IH5009-5012, 5014, 5016-5020, 5022, 5024 CT T ODU CEMEN 7 R P Virtual Ground Analog Switch 4 E A T L LE 2-77 EP 4 O R 4 S D 0 OB NDE 1-80 m MME ications arris.co O C l E h p Features Description R @ p NO ntral A entapp c e C : l ai 20 Volts Peak-to-Peak all r Up • Switches Analog C Signals to The IH5009 series of analog switches were designed to fill o em May 1999 the need for an easy-to-use, inexpensive switch for both industrial and military applications. Although low cost is a primary design objective, performance and versatility have not been sacrificed. • Each Channel Complete - Interfaces with Most Integrated Logic • Switching Speeds Less Than 0.5µs • ID(OFF) Less Than 500pA Typical at 70oC Each package contains up to four channels of analog gating and is designed to eliminate the need for an external driver. The odd numbered devices are designed to be driven directly from TTL open collector logic (15 volts) while the even numbered devices are driven directly from low level TTL logic (5 volts). Each channel simulates a SPDT switch. SPST switch action is obtained by leaving the diode cathode unconnected; for SPDT action, the cathode should be grounded (0V). The parts are intended for high performance multiplexing and commutating usage. A logic “0” turns the channel ON and a logic “1” turns the channel OFF. • Effective rDS(ON) - 5Ω to 50Ω • Commercial and Military Temperature Range Operation Part Number Information PART NUMBER CHANNELS LOGIC LEVEL IH5009 4 +15 DD, PD IH5010 4 +5 DD, PD IH5011 4 +15 DE, PE IH5012 4 +5 DE, PE IH5014 3 +5 DD, PD IH5016 3 +5 DE, PE IH5017 2 +15 PA M = MILITARY (-55oC to 125oC) IH5018 2 +5 DD, PA C = COMMERCIAL (0oC to 70oC) IH5019 2 +15 DE, PA IH5020 2 +5 DE, PA IH5022 1 +5 DD, PA IH5024 1 +5 PA PACKAGE PKG NO. IH50XX M DE PACKAGE PA - 8 LEAD PDIP PD - 14 LEAD PDIP PE - 16 LEAD PDIP DD - 14 LEAD CERDIP DE - 16 LEAD CERDIP TEMPERATURE RANGE BASIC PART NUMBER NOTE: Mil-Temperature range (-55oC to 125oC) available in ceramic packages only. CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright © Harris Corporation 1999 4-1 File Number 3129.1 IH5009 Series Functional Diagrams (Numbers in brackets refer to CERDIP Packages) IH5009, IH5010 (14 LEAD CERDIP, 14 LEAD PDIP) IH5011, IH5012 (16 LEAD CERDIP, 16 LEAD PDIP) IH5014 (14 LEAD CERDIP, 14 LEAD PDIP) IH5016 (16 LEAD CERDIP, 16 LEAD PDIP) IH5017 (8 LEAD PDIP) IH5018 (8 LEAD PDIP, 14 LEAD CERDIP) IH5019, IH5020 (8 LEAD PDIP, 16 LEAD CERDIP) IH5022 (8 LEAD PDIP, 14 LEAD CERDIP) IH5024 (8 LEAD PDIP) 4-2 IH5009 Series Absolute Maximum Ratings Thermal Information Positive Analog Signal Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 30V Negative Analog Signal Voltage . . . . . . . . . . . . . . . . . . . . . . . . .-15V Diode Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10mA Power Dissipation (Note) . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mW Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC Operating Conditions Temperature Range 5009C Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0oC to 70oC 5009M Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: Dissipation rating assumes device is mounted with all leads welded or soldered to printed circuit board in ambient temperature below 75oC. For higher temperature, derate at rate of 5m/WoC. Electrical Specifications PARAMETER (Per Channel) (NOTE 1) SYMBOL (NOTE 4) TEST CONDITIONS (NOTE 2) TYPE -55oC (M) 0oC (C) MIN/MAX 25oC TYP MIN/MAX 125oC(M) 70oC (C) MIN/MAX UNITS Input Current-ON IIN(ON) ALL VIN = 0V, ID = 2mA - 0.01 ±0.5 100 µA Input Current-OFF IIN(OFF) 5V Logic Ckts VIN = +4.5V, VA = ±10V - 0.04 ±0.5 20 nA Input Current-OFF IIN(OFF) 15V Logic Ckts VIN = +11V, VA = ±10V - 0.04 ±0.5 20 nA Channel Control Voltage-ON VIN(ON) 5V Logic Ckts Note 3 0.5 - 0.5 0.5 V Channel Control Voltage-ON VIN(ON) 15V Logic Ckts Note 3 1.5 - 1.5 1.5 V Channel Control Voltage-OFF VIN(OFF) 5V Logic Ckts Note 3 - - 4.5 4.5 V Channel Control Voltage-OFF VIN(OFF) 15V Logic Ckts Note 3 - - 11.0 11.0 V Leakage Current-OFF ID(OFF) 5V Logic Ckts VIN = +4.5V, VA = ±10V - 0.02 ±0.5 20 nA Leakage Current-OFF ID(OFF) 15V Logic Ckts VIN = +11V, VA = ±10V - 0.02 ±0.5 20 nA Leakage Current-ON ID(ON) 5V Logic Ckts VIN = 0V, IS = 1mA - 0.30 ±1.0 1000 (M) 200 (C) nA Leakage Current-ON ID(ON) 15V Logic Ckts VIN = 0V, IS = 1mA - 0.10 ±0.5 500 (M) 100 (C) nA Leakage Current-ON ID(ON) 5V Logic Ckts VIN = 0V, IS = 2mA - - 1.0 10 µA Leakage Current-ON ID(ON) 15V Logic Ckts VIN = 0V, IS = 2mA - - 2.0 100 µA Drain-Source ON-Resistance rDS(ON) 5V Logic Ckts ID = 2mA, VIN = 0.5V 150 90 150 385 (M) 240 (C) Ω Drain-Source ON-Resistance rDS(ON) 15V Logic Ckts ID = 2mA, VIN = 1.5V 100 80 100 250 (M) 160 (C) Ω Turn-ON Time t(ON) All - 150 500 - ns Turn-OFF Time t(OFF) All - 300 500 - ns Cross Talk CT All - 120 - - dB f = 100Hz NOTES: 1. (OFF) and (ON) subscript notation refers to the conduction state of the FET switch for the given test. 2. Refer to Figure 1 for definition of terms. 3. VIN(ON) and VIN(OFF) are test conditions guaranteed by the tests of rDS(ON) and ID(OFF) respectively. 4. “5V Logic CKTS” applies to even-numbered devices. “15V Logic CKTS” applies to odd-numbered devices. 4-3