IDTQS32245 HIGH-SPEED CMOS QUICKSWITCH 8-BIT BUS SWITCH INDUSTRIAL TEMPERATURE RANGE QUICKSWITCH® PRODUCTS HIGH-SPEED CMOS QUICKSWITCH 8-BIT BUS SWITCH DESCRIPTION: FEATURES: • • • • • • • • • IDTQS32245 The QS32245 provides a set of eight high-speed CMOS TTL-compatible bus switches in a pinout compatible with 74FCT245, 74F245, 74ALS/AS/ LS245 8-bit transceivers. The Output Enable (OE) signal turns the switches on similar to the OE signal of the 74’245. The QS32245 has 25Ω series resistors to reduce ground bounce noise. QuickSwitch devices provide an order of magnitude faster speed than conventional logic devices. The QS32245 is characterized for operation at -40°C to +85°C. Enhanced N channel FET with no inherent diode to Vcc Ω bidirectional switches connect inputs to outputs 5Ω Pin compatible with the 74F245, 74FCT245, and 74FCT245T Low power CMOS proprietary technology Zero propagation delay, zero ground bounce Undershoot clamp diodes on all switch and control inputs Ω resistors for low noise 25Ω TTL-compatible control inputs Available in SOIC, QSOP, and TSSOP packages APPLICATIONS: • • • • • • • Hot-swapping, hot-docking Voltage translation (5V to 3.3V) Power conservation Capacitance reduction and isolation Logic replacement (data processing) Clock gating Bus switching and isolation FUNCTIONAL BLOCK DIAGRAM A0 A1 A2 A3 A4 A5 A6 A7 B0 B1 B2 B3 B4 B5 B6 B7 OE The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE MARCH 2002 1 c 2002 Integrated Device Technology, Inc. DSC-5748/1 IDTQS32245 HIGH-SPEED CMOS QUICKSWITCH 8-BIT BUS SWITCH INDUSTRIAL TEMPERATURE RANGE PIN CONFIGURATION ABSOLUTE MAXIMUM RATINGS(1) NC 1 20 V CC A0 2 19 OE A1 3 18 B0 A2 4 17 B1 A3 5 16 B2 A4 6 15 B3 A5 7 14 B4 A6 8 13 B5 A7 9 12 B6 GND 10 11 B7 Symbol Description Max Unit VTERM(2) Supply Voltage to Ground –0.5 to +7 V VTERM(3) DC Switch Voltage Vs –0.5 to +7 V VTERM(3) DC Input Voltage VIN –0.5 to +7 V VAC AC Input Voltage (pulse width ≤ 20ns) –3 V IOUT DC Output Current 120 mA PMAX Maximum Power Dissipation (TA = 85°C) 0.5 W TSTG Storage Temperature –65 to +150 °C NOTE: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. Vcc terminals. 3. All terminals except Vcc. SOIC/ QSOP/ TSSOP TOP VIEW CAPACITANCE (TA = +25°C, f = 1.0MHZ, VIN = 0V, VOUT = 0V) Pins Typ. Max.(1) Unit Control Pins 3 5 pF 5 7 pF Quickswitch Channels (Switch OFF) NOTE: 1. This parameter is measured at characterization but not tested. PIN DESCRIPTION Pin Names Description OE Output Enable An Data I/Os Bn Data I/Os FUNCTION TABLE OE Outputs H Disconnected L An = Bn NOTE: 1. H = HIGH Voltage Level L = LOW Voltage Level 2 IDTQS32245 HIGH-SPEED CMOS QUICKSWITCH 8-BIT BUS SWITCH INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Industrial: TA = –40°C to +85°C, VCC = 5.0V ±5% Symbol Parameter Test Conditions VIH Input HIGH Level Guaranteed Logic HIGH for Control Pins VIL Input LOW Level Guaranteed Logic LOW for Control Pins IIN Input LeakageCurrent (Control Inputs)(2) 0V ≤ VIN ≤ VCC IOZ Off-State Output Current (Hi-Z) Switch ON Resistance RON(3) VP Pass Voltage(2) Min. Typ.(1) Max. Unit 2 — — V — — 0.8 V — — ±1 µA 0V ≤ VOUT ≤ VCC, Switches OFF — ±0.001 ±1 µA VCC = Min., VIN = 0V, ION = 30mA VCC = Min., VIN = 2.4V, ION =15mA VIN = VCC = 5V, IOUT = -5µA 18 18 3.7 23 25 4 35 40 4.2 Ω NOTES: 1. Typical values are at VCC = 5.0V, TA = 25°C. 2. Pass Voltage is guaranteed but not production tested. 3. ROUT changed on March 8, 2002. See rear page for more information. TYPICAL ON RESISTANCE vs VIN AT VCC = 5V 80 R ON (ohms) 70 60 50 40 30 20 10 0 0.0 0.5 1.0 1.5 2.0 V IN (Volts) 3 2.5 3.0 3.5 V IDTQS32245 HIGH-SPEED CMOS QUICKSWITCH 8-BIT BUS SWITCH INDUSTRIAL TEMPERATURE RANGE POWER SUPPLY CHARACTERISTICS Symbol Test Conditions(1) Parameter Max. Unit ICCQ Quiescent Power Supply Current VCC = Max., VIN = GND or Vcc, f = 0 3 µA ∆ICC Power Supply Current per Control Input HIGH (2) VCC = Max., VIN = 3.4V, f = 0 1.5 mA ICCD Dynamic Power Supply Current per MHz(3) VCC = Max., A and B pins open 0.25 mA/MHz Control Inputs Toggling at 50% Duty Cycle NOTES: 1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics. 2. Per TLL driven input (VIN = 3.4V, control inputs only). A and B pins do not contribute to ∆Icc. 3. This current applies to the control inputs only and represents the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant AC or DC currents as they transition. This parameter is guaranteed but not production tested. SWITCHING CHARACTERISTICS OVER OPERATING RANGE TA = -40°C to +85°C, VCC = 5.0V ± 5%; CLOAD = 50pF, RLOAD = 500Ω unless otherwise noted. Symbol Parameter tPLH Data Propagation Delay (2,3) tPHL An to/from Bn tPZL Switch Turn-on Delay tPZH OE to An/Bn tPLZ Switch Turn-off Delay (2) tPHZ OE to An/Bn Min. (1) Typ. Max. Unit — — 1.25 ns 0.5 — 6.6 ns 0.5 — 4.5 ns NOTES: 1. Minimums are guaranteed but not production tested. 2. This parameter is guaranteed but not production tested. 3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 1.25ns for CL = 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. 4 IDTQS32245 HIGH-SPEED CMOS QUICKSWITCH 8-BIT BUS SWITCH INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION IDTQS XXXXX Device Type XX Package X Process Blank Industrial (-40°C to +85°C) SO Q PA Small Outline IC Quarter Size Outline Package Thin Shrink Small Outline Package 32245 High Speed CMOS Quickswitch 8-Bit Bus Switch As per PCN L0201-02, the Output Resistance (RON) specifications have changed as of March 8, 2002. The original specifications were: Parameter RON Description Min. Typ. Max. Unit Ω VCC = Min, VIN = 0V, ION = 30mA 20 28 40 VCC = Min, VIN = 2.4V, ION = 15mA 20 35 48 CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com 5 for Tech Support: [email protected] (408) 654-6459