AC-DC 175-300 Watts xppower.com HUL Series • Compact Size, Low Profile • Up to 5.85 W/in3 Power Density • Single & Multiple Outputs • Convection-cooled Ratings • Remote On/Off • Power Fail Detect • 12 V Fan Supply Specification Input General Input Voltage Input Frequency Input Current • 90-132 VAC, 180-264 VAC (auto-ranging) • 47-63 Hz • HUL175: 4.4 A max at 115 VAC, 2.2 A max at 230 VAC HUL200: 5.0 A max at 115 VAC, 2.5 A max at 230 VAC HUL300: 6.3 A max at 115 VAC, 3.15 A max at 230 VAC Inrush Current • 35 A at 115 VAC, 70 A max at 264 VAC +25 °C cold start Power Factor • Passive PFC, meets EN6100-3-2, -3 Earth Leakage Current • <1.5 mA at 230 VAC / 50 Hz Output • See tables • ±5% on output 1 • ±1% max for single/main output ±5% for auxiliary outputs Minimum Load • See tables & note 1 for 175 W model Start Up Delay • 1 s max Start Up Rise Time • 20 ms max Hold Up Time • >15 ms at 115 VAC Total Regulation • ±1% max for single output models, ±5% max for multiple output models Over/Undershoot • <5% max Transient Response • 5% max deviation, recovery to within 1% in 500 µs for a 50% load change Ripple & Noise • 1% pk-pk (50 mV max for 3.3 V output) Overvoltage Protection • 130% on output 1 only, recycle input to reset Overtemperature • Shuts down when ambient temperature Protection exceeds +85 °C, auto recovery Overload Protection • 110-135% of total power, auto recovery Short Circuit Protection • Trip and restart (Hiccup mode) Temperature • ±0.1%/°C Coefficient Remote Sense • HUL175 only. Compensates for 0.5 V drop on 3.3 V output Fan Output Switching Frequency Power Density Power Fail Detect MTBF • 80% typical • 3000 VAC Input to Output, 1500 VAC Input to Ground, 500 VAC Output to Ground • 42 kHz typical • HUL175: 4.51 W/In3, HUL200: 5.85 W/In3, HUL300: 4.41 W/In3 • On = Logic high 100-500 ms after outputs with regulation Fail = Logic low at least 1 ms prior to loss of output • 100 kHrs per MIL-HDBK-217F Environmental Output Voltage Output Voltage Trim Initial Set Accuracy Remote On/Off Efficiency Isolation • On = Logic High or Open Off = Logic Low or Short Not available on HUL175 • 12 V, 300 mA Operating Temperature • 0 °C to +60 °C, derate linearly from 100% at +40 °C to 50% at +60 °C Cooling • See notes Operating Humidity • 5-90% RH, non-condensing Storage Temperature • -20 °C to +85 °C Operating Altitude • 3000 m Shock • 15 g (non-operation), 11 ms (half sine wave), 3 times for each axis Vibration • 10-55 Hz (non-operation) 2 g, sweep time 3 mins, 60 mins/axis EMC & Safety Emissions Harmonic Currents Voltage Flicker ESD Immunity Radiated Immunity EFT/Burst Surge Conducted Immunity Dips & Interruptions Safety Approvals • EN55022 and FCC, level B (level A - 300 W) conducted • EN61000-3-2 • EN61000-3-3 • EN61000-4-2, level 4 Perf Criteria A • EN61000-4-3, level 3 Perf Criteria A • EN61000-4-4, level 3 Perf Criteria A • EN61000-4-5, level 3 Perf Criteria A • EN61000-4-6, 10 V Perf Criteria A • EN61000-4-11, 30% 10 ms, 70% 100 ms, 95% 5000 ms, Perf Criteria A, B, B • EN60950, UL60950, CSA22.2 No. 950 per cUL, CE Mark Voltage Nom 5.0 V 5.0 V 5.0 V 5.0 V Output 1 Conv Max Voltage Cooled 18.7 CFM Nom 10.0 A 15.0 A 3.3 V 10.0 A 15.0 A 3.3 V 10.0 A 15.0 A 3.3 V 10.0 A 15.0 A 3.3 V Output 2 Conv Max Voltage Cooled 18.7 CFM Nom 10.0 A 20.0 A 12.0 V 10.0 A 20.0 A 12.0 V 10.0 A 20.0 A 24.0 V 10.0 A 20.0 A 15.0 V Output 3 Conv Max Cooled 18.7 CFM 2.2 A 3.0 A 2.2 A 3.0 A 1.5 A 2.0 A 2.2 A 3.0 A Voltage Nom -5.0 V -12.0 V -12.0 V -15.0 V Output 4 Conv Max Cooled 18.7 CFM 0.7 A 1.0 A 0.7 A 1.0 A 0.7 A 1.0 A 0.7 A 1.0 A Model Number HUL175-40-3† HUL175-42-3† HUL175-45-3† HUL175-46-3† Notes 1. 2. 3. 4. 5. Minimum load is 2.0 A for V1, 0.0 A for V2 & V4, and 0.3 A for V3. Total regulation for V1, V2 and V3 = ±5%; V4 = ±3%. Total regulation includes tolerance, line regulation and load regulation. Total combined output power for the 3.3 V and 5.0 V not to exceed 126 W with 18.7 CFM or 70 W with convection cooling. Maximum load continuous output power is 175 W with minimum 18.7 CFM forced air cooling or 100 W with convection cooling. Outputs are fully isolated. † Available from Farnell. See pages 204-206. Mechanical Details All dimensions are in inches (mm). Tolerance: 0.02 (0.5) max. Weight: 1.32 lbs (600 g) approx. 0.65 (16.5) 0.2 (5.1) B M3 x 0.5 STAND OFF 4 PLACES A 2 P2 1 M4 x 0.7 NUT FASTENER 8 PLACES 24 3.80 (96.5) P1 G N L P3 2.50 (63.5) 1 A B Pin 1 2 P2 Connector Function Fan + Fan - Pin 1 2, 14 3, 15 4, 16 5, 17 6, 18 7, 19 8, 20 9, 21 10, 22 11,23 12 13 24 P3 Connector Function +3.3 V Sense+ Output 2 Output 2 Return Return Return Output 1 Output 1 Output 3 Return Output 4 Power Fail Detect +3.3 V SenseReturn 6.40 (162.5) 4.58 (116.3) 0.80 (20.3) 1.50 (38.1) 0.24 (6.00) 2.90 (73.7) A A 1.25 (31.8) 5.20 (132.1) 6.00 (152.4) 6.80 (172.7) Notes 1. 2. 3. 4. Input connector P1 mates with Molex housing 09-91-0500 and Molex 2478/2578/8818 series crimp terminal. Output connector P3 mates with Molex housing 39-01-2240 and Molex 44476 series crimp terminal. Fan connector P2 mates with JST housing XHP-2 and JST SXH-002T-P0.6 crimp terminals. Fan output is 12 V/160 mA. Covered versions are available, add suffix: ‘-C’ to model number for cover only, dimensions: 3.80” x 6.80” x 1.66” (96.5 x 172.7 x 42.1 mm), add suffix: ‘-FC’ to model number for fan cover, dimensions: 3.80” x 6.80” x 2.48” (96.5 x 172.7 x 63.0 mm). 5. Cable harnesses with 11.81” (300 mm) wire available, order part HUL175 LOOM KIT†. For mating connectors only, order part HUL175 CONN KIT†. 6. Covers are available separately. Order part HUL175 COVER† or HUL175 F/COVER† for Fan Cover. 7. Max penetration of screws 0.12” (3.0 mm). AC-DC HUL175 Models and Ratings AC-DC HUL200 Models and Ratings Output 1 Current Voltage Nom Min Max 3.3 V 0.5 A 30.0 A 5.0 V 0.5 A 40.0 A 12.0 V 0.5 A 16.7 A 15.0 V 0.5 A 13.3 A 24.0 V 0.5 A 8.3 A 48.0 V 0.5 A 4.1 A +5.0 V 0.5 A 20.0 A +5.0 V 0.5 A 20.0 A +5.0 V 0.5 A 20.0 A +5.0 V 0.5 A 20.0 A +5.0 V 0.5 A 20.0 A +5.0 V 0.5 A 20.0 A +5.0 V 0.5 A 20.0 A +5.0 V 0.5 A 20.0 A +12.0 V 0.5 A 3.0 A +5.0 V 0.5 A 5.0 A +5.0 V 0.5 A 3.0 A +5.0 V 0.5 A 5.0 A Output 2 Current Voltage Nom Min Max +12.0 +15.0 +24.0 +12.0 +15.0 +12.0 +24.0 +15.0 +36.0 +36.0 +24.0 +12.0 V V V V V V V V V V V V 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 A A A A A A A A A A A A 8.0 6.6 4.2 8.0 5.0 6.0 3.0 5.0 5.0 2.5 8.0 2.5 Output 3 Current Voltage nom Min Max A A A A A A A A A A A A -5.0 -12.0 -5.0 +5.0 +12.0 +12.0 +24.0 V V V V V V V 0.0 0.0 0.0 0.0 0.0 0.0 0.0 A A A A A A A 1.0 1.0 1.0 3.0 1.0 0.1 2.5 A A A A A A A Output 4(3) Current Voltage nom Min Max F 12.0 F 15.0 F 12.0 F 12.0 F 15.0 -12.0 -12.0 -12.0 -12.0 V V V V V V V V V 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 A A A A A A A A A 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.1 1.0 A A A A A A A A A Model Number(1) HUL200-10-1† HUL200-10† HUL200-12† HUL200-13† HUL200-14† HUL200-18† HUL200-23† HUL200-24† HUL200-25† HUL200-31† HUL200-32† HUL200-40† HUL200-45† HUL200-46† HUL200-47 HUL200-47-2 HUL200-47-3 HUL200-47-1 Notes 1. Use part number UL200-XX for product without harmonic correction. e.g.: UL200-10. 2. Total output power for HUL200-10-1 is 73 W convection-cooled, 100 W with 18.7 CFM forced air cooling. 3. Output 4 is floating except for -47 models. It can be connected externally for positive or negative output. 4. Total output power for HUL200 single output models is 150 W convection-cooled, 200 W with 18.7 CFM forced air cooling. 5. Total output power for HUL200 multi output models is 100 W convection-cooled, 200 W with 18.7 CFM forced air cooling. 6. Tolerance 5% all outputs, except single output units - tolerance 2%. † Available from Farnell. See pages 204-206. Mechanical Details All dimensions are in inches (mm). Tolerance: 0.02 (0.5) max. Weight: 1.76 lbs (800 g) approx. 1.25 (31.8) Mounting holes: A: M4 x 0.7, 8 places B: 6-32, 8 places 2.5 (63.5) L N G A B A 1 P1 B B A 6.40 (162.5) 5.77 (146.7) 6.80 (172.7) A FAN B P2 B A A 1.27 (32.3) 1.50 (38.1) Pin 1 B P3 3.80 (96.5) ±0.3 (7.6) Pin 1 Pin 1 2 3 4 5 6 7 8 9 10 11 12 P2 Connector Single Output Multi Output Output 1 Output 3 Output 1 Return Output 1 Return Output 1 Return Output 1 Return Output 1 Output 1 Return Output 1 Return Output 1 Return Output 1 Return Output 2 Return Output 4 Return Output 4 Return Pin 1 2 3 4 5 6 P3 Connector Single Output Multi Output Multi-outputs have 3 Fan + separate 2 pin Return connectors for Fan, Return Power Good and Remote Power Fail Detect ON/OFF. These are (7) Remote On/Off clearly marked on the PCB. Return - Notes 1. 2. 3. 4. 5. Input connector P1 mates with Molex housing 09-91-0500 and Molex 2478/2578/8818 series crimp terminal. Output connector P2 mates with Molex housing 09-91-1200 and Molex 2478/2578/8818 series crimp terminal. Fan connector mates with JST housing XHP-2 and JST SXH-002T-P0.6 crimp terminals. Signals connector P3 mates with JST housing XHP-6 and JST SXH-002T-P0.6 crimp terminals or 3 off JST housing XHP-2 and JST SXH-002T-P0.6 crimp terminals. Covered versions are available: add suffix: ‘-C’ to model number for cover only - dimensions: 3.80” x 6.80” x 1.66” (96.5 x 172.7 x 42.1 mm), add suffix: ‘-FC’ to model number for fan cover - dimensions: 3.80” x 6.80” x 2.48” (96.5 x 172.7 x 63.0 mm). 6. Covers are available separately. Order part HUL200 COVER† or HUL200 F/COVER† for Fan Cover. 7. Output is turned off by taking the Remote On/Off pin low (connect to Return). 8. Cable harnesses with 11.81” (300 mm) wire available, order part number HUL200 LOOM-S for single output models, HUL200 LOOM-D for dual output models, HUL200 LOOM-T for triple output models or HUL200 LOOM-Q for quad output models. 9. For mating connectors only, order part HUL200 CON KT†. 10. Max penetration of screws 0.12” (3.0 mm) Output 1 Current Voltage Nom Min Max 3.3 V 0.5 A 60.00 A 5.0 V 0.5 A 60.00 A 12.0 V 0.5 A 25.00 A 15.0 V 0.5 A 20.00 A 24.0 V 0.5 A 12.50 A 48.0 V 0.5 A 6.25 A +5.0 V 0.5 A 30.00 A +5.0 V 0.5 A 30.00 A +5.0 V 0.5 A 30.00 A +5.0 V 0.5 A 30.00 A +5.0 V 0.5 A 30.00 A +5.0 V 0.5 A 30.00 A +5.0 V 0.5 A 30.00 A +5.0 V 0.5 A 30.00 A Output 2 Current Voltage Nom Min Max +12.0 +15.0 +24.0 +12.0 +15.0 +12.0 +24.0 +15.0 V V V V V V V V 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 A A A A A A A A 12.5 10.0 6.3 10.5 8.0 10.0 4.3 7.4 Output 3 Current Voltage nom Min Max A A A A A A A A -5.0 V -12.0 V -5.0 V 0.0 A 0.0 A 0.0 A 2.0 A 2.0 A 2.0 A Output 4(2) Current Voltage nom Min Max F F F F F 12.0 15.0 12.0 12.0 15.0 V V V V V 0.0 0.0 0.0 0.0 0.0 A A A A A 2.0 2.0 2.0 2.0 2.0 A A A A A Model Number(1) HUL300-10-1† HUL300-10† HUL300-12† HUL300-13† HUL300-14† HUL300-18† HUL300-23† HUL300-24† HUL300-25† HUL300-31† HUL300-32† HUL300-40† HUL300-45† HUL300-46† Notes 1. Use part number UL300-XX for product without harmonic correction. e.g. UL300-10. 2. Output 4 is floating. It can be connected externally for positive or negative output. 3. Total output power for HUL300-12,13,14,18 models is 200 W convection-cooled, 300 W with 30 CFM forced air cooling. 4. Total output power for all other HUL300 models is 150 W convection-cooled, 300 W with 30 CFM forced air cooling. 5. Tolerance 5% all outputs, except single output units - tolerance 2%. † Available from Farnell. See pages 204-206. Mechanical Details All dimensions are in inches (mm). Tolerance: 0.02 (0.5) max. Weight: 2.20 lbs (1.0 kg) approx. 0.25 (6.35) 2.50 (63.5) 0.50 (12.7) P1 1.09 (27.8) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 L N G M4 x 0.7 NUT FASTENER (12 PLACES) 8.00 (203.2) 7.50 (190.5) 7.00 (177.8) 5.81 (147.6) P2 1 1.00 (25.4) 0.25 (6.4) PIN 1 14 FAN 4.25 (108.0) P3 Pin 1 2 3 4 5 6 P2 Connector Single Output Multi Output Output 1 Output 3 Output 1 Output 1 Output 1 Output 1 Output 1 Output 1 Output 1 Output 1 Output 1 Return Output 1 Return Return Return Return Return Return Return Return Output 2 Return Output 2 Return Output 4 Return Output 4 Return P3 Connector Single Output Multi Output Fan + Return Return DC OK(7) DC OK Return Power Fail Detect Remote On/Off(6) Remote On/Off(6) Return Return Power Fail Detect 2.00 (50.8) Notes 1. 2. 3. 4. 5. Input connector P1 mates with Molex housing 09-91-0500 and Molex 2478/2578/8818 series crimp terminal. Output connector P2 mates with Molex housing 09-91-1400 and Molex 2478/2578/8818 series crimp terminal. Fan connector mates with JST housing XHP-2 and JST SXH-002T-P0.6 crimp terminals. Multiple outputs only. Signals connector P3 mates with JST housing XHP-6 and JST SXH-002T-P0.6 crimp terminals. Covered versions are available, add suffix: ‘-C’ to model number for cover only, dimensions: 4.25” x 8.00” x 2.16” (108.0 x 203.2 x 54.8 mm) add suffix: ‘-FC’ to model number for fan cover, dimensions: 4.25” x 8.00” x 3.00” (108.0 x 203.2 x 75.7 mm). 6. Output is turned off by taking the Remote On/Off pin low (connect to Return). 7. DC OK is a open collector output. Low = normal operation. 8. Cable harnesses with 11.81” (300 mm) wire available, order part number HUL300 LOOM-S for single output models, HUL300 LOOM-D for dual output models, HUL300 LOOM-T for triple output models or HUL300 LOOM-Q for quad output models. For mating connectors only, order part HUL300 CON KT†. 9. Covers are available separately. Order part HUL300 COVER† or HUL300 F/COVER† for Fan Cover. 10. Max penetration of screws 0.12” (3.0 mm). 17-Apr-07 AC-DC HUL300 Models and Ratings