Corporate: www.cdtechno.com Product: www.cdpowerelectronics.com IHB100S 100 Watt Single Output Half Brick DC/DC Converter 33 - 75V Input Range 1500VDC Isolation Between Input and Output High Efficiency: 86% Typical Operation to 100°C Baseplate Temperature 50µS Transient Recovery, 0-90% Load Step Primary & Secondary Remote On/Off External Synchronization IHB100S Series Are Approved to UL/CUL 1950, EN 60950 The IHB100S series standard half brick modules are designed for today’s demanding industrial applications. Available in two wide range inputs, these isolated converters offer many features in the standard models. With a complement of safety agency approvals and low noise operations, the converters respond extremely fast to change in load conditions. Inherent in the design are very well-controlled output voltage and no need for minimum loading. PRODUCT SELECTION CHART INPUT VOLTAGE (V DC ) 48 (33-75) 48 (33-75) IHB100S4803 IHB100S4805 ABSOLUTE MAX. RATINGS Output Short-Circuit Duration Continuous Baseplate Temperature +100°C Lead Temperature (soldering, 10 seconds max) +300°C Storage Temperature +125°C Input to Output Isolation 1500 VDC RATED VOUT (VDC) RATED MAXIMUM I OUT (A) 3.3 5.1 30 20 EFFICIENCY vs TEMPERATURE TCASE = +40°C, nominal input voltage, nominal load, recommended external components applied, unless otherwise specified.* Change in Efficiency (%) MODEL Case Temperature (°C) SPECIFICATIONS, ALL MODELS Specifications are at TCASE = +40°C nominal input voltage unless otherwise specified. INPUT PARAMETER Voltage Range Reflected Ripple Current Input Ripple Rejection Maximum Input Current No Load Power Dissipation Inrush Charge Quiescent Operating Current Primary On/Off Disabled Secondary On/Off Disabled PARAMETER GENERAL ISOLATION Input to Output Input to Baseplate Resistance, Input - Output Capacitance, Input - Output Leakage Current GENERAL Set Point Accuracy Turn-on Time Remote On/Off Control Inputs Primary Sink Current-Logic Low Vlow Vhigh Secondary Sink Current-Logic Low Vlow Vhigh External Synchronization Input Frequency Pulse Width Source Impedence Input High Voltage Input Low Voltage Input Impedance Switching Frequency Weight TEMPERATURE Operation/Specification Storage Shutdown Thermal Inpedance CONDITIONS MIN TYP MAX UNITS 33 48 75 370 50 60 VDC mA dB 5 6 0.247 A W mC 10 20 mA mA Peak - Peak DC to 1KHz Output Power = 100W VIN = 30V POUT = 0, VIN, Min<VIN<VIN, Max 7.5 15 CONDITIONS MIN Peak Test 1500 1500 10 TYP VISO = 240VAC, 60Hz 2000 180 VIN = Nominal, IO=INOM Within 1% of Nominal VOUT 3.5 Open Collector/Drain VIN = VMAX MAX UNITS VDC VDC MΩ pF µA, rms 1 5 % mSec 7 0.8 Open Collector mA V 100 0.4 Open Collector µA V 520 320 47 5 1 KHz nSec Ω V V Ω KHz oz (g) Open Collector/Drain 440 150 4 0 470 470 480 490 3 (85) Case Temperature -40 -55 +100 Case to Ambient +100 +125 +115 8.2 °C °C °C °C/W * See Application Notes available on the web at www.cdpowerelectronics.com Corporate: www.cdtechno.com IHB100S REV A 10/01 2 IHB100S4803 OUTPUT PARAMETER Output Power Set Point Voltage Output Current, IOUT Output Ripple, p-p Output Adjust Range Output Temperature Drift Line Regulation Load Regulation Current Limit Inception Short-Circuit Current Transient Response Peak Deviation Settling Time Overvoltage Limit Efficiency IHB100S4805 OUTPUT PARAMETER * Output Power Set Point Voltage Output Current, IOUT Output Ripple, p-p Output Adjust Range Output Temperature Drift Line Regulation Load Regulation Current Limit Inception Short-Circuit Current Transient Response Peak Deviation Settling Time Overvoltage Limit Efficiency VOUT CONDITIONS Min 100 Watts Max IO Nom 0 DC to 20MHz* * Nom 50 3.3 15 100 3.15 .02 VIN, Min≤VIN≤VIN, Max IO = IO, Nom Min Load to Rated Load Max 100 30.0 200 3.80 .05 0.05 0.50 38 30 0.10 1.00 150 35 250 50 5.0 38 UNITS W V A mV V %/°C % % A A 50 to 100% Load Step VOUT, 1% of VOUT, Nom 4.2 83 VIN=NOM, IO=30A 84 mV µSec V % VOUT CONDITIONS Min 100 Watts Maximum IO Nom 0 DC to 20MHz* * Nom 50 5.1 10 100 4.60 .02 VIN, Min≤VIN≤VIN, Max IO = IO, Nom Min Load to Rated Load Max 100 20 150 5.50 .05 0.05 0.5 26.0 20.0 0.10 1.0 200 35 300 50 7.0 26.0 UNITS W V A mV V %/°C % % A A 50 to 100% Load Step VOUT, 1% of VOUT, Nom 6.0 86 VIN=NOM, IO=20A 87 mV µSec V % See Application Notes available on the web at www.cdpowerelectronics.com Product: www.cdpowerelectronics.com IHB100S REV A 10/01 3 MECHANICAL SIDE VIEW PIN SIDE DOWN PIN CONNECTIONS 1 2 3 4 5 6 7 8 PIN SIDE UP PRIMARY ON/OFF -VIN +VIN SYNC IN TRIM +V OUT -V OUT SECONDARY ON/OFF NOTES: All dimensions are in inches (millimeters). PIN PLACEMENT TOLERANCE: ± 0.005" MECHANICAL TOLERANCE: ± 0.015" Marked with: specific model ordered, date code, job code. MATERIAL: Units are encapsulated in a low thermal resistance molding compound which has excellent chemical resistance and electrical properties in high humidity environments and over a wide operating temperature range. The encapsulant and outer shell of the unit have UL94V-0 ratings. Lead material is solder plated to allow ease of solderability. C&D Technologies (Power Electronics) Ltd. Shannon, Co. Clare, Ireland Tel: +353.61.474.133 Fax:+353.61.474.141 Power Electronics Division, United States 3400 E Britannia Drive, Tucson, Arizona 85706 Tel: 800.547.2537 Fax: 520.770.9369 C&D Technologies, (NCL) Milton Keynes MK14 5BU UK Tel: +44 (0)1908 615232 Fax: +44 (0)1908 617545 Any data, prices, descriptions or specifications presented herein are subject to revision by C&D Technologies, Inc. without notice. While such information is believed to be accurate as indicated herein, C&D Technologies, Inc. makes no warranty and hereby disclaims all warranties, express or implied, with regard to the accuracy or completeness of such information. Further, because the product(s) featured herein may be used under conditions beyond its control, C&D Technologies, Inc. hereby disclaims all warranties, either express or implied, concerning the fitness or suitability of such product(s) for any particular use or in any specific application or arising from any course of dealing or usage of trade. The user is solely responsible for determining the suitability of the product(s) featured herein for user’s intended purpose and in user’s specific application. C&D Technologies, Inc. does not warrant or recommend that any of its products be used in any life support or aviation or aerospace applications. Corporate: www.cdtechno.com IHB100S REV A 10/01 4