IL440 VISHAY Vishay Semiconductors Optocoupler, Phototriac Output, Low Input Current Features • • • • • 400 and 600 V Blocking Voltage 5.0 mA Maximum Trigger Current Isolation Test Voltage, 5300 VRMS, t = 1.0 sec. Isolation Materials per UL94 Pin Compatible with Optocouplers IL440-1 MOC 3051 IL440-2 MOC 3052 IL440-3 MOC3053 IL440-4 MOC 3021 IL440-5 MOC 3022 IL440-6 MOC 3023 • Lead-free component • Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC Agency Approvals • UL1577, File No. E52744 System Code H or J, Double Protection • CSA 93751 • DIN EN 60747-5-2 (VDE0884) DIN EN 60747-5-5 pending Available with Option 1 • BABT/ BSI IEC60950 IEC60065 Applications High Current Triac Driver Solid State Relay Switch Small AC Loads Document Number 83631 Rev. 1.5, 26-Oct-04 6 MT2 C 2 5 NC NC 3 4 MT1 e3 i179035 Pb Pb-free Order Information Part Remarks IL440-1 15 mA IFT, 600 V VDRM, DIP-6 IL440-2 10 mA IFT, 600 V VDRM, DIP-6 IL440-3 5.0 mA IFT, 600 V VDRM, DIP-6 IL440-4 15 mA IFT, 400 V VDRM, DIP-6 IL440-5 10 mA IFT, 400 V VDRM, DIP-6 IL440-6 5.0 mA IFT, 400 V VDRM, DIP-6 IL440-1X009 15 mA IFT, 600 V VDRM, SMD-6 (option 9) IL440-2X006 10 mA IFT, 600 V VDRM, DIP-6 400 mil (option 6) IL440-3X007 5.0 mA IFT, 600 V VDRM, SMD-6 (option 7) IL440-3X009 5.0 mA IFT, 600 V VDRM, SMD-6 (option 9) IL440-4X007 15 mA IFT, 400 V VDRM, SMD-6 (option 7) IL440-4X009 15 mA IFT, 400 V VDRM, SMD-6 (option 9) IL440-5X006 10 mA IFT, 400 V VDRM, DIP-6 400 mil (option 6) IL440-5X009 10 mA IFT, 400 V VDRM, SMD-6 (option 9) IL440-6X006 5.0 mA IFT, 400 V VDRM, DIP-6 400 mil (option 6) IL440-6X007 5.0 mA IFT, 400 V VDRM, SMD-6 (option 7) IL440-6X009 5.0 mA IFT, 400 V VDRM, SMD-6 (option 9) Description The IL440 consists of a GaAs infrared emitter optically coupled to a silicon planar triac chip with a nonzero crossing network. The two semiconductors are assembled in a 6 pin dual-in-line plastic package. The output detector IL440-1, 2, 3 is capable of blocking up to 600 volts which permits control of off-line voltages up to 240 VAC. The IL440 can handle currents up to 100 mA RMS. A 1 For additional information on the available options refer to Option Information. www.vishay.com 1 IL440 VISHAY Vishay Semiconductors Absolute Maximum Ratings Tamb = 25 °C, unless otherwise specified Stresses in excess of the absolute Maximum Ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute Maximum Rating for extended periods of the time can adversely affect reliability. Input Symbol Value Reverse voltage Parameter VR 5.0 V Forward current IF 60 mA Surge current Test condition P.W. < 10 µs Power dissipation Junction temperature Unit IFSM 3.0 A Pdiss 100 mW Tj 100 °C Output Parameter Test condition Peak off-state voltage Part Symbol Value Unit IL440-1 VDRM 600 V IL440-2 VDRM 600 V IL440-3 VDRM 600 V IL440-4 VDRM 400 V IL440-5 VDRM 400 V IL440-6 VDRM 400 V On-state RMS current ID(RMS) 100 mA Peak surge current tp ≤ 10 ms IFSM 1.2 A Peak on-state current tp/T = 0.01 ≤ 100 µs IDRM 2.0 A Pdiss 300 mW Tj 125 °C Power dissipation Junction temperature Coupler Parameter Test condition Isolation voltage, 1.0 sec., per Standard Climate 23 °C/50 % RH, DIN 50014 Symbol Value Unit VISO 5300 VRMS Creepage ≥ 7.0 mm Clearance ≥ 7.0 mm Isolation resistance VIO = 500 V, Tamb = 25 °C RIO ≥ 1012 Ω VIO = 500 V, Tamb = 100 °C RIO ≥ 10 Ω 11 Total power dissipation Ptot 330 mW Storage temperature range Tstg - 55 to + 125 °C Ambient temperature Tamb - 40 to + 100 °C Tj 100 °C Tsld 260 °C Junction temperature Lead soldering temperature www.vishay.com 2 2.0 mm from case, t < 10 s Document Number 83631 Rev. 1.5, 26-Oct-04 IL440 VISHAY Vishay Semiconductors Electrical Characteristics Tamb = 25 °C, unless otherwise specified Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. Input Parameter Test condition Symbol Forward voltage IF = 50 mA VF Reverse voltage IR = 10 µA VR Junction capacitance VR = 0 V, f = 1.0 MHz Cj Min Typ. Max 1.25 Unit V 5.0 V 50 pF Output Off- state output terminal voltage (see Table 1.) Parameter Test condition Typ. Max Unit VTM 1.5 3.0 V IF = 0, VS = 240 VRMS dVcr/dt 50 V/µs IF = 30 mA, VS = 60 VRMS dVcrq/dt 0.25 V/µs Peak on-state voltage ITM = 100 mA, IFT = 30 mA Critical rate of rise of off-state voltage Symbol Min 0.13 IFT and Blocking Voltage Selection1) 1) Bin number BV (Volts) Max @ IDRM = 500 nA IFT Max @ VT = 6 V, RL=150 Ω IL440-1 600 15 IL440-2 600 10 IL440-3 600 5.0 IL440-4 400 15 IL440-5 400 10 IL440-6 400 5.0 Test voltage must be applied within dV/dt rating of 0.13 V/µsec. Coupler Parameter Holding current Test condition IF ≥ 10 mA, VS ≥ 3.0 V Symbol Min IH Typ. Max 1.0 Unit mA Maximum Safety Ratings (according to DIN EN 60747-5-2(VDE0884)/ DIN EN 60747-5-5 pending) see figure 1 This optocoupler is suitable for safe electrical isolation only within the safety ratings. Compliance with the safety ratings shall be ensured by means of suitable protective circuits. Input The device is used for protective separation agains electrical shock within the maximum safety ratings. This must be ensured by protective circuits in the applications. Parameter Test condition Forward voltage Symbol Min Typ. IS, INPUT Max Unit 130 mA Max Unit 300 mW Output Parameter Power dissipation Document Number 83631 Rev. 1.5, 26-Oct-04 Test condition Symbol PS, OUTPUT Min Typ. www.vishay.com 3 IL440 VISHAY Vishay Semiconductors Package Dimensions in Inches (mm) 3 2 1 4 5 6 pin one ID .248 (6.30) .256 (6.50) ISO Method A .335 (8.50) .343 (8.70) .300 (7.62) typ. .048 (0.45) .022 (0.55) .039 (1.00) Min. .130 (3.30) .150 (3.81) 18° 4° typ. .031 (0.80) min. .031 (0.80) .035 (0.90) .018 (0.45) .022 (0.55) .100 (2.54) typ. 3°–9° .114 (2.90) .130 (3.0) .010 (.25) typ. .300–.347 (7.62–8.81) i178004 Option 6 Option 7 .407 (10.36) .391 (9.96) .307 (7.8) .291 (7.4) .300 (7.62) TYP. Option 9 .375 (9.53) .395 (10.03) .300 (7.62) ref. .028 (0.7) MIN. .180 (4.6) .160 (4.1) .0040 (.102) .0098 (.249) .315 (8.0) MIN. .014 (0.35) .010 (0.25) .400 (10.16) .430 (10.92) www.vishay.com 4 .331 (8.4) MIN. .406 (10.3) MAX. .012 (.30) typ. .020 (.51) .040 (1.02) .315 (8.00) min. 15° max. 18450 Document Number 83631 Rev. 1.5, 26-Oct-04 IL440 VISHAY Vishay Semiconductors Ozone Depleting Substances Policy Statement It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operatingsystems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Telephone: 49 (0)7131 67 2831, Fax number: 49 (0)7131 67 2423 Document Number 83631 Rev. 1.5, 26-Oct-04 www.vishay.com 5