PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF BOE HYDIS AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE HYDIS AND MUST BE RETURNED TO BOE HYDIS UPON ITS REQUEST TITLE : HX121WX1-100 Preliminary Product Specification Rev. P2 FOR MORE INFORMATION: AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA, 92656 Http://www.AZDISPLAYS.com BOE HYDIS TECHNOLOGY SPEC. NUMBER B2005-C001-A (1/3) PRODUCT GROUP TFT LCD REV. P2 ISSUE DATE 2008. 01. 14 PAGE 1 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 DATE PREPARED REVISION HISTORY REV. ECN NO. DESCRIPTION OF CHANGES P0 Initial Release ‘07. 08. 08 H. R. Park P1 -.Add the surface treatment_AR(4page) -.Add the life time test condition (8page) -.Add the color reproduction(9page) -.Change the reflectance(9page) ’07. 08. 10 H. R. Park P2 -.Change the Power Consumption, CR, Gamut, Chromaticity, Reflectance ’08. 01. 14 H. R. Park SPEC. NUMBER SPEC TITLE B2005-C001-A (2/3) HX121WX1-100 Pre-Product Specification PAGE 2 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 Contents No Item Page 1.0 General Description 4 2.0 Absolute Maximum Ratings 6 3.0 Electrical Specifications 7 4.0 Optical Specifications 9 5.0 Interface Connections 14 6.0 Signal Timing Specifications 17 7.0 Signal Timing Waveforms 17 8.0 Input Signals, Basic Display Colors & Gray Scale of Colors 19 9.0 Power Sequence 20 10.0 Mechanical Characteristics 21 11.0 Mechanical Drawing 22 12.0 Reliability Test 25 13.0 Handling & Cautions 25 14.0 Labels 27 15.0 Packing Information 28 SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 3 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 1.0 GENERAL DESCRIPTION 1.1 Introduction HX121WX1-100 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 12.1 inch diagonally measured active area with WXGA resolutions (1280 horizontal by 800 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical Stripe and this module can display 262,144 colors. The TFT-LCD panel used for this module is a low reflection and higher color type. Source Driver LVDS Input Signal LVDS Rx + T/CON Gate Driver 1 (CN Connector DC/DC Gamma Vcom VDD TFT LCD Panel BACK LIGHT (Fluorescent Lamp) 1280 ×800 1 ) HVDD VDIM LED Driver Back Light (SMD LED Array) CN2 1.2 Features z Thin and Light Weight z 3.3 V Logic Power Supply z 12V Back-light Power Supply z 1 Channel LVDS Interface z SMD LED (48EA) Array (Bottom Side/Horizontal Direction) z 262,144 Colors z Data Enable Signal Mode z Side Mounting Frame z Green Product (RoHS) z Anti-Reflection polarizer product for sunlight readability SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 4 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 1.3 Application z Tablet PC (Wide type) 1.4 General Specifications Parameter Specification Active area 261.12(H) ×163.20(V) Number of pixels 1280(H) ×800(V) Pixel pitch 0.204(H) ×0.204(V) Pixel arrangement RGB Vertical Stripe Display colors 262,144 Display mode Normally Black Outline dimension 276.8±0.3(H) ×180.0±0.3(V) ×6.8(D:Max.) Weight 265(Typ.) / 275(Max.) Back-light SMD LED (48EA) Array Surface treatment Anti-Reflection, 2H Unit Remarks mm pixels mm colors mm Note 1 g Note 2 Note 1 : At PCB side (LED Side: 4.6mm Max.) Note 2 : Without digitizer SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 5 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 2.0 ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. Ta=25+/-2°C Parameter Symbol Min. Max. Unit Logic Power Supply Voltage VDD -0.3 4.0 V Logic Power Supply Voltage VIN -0.3 VDD+0.3 V HVDD -0.3 40 V Back-light LED Current ILED - 30 mA Back-light LED Reverse Voltage VR - 5 V Operating Temperature TOP 0 +50 ℃ Storage Temperature TSP -20 +60 ℃ Back-light Power Supply Voltage Remarks Note 1 Note 1, Note 2 Note 1. Ambient temperature vs allowable forward current are shown in the figure below. Note 2. Temperature and relative humidity range are shown in the figure below. 90% RH Max. ( 40℃ ≥ Ta) Maximum wet - bulb temperature at 39℃ or less. ( > 40℃) No condensation. Relative Humudity 100 (40, 90) 90 80 60 Operating Range (50, 50) 40 (60, 27) 20 Storage Range 5 -40 -20 0 20 40 60 80 Temperature (℃) SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 6 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 3.0 ELECTRICAL SPECIFICATIONS 3.1 Electrical Specifications < Table 3. Electrical Specifications > Parameter Min. Typ. Max. Unit Remarks Logic Power Supply Voltage VDD 3.0 3.3 3.6 V Note 1 Logic Power Supply Current IDD - 364 TBD mA Note 1 Back-light Power Supply Voltage HVDD 7.0 12.0 20 V Note 2 Back-light Power Supply Current IHVDD - 255 305 mA Note 2, 3 Back-light Power Consumption PBL - 3.06 3.66 W Note 2, 3 LED Driver’s Efficiency η - 82 - % Note 2, 3 Back-light PWM Frequency FPWM 200 280 350 ㎐ High Level PWM Signal Voltage VPWMH 2.1 3.3 5.0 V Low Level PWM Signal Voltage VPWML - 0 0.6 V High Level Differential Input Signal Voltage VIH - - +100 mV Low Level Differential Input Signal Voltage VIL -100 - - mV Back-light LED Voltage / Back-light LED Total Voltage VLED /VBL - 3.1 / 37.2 3.5/ 42.0 V Note 4 Back-light LED Current / Back-light LED Total Current ILED /IBL - 16.9 / 67.6 17.8/7 1.2 mA Note 4 10,000 - - Hrs Note 6 PD 0.95 TBD PLED 0.50 0.88 Ptotal 1.45 TBD Life Time EBL (Extended Battery Life) Power Consumption SPEC. NUMBER B2005-C001-A (3/3) VCM = 1.2V Note 1, 2, 3 PD - 1.0 TBD W Note 1 PLED - 2.51 2.99 W Note 4 Ptotal - 3.51 TBD W Note 1, 4 SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 7 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for 3.3V at 25℃. a) Typ : Window XP pattern, b) Max : Vertical Sub line pattern c) EBL : Mosaic pattern ( 32 X 32 ) 2. The power supply voltage and current is measured and specified at the interface connector of LCM including LED Driver. 3. Reference value, which is measured with LED Driver for 12V. 4. Reference value, which is measured without LED Driver. 5. Calculated value for reference (VLED × ILED × # of LEDs (48EA) ). 6. End of Life shall be determined by the time when any of the following is satisfied under continuous lighting at 25℃ and ILED = 16.9mA. -. Intensity drops to 50% of the Initial Value (Luminance Spec.) -. Based on LED 3.2 PWM Duty Ratio vs Brightness 100 Relative Brightness (%) 90 80 70 60 50 40 30 20 10 0 0 10 20 30 40 50 60 70 80 90 100 Duty Ratio (%) SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 8 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 4.0 OPTICAL SPECIFICATIONS 4.1 Overview The test of optical specifications shall be measured in a dark room (ambient luminance ≤ 1 lux and temperature = 25±2℃) with the equipment of Luminance meter system (Goniometer system and TOPCON BM-5A) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer to θØ=0 (=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock direction (“upward”), θØ=180 (= θ9 ) as the 9 o’clock direction (“left”) and θØ=270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θ and/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The backlight should be operating for 30 minutes prior to measurement. VDD shall be 3.3+/- 0.3V at 25°C. Optimum viewing angle direction is 6 o’clock. 4.2 Optical Specifications <Table 4. Optical Specifications> Parameter Viewing Angle Range Symbol Horizontal Vertical Luminance Contrast Ratio Luminance of 5 Points White 5 Points White Luminance 13 Points Uniformity White Color Chromaticity Red Green Blue Color Reproduction Response Time Cross Talk Brightness Outdoor Spec. Reflectance SPEC. NUMBER B2005-C001-A (3/3) Min. Typ. 500 90 90 90 90 700 - Deg. Deg. Deg. Deg. Yw 250 300 - cd/m2 ΔY5 80 - - ΔY13 60 - - Wx Wy Rx Ry Gx Gy Bx By 0.273 0.289 0.540 0.333 0.304 0.525 0.109 0.097 0.313 0.329 0.580 0.373 0.344 0.565 0.149 0.137 42 0.353 0.369 0.620 0.413 0.384 0.605 0.189 0.177 - 30 - ms Note 5 3.0 500 3.5 2.0 - % ms % Note 6 Note 7 Note 8 Θ3 Θ9 Θ12 Θ6 CR Total (Tr + Td) CT Center Ri Condition CR > 10 Θ = 0° Ta= 25° C Θ = 0° Θ = 0° Θ = 0° SPEC TITLE HX121WX1-100 Pre-Product Specification Max. Unit Remarks Note 1 Note 2 % Note 3 Note 4 % PAGE 9 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 Note : 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface (see FIGURE 1 shown in page 11). 2. Contrast measurements shall be made at viewing angle of Θ= 0° and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1 shown in page 11) Luminance Contrast Ratio (CR) is defined mathematically. CR = Luminance when displaying a white raster Luminance when displaying a black raster 3. The White luminance uniformity on LCD surface is then expressed. (See FIGURE 2~3 shown in page 12) Uniformity ΔY = Minimum Luminance of 5(or 13) points Maximum Luminance of 5(or 13) points X 100 (%) 4. The color chromaticity coordinates specified in Table 4 shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. 5. The electro-optical response time measurements shall be made as FIGURE 4 shown in page 13 by switching the “data” input signal OFF and ON. The times needed for the luminance to change from 10% to 90% is Tr, and 90% to 10% is Td. (See FIGURE 4 shown in page 13) 6. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark. (See FIGURE 5 shown in page 13) 7. Measure condition: Light source is 5,000nits, 15 degree position & BLU on (See FIGURE 1 shown in page 11) 8. Reference : Standard White Plate (BaSO4) Reflectance = Light intensity of the reflected light on LCD Module Output intensity of the reflected light on Reference × 100% Measure condition: Light source is 5,000nits, 15 degree position & BLU off (See FIGURE 1 shown in page 11) SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 10 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 4.3 Optical Measurements Figure 1. Measurement Set Up (L = 5 0 c m ) <Indoor> 30º Detector Light Source (Halogen Lamp) 50cm 15cm Module (BL on & off) <Outdoor> SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 11 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 Figure 2. White Luminance and Uniformity Measurement Locations (5 points) Column 320 640 960 Row 200 400 600 Note. Luminance of white is defined as luminance values of 5 points across the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in Figure 2 for a total of the measurements per display. * Yw = (Sum of 5 Points Luminance / 5 ) Figure 3. Uniformity Measurement Locations (13 points) 200 400 600 SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 12 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 Figure 4. Response Time Testing TFT Off(Black) TFT On(White) TFT Off(Black) Td Tr 100% 90% 10% 0% Figure 5. Cross Modulation Test Description VIEW AREA VIEW AREA 320,200 960,200 L31 YB(1120, 400) 320,600 L0 YA (1120, 400) Cross-Talk (%) = 960,600 YB - Y A × 100 YB Where: YA = Initial luminance of measured area (cd/m2) YB = Subsequent luminance of measured area (cd/m2) The location measured will be exactly the same in both patterns SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 13 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 5.0 INTERFACE CONNECTIONS 5.1 Electrical Interface Connection CN1 Interface Connector (FI-JH40S-HF10, Manufactured by JAE) Pin No. Symbol GROUND 21 GND6 Connector Test 22 RCLKIN- LVDS Negative clock signal (-) LVDD1 Logic Power Supply : +3.3V 23 RCLKIN+ LVDS Positive clock signal (+) 4 LVDD2 Logic Power Supply : +3.3V 24 GND7 GROUND 5 LVDD3 Logic Power Supply : +3.3V 25 VDIM PWM Brightness Control 6 VDD_DEID EDID Power Supply : +3.3V 26 Reserved NON-CONNECTION 7 TEST NON-CONNECTION 27 Reserved NON-CONNECTION 8 CLK_EDID EDID Clock 28 HVGND1 GROUND 9 DATA_EDID EDID Data 29 HVGND2 GROUND 10 GND2 GROUND 30 HVGND3 GROUND 11 GND3 GROUND 31 HVGND4 GROUND 12 NC NON-CONNECTION 32 HVGND5 GROUND 13 RIN0- LVDS Negative data signal (-) 33 NC 14 RIN0+ LVDS Positive data signal (+) 34 HVDD1 Back-light Power Supply: +12V 15 GND4 GROUND 35 HVDD2 Back-light Power Supply: +12V 16 RIN1- LVDS Negative data signal (-) 36 HVDD3 Back-light Power Supply: +12V 17 RIN1+ LVDS Positive data signal (+) 37 HVDD4 Back-light Power Supply: +12V 18 GND5 GROUND 38 HVDD5 Back-light Power Supply: +12V 19 RIN2- LVDS Negative data signal (-) 39 CONNTST 20 RIN2+ LVDS Positive data signal (+) 40 GND8 Pin No. Symbol 1 GND1 2 CONNTST 3 Function Function GROUND NON-CONNECTION Connector Test GROUND Note 1. Connected with No. 2 & 39 Note 2. Start from left side PCB #1 #40 CN1 (FI-JH40S-HF10) SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 14 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 5.2 LVDS Interface LVDS Transmitter : THC63LVDM83A Transmitter Input signal Pin No R0 51 R1 52 R2 54 R3 55 R4 56 R5 3 G0 4 G1 6 G2 7 G3 11 G4 12 G5 14 B0 15 B1 19 B2 20 B3 22 B4 23 B5 24 HSYNC 27 VSYNC 28 DE 30 MCLK 31 SPEC. NUMBER B2005-C001-A (3/3) Pin No Interface FI-JH40SHF10 System (Tx) TFT-LCD (Rx) 48 47 OUT0OUT0+ IN0IN0+ 13 14 46 45 OUT1OUT1+ IN1IN1+ 16 17 42 41 OUT2OUT2+ IN2IN2+ 19 20 40 CLKOUT- CLKIN- 22 39 CLKOUT+ CLKIN+ 23 SPEC TITLE HX121WX1-100 Pre-Product Specification Remark Pin No. PAGE 15 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 5.3 Back-light Interface CN2 LED FPC Connector (04-6298-009, Manufactured by Kyocera) Pin No. Symbol Function 1 Anode1 LED Anode Power Supply 2 Anode2 LED Anode Power Supply 3 Anode3 LED Anode Power Supply 4 Anode4 LED Anode Power Supply 5 NC 6 Cathode1 LED Cathode Power Supply 7 Cathode2 LED Cathode Power Supply 8 Cathode3 LED Cathode Power Supply 9 Cathode4 LED Cathode Power Supply Remark LED Anode Power Supply (3.25V X 12EA = 39V) Non-Connection LED Cathode Power Supply 5.4 Data Input Format (1,1) (2,1) (1279,1)(1280,1) R G B R G B R G B R G B 1 Pixel = 3 Dots R G B R G B R G B (1,800) (2,800) SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification R G B R G B (1279,800)(1280,800) PAGE 16 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 6.0. SIGNAL TIMING SPECIFICATIONS 6.1 The 12.1” WXGA LCM is operated by the only DE (Data enable) mode (LVDS Transmitter Input) Item Symbol Min. Typ. Max. Unit Frame Period T1 810 823 - Lines Vertical Display Period T2 - 800 - Lines One line Scanning Period T3 1350 1440 - Clocks Horizontal Display Period T4 - 1280 - Clocks 1/T5 - 69.3 - MHz Clock Frequency 7.0 SIGNAL TIMING WAVEFORMS 7.1 Timing Waveforms of Interface Signal T1 T2 DE T3 DCLK T5 T4 DE DATA SIGNALS SPEC. NUMBER B2005-C001-A (3/3) Valid display data (1280 Clocks) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 17 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 7.2 LVDS Rx Interface Timing Parameter The specification of the LVDS Rx interface timing parameter < LVDS Rx Interface Timing Specification> Item Symbol Min. Typ. Max. Unit Remarks CLKIN Period tRCIP 12.50 14.43 25.00 nsec Input Data 0 tRIP0 -0.4 0.0 +0.4 nsec Input Data 1 tRIP1 tRICP/7-0.4 tRICP/7 tRICP/7+0.4 nsec Input Data 2 tRIP2 2 ×tRICP/7-0.4 2 ×tRICP/7 2 ×tRICP/7+0.4 nsec Input Data 3 tRIP3 3 ×tRICP/7-0.4 3 ×tRICP/7 3 ×tRICP/7+0.4 nsec Input Data 4 tRIP4 4 ×tRICP/7-0.4 4 ×tRICP/7 4 ×tRICP/7+0.4 nsec Input Data 5 tRIP5 5 ×tRICP/7-0.4 5 ×tRICP/7 5 ×tRICP/7+0.4 nsec Input Data 6 tRIP6 6 ×tRICP/7-0.4 6 ×tRICP/7 6 ×tRICP/7+0.4 nsec tRIP6 tRIP5 tRIP4 tRIP3 tRIP2 tRIP1 tRIP0 RxINz +/* Z = 0, 1, 2 Rx RxCLKIN+/- Rx Rx Rx Rx Rx Rx Rx Vdiff=0[v] Rx Rx Rx Vdiff=0[v] tRCIP SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 18 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS Each color is displayed in sixty-four gray scales from a 6 bit data signal input. A total of 262,144 colors are derived from the resultant 18 bit data. Colors & Gray Scale Black Blue Green Basic Cyan Colors Red Magenta Yellow White Black △ Darker Gray △ Scale Of ▽ Red Brighter ▽ Red Black △ Darker Gray △ Scale Of ▽ Green Brighter ▽ Green Black △ Darker Gray △ Scale Of ▽ Blue Brighter ▽ Blue Black △ Gray Darker Scale △ Of White ▽ & Brighter Black ▽ White SPEC. NUMBER B2005-C001-A (3/3) Red Data Green Data R5 R4 R3 R2 R1 R0 G5 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 1 0 0 0 0 1 1 1 1 0 1 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 ↓ ↓ 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 1 1 1 0 0 1 1 0 0 1 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 1 1 1 1 1 1 1 1 1 1 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 1 1 1 0 0 0 0 1 1 0 0 1 1 0 1 0 1 0 1 1 1 0 1 1 1 0 1 ↓ ↓ 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 ↓ ↓ 1 1 1 0 1 0 1 0 1 0 1 0 0 0 ↓ ↓ ↓ ↓ 0 0 0 0 0 0 0 1 0 1 0 1 0 1 0 0 0 ↓ ↓ 0 0 0 0 0 0 1 1 1 0 0 0 ↓ ↓ 1 1 1 0 0 1 1 0 0 1 1 0 0 0 ↓ ↓ ↓ ↓ 0 0 0 0 0 0 0 0 1 1 0 0 1 1 0 0 0 ↓ ↓ ↓ ↓ 0 0 0 0 0 0 Blue Data G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 ↓ ↓ 1 1 1 0 1 1 SPEC TITLE HX121WX1-100 Pre-Product Specification 1 0 1 1 1 1 1 1 1 1 1 1 PAGE 19 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 9.0 POWER SEQUENCE To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below 0.9VDD Power Supply 0V 0.9VDD 0.1VDD 0.1VDD T1 T5 T7 T2 T6 Interface Signal Valid 0V T3 Back- light T4 0V ● T1 ≤ 10 ms ● 0 ≤ T2 ≤ 50 ms ● 200 ms ≤ T3 ● 200 ms ≤ T4 ● 0 ≤ T5 ≤ 50 ms ● 0 ≤ T6 ≤ 10ms ● 500ms ≤ T7 Notes : 1. When the power supply VDD is 0V, Keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. 3. Back Light must be turn on after power for logic and interface signal are valid. SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 20 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 10.0 MECHANICAL CHARACTERISTICS 10.1 Dimensional Requirements Figure 6 & 7 (located in 11.0) shows mechanical outlines for the model Parameter Specification Active Area 261.12(H) X 163.20(V) Number of pixels 1280(H) X 800(V) (1 pixel = R + G + B dots) Pixel pitch 0.204(H) X 0.204(V) Pixel arrangement RGB Vertical stripe Display colors 262,144 Display mode Normally Black Outline dimension 276.8±0.3(H)×180.0(V)±0.3×6.8(D:Max.) Weight 265(Typ.) / 275(Max.) Back-light SMD LED (48EA) Array Unit mm mm g 10.2 Mounting See Figure 6 & 7 & 8. (shown in 11.0) Parameter Specification Unit Torque of side mounting screw 2.5(Max.) kgf Torque of ground plate screw 1.5(Max.) kgf Torque of top side screw 2.5(Max.) kgf 10.3 Anti-Glare and Polarizer Hardness. The surface of the LCD has an anti-glare coating to minimize reflection and a coating to reduce scratching. 10.4 Light Leakage There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50cm from the screen with an overhead light level of 150lux. The manufacture shall furnish limit samples of the panel showing the light leakage acceptable. SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 21 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 11.0 Mechanical Drawing Figure 6. TFT-LCD Module Outline Dimension (Front View) SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 22 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 Figure 7. TFT-LCD Module Outline Dimensions (Rear view) HX121WX1-100 SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 23 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 Figure 8. TFT-LCD Module Section for Mounting SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 24 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 12.0 RELIABLITY TEST The Reliability test items and its conditions are shown in below. <Table 12. Reliability Test> No Test Item Conditions 1 High temperature storage test Ta = 60 °C, 240 hrs 2 Low temperature storage test Ta = -20 °C, 240 hrs 3 High temperature & high humidity operation test Ta = 50 ℃, 80%RH, 240hrs 4 High temperature operation test Ta = 50 °C, 240 hrs 5 Low temperature operation test Ta = 0 °C, 240 hrs 6 Thermal shock Ta = -20 °C ↔ 60 °C (30 min), 100 cycle 7 Vibration test (non-operating) Frequency : 10~500Hz Gravity/AMP : 1.5G Period : X,Y,Z 30min 8 Shock test (non-operating) Gravity : 220G Pulse width : 2ms, half sine wave ±X, ±Y, ±Z Once for each direction 9 Electro-static discharge test (non-operating) Air : 150pF, 330ohm, 15KV Contact : 150pF, 330ohm, 8KV 13.0 HANDLING & CAUTIONS 13.1 Cautions when taking out the module y Pick the pouch only, when taking out module from a shipping package. 13.2 Cautions for handling the module y As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. y As the LCD panel and back - light element are made from fragile glass (epoxy) material, impulse and pressure to the LCD module should be avoided. y As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. y Do not pull the interface connector in or out while the LCD module is operating. y Put the module display side down on a flat horizontal plane. y Handle connectors and cables with care. SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 25 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 13.3 Cautions for the operation y When the module is operating, do not lose MCLK, DE signals. If any one of these signals were lost, the LCD panel would be damaged. y Obey the supply voltage sequence. If wrong sequence is applied, the module would be damaged. 13.4 Cautions for the atmosphere y Dew drop atmosphere should be avoided. y Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere is recommended. 13.5 Cautions for the module characteristics y Do not apply fixed pattern data signal to the LCD module at product aging. y Applying fixed pattern for a long time may cause image sticking. 13.6 Cautions for the digitizer assembly y When assembling FPC connector, do not flip connector past 90° due to possible damage to connector. y When positioning digitizer underneath driver IC, do not lift driver IC past 90° due to possible damage to drive IC pattern. y Please be warned that during assembly of digitizer, the opening or closing of FPC will result in possible electrostatic discharge damage to the LED 13.7 Other cautions y Do not re-adjust variable resistor or switch etc. y When returning the module for repair or etc., Please pack the module not to be broken. We recommend to use the original shipping packages. SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 26 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 14.0 LABELS 14.1 Product Label HX121WX1-100 BOE HYDIS Barcode 1 2 3 4 5 X X X X X X X 6 7 X X X X X X X X X X No 1. Control Number No 5. Month (1, 2, 3,…, 9, X, Y, Z) No 2. Rank / Grade No 6. FG Code No 3. Line Classification (BOE HYDIS : H, LCM : L, BOE OT : A/B/C) No 7. Serial Number No 4. Year (5 : 2005, 6 : 2006, …) SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 27 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 14.2 Packing Label Label Size: 108 mm (L) × 56 mm (W) Contents Model: HX121WX1-100 Q`ty: Module Q`ty in one box Serial No.: Box Serial No. See next figure for detail description. Date: Packing Date FG Code: FG Code of Product 10 HX121WX1-100 * 0000000000000 * 200X.X.XX 1 0 XXXX 00 0 00 0 0 000000 Type Grade Year Month ITEM-CODE Serial_no SPEC. NUMBER B2005-C001-A (3/3) FG CODE SPEC TITLE HX121WX1-100 Pre-Product Specification RoHS Mark PAGE 28 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P2 2008. 01. 14 15.0 PACKING INFORMATION 15.1 Packing order Put Pad into the box. Put silica gels in the box. After sealing the box, attach Packing Label on the attach position sign area of the box. Place a cover on the top of the box. As shown in the figure, place the Modules bundled by shielding bag in the box. 15.2 Notes z Box Dimension : 349.0mm(W) X 261.0mm(D) X 311.0mm(H) z Package Quantity in one Box : 10pcs SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE HX121WX1-100 Pre-Product Specification PAGE 29 OF 29 A4(210 X 297)