128K X 36, 256K X 18 3.3V Synchronous SRAMs 3.3V I/O, Flow-Through Outputs Burst Counter, Single Cycle Deselect IDT71V3577S IDT71V3579S IDT71V3577SA IDT71V3579SA Features Description ◆ The IDT71V3577/79 are high-speed SRAMs organized as 128K x 36/256K x 18. The IDT71V3577/79 SRAMs contain write, data, address and control registers. There are no registers in the data output path (flow-through architecture). Internal logic allows the SRAM to generate a self-timed write based upon a decision which can be left until the end of the write cycle. The burst mode feature offers the highest level of performance to the system designer, as the IDT71V3577/79 can provide four cycles of data for a single address presented to the SRAM. An internal burst address counter accepts the first cycle address from the processor, initiating the access sequence. The first cycle of output data will flow-through from the array after a clock-to-data access time delay from the rising clock edge of the same cycle. If burst mode operation is selected (ADV=LOW), the subsequent three cycles of output data will be available to the user on the next three rising clock edges. The order of these three addresses are defined by the internal burst counter and the LBO input pin. The IDT71V3577/79 SRAMs utilize IDT’s latest high-performance CMOS process and are packaged in a JEDEC standard 14mm x 20mm 100-pin thin plastic quad flatpack (TQFP) as well as a 119 ball grid array (BGA) and a 165 fine pitch ball grid array (fBGA). ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ 128K x 36, 256K x 18 memory configurations Supports fast access times: Commercial: – 7.5ns up to 117MHz clock frequency Commercial and Industrial: – 8.0ns up to 100MHz clock frequency – 8.5ns up to 87MHz clock frequency LBO input selects interleaved or linear burst mode GW Self-timed write cycle with global write control (GW GW), byte write BWE BW enable (BWE BWE), and byte writes (BW BWx) 3.3V core power supply Power down controlled by ZZ input 3.3V I/O Optional - Boundary Scan JTAG Interface (IEEE 1149.1 compliant) Packaged in a JEDEC Standard 100-pin plastic thin quad flatpack (TQFP), 119 ball grid array (BGA) and 165 fine pitch ball grid array Pin Description Summary A0-A17 Address Inputs Input Synchronous CE Chip Enable Input Synchronous CS0, CS1 Chip Selects Input Synchronous OE Output Enable Input Asynchronous GW Global Write Enable Input Synchronous BWE Byte Write Enable Input Synchronous BW1, BW2, BW3, BW4(1) Individual Byte Write Selects Input Synchronous CLK Clock Input N/A ADV Burst Address Advance Input Synchronous ADSC Address Status (Cache Controller) Input Synchronous ADSP Address Status (Processor) Input Synchronous LBO Linear / Interleaved Burst Order Input DC TMS Test Mode Select Input Synchronous TDI Test Data Input Input Synchronous TCK Test Clock Input N/A TDO Test Data Output Output Synchronous TRST JTAG Reset (Optional) Input Asynchronous ZZ Sleep Mode Input Asynchronous I/O0-I/O31, I/OP1-I/OP4 Data Input / Output I/O Synchronous VDD, VDDQ Core Power, I/O Power Supply N/A VSS Ground Supply N/A NOTE: 1. BW3 and BW4 are not applicable for the IDT71V3579. 5280 tbl 01 1 ©2005 Integrated Device Technology, Inc. FEBRUARY 2005 DSC-5280/08 IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges Pin Definitions(1) Symbol Pin Function I/O Active Description A0-A17 Address Inputs I N/A Synchronous Address inputs. The address register is triggered by a combi-nation of the rising edge of CLK and ADSC Low or ADSP Low and CE Low. ADSC Address Status (Cache Controller) I LOW Synchronous Addre ss Status from Cache Controller. ADSC is an active LOW input that is used to load the address registers with new addresses. ADSP Address Status (Processor) I LOW Synchronous Address Status from Processor. ADSP is an active LOW input that is used to load the address registers with new addresses. ADSP is gated by CE. ADV Burst Address Advance I LOW Synchronous Address Advance. ADV is an active LOW input that is used to advance the internal burst counter, controlling burst access after the initial address is loaded. When the input is HIGH the burst counter is not incremented; that is, there is no address advance. BWE Byte Write Enable I LOW Synchronous byte write enable gates the byte write inputs BW1-BW4. If BWE is LOW at the rising edge of CLK then BWx inputs are passed to the next stage in the circuit. If BWE is HIGH then the byte write inputs are blocked and only GW can initiate a write cycle. BW1-BW4 Individual Byte Write Enables I LOW Synchronous byte write enables. BW1 controls I/O0-7, I/OP1, BW2 controls I/O8-15, I/OP2, etc. Any active byte write causes all outputs to be disabled. CE Chip Enable I LOW Synchronous chip enable. CE is used with CS 0 and CS1 to enable the IDT71V3577/79. CE also gates ADSP. CLK Clock I N/A This is the clock input. All timing references for the device are made with respect to this input. CS 0 Chip Select 0 I HIGH Synchronous active HIGH chip select. CS 0 is used with CE and CS1 to enable the chip. CS1 Chip Select 1 I LOW Synchronous active LOW chip select. CS1 is used with CE and CS0 to enable the chip. GW Global Write Enable I LOW Synchronous global write enable. This input will write all four 9-bit data bytes when LOW on the rising edge of CLK. GW supersedes individual byte write enables. I/O0-I/O31 I/OP1-I/OP4 Data Input/Output I/O N/A Synchronous data input/output (I/O) pins. The data input path is registered, triggered by the rising edge of CLK. The data o utput path is flow-through (no output register). LBO Linear Burst Order I LOW Asynchronous b urst order selection input. When LBO is HIGH, the inter-leaved burst sequence is selected. When LBO is LOW the Linear burst sequence is selected. LBO is a static input and must not change state while the device is operating. OE Output Enable I LOW Asynchronous output enable. When OE is LOW the data output drivers are enabled on the I/O pins if the chip is also selected. When OE is HIGH the I/O pins are in a high-impedance state. TMS Test ModeSelect I N/A Gives input command for TAP controller. Sampled on rising edge of TDK. This pin has an internal pullup. TDI Test Data Input I N/A Serial input of registers placed between TDI and TDO. Sampled on rising edge of TCK. This pin has an internal pullup. TCK Test Clock I N/A Clock input of TAP controller. Each TAP event is clocked. Test inputs are captured on rising edge of TCK, while test outputs are driven from the falling edge of TCK. This pin has an internal pullup. TDO Test DataOutput O N/A Serial output of registers placed be tween TDI and TDO. This output is active depending on the state of the TAP controller. TRST JTAG Reset (Optional) I LOW Optional Asynchronous JTAG rese t. Can be used to reset the TAP contro ller, but not required. JTAG reset occurs automatically at power up and also resets using TMS and TCK per IEEE 1149.1. If not used TRST can be left floating. This pin has an internal pullup. Only available in BGA package. ZZ Sleep Mode I HIGH Asynchronous sleep mode input. ZZ HIGH will gate the CLK internally and power down the IDT71V3577/79 to its lowest power consumption level. Data retention is guaranteed in Sleep Mode.This pin has an internal pull down. VDD Power Supply N/A N/A 3.3V core power supply. VDDQ Power Supply N/A N/A 3.3V I/O Supply. VSS Ground N/A N/A Ground. NC No Connect N/A N/A NC pins are not electrically connected to the device. NOTE: 1. All synchronous inputs must meet specified setup and hold times with respect to CLK. 6.42 2 5280 tbl 02 IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges Functional Block Diagram LBO ADV CLK 2 Binary Counter ADSC Burst Logic Q0 CLR ADSP Q1 CLK EN ADDRESS REGISTER A0 - A16/17 GW BWE INTERNAL ADDRESS Burst Sequence CEN 17/18 A0* A1* 128K x 36/ 256K x 18BIT MEMORY ARRAY 2 A0,A1 A2 - A17 36/18 17/18 Byte 1 Write Register 36/18 Byte 1 Write Driver BW1 9 Byte 2 Write Register Byte 2 Write Driver BW2 9 Byte 3 Write Register Byte 3 Write Driver BW3 9 Byte 4 Write Register Byte 4 Write Driver BW4 9 CE D CS0 CS1 Q Enable Register DATA INPUT REGISTER CLK EN ZZ Powerdown OE OE I/O0 - I/O31 I/OP1 - I/OP4 OUTPUT BUFFER 36/18 TMS TDI TCK 5280 drw 01 JTAG (SA Version) TDO TRST (Optional) 6.42 3 , IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Absolute Maximum Ratings (1) Symbol (2) Rating Commercial & Industrial Values Unit VTERM Terminal Voltage with Respect to GND -0.5 to +4.6 V VTERM(3,6) Terminal Voltage with Respect to GND -0.5 to VDD V VTERM(4,6) Terminal Voltage with Respect to GND -0.5 to VDD +0.5 V VTERM(5,6) Terminal Voltage with Respect to GND -0.5 to VDDQ +0.5 V Commercial Operating Temperature -0 to +70 o Industrial Operating Temperature -40 to +85 o C Temperature Under Bias -55 to +125 o C Storage Temperature -55 to +125 TA (7) TBIAS TSTG Recommended Operating Temperature Supply Voltage Temperature(1) VSS VDD VDDQ Commercial 0°C to +70°C 0V 3.3V± 5% 3.3V± 5% Industrial -40°C to +85°C 0V 3.3V± 5% 3.3V± 5% Symbol W IOUT DC Output Current 50 mA 100 Pin TQFP Capacitance CIN Input Capacitance CI/O I/O Capacitance 3.3 3.465 V VDDQ I/O Supply Voltage 3.135 3.3 3.465 V 0 0 0 V 2.0 ____ VDD +0.3 2.0 ____ Input Capacitance CI/O I/O Capacitance Input High Voltage - Inputs Input High Voltage - I/O Input Low Voltage Parameter(1) Conditions Max. Unit Symbol VIN = 3dV 5 pF CIN Input Capacitance VOUT = 3dV 7 pF CI/O I/O Capacitance (TA = +25° C, f = 1.0mhz) CIN Supply Voltage (2) -0.3 ____ V (1) VDDQ +0.3 0.8 V V (T A = +25° C, f = 1.0mhz) 165 fBGA Capacitance Parameter(1) Unit 5280 tbl 06 NOTES: 1. VIH (max) = VDDQ + 1.0V for pulse width less than tCYC/2, once per cycle. 2. VIL (min) = -1.0V for pulse width less than t CYC/2, once per cycle. 5280 tbl 07 Symbol Max. 119 BGA Capacitance (TA = +25° C, f = 1.0mhz) (1) Typ. 3.135 VIL 5280 tbl 03 Min. Core Supply Voltage VIH NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VDD terminals only. 3. VDDQ terminals only. 4. Input terminals only. 5. I/O terminals only. 6. This is a steady-state DC parameter that applies after the power supplies have ramped up. Power supply sequencing is not necessary; however, the voltage on any input or I/O pin cannot exceed VDDQ during power supply ramp up. 7. TA is the "instant on" case temperature. Parameter VDD VSS C 2.0 5280 tbl 04 Recommended DC Operating Conditions VIH o Power Dissipation Parameter Grade NOTES: 1. TA is the "instant on" case temperature. C PT Symbol Commercial and Industrial Temperature Ranges Conditions Max. Unit VIN = 3dV 7 pF VOUT = 3dV 7 pF 5280 tb l 07b NOTE: 1. This parameter is guaranteed by device characterization, but not production tested. 6.42 4 Conditions Max. Unit VIN = 3dV 7 pF VOUT = 3dV 7 pF 5280 tbl 07a IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges A6 A7 CE CS0 BW4 BW3 BW2 BW1 CS1 VDD VSS CLK GW BWE OE ADSC ADSP ADV A8 A9 Pin Configuration 128K x 36 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 I/OP3 I/O16 I/O17 VDDQ VSS I/O18 I/O19 I/O20 I/O21 VSS VDDQ I/O22 I/O23 VSS(1) VDD NC VSS I/O24 I/O25 VDDQ VSS I/O26 I/O27 I/O28 I/O29 VSS VDDQ I/O30 I/O31 I/OP4 1 80 2 79 3 78 4 77 5 76 6 75 7 74 8 73 9 72 10 71 11 70 12 69 13 68 14 67 15 66 16 65 17 64 18 63 19 62 20 61 21 60 22 59 23 58 24 57 25 56 26 55 27 54 28 53 29 52 30 51 I/OP2 I/O15 I/O14 VDDQ VSS I/O13 I/O12 I/O11 I/O10 VSS VDDQ I/O9 I/O8 VSS NC VDD ZZ (2) I/O7 I/O6 VDDQ VSS I/O5 I/O4 I/O3 I/O2 VSS VDDQ I/O1 I/O0 I/OP1 NC NC A10 A11 A12 A13 A14 A15 A16 LBO A5 A4 A3 A2 A1 A0 NC NC VSS VDD 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 100 TQFP Top View NOTES: 1. Pin 14 does not have to be directly connected to VSS as long as the input voltage is < VIL. 2. Pin 64 can be left unconnected and the device will always remain in active mode. 6.42 5 5280 drw 02a , IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges A6 A7 CE CS0 NC NC BW2 BW1 CS1 VDD VSS CLK GW BWE OE ADSC ADSP ADV A8 A9 Pin Configuration 256K x 18 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 NC NC NC 1 80 2 79 3 VDDQ VSS NC NC I/O8 I/O9 VSS VDDQ I/O10 I/O11 VSS(1) VDD NC VSS I/O12 I/O13 VDDQ VSS I/O14 I/O15 I/OP2 NC VSS VDDQ NC NC NC 4 78 77 5 76 6 75 7 74 73 8 9 72 71 10 11 70 12 69 13 68 14 67 66 15 16 65 64 17 18 63 19 62 20 61 21 60 22 59 23 58 24 57 25 56 26 55 27 54 28 53 29 52 30 51 A10 NC NC VDDQ VSS NC I/OP1 I/O7 I/O6 VSS VDDQ I/O5 I/O4 VSS NC VDD ZZ(2) I/O3 I/O2 VDDQ VSS I/O1 I/O0 NC NC VSS VDDQ NC NC NC LBO A5 A4 A3 A2 A1 A0 NC NC VSS VDD NC NC A11 A12 A13 A14 A15 A16 A17 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 100 TQFP Top View NOTES: 1. Pin 14 does not have to be directly connected to VSS as long as the input voltage is < VIL . 2. Pin 64 can be left unconnected and the device will always remain in active mode. 6.42 6 5280 drw 02b , IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges Pin Configuration 128K x 36, 119 BGA 1 2 3 4 5 6 7 A VDDQ A6 A4 ADSP A8 A16 VDDQ B NC CS0 A3 ADSC A9 CS1 NC C NC A7 A2 VDD A12 A15 NC D I/O16 I/OP3 VSS NC VSS I/OP2 I/O15 E I/O17 I/O18 VSS CE VSS I/O13 I/O14 F VDDQ I/O19 VSS OE VSS I/O12 VDDQ G I/O20 I/O21 BW3 ADV BW2 I/O11 I/O10 H I/O22 I/O23 VSS GW VSS I/O9 I/O8 J VDDQ VDD NC VDD NC VDD VDDQ K I/O24 I/O26 VSS CLK VSS I/O6 I/O7 L I/O25 I/O27 BW4 NC BW1 I/O4 I/O5 M VDDQ I/O28 VSS BWE VSS I/O3 VDDQ N I/O29 I/O30 VSS A1 VSS I/O2 I/O1 P I/O31 I/OP4 VSS A0 VSS I/O0 I/OP1 R NC A5 LBO VDD VSS A13 NC T NC NC A10 A11 A14 NC ZZ(3) U VDDQ NC/TDO(2) NC/TR ST(2,4) VDDQ NC/TMS(2) NC/TDI(2) NC/TCK(2) 5280 drw 02c Top View Pin Configuration 256K x 18, 119 BGA A 1 2 3 4 5 6 7 VDDQ A6 A4 ADSP A8 A16 VDDQ CS1 NC B NC CS0 A3 ADSC A9 C NC A7 A2 VDD A13 A17 NC D I/O8 NC VSS NC VSS I/O7 NC E NC I/O9 VSS CE VSS NC I/O6 F VDDQ NC VSS OE VSS I/O5 VDDQ G NC I/O10 BW2 ADV VSS NC I/O4 H I/O11 NC VSS GW VSS I/O3 NC J VDDQ VDD NC VDD NC VDD VDDQ K NC I/O12 VSS CLK VSS NC I/O2 L I/O13 NC VSS NC BW1 I/O1 NC M VDDQ I/O14 VSS BWE VSS NC VDDQ N I/O15 NC VSS A1 VSS I/O0 NC P NC I/OP2 VSS A0 VSS NC I/OP1 R NC A5 LBO VDD VSS A12 NC T NC A10 A15 NC A14 A11 ZZ(3) U VDDQ NC/TMS(2) NC/TDI(2) NC/TCK(2) NC/TDO(2) NC/TR ST(2,4) VDDQ 5280 drw 02d Top View , NOTES: 1. R5 does not have to be directly connected to VSS as long as the input voltage is < VIL. 2. These pins are NC for the "S" version or the JTAG signal listed for the "SA" version. Note: If NC, these pins can either be tied to VSS , VDD or left floating. 3. T7 can be left unconnected and the device will always remain in active mode. 4. TRST is offered as an optional JTAG Reset if required in the application. If not needed, can be left floating and will internally be pulled to V DD. 6.42 7 IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges Pin Configuration 128K x 36, 165 fBGA 1 2 3 4 5 6 7 8 9 10 11 A NC(4) A7 CE1 BW3 BW2 CS1 BWE ADSC ADV A8 NC B NC A6 CS0 BW4 BW1 CLK GW OE ADSP A9 NC(4) C I/OP3 NC VDDQ VSS VSS VSS VSS VSS VDDQ NC I/OP2 D I/O17 I/O16 VDDQ VDD VSS VSS VSS VDD VDDQ I/O15 I/O14 E I/O19 I/O18 VDDQ VDD VSS VSS VSS VDD VDDQ I/O13 I/O12 F I/O21 I/O20 VDDQ VDD VSS VSS VSS VDD VDDQ I/O11 I/O10 G I/O23 I/O22 VDDQ VDD VSS VSS VSS VDD VDDQ I/O9 I/O8 H VSS (1) NC NC VDD VSS VSS VSS VDD NC NC ZZ(3) J I/O25 I/O24 VDDQ VDD VSS VSS VSS VDD VDDQ I/O7 I/O6 K I/O27 I/O26 VDDQ VDD VSS VSS VSS VDD VDDQ I/O5 I/O4 L I/O29 I/O28 VDDQ VDD VSS VSS VSS VDD VDDQ I/O3 I/O2 M I/O31 I/O30 VDDQ VDD VSS VSS VSS VDD VDDQ I/O1 I/O0 N I/OP4 NC VDDQ VSS NC/TRST (2, 5) NC(4) NC (4) (2) VSS VDDQ NC I/OP1 (2) P NC NC A5 A2 NC/TDI A1 NC/TDO A10 A13 A14 NC(4) R LBO NC(4) A4 A3 NC/TMS(2) A0 NC/TCK(2) A11 A12 A15 A16 5280 tbl 17 Pin Configuration 256K x 18, 165 fBGA 1 2 3 4 5 6 7 8 9 10 11 A NC A7 CE1 BW2 NC CS1 BWE ADSC ADV A8 A10 B NC A6 CS0 NC BW1 CLK GW OE ADSP A9 NC(4) C NC NC VDDQ VSS VSS VSS VSS VSS VDDQ NC I/OP1 D NC I/O8 VDDQ VDD VSS VSS VSS VDD VDDQ NC I/O7 E NC I/O9 VDDQ VDD VSS VSS VSS VDD VDDQ NC I/O6 F NC I/O10 VDDQ VDD VSS VSS VSS VDD VDDQ NC I/O5 G NC I/O11 VDDQ VDD VSS VSS VSS VDD VDDQ NC I/O4 H VSS (1) NC NC VDD VSS VSS VSS VDD NC NC ZZ(3) J I/O12 NC VDDQ VDD VSS VSS VSS VDD VDDQ I/O3 NC K I/O13 NC VDDQ VDD VSS VSS VSS VDD VDDQ I/O2 NC L I/O14 NC VDDQ VDD VSS VSS VSS VDD VDDQ I/O1 NC M I/O15 NC VDDQ VDD VSS VSS VSS VDD VDDQ I/O0 NC VSS TRST (2, 5) N (4) I/OP2 NC (4) VDDQ NC/ (2) (4) NC NC VSS VDDQ NC NC (2) A11 A14 A15 NC(4) A12 A13 A16 A17 P NC NC A5 A2 NC/TDI A1 NC/TDO R LBO NC(4) A4 A3 NC/TMS(2) A0 NC/TCK (2) 5280 tbl 17a NOTES: 1. H1 does not have to be directly VSS as long as input voltage is < VIL 2. These pins are NC for the "S" version or the JTAG signal listed for the "SA" version. Note: If NC, these pins can either be tied to VSS , VDD or left floating. 3. H11 can be left unconnected and the device will always remain in active mode. 4. Pins P11, N6, B11, A1, R2 and P2 are reserved for 9M, 18M, 36M, 72M, 144M and 288M respectively. 5. TRST is offered as an optional JTAG Reset if required in the application. If not needed, can be left floating and will internally be pulled to VDD. 6.42 8 IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VDD = 3.3V ± 5%) Symbol Parameter Test Conditions Min. Max. Unit 5 µA |ILI| Input Leakage Current VDD = Max., VIN = 0V to V DD ___ |ILI| ZZ , LBO and JTAG Input Leakage Current (1) VDD = Max., VIN = 0V to V DD ___ 30 µA VOUT = 0V to V DDQ , Device Deselected ___ 5 µA IOL = +8mA, VDD = Min. ___ 0.4 V 2.4 ___ |ILO| Output Leakage Current Output Low Voltage VOL VOH Output High Voltage IOH = -8mA, VDD = Min. V 5280 tbl 08 NOTE: 1. The LBO, TMS, TDI, TCK and TRST pins will be internally pulled to VDD and the ZZ in will be internally pulled to VSS if they are not actively driven in the application. DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (1) 7.5ns Symbol Parameter Test Conditions 8ns 8.5ns Com'l Only Com'l Ind Com'l Ind Unit IDD Operating Power Supply Current Device Selected, Outputs Open, V DD = Max., VDDQ = Max., VIN > VIH or < VIL, f = fMAX(2) 255 200 210 180 190 mA ISB1 CMOS Standby Power Supply Current Device Deselected, Outputs Open, VDD = Max., VDDQ = Max., VIN > VHD or < VLD, f = 0(2,3) 30 30 35 30 35 mA ISB2 Clock Running Power Supply Current Device Deselected, Outputs Open, VDD = Max., VDDQ = Max., VIN > VHD or < VLD, f = fMAX (2,.3) 90 85 95 80 90 mA IZZ Full Sleep Mode Supply Current ZZ > VHD, VDD = Max. 30 30 35 30 35 NOTES: 1. All values are maximum guaranteed values. 2. At f = fMAX, inputs are cycling at the maximum frequency of read cycles of 1/tCYC while ADSC = LOW; f=0 means no input lines are changing. 3. For I/Os VHD = VDDQ - 0.2V, VLD = 0.2V. For other inputs VHD = VDD - 0.2V, VLD = 0.2V. AC Test Conditions AC Test Load (VDDQ = 3.3V) Input Pulse Levels 2ns Input Timing Reference Levels 1.5V Output Timing Reference Levels 1.5V AC Test Load VDDQ/2 50Ω 0 to 3V Input Rise/Fall Times mA 5280 tbl 09 I/O Z0 = 50Ω , 5280 drw 03 Figure 1. AC Test Load 6 See Figure 1 5280 tbl 10 5 4 ∆tCD 3 (Typical, ns) 2 1 20 30 50 80 100 Capacitance (pF) 200 5280 drw 05 Figure 2. Lumped Capacitive Load, Typical Derating 6.42 9 , IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges Synchronous Truth Table (1,3) Address Used CE CS 0 CS1 ADSP ADSC ADV GW BWE BWx OE(2) CLK I/O Deselected Cycle, Power Down None H X X X L X X X X X ↑ HI-Z Deselected Cycle, Power Down None L X H L X X X X X X ↑ HI-Z Deselected Cycle, Power Down None L L X L X X X X X X ↑ HI-Z Deselected Cycle, Power Down None L X H X L X X X X X ↑ HI-Z Deselected Cycle, Power Down None L L X X L X X X X X ↑ HI-Z Read Cycle, Begin Burst External L H L L X X X X X L ↑ DOUT Read Cycle, Begin Burst External L H L L X X X X X H ↑ HI-Z Read Cycle, Begin Burst External L H L H L X H H X L ↑ DOUT Read Cycle, Begin Burst External L H L H L X H L H L ↑ DOUT Read Cycle, Begin Burst External L H L H L X H L H H ↑ HI-Z Write Cycle, Begin Burst External L H L H L X H L L X ↑ DIN Write Cycle, Begin Burst External L H L H L X L X X X ↑ DIN Read Cycle, Continue Burst Next X X X H H L H H X L ↑ DOUT Read Cycle, Continue Burst Next X X X H H L H H X H ↑ HI-Z Read Cycle, Continue Burst Next X X X H H L H X H L ↑ DOUT Read Cycle, Continue Burst Next X X X H H L H X H H ↑ HI-Z Read Cycle, Continue Burst Next H X X X H L H H X L ↑ DOUT Read Cycle, Continue Burst Next H X X X H L H H X H ↑ HI-Z Read Cycle, Continue Burst Next H X X X H L H X H L ↑ DOUT Read Cycle, Continue Burst Next H X X X H L H X H H ↑ HI-Z Write Cycle, Continue Burst Next X X X H H L H L L X ↑ DIN Write Cycle, Continue Burst Next X X X H H L L X X X ↑ DIN Write Cycle, Continue Burst Next H X X X H L H L L X ↑ DIN Write Cycle, Continue Burst Next H X X X H L L X X X ↑ DIN Read Cycle, Suspend Burst Current X X X H H H H H X L ↑ DOUT Read Cycle, Suspend Burst Current X X X H H H H H X H ↑ HI-Z Read Cycle, Suspend Burst Current X X X H H H H X H L ↑ DOUT Read Cycle, Suspend Burst Current X X X H H H H X H H ↑ HI-Z Read Cycle, Suspend Burst Current H X X X H H H H X L ↑ DOUT Read Cycle, Suspend Burst Current H X X X H H H H X H ↑ HI-Z Read Cycle, Suspend Burst Current H X X X H H H X H L ↑ DOUT Read Cycle, Suspend Burst Current H X X X H H H X H H ↑ HI-Z Write Cycle, Suspend Burst Current X X X H H H H L L X ↑ DIN Write Cycle, Suspend Burst Current X X X H H H L X X X ↑ DIN Write Cycle, Suspend Burst Current H X X X H H H L L X ↑ DIN Write Cycle, Suspend Burst Current H X X X H H L X X X ↑ DIN Operation 5280 tbl 11 NOTES: 1. L = VIL, H = VIH, X = Don’t Care. 2. OE is an asynchronous input. 3. ZZ - low for the table. 6.42 10 IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges Synchronous Write Function Truth Table (1, 2) Operation GW BWE BW 1 BW 2 BW 3 BW 4 Read H H X X X X Read H L H H H H Write all Bytes L X X X X X Write all Bytes H L L L L L Write Byte 1(3) H L L H H H Write Byte 2(3) H L H L H H Write Byte 3(3) H L H H L H Write Byte 4(3) H L H H H L 5280 tbl 12 NOTES: 1. L = VIL, H = VIH, X = Don’t Care. 2. BW3 and BW4 are not applicable for the IDT71V3579. 3. Multiple bytes may be selected during the same cycle. Asynchronous Truth Table (1) Operation(2) OE ZZ I/O Status Power Read L L Data Out Active Read H L High-Z Active Write X L High-Z – Data In Active Deselected X L High-Z Standby Sleep Mode X H High-Z Sleep 5280 tbl 13 NOTES: 1. L = VIL, H = VIH, X = Don’t Care. 2. Synchronous function pins must be biased appropriately to satisfy operation requirements. Interleaved Burst Sequence Table ( LBO=V DD) Sequence 1 Sequence 2 Sequence 3 Sequence 4 A1 A0 A1 A0 A1 A0 A1 A0 First Address 0 0 0 1 1 0 1 1 Second Address 0 1 0 0 1 1 1 0 Third Address 1 0 1 1 0 0 0 1 Fourth Address(1) 1 1 1 0 0 1 0 0 5280 tbl 14 NOTE: 1. Upon completion of the Burst sequence the counter wraps around to its initial state. Linear Burst Sequence Table ( LBO=VSS) Sequence 1 Sequence 2 Sequence 3 Sequence 4 A1 A0 A1 A0 A1 A0 A1 A0 First Address 0 0 0 1 1 0 1 1 Second Address 0 1 1 0 1 1 0 0 Third Address 1 0 1 1 0 0 0 1 Fourth Address(1) 1 1 0 0 0 1 1 0 NOTE: 1. Upon completion of the Burst sequence the counter wraps around to its initial state. 6.42 11 5280 tbl 15 IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges AC Electrical Characteristics (VDD = 3.3V ±5%, Commercial and Industrial Temperature Ranges) 8ns 7.5ns(5) Symbol Parameter 8.5ns Min. Max. Min. Max. Min. Max. Unit 8.5 ____ 10 ____ 11.5 ____ ns Clock Parameter tCYC Clock Cycle Time tCH(1) Clock High Pulse Width 3 ____ 4 ____ 4.5 ____ ns tCL(1) Clock Low Pulse Width 3 ____ 4 ____ 4.5 ____ ns ____ 7.5 ____ 8 ____ 8.5 ns 2 ____ 2 ____ ns Output Parameters tCD Clock High to Valid Data tCDC Clock High to Data Change 2 ____ tCLZ(2) Clock High to Output Active 0 ____ 0 ____ 0 ____ ns tCHZ(2) Clock High to Data High-Z 2 3.5 2 3.5 2 3.5 ns tOE Output Enable Access Time ____ 3.5 ____ 3.5 ____ 3.5 ns tOLZ(2) Output Enable Low to Output Active 0 ____ 0 ____ 0 ____ ns tOHZ(2) Output Enable High to Output High-Z ____ 3.5 ____ 3.5 ____ 3.5 ns 1.5 ____ 2 ____ 2 ____ ns 2 ____ 2 ____ ns Set Up Times tSA Address Setup Time tSS Address Status Setup Time 1.5 ____ tSD Data In Setup Time 1.5 ____ 2 ____ 2 ____ ns tSW Write Setup Time 1.5 ____ 2 ____ 2 ____ ns 2 ____ 2 ____ ns tSAV Address Advance Setup Time 1.5 ____ tSC Chip Enable/Select Setup Time 1.5 ____ 2 ____ 2 ____ ns Hold Times tHA Address Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns tHS Address Status Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns 0.5 ____ 0.5 ____ 0.5 ____ ns 0.5 ____ 0.5 ____ ns 0.5 ____ 0.5 ____ ns 0.5 ____ ns 100 ____ ns ns ns tHD Data In Hold Time tHW Write Hold Time 0.5 ____ tHAV Address Advance Hold Time 0.5 ____ 0.5 ____ 0.5 ____ 100 ____ 100 ____ 100 ____ 100 ____ 40 ____ 50 ____ tHC Chip Enable/Select Hold Time Sleep Mode and Configuration Parameters tZZPW ZZ Pulse Width tZZR(3) ZZ Recovery Time 100 ____ tCFG(4) Configuration Set-up Time 34 ____ NOTES: 1. Measured as HIGH above VIH and LOW below VIL. 2. Transition is measured ±200mV from steady-state. 3. Device must be deselected when powered-up from sleep mode. 4. tCFG is the minimum time required to configure the device based on the LBO input. LBO is a static input and must not change during normal operation. 5. Commercial temperature range only. 6.42 12 5280 tbl 16 6.42 13 Output Disabled tSC tSA tSS tHS tOLZ tOE O1(Ax) tHC tHA Flow-through Read Ax tOHZ Ay (1) tCH tCD tSAV tHAV O1(Ay) tCDC tSW tCL O3(Ay) O4(Ay) (Burst wraps around to its initial state) ADV HIGH suspends burst Burst Flow-through Read O2(Ay) tHW O1(Ay) tCHZ O2(Ay) NOTES: 1. O1 (Ax) represents the first output from the external address Ax. O1 (Ay) represents the first output from the external address Ay; O2 (Ay) represents the next output data in the burst sequence of the base address Ay, etc. where A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. 2. ZZ input is LOW and LBO is Don't Care for this cycle. 3. CS0 timing transitions are identical but inverted to the CE and CS1 signals. For example, when CE and CS1 are LOW on this waveform, CS0 is HIGH. DATAOUT OE ADV (Note 3) CE, CS1 GW, BWE, BWx ADDRESS ADSC ADSP CLK tCYC 5280 drw 06 IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges Timing Waveform of Flow-Through Read Cycle (1,2) , 6.42 14 Ax (2) Single Read tSA tHA tSS tHS tCLZ tCD tOE O1(Ax) tOHZ tSW Ay tCH Write I1(Ay) tSD tHD tCL tHW Az tCD tOLZ O2(Az) O3(Az) Flow-through Burst Read O1(Az) tCDC 5280 drw 07 O4(Az) , NOTES: 1. Device is selected through entire cycle; CE and CS1 are LOW, CS0 is HIGH. 2. ZZ input is LOW and LBO is Don't Care for this cycle. 3. O1 (Ax) represents the first output from the external address Ax. I1 (Ay) represents the first input from the external address Ay; O1 (Az) represents the first output from the external address Az; O2 (Az) represents the next output data in the burst sequence of the base address Az, etc. where A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. DATAOUT DATAIN OE ADV GW ADDRESS ADSP CLK tCYC IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges Timing Waveform of Combined Flow-Through Read and Write Cycles (1,2,3) 6.42 15 DATAOUT DATAIN OE ADV (Note 3) CE, CS1 GW ADDRESS ADSC ADSP CLK tHC Ax O4(Aw) (1) Ay tCL tOHZ I1(Ax) I1(Ay) I2(Ay) (ADV suspends burst) tSAV GW is ignored when ADSP initiates a cycle and is sampled on the next cycle rising edge tCH I2(Ay) (2) I3(Ay) tHAV I4(Ay) tSD I1(Az) tHW tSW Az I2(Az) tHD 5280 drw 08 I3(Az) Timing Waveform of Write Cycle No. 1 - GW Controlled , NOTES: 1. ZZ input is LOW, BWE is HIGH and LBO is Don't Care for this cycle. 2. O4 (Aw) represents the final output data in the burst sequence of the base address Aw. I1 (Ax) represents the first input from the external address Ax. I1 (Ay) represents the first input from the external address Ay; I2 (Ay) represents the next input data in the burst sequence of the base address Ay, etc. where A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. In the case of input I2 (Ay) this data is valid for two cycles because ADV is high and has suspended the burst. 3. CS0 timing transitions are identical but inverted to the CE and CS1 signals. For example, when CE and CS1 are LOW on this waveform, CS0 is HIGH. O3(Aw) tSC tSA tHA tSS tHS tCYC IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges (1,2,3) 6.42 16 tHC Burst Read O3(Aw) tSC tSA tHA tSS tHS O4(Aw) Ax Ay tCL Single Write tOHZ I1(Ax) I1(Ay) Burst Write I2(Ay) (ADV HIGH suspends burst) I2(Ay) BWx is ignored when ADSP initiates a cycle and is sampled on the next clock rising edge BWE is ignored when ADSP initiates a cycle and is sampled on the next cycle rising edge tCH I3(Ay) I4(Ay) tSD Extended Burst Write I1(Az) tSAV tHW tSW tHW tSW Az I2(Az) tHD 5280 drw 09 I3(Az) Timing Waveform of Write Cycle No. 2 - Byte Controlled , NOTES: 1. ZZ input is LOW, GW is HIGH and LBO is Don't Care for this cycle. 2. O4 (Aw) represents the final output data in the burst sequence of the base address Aw. I1 (Ax) represents the first input from the external address Ax. I1 (Ay) represents the first input from the external address Ay; I2 (Ay) represents the next input data in the burst sequence of the base address Ay, etc. where A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. In the case of input I2 (Ay) this data is valid for two cycles because ADV is high and has suspended the burst. 3. CS0 timing transitions are identical but inverted to the CE and CS1 signals. For example, when CE and CS1 are LOW on this waveform, CS0 is HIGH. DATAOUT DATAIN OE ADV (Note 3) CE, CS1 BWx BWE ADDRESS ADSC ADSP CLK tCYC IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges (1,2,3) 6.42 17 tSS tSC tSA tHS tOLZ tOE Ax Single Read O1(Ax) tHC tHA tCH tCL tZZPW Snooze Mode tZZR NOTES: 1. Device must power up in deselected Mode. 2. LBO is Don't Care for this cycle. 3. It is not necessary to retain the state of the input registers throughout the Power-down cycle. 4. CS0 timing transitions are identical but inverted to the CE and CS1 signaals. For example, when CE and CS1 are LOW on this waveform, CS0 is HIGH. ZZ DATAOUT OE ADV (Note 4) CE, CS1 GW ADDRESS ADSC ADSP CLK tCYC Az 5280 drw 13 IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges Timing Waveform of Sleep (ZZ) and Power-Down Modes (1,2,3) , IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges Non-Burst Read Cycle Timing Waveform CLK ADSP ADSC ADDRESS Av Aw Ax Ay Az GW, BWE, BWx CE, CS1 CS0 OE (Av) DATAOUT (Aw) (Ax) (Ay) 5280 drw 10 NOTES: 1. ZZ input is LOW, ADV is HIGH and LBO is Don't Care for this cycle. 2. (Ax) represents the data for address Ax, etc. 3. For read cycles, ADSP and ADSC function identically and are therefore interchangable. , Non-Burst Write Cycle Timing Waveform CLK ADSP ADSC ADDRESS Av Aw Ax Ay Az (Ax) (Ay) (Az) GW CE, CS1 CS0 DATAIN (Av) (Aw) NOTES: 1. ZZ input is LOW, ADV and OE are HIGH, and LBO is Don't Care for this cycle. 2. (Ax) represents the data for address Ax, etc. 3. Although only GW writes are shown, the functionality of BWE and BWx together is the same as GW. 4. For write cycles, ADSP and ADSC have different limitations. 6.42 18 5280 drw 11 , IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges JTAG Interface Specification (SA Version only) tJF tJCL tJCYC tJR tJCH TCK Device Inputs(1)/ TDI/TMS tJS Device Outputs(2)/ TDO tJDC tJH tJRSR tJCD TRST(3) x M5280 drw 01 tJRST NOTES: 1. Device inputs = All device inputs except TDI, TMS and TRST. 2. Device outputs = All device outputs except TDO. 3. During power up, TRST could be driven low or not be used since the JTAG circuit resets automatically. TRST is an optional JTAG reset. JTAG AC Electrical Characteristics(1,2,3,4) Symbol Parameter Min. Max. Units ns Scan Register Sizes tJCYC JTAG Clock Input Period 100 ____ tJCH JTAG Clock HIGH 40 ____ ns tJCL JTAG Clock Low 40 ____ ns tJR JTAG Clock Rise Time ____ 5(1) ns tJF JTAG Clock Fall Time ____ 5(1) ns JTAG Identification (JIDR) tJRST JTAG Reset 50 ____ ns Boundary Scan (BSR) tJRSR JTAG Reset Recovery 50 ____ ns tJCD JTAG Data Output ____ 20 ns tJDC JTAG Data Output Hold 0 ____ ns tJS JTAG Setup 25 ____ ns 25 ____ ns tJH JTAG Hold Register Name Bit Size Instruction (IR) 4 Bypass (BYR) 1 32 Note (1) I5280 tbl 03 NOTE: 1. The Boundary Scan Descriptive Language (BSDL) file for this device is available by contacting your local IDT sales representative. I5280 tbl 01 NOTES: 1. Guaranteed by design. 2. AC Test Load (Fig. 1) on external output signals. 3. Refer to AC Test Conditions stated earlier in this document. 4. JTAG operations occur at one speed (10MHz). The base device may run at any speed specified in this datasheet. 6.42 19 IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges JTAG Identification Register Definitions (SA Version only) Instruction Field Value Revision Number (31:28) Description 0x2 IDT Device ID (27:12) 0x22C, 0x22E IDT JEDEC ID (11:1) 0x33 ID Register Indicator Bit (Bit 0) Reserved for version number. Defines IDT part number 71V3577SA and 71V3579SA, respectively. Allows unique identification of device vendor as IDT. 1 Indicates the presence of an ID register. I5280 tbl 02 Available JTAG Instructions Instruction Description OPCODE EXTEST Forces contents of the boundary scan cells onto the device outputs (1). Places the boundary scan register (BSR) between TDI and TDO. 0000 SAMPLE/PRELOAD Places the boundary scan register (BSR) between TDI and TDO. SAMPLE allows data from device inputs(2) and outputs(1) to be captured in the boundary scan cells and shifted serially through TDO. PRELOAD allows data to be input serially into the boundary scan cells via the TDI. 0001 DEVICE_ID Loads the JTAG ID register (JIDR) with the vendor ID code and places the register between TDI and TDO. 0010 HIGHZ Places the bypass register (BYR) between TDI and TDO. Forces all device o utput drivers to a High-Z state. 0011 RESERVED RESERVED RESERVED 0100 Several combinations are reserved. Do not use codes other than those identified for EXTEST, SAMPLE/PRELOAD, DEVICE_ID, HIGHZ, CLAMP, VALIDATE and BYPASS instructions. RESERVED CLAMP 0101 0110 0111 Uses BYR. Forces contents of the boundary scan cells onto the device outputs. Places the byp ass registe r (BYR) between TDI and TDO. RESERVED 1000 1001 RESERVED 1010 Same as above. RESERVED 1011 RESERVED 1100 VALIDATE Automatically loaded into the instruction register whenever the TAP controller passes through the CAPTURE-IR state. The lower two bits '01' are mand ated by the IEEE std. 1149.1 specification. 1101 RESERVED Same as above. 1110 BYPASS The BYPASS instruction is used to truncate the boundary scan register as a single bit in length. 1111 I5280 tbl 04 NOTES: 1. Device outputs = All device outputs except TDO. 2. Device inputs = All device inputs except TDI, TMS, and TRST. 6.42 20 IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges Ordering Information IDT XXX Device Type X S X XX Power Speed Package X X Process/ Temperature Range Blank I Commercial (0°C to +70°C) Industrial (-40°C to +85°C) G Restricted hazardous substance device PF** BG BQ 100-pin Plastic Thin Quad Flatpack (TQFP) 119 Ball Grid Array (BGA) 165 Fine Pitch Ball Grid Array (fBGA) 75* 80 85 Access Time in Tenths of Nanoseconds S SA Standard Power Standard Power with JTAG Interface Blank Y First Generation or current stepping Second Generation die step 71V3577 71V3579 , 128K x 36 Flow-Through Burst Synchronous SRAM with 3.3V I/O 256K x 18 Flow-Through Burst Synchronous SRAM with 3.3V I/O 5280 drw 12 *Commercial temperature range only. ** JTAG (SA version) is not available with 100 pin TQFP package Package Information 100-Pin Thin Quad Plastic Flatpack (TQFP) 119 Ball Grid Array (BGA) 165 Fine Pitch Ball Grid Array (fBGA) Information available on the IDT website 6.42 21 IDT71V3577, IDT71V3579, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with 3.3V I/O, Flow-Through Outputs, Burst Counter, Single Cycle Deselect Commercial and Industrial Temperature Ranges Datasheet Document History 7/23/99 9/17/99 12/31/99 04/03/00 Pg. 2 Pg. 3 Pg. 8 Pg. 18 Pg. 20 Pp. 1, 4, 8, 11, 19 Pg. 18 Pg. 4 06/01/00 07/15/00 Pg. 20 Pg. 7 Pg. 8 Pg. 20 10/25/00 04/22/03 06/30/03 Pg.8 Pg.4 Pg. 1,2,3,5-9 Pg. 5-8 Pg. 19,20 Pg. 21-23 Pg. 24 02/18/05 Pg. 21 Updated to new format Revised I/O pin description Revised block diagram for flow-through functionality Revised ISB1 and IZZ for speeds 7.5 to 8.5ns Added 119-lead BGA package diagram Added Datasheet Document History Added Industrial Temperature range offerings Added 100pinTQFP Package Diagram Outline Add capacitance table for BGA package; add Industrial temperature to table; Insert note to Absolute Max Ratings and Recommended Operating Temperature tables Add new package offering, 13 x 15mm 165 fBGA Correct 119BGA Package Diagram Outline Add note reference to BG119 pinout Add DNU reference note to BQ165 pinout Update BG119 Package Diagram Outline Dimensions Remove Preliminary status Add reference note to pin N5 on BQ165 pinout, reserved for JTAG TRST Updated 165 BGA table information from TBD to 7 Updated datasheet with JTAG information Removed note for NC pins (38,39(PF package); L4, U4 (BG package) H2, N7 (BQ package)) requiring NC or connection to Vss. Added two pages of JTAG Specification, AC Electrical, Definitions and Instructions Removed old package information from the datasheet Updated ordering information with JTAG and Y stepping information. Added information regarding packages available IDT website. Addedd "restricted hazardous substance device" to ordering information. CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com The IDT logo is a registered trademark of Integrated Device Technology, Inc. 6.42 22 for Tech Support: [email protected] 800-544-7726, x4033