DATASHEET ICS542 CLOCK DIVIDER Description Features The ICS542 is cost effective way to produce a high-quality clock output divided from a clock input. The chip accepts a clock input up to 156 MHz at 3.3 V and produces a divide by 2, 4, 6, 8, 12, or 16 of the input clock. There are two outputs on the chip, one being a low-skew divide by two of the other. • • • • • • • • • • • • • For instance, if an 100 MHz input clock is used, the ICS542 can produce low-skew 50 MHz and 25 MHz clocks, or low skew 25 MHz and 12.5 MHz clocks. The chip has an all-chip power-down mode that stops the outputs low, and an OE pin that tri-states the outputs. See the ICS541 and ICS543 for other clock dividers, and the ICS501, 502, 511, 512, and 525 for clock multipliers. 8-pin SOIC package, Pb free Available in RoHS compliant package IDT’s lowest cost clock divider Low skew (500 ps) outputs. One is /2 of the other Easy to use with other generators and buffers Input clock frequency up to 156 MHz Output clock duty cycle of 45/55 Power-down turns off chip Output Enable Advanced, low-power CMOS process Operating voltage of 3.3 V or 5 V Does not degrade phase noise - no PLL Available in industrial and commercial temperature ranges Block Diagram VDD CLK1 S1, S0 Divider and Selection Circuitry /2 CLK2 Input Clock GND IDT™ / ICS™ CLOCK DIVIDER 1 OE (both outputs) ICS542 REV J 051310 ICS542 CLOCK DIVIDER CLOCK DIVIDER Pin Assignment Clock Decoding Table S1 S0 I CLK 1 8 CLK 0 0 VDD 2 7 CLK/ 2 0 1 Input/6 Input/12 GND 3 6 OE 1 0 Input/8 Input/16 1 1 Input/2 Input/4 S0 5 4 S1 CLK CLK/2 Power Down All 0 = connect directly to ground 1 = connect directly to VDD 8-pin (150 mil) SOIC Pin Descriptions Pin Number Pin Name Pin Type 1 ICLK XI 2 VDD Power Connect to +3.3 V or +5 V. 3 GND Power 4 S0 Input 5 S1 Input 6 OE Input 7 CLK/2 Output Connect to ground. Select 0 for output clock. Connect to GND or VDD, per decoding table above. Internal pull-up resistor. Select 1 for output clock. Connect to GND or VDD, per decoding table above. Internal pull-up resistor. Output Enable. Tri-states both output clocks when low. Internal pull-up resistor. Clock output per table above. Low skew divide by two of pin 8 clock. 8 CLK Output Clock output per table above. Pin Description Clock input. External Components Series Termination Resistor PCB Layout Recommendations Clock output traces over one inch should use series termination. To series terminate a 50Ω trace (a commonly used trace impedance), place a 33Ω resistor in series with the clock line, as close to the clock output pin as possible. The nominal impedance of the clock output is 20Ω. For optimum device performance and lowest output phase noise, the following guidelines should be observed. As with any high-performance mixed-signal IC, the ICS542 must be isolated from system power supply noise to perform optimally. 1) The 0.01µF decoupling capacitor should be mounted on the component side of the board as close to the VDD pin as possible. No vias should be used between decoupling capacitor and VDD pin. The PCB trace to VDD pin should be kept as short as possible, as should the PCB trace to the ground via. Distance of the ferrite bead and bulk decoupling from the device is less critical. A decoupling capacitor of 0.01µF must be connected between VDD and the PCB ground plane. 2) To minimize EMI, the 33Ω series termination resistor (if needed) should be placed close to the clock output. Decoupling Capacitor 3) An optimum layout is one with all components on the IDT™ / ICS™ CLOCK DIVIDER 2 ICS542 REV J 051310 ICS542 CLOCK DIVIDER CLOCK DIVIDER same side of the board, minimizing vias through other signal layers (the ferrite bead and bulk decoupling capacitor can be mounted on the back). Other signal traces should be routed away from the ICS542. This includes signal traces just underneath the device, or on layers adjacent to the ground plane layer used by the device. Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS542. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD 7V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature (commercial) 0 to +70° C Ambient Operating Temperature (industrial) -40 to +85° C Storage Temperature -65 to +150° C Junction Temperature 125° C Soldering Temperature 260° C Recommended Operation Conditions Parameter Min. Max. Units 0 +70 °C Ambient Operating Temperature (industrial) -40 +85 °C Power Supply Voltage (measured in respect to GND) 3.0 5.5 V Ambient Operating Temperature (commercial) IDT™ / ICS™ CLOCK DIVIDER 3 Typ. ICS542 REV J 051310 ICS542 CLOCK DIVIDER CLOCK DIVIDER DC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V ±5%, Ambient Temp. 0 to +70° C (commercial), -40 to +85° C (industrial) Parameter Symbol Conditions Min. Typ. 3.0 Max. Units 5.5 V Operating Voltage VDD Input High Voltage, VIH ICLK (pin 1) Input Low Voltage VIL ICLK (pin 1) Input High Voltage VIH S0, S1, OE Input Low Voltage VIL S0, S1, OE Output High Voltage VOH IOH = -25 mA Output Low Voltage VOL IOL = 25 mA Operating Supply Current IDD No Load, 5.0 V, 11 sel 11 mA Operating Supply Current IDD No Load, 3.3 V, 11 sel 7 mA Short Circuit Current IOS ±40 mA Input Capacitance CIN S0, S1, OE 4 pF Nominal Output Impedance ZO at VDD/2 20 Ω VDD/2+1 VDD/2 VDD/2 V VDD/2-1 2 V V 0.8 2.4 V V 0.4 V AC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V ±5%, Ambient Temp. 0 to +70° C (commercial), -40 to +85° C (industrial) Parameter Symbol Conditions Min. Typ. Max. Units Input Frequency, clock input VDD = 5 V 0 156 MHz Input Frequency, clock input VDD = 3.3 V 0 156 MHz Output Rise Time tOR 0.8 to 2.0 V 1 ns Output Fall Time tOF 2.0 to 0.8 V 1 ns Duty Cycle at VDD/2 Skew of Output Clocks Propagation Delay 45 49 to 51 55 % rising edges at VDD/2 500 ps ICLK to CLK 15 ns Thermal Characteristics Parameter Thermal Resistance Junction to Ambient Thermal Resistance Junction to Case IDT™ / ICS™ CLOCK DIVIDER Symbol Conditions Min. Typ. Max. Units θJA Still air 150 ° C/W θJA 1 m/s air flow 140 ° C/W θJA 3 m/s air flow 120 ° C/W 40 ° C/W θJC 4 ICS542 REV J 051310 ICS542 CLOCK DIVIDER CLOCK DIVIDER Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Body) Package dimensions are kept current with JEDEC Publication No. 95 Millimeters 8 E Inches Symbol Min Max Min Max A 1.35 1.75 .0532 .0688 A1 0.10 0.25 .0040 .0098 B 0.33 0.51 .013 .020 C 0.19 0.25 .0075 .0098 D 4.80 5.00 .1890 .1968 E 3.80 4.00 .1497 .1574 H INDEX AREA e 1 2 D A 1.27 BASIC 0.050 BASIC H 5.80 6.20 .2284 .2440 h 0.25 0.50 .010 .020 L 0.40 1.27 .016 .050 α 0° 8° 0° 8° h x 45 A1 C -Ce B SEATING PLANE L .10 (.004) C Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature 542MLF 542MLFT 542MILF 542MILFT 542MLF 542MLF 542MILF 542MILF Tubes Tape and Reel Tubes Tape and Reel 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 0 to +70° C 0 to +70° C -40 to +85° C -40 to +85° C Parts that are ordered with a “LF” suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. IDT™ / ICS™ CLOCK DIVIDER 5 ICS542 REV J 051310 ICS542 CLOCK DIVIDER CLOCK DIVIDER Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 www.idt.com/go/clockhelp Corporate Headquarters Integrated Device Technology, Inc. www.idt.com © 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA