right according to the number of contacts. Note 4: The 10, 50, 60 and 64 contact connectors contain two types of polarizing slots. Use products, confirming (Note 1) (Note 2). Note 5: The 6 contact has no polarity mark. ■n=number of contacts Unit:mm Part Number CL No. Number of Contacts 562-0503-9-71 6 26.92 12.42 05.08 HIF3BA-10PA-2.54DSA(71) 610-0111-8-71 10 32.0 17.5 10.16 ★ HIF3BD-10PA-2.54DSA(71) 610-0181-3-71 ★ HIF3BA-14PA-2.54DSA(71) 610-0112-0-71 10 32.0 17.5 10.16 14 37.1 22.6 15.24 ★ HIF3BA-16PA-2.54DSA(71) 610-0113-3-71 ★ HIF3BA-20PA-2.54DSA(71) 610-0114-6-71 16 39.6 25.1 17.78 20 44.7 30.2 22.86 ★ HIF3BA-26PA-2.54DSA(71) 610-0115-9-71 ★ HIF3BA-30PA-2.54DSA(71) 610-0116-1-71 26 52.3 37.8 30.48 30 57.4 42.9 35.56 ★ HIF3BA-34PA-2.54DSA(71) 610-0117-4-71 ★ HIF3BA-40PA-2.54DSA(71) 610-0118-7-71 34 62.5 48.0 40.64 40 70.1 55.6 48.26 ★ HIF3BA-50PA-2.54DSA(71) 610-0119-0-71 ★ HIF3BB-50PA-2.54DSA(71) 610-0141-9-71 50 82.8 68.3 60.96 50 82.8 68.3 60.96 ★ HIF3BA-60PA-2.54DSA(71) 610-0120-9-71 ★ HIF3BB-60PA-2.54DSA(71) 610-0142-1-71 60 95.5 81.0 73.66 ★ HIF3-6PA-2.54DSA(71) ★ HIF3BA-64PA-2.54DSA(71) 610-0121-1-71 ★ HIF3BB-64PA-2.54DSA(71) 610-0143-4-71 A B C 60 95.5 81.0 73.66 64 100.6 86.1 78.74 64 100.6 86.1 78.74 D 23.06 MAX46.02 28.14 MAX51.1 28.14 MAX51.1 33.24 MAX56.2 35.74 MAX58.7 40.84 MAX63.8 48.44 MAX71.4 53.54 MAX76.5 58.64 MAX81.6 66.24 MAX89.2 78.94 MAX101.9 78.94 MAX101.9 91.64 MAX114.6 91.64 MAX114.6 96.74 MAX119.7 96.74 MAX119.7 E F Polarizing Slot (Note 1) Polarizing Key Install RoHS (Note 2) 16.7 22.82 One at center None 21.8 27.9 None One on right side 21.8 27.9 None 26.9 33.0 One on right side 29.5 35.5 34.5 40.6 42.2 48.3 One at center 47.2 53.3 YES 52.3 58.4 59.9 66.0 72.6 78.7 One on right and left sides, resp. 72.6 78.7 One on right and left sides, resp. One at center 85.3 91.4 One on right and left sides, resp. 85.3 91.4 One at center 90.4 96.5 One on right and left sides, resp. 90.4 96.5 One at center The products marked with ★ comply with MIL standard. B20 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Three Wall Angle Type BPCB mounting pattern Note 1, Note 2: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note 3: The spacer moves according to the number of contacts. Note 4: The 10 contact connector consists of two types. Use products, confirming (Note 1) (Note 2). ■n=number of contacts Unit:mm Part Number CL No. Number of Contacts A B C ★ HIF3BD-10PA-2.54DS(71) 610-0051-8-71 10 32.0 17.5 10.16 HIF3BC-10PA-2.54DS(71) 610-0151-2-71 10 32.0 17.5 10.16 ★ HIF3BD-16PA-2.54DS(71) 610-0052-0-71 16 39.6 25.1 17.78 ★ HIF3BD-20PA-2.54DS(71) 610-0053-3-71 20 44.7 30.2 22.86 ★ HIF3BD-26PA-2.54DS(71) 610-0054-6-71 26 52.3 37.8 30.48 ★ HIF3BD-30PA-2.54DS(71) 610-0055-9-71 30 57.4 42.9 35.56 ★ HIF3BD-34PA-2.54DS(71) 610-0056-1-71 34 62.5 48.0 40.64 ★ HIF3BD-40PA-2.54DS(71) 610-0057-4-71 40 70.1 55.6 48.26 ★ HIF3BD-50PA-2.54DS(71) 610-0058-7-71 50 82.8 68.3 60.96 ★ HIF3BD-60PA-2.54DS(71) 610-0059-0-71 60 95.5 81.0 73.66 ★ HIF3BD-64PA-2.54DS(71) 610-0060-9-71 64 100.6 86.1 78.74 D 28.14 MAX51.1 28.14 MAX51.1 35.74 MAX58.7 40.84 MAX63.8 48.44 MAX71.4 53.54 MAX76.5 58.64 MAX81.6 66.24 MAX89.2 78.94 MAX101.9 91.64 MAX114.6 96.74 MAX119.7 E F 21.8 27.9 Polarizing Slot (Note 1) Polarizing Key Install (Note 2) None One on right side 21.8 27.9 RoHS None 29.5 35.5 34.5 40.6 42.2 48.3 One at center 47.2 53.3 52.3 58.4 One on right and left sides, resp. YES 59.9 66.0 72.6 78.7 85.3 91.4 One on right and left sides, resp. 90.4 96.5 The products marked with ★ comply with MIL standard. B21 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Three Wall Straight Through hole BPCB mounting pattern Note1,Note2: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note3: The spacer moves to the right according to the number of contacts. Note4: The 10 contact connector consists of two types. Use products, referring to (Note 1) and (Note 2). ■n=number of contacts Unit:mm Part Number CL No. Number of Contacts A B C ★ HIF3BD-10PA-2.54DSA(71) 610-0071-5-71 10 32.0 17.5 10.16 HIF3BC-10PA-2.54DSA(71) 610-0161-6-71 10 32.0 17.5 10.16 ★ HIF3BD-16PA-2.54DSA(71) 610-0072-8-71 16 39.6 25.1 17.78 ★ HIF3BD-20PA-2.54DSA(71) 610-0073-0-71 20 44.7 30.2 22.86 ★ HIF3BD-26PA-2.54DSA(71) 610-0074-3-71 26 52.3 37.8 30.48 ★ HIF3BD-30PA-2.54DSA(71) 610-0075-6-71 30 57.4 42.9 35.56 ★ HIF3BD-34PA-2.54DSA(71) 610-0076-9-71 34 62.5 48.0 40.64 ★ HIF3BD-40PA-2.54DSA(71) 610-0077-1-71 40 70.1 55.6 48.26 ★ HIF3BD-50PA-2.54DSA(71) 610-0078-4-71 50 82.8 68.3 60.96 ★ HIF3BD-60PA-2.54DSA(71) 610-0079-7-71 60 95.5 81.0 73.66 ★ HIF3BD-64PA-2.54DSA(71) 610-0080-6-71 64 100.6 86.1 78.74 D 28.14 MAX51.1 28.14 MAX51.1 35.74 MAX58.7 40.84 MAX63.8 48.44 MAX71.4 53.54 MAX76.5 58.64 MAX81.6 66.24 MAX89.2 78.94 MAX101.9 91.64 MAX114.6 96.74 MAX119.7 E F 21.8 27.9 Polarizing Slot (Note 1) None 21.8 27.9 Polarizing Key Install RoHS (Note 2) One on right side None 29.5 35.5 34.5 40.6 42.2 48.3 One at center 47.2 53.3 52.3 58.4 YES One on right and left sides, resp. 59.9 66.0 72.6 78.7 85.3 91.4 One on right and left sides, resp. 90.4 96.5 The products marked with ★ comply with MIL standard. B22 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Four Wall Wrapping Type BPCB mounting pattern Note 1, Note 2. The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note 3. The spacer moves to the right according to the number of contacts. Note 4. The 10, 50, 60 and 64 contact connectors consists of two types. Use products, confirming (Note 1) (Note 2). Note 5. The mark * indicates the number of contacts. Note 6. The nut built-in specification product is also provided. The product can be fixed by M2 screws from the rear side. Use the screw of (board thickness) +4 mm under the neck. ■n=number of contacts Unit:mm Part Number CL No. Number of Contacts A B C ★ HIF3BA-10P-2.54W 610-0503-8 10 32.0 17.5 10.16 HIF3BD-10P-2.54W 610-0492-3 10 32.0 17.5 10.16 ★ HIF3BA-14P-2.54W 610-0493-6 14 37.1 22.6 15.24 ★ HIF3BA-16P-2.54W 610-0494-9 16 39.6 25.1 17.78 ★ HIF3BA-20P-2.54W 610-0495-1 20 44.7 30.2 22.86 ★ HIF3BA-26P-2.54W 610-0496-4 26 52.3 37.8 30.48 ★ HIF3BA-30P-2.54W 610-0497-7 30 57.4 42.9 35.56 ★ HIF3BA-34P-2.54W 610-0498-0 34 62.5 48.0 40.64 ★ HIF3BA-40P-2.54W 610-0499-2 40 70.1 55.6 48.26 ★ HIF3BA-50P-2.54W 610-0504-0 50 82.8 68.3 60.96 ★ HIF3BB-50P-2.54W 610-0500-0 50 82.8 68.3 60.96 ★ HIF3BA-60P-2.54W 610-0505-3 60 95.5 81.0 73.66 ★ HIF3BB-60P-2.54W 610-0501-2 60 95.5 81.0 73.66 ★ HIF3BA-64P-2.54W 610-0506-6 64 100.6 86.1 78.74 ★ HIF3BB-64P-2.54W 610-0502-5 64 100.6 86.1 78.74 D 28.14 MAX51.1 28.14 MAX51.1 33.24 MAX56.2 35.74 MAX58.7 40.84 MAX63.8 48.44 MAX71.4 53.54 MAX76.5 58.64 MAX81.6 66.24 MAX89.2 78.94 MAX101.9 78.94 MAX101.9 91.64 MAX114.6 91.64 MAX114.6 96.74 MAX119.7 96.74 MAX119.7 E F 21.8 27.9 Polarizing Slot (Note 1) Polarizing Key Install (Note 2) None One on right side 21.8 27.9 None 26.9 33.0 One on right side RoHS 29.5 35.5 34.5 40.6 42.2 48.3 One at center 47.2 53.3 YES 52.3 58.4 59.9 66.0 72.6 78.7 One on right and left sides, resp. 72.6 78.7 One on right and left sides, resp. One at center 85.3 91.4 One on right and left sides, resp. 85.3 91.4 One at center 90.4 96.5 One on right and left sides, resp. 90.4 96.5 One at center The products marked with ★ comply with MIL standard. B23 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Four Wall Straight Through hole [Flux Blister Prevention Type] BPCB mounting pattern Note1: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. ■n=number of contacts Unit:mm Part Number CL No. Number of Contacts A B C ★ HIF3CA-10PA-2.54DSA(71) 610-0701-1-71 10 32.0 17.5 10.16 HIF3CD-10PA-2.54DSA(71) 610-0722-1-71 10 32.0 17.5 10.16 ★ HIF3CA-16PA-2.54DSA(71) 610-0703-7-71 16 39.6 25.1 17.78 ★ HIF3CA-20PA-2.54DSA(71) 610-0704-0-71 20 44.7 30.2 22.86 ★ HIF3CA-26PA-2.54DSA(71) 610-0705-2-71 26 52.3 37.8 30.48 ★ HIF3CA-30PA-2.54DSA(71) 610-0706-5-71 30 57.4 42.9 35.56 ★ HIF3CA-34PA-2.54DSA(71) 610-0707-8-71 34 62.5 48.0 40.64 ★ HIF3CA-40PA-2.54DSA(71) 610-0708-0-71 40 70.1 55.6 48.26 ★ HIF3CA-50PA-2.54DSA(71) 610-0709-3-71 50 82.8 68.3 60.96 ★ HIF3CB-50PA-2.54DSA(71) 610-0721-9-71 50 82.8 68.3 60.96 ★ HIF3CB-60PA-2.54DSA(71) 610-0723-4-71 60 95.5 81.0 73.66 ★ HIF3CB-64PA-2.54DSA(71) 610-0724-7-71 64 100.6 86.1 78.74 D 28.14 MAX51.1 28.14 MAX51.1 35.74 MAX58.7 40.84 MAX63.8 48.44 MAX71.4 53.54 MAX76.5 58.64 MAX81.6 66.24 MAX89.2 78.94 MAX101.9 78.94 MAX101.9 91.64 MAX114.6 96.74 MAX119.7 E F 21.8 27.9 Polarizing Slot None 21.8 27.9 Polarizing Key Install RoHS One on right side None 29.5 35.5 34.5 40.6 42.2 48.3 One at center 47.2 53.3 YES 52.3 58.4 One on right and left sides, resp. 59.9 66.0 72.6 78.7 One on right and left sides, resp. 72.6 78.7 85.3 91.4 One at center 90.4 96.5 The products marked with ★ comply with MIL standard. B24 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Two Stage Staking Right Angle Through hole Note 1, Note 2: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note 3: The spacer moves to the right according to the number of contacts. Note 4: The 10, 50, 60 and 64 contact connectors consists of two types. Use products, confirming (Note 1) (Note 2). Note 5: The mark * ndicates the number of contacts. Note 6: The locator is located optionally. Unit:mm Part Number CL No. Number of Contacts A B C ★ HIF3BA-10PA-2.54WB(71) 610-1502-0-71 10 32.0 17.5 10.16 HIF3BD-10PA-2.54WB(71) 610-1503-3-71 10 32.0 17.5 10.16 ★ HIF3BA-16PA-2.54WB(71) 610-1505-9-71 16 39.6 25.1 17.78 ★ HIF3BA-20PA-2.54WB(71) 610-1506-1-71 20 44.7 30.2 22.86 ★ HIF3BA-26PA-2.54WB(71) 610-1507-4-71 26 52.3 37.8 30.48 ★ HIF3BA-30PA-2.54WB(71) 610-1508-7-71 30 57.4 42.9 35.56 ★ HIF3BA-34PA-2.54WB(71) 610-1509-0-71 34 62.5 48.0 40.64 ★ HIF3BA-40PA-2.54WB(71) 610-1510-9-71 40 70.1 55.6 48.26 ★ HIF3BA-50PA-2.54WB(71) 610-1511-1-71 50 82.8 68.3 60.96 ★ HIF3BB-50PA-2.54WB(71) 610-1512-4-71 50 82.8 68.3 60.96 ★ HIF3BA-60PA-2.54WB(71) 610-1513-7-71 60 95.5 81.0 73.66 ★ HIF3BB-60PA-2.54WB(71) 610-1514-0-71 60 95.5 81.0 73.66 ★ HIF3BA-64PA-2.54WB(71) 610-1515-2-71 64 100.6 86.1 78.74 ★ HIF3BB-64PA-2.54WB(71) 610-1516-5-71 64 100.6 86.1 78.74 D 28.14 MAX51.1 28.14 MAX51.1 35.74 MAX58.7 40.84 MAX63.8 48.44 MAX71.4 53.54 MAX76.5 58.64 MAX81.6 66.24 MAX89.2 78.94 MAX101.9 78.94 MAX101.9 91.64 MAX114.6 91.64 MAX114.6 96.74 MAX119.7 96.74 MAX119.7 E F 21.8 27.9 Polarizing Slot (Note 1) None 21.8 27.9 Polarizing Key Install RoHS (Note 2) One on right side None 29.5 35.5 34.5 40.6 42.2 48.3 One at center 47.2 53.3 52.3 58.4 YES 59.9 66.0 72.6 78.7 One on right and left sides, resp. 72.6 78.7 One on right and left sides, resp. One at center 85.3 91.4 One on right and left sides, resp. 85.3 91.4 One at center 90.4 96.5 One on right and left sides, resp. 90.4 96.5 One at center The products marked with ★ comply with MIL standard. B25 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard BCombination Pattern Note : Fix the HIF3-mounting hole spacer by screws between upper stage and lower stage connectors. BPCB mounting pattern ■Mounting Hole Spacer Part Number CL No. HIF-3 mounting hole spacer 562-0714-4 Note : 2 pieces are contained in a bag. B26 Finish PBT Black RoHS YES HIF3B Series●Ribbon Cable connector Compliant with MIL Standard BPolarizing Key HIF3B-GK CL562-0601-8 HIF3-GPIN(A) HIF3BA-GPIN Note1: One unit of this product is a set of five pieces in conjunction with a runner. The unit for sale is defined one pack containing 20 pieces. Note2: This product is applicable to HIF3A*D2.54R, HIF3C*D2.54C and HIF3BA-*D2.54C products. Part Number CL No. Material Remarks Note1: One unit of this product is a set of five pieces in conjunction with a runner. The unit for sale is defined one pack containing 20 pieces. Note2: This product is applicable to the HIF3BA-*D2.54R product. RoHS HIF3-GPIN(A) 562-0126-6 Poly acetal (white) A set of 5 pieces YES Part Number CL No. Material Remarks RoHS HIF3BA-GPIN 612-0500-2 Poly acetal (white) A set of 5 pieces YES B27 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard BHIF3-Multi Clamp BHIF3-*CL Pull Tab This clamp is used for intermediate connection in the This pull tab is used for the HIF3 series equipped with cable clamp bus-line system, etc. Remove compulsory force from the function. Remove all compulsory force, which is loaded on the insulation displacement area of the connector in insulation displacement area of the connector for extraction. intermediate connection. Note: This HIF3-* Pull Tab can not be used for HIF3BA-*PD. Note: The pin header corresponds to the HIF3BAE Note: The pin header corresponds to the HIF3BAE series (lock E). series (lock E). BLock Lock G Lock F Part Number : HIF3BAG-**PA-2.54DSA(71) Part Number : HIF3BAG-**PA-2.54DSA(71) ●Low profile type, and used for lock ejection. Connector height is reduced. Since no connector clamp is needed on the cable side, this is used without turning back on the cable side. Take care about this point. B28 27.3 ●F Type Lock Pin Header 21.5 ●Low Profile Lock Pin Header ●Locking range more reduced than conventional lock type. Even if connectors are aligned laterally, the mounting space is reduced. Note : The clamp must be replaced for HIF3A socket type 60 contacts only. Take care about this point. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Socket for Crimping Unit: mm Part Number CL No. Number of Contacts A B HIF3BA-10D-2.54C 610-1041-0 10 17.25 10.16 HIF3BA-14D-2.54C 610-1051-3 14 22.35 15.24 HIF3BA-16D-2.54C 610-1042-2 16 24.8 17.78 HIF3BA-20D-2.54C 610-1043-5 20 29.95 22.86 HIF3BA-26D-2.54C 610-1044-8 26 37.55 30.48 HIF3BA-30D-2.54C 610-1045-0 30 42.63 35.56 HIF3BA-34D-2.54C 610-1046-3 34 47.75 40.64 HIF3BA-40D-2.54C 610-1047-6 40 55.35 48.26 HIF3BA-50D-2.54C 610-1048-9 HIF3BB-50D-2.54C 610-1061-7 50 68.04 60.96 HIF3BA-60D-2.54C 610-1049-1 HIF3BB-60D-2.54C 610-1062-0 HIF3BA-64D-2.54C 610-1064-5 HIF3BB-64D-2.54C 610-1063-2 60 80.77 73.66 64 85.85 78.74 Polarizing Guide RoHS One at center YES One right and left side, resp. One at center One right and left side, resp. One at center One right and left side, resp. One at center Note: Some variations may differ from those in above figures. B29 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Cover Case for Crimping socket Unit: mm Part Number CL No. Number of Contacts A B C D E HIF3-20CV(72) 562-0201-0-72 20 24.5 18.0 12.0 30.5 29.95 HIF3-26CV(72) 562-0202-2-72 26 30.2 20.0 14.0 32.0 37.55 HIF3-30CV(72) 562-0203-5-72 30 32.2 22.0 16.0 33.0 42.63 HIF3-34CV(72) 562-0204-8-72 34 34.2 24.0 18.0 33.5 47.75 HIF3-40CV(72) 562-0205-0-72 40 36.2 26.0 20.0 35.5 55.35 HIF3-50CV(72) 562-0206-3-72 50 39.2 29.0 23.0 38.0 68.04 HIF3-60CV(72) 562-0207-6-72 60 42.2 32.0 26.0 40.5 80.77 Note 1: The type F lock pin header cannot be used for a mating member. Note 2: Note that the product cannot be used with AWG #20. Applicable jacket diameters are as described below. 20 contacts: 1.7 mm diameter MAX 26 to 40 contacts: 1.6 mm diameter MAX 50 to 60 contacts: 1.4 mm diameter MAX B30 RoHS YES HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Contact for Crimping Socket HIF3-2226SC HIF3-2226SCA Applicable cable Manual crimping tool RoHS 562-0079-8 gold plated contact in bag YES 562-0244-2 Selective gold plated contact in bag AWG#22 to #26 UL 1007 Stranded wire HIF3-T2226HC HIF3-2428SC HIF3-2428SCA Applicable cable Manual crimping tool RoHS 562-0124-0 gold plated contact in bag YES 562-0246-8 Selective gold plated contact in bag AWG#24 to #28 UL 1007 Stranded wire HIF3-TA2428HC RoHS HIF3-2022SC 562-0492-4 gold plated contact in bag YES Applicable cable AWG#20 to #22 UL 1007 Stranded wire Manual crimping tool HIF3-TA2022HC RoHS RoHS RoHS HIF3-2226SCF 562-0080-7 gold plated contact in reel HIF3-2428SCF 562-0125-3 gold plated contact in reel HIF3-2022SCF 562-0493-7 gold plated contact in reel YES YES YES * HIF3-2226SCFA 562-0245-5 Selective gold plated contact in reel * HIF3-2428SCFA 562-0247-0 Selective gold plated contact in reel Applicable cable AWG#20 to #22 UL 1007 Stranded wire Applicable cable AWG#22 to #26 UL 1007 Stranded wire Applicable cable AWG#24 to #28 UL 1007 Stranded wire Note:* products have both side careers. Type VA (Selective gold plated in reel) Applicable Cable Part Number CL No. HIF3-2226SCFC 613-0002-1 AWG#22 to #26 UL 1007 Stranded wire HIF3-2630SCFC 613-0001-9 AWG#26 to #30 UL 1007 Stranded wire HIF3A-3236SCFC 613-0005-0 AWG#32 to #36 UL 1007 Stranded wire A 11.5 11.5 12.4 B 0.8 0.8 1.7 C 1.8 1.4 1.1 D 1.8 1.35 1.1 E 2.3 2.0 1.4 F RoHS 2.6 2.1 YES 1.5 Type VA (Selective gold plated contact in bag) Applicable Cable Manual Crimp Tool A B C D E F RoHS Part Number CL No. HIF3-2226SCC 613-0004-7 AWG#22 to #26 UL 1007 Stranded wire HIF3-TB2226HC 11.5 0.8 1.8 1.8 2.3 2.6 YES HIF3-2630SCC 613-0003-4 AWG#26 to #30 UL 1007 Stranded wire HIF3-TB2630HC 11.5 0.8 1.4 1.35 2.0 2.1 B31 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard BTools ●Crimping Tool Manual Crimping Tool Part Number CL No. HIF3-T2226HC 550-0063-8 Part Number CL No. CM-105 901-0005-4 HIF3-T2226HC ●Automatic Crimping Tool (Type: CM-105) ●Contact Extraction Tools Part Number CL No. HIF1-PO 550-0049-7 How to use the extraction tool (1) How to extract contacts (2) How to adjust the lance (raise) As shown in Figure 1, where the extraction tool is inserted in the lance fixed slot on the insulated case, slightly pull the cable, and the contact can be removed. In order to re-insert the contact removed from the insulated case, raise the contact lance area using the tool A, and re-insert the contact, as shown in Figure 2. Figure 1 B32 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard Type Item Manual Manual crimping tool Automatic Part Number CL No. Applicable Cable 550-0063-8 HIF3-TA2428HC 550-0100-2 HIF3-TA2022HC 550-0124-0 HIF3-2022SC AWG#20 to #22 HIF3-TB2226HC 550-0154-1 HIF3-2226SCC AWG#22 to #26 HIF3-TB2630HC 550-0155-4 HIF3-2630SCC AWG#26 to #30 901-0005-4 ––––––– HIF3-2226SCF HIF3-2428SCF HIF3-2226SCFA HIF3-2428SCFA ––––––– AWG#22 to #26 AWG#24 to #28 AWG#22 to #26 AWG#24 to #28 AP105-HIF3-22-28SCF 901-4031-6 (Note1) AP105-HIF3-22-28SCFA 901-4030-3 (Note1) Extraction tool HIF3-2226SC HIF3-2226SCA HIF3-2428SC HIF3-2428SCA HIF3-T2226HC Automatic crimping tool unit CM-105 Applicator Applicable Contact AWG#22 to #26 AWG#24 to #28 AP105-HIF3-2022S 901-4027-9 HIF3-2022SCF AWG#20 to #22 AP105-HIF3-2226SCFC 901-4005-6 HIF3-2226SCFC AWG#22 to #26 AP105-HIF3-2630SCFC 901-4006-9 HIF3-2630SCFC AWG#26 to #30 AP105-HIF3-3236SCFC 901-4007-1 HIF3-3236SCFC AWG#32 to #36 HIF1-PO 550-0049-7 ––––––– ––––––– Note1: AP106-HIF3-22-28SCF and AP105-HIF3-22-28CFA can be modified by changing a few parts. B33 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard BSocket Side (Crimping) Assembling Procedures (1) As shown in Figure 1, peel the applicable cable (AWG#20 to #26) jacket, and connect it using crimping jig HIF3-TA2022HC, HIF3-TA2226HC, or HIF3-TA2426HC. In this case, insert the cable so as to hit the contact cable stripper position as shown Figure 2. (2) After connection as shown Figure 2, check the contact direction, and insert the contact as shown Figures 3 and 4. Slightly pull the cable, and check whether the contact lance position is firmly fixed to the insulation case, as shown in the area (A). Note1 : For handling procedures for special crimping tools, refer to the "Handling Instruction Manual". Note2 : Wire strip length: Refer to crimp condition sheet. Wire strip length B34 Figure 1 Figure 2 Figure 3 Figure 4 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard HIF3B Connection Circuit Diagram Type AB Type AB Type AD Type AD Type CD Type CD B35 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard Type AC Type AC Type CC Type CC Type AA Type AA B36 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard HIF2E R(S) A to HIF3B Connection Circuit Diagram Type AA Type AC B37 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard Type BA Type BC B38 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard HIF2E R(S)B to HIF3 Connection Circuit Diagram Type AA Type AC B39 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard Type BA Type BC B40 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard HIF3B In-line Type Ribbon Cable Connector ■Features 1. In-line Type This connector can be used for internal wiring cable to cable within equipment. 2. Compatibility This connector is compatible with HIF3A series as well as HIF3B series socket. 3. Applicable Cable The applicable cable is UL2651 AWG#28 flat cable (7 pcs./6.127mm, jacket diameter: 0.8 to 1.0mm). ■Product Specifications Operating Temperature Range : –55 to +85ç (Note 1) Storage Temperature Range : –10 to +60ç (Note 2) Current rating : 1A Rating Storage Humidity Range : 40 to 70% (Note 2) Voltage rating : 200V AC Operating Moisture Range : 40 to 80% Item Specification Condition 1. Insulation Resistance 1000M ohms min. 500V DC 2. Withstanding voltage No flashover or insulation breakdown. 650V AC/1 minute 3. Contact Resistance 15m ohms max. 0.1A 4. Vibration No electrical discontinuity of 1µs or more Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions. 5. Humidity (Steady state) Insulation resistance: 1000M ohms min. 6. Temperature Cycle 96 hours at temperature of 40ç and humidity of 90% to 95% (-65ç: 30 minutes ➝ 15 to 35ç: 5 minutes max. No damage, cracks, or parts looseness. 125ç: 30 minutes ➝ 15 to 35ç: 5 minutes max.) 5 cycles 7. Durability (Mating/un-mating) Contact resistance: 15m ohms max. 500 cycles Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation. Note 3: Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a specific part number shown. ■Material Part Material Finish Remarks Insulator PBT Black UL94V-0 Plug Contact Beryllium copper Gold plated over nickel underplated –––––– ■Ordering Information HIF3BA - * P D - 2.54 R - MC q q Series Name w e r t y u : HIF3BB (50, 60, 64 contacts only) e P : Plug HIF3BD (10 contacts only) r D : contact alignment : D : Double HIF3BAE (60 contacts only) t Contact Pitch w Number of Contacts : 10, 16, 20, 26, 30, 34, 40, 50, 60 and 64 : 2.54mm y Connection type : Ribbon cable u MC : Mold clamp B41 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Plug Note 1, Note 2: The number of polarizing slot and key installed positions changes according to products. The 10 contact connector only has no position for polarizing key insulation. Note 3: The number indicated in parentheses are sizes for 60 and 64 contact connectors. Note 4: The HIF3BAE-60PD-2.54R-MC product partially differs in a locking form, and the mating member is applicable for HIF3A only. Unit:mm Part Number CL No. Number of Contacts A B C HIF3BDE-10PD-2.54R-MC 611-0031-7 10 31.98 17.48 10.16 HIF3BAE-16PD-2.54R-MC 611-0032-0 16 39.60 25.10 17.78 HIF3BAE-20PD-2.54R-MC 611-0033-2 20 44.68 30.18 22.86 HIF3BAE-26PD-2.54R-MC 611-0034-5 26 52.30 37.80 30.48 HIF3BAE-30PD-2.54R-MC 611-0035-8 30 57.38 42.88 35.56 HIF3BAE-34PD-2.54R-MC 611-0036-0 34 62.46 47.96 40.64 HIF3BAE-40PD-2.54R-MC 611-0037-3 40 70.08 55.58 48.26 HIF3BAE-50PD-2.54R-MC 611-0038-6 50 HIF3BBE-50PD-2.54R-MC 611-0041-0 50 HIF3BAE-60PD-2.54R-MC 611-0039-9 60 HIF3BBE-60PD-2.54R-MC 611-0042-3 60 D 28.14 MAX51.1 35.74 MAX58.7 40.84 MAX63.8 48.44 MAX71.4 53.54 MAX76.5 58.64 MAX81.6 66.24 MAX89.2 E F G H 29.50 37.75 34.58 42.83 42.20 50.45 One at center 33.2 47.28 55.53 52.36 60.61 29.2 59.98 68.23 One on right and left sides, resp. 72.68 80.93 91.64 MAX114.6 HIF3BAE-60PD-2.54R-MC 611-0059-6 60 91.7 MAX121.3 HIF3BAE-64PD-2.54R-MC 611-0040-8 64 96.74 HIF3BBE-64PD-2.54R-MC 611-0045-1 64 85.38 93.63 35.2 MAX119.7 One on right and left sides, resp. One at center 31.2 37.2 One on right and left sides, resp. 90.46 98.71 29.2 35.2 100.56 86.06 78.74 One at center *D size B42 YES One at center MAX101.9 95.48 80.98 73.66 RoHS 21.88 30.13 78.94 82.78 68.28 60.96 Polarizing slot locking size unlocking size HIF3B Series●Ribbon Cable connector Compliant with MIL Standard BConnection Procedures Note1: Cable length tolerance Less than 500 +10 +00 (mm) More than 500 +3 +0 (mm) Note2: When a cable such as a twist cable or a slit (like a roller screen) cable is used, the cable pitch will change according to cable manufacturers. If connection failure has occurred, please contact Hirose sales. Type AO Type BO Type CO Type DO B43