Fairchild ILC7083 150ma sot-23 low noise cmos rf-ldoâ ¢ regulator Datasheet

www.fairchildsemi.com
ILC7083/ILC7084
150mA SOT-23 Low Noise CMOS RF-LDO™
Regulator
Features
Description
•
•
•
•
The ILC7083/ILC7084 is a 150mA low dropout (LDO)
voltage regulator designed to provide a high performance
solution to low power systems. The device offers a typical
combination of low dropout and low quiescent current
expected of CMOS parts, while uniquely providing the low
noise and high ripple rejection characteristics usually only
associated with bipolar LDO regulators.
•
•
•
•
•
•
•
•
Ultra low 1mV dropout per 1mA load
3% output voltage accuracy
Only 40µVRMS noise
Uses low ESR ceramic output capacitor to minimize noise
and output ripple
Only 100µA ground current at 100mA load
Ripple rejection up to 85dB at 1kHz, 60dB at 1MHz
Excellent line and load transient response
Over current / over temperature protection
Guaranteed to 150mA output current
Industry standard five lead SOT-23 package
Fixed 2.5V, 2.7V, 2.85V, 3.0V, 3.3V, 3.6V, 5V output
voltage for ILC7083 and adjustable output voltage for
ILC7083/ILC7084
Metal mask option available for custom voltages between
2.5V and 5.1V
The ILC7083/ILC7084 is designed to make use of low cost
ceramic capacitors while outperforming other devices that
require tantalum capacitors.
As opposed to ILC7084, the ILC7083 has a built in output
capacitor discharge circuit active in shutdown mode. This
feature is necessary in applications where the output voltage
must decrease quickly to zero volt in shutdown mode.
Applications
•
•
•
•
The device has been optimized to meet the needs of modern
wireless communications design; Low noise, low dropout,
small size, high peak current, high noise immunity.
Cellular phones
Wireless communicators
PDAs / palmtops / organizers
Battery powered portable electronics
Typical Applications
VOUT
5
COUT
SOT-23-5
4
CNOISE
ILC7083
1
2
3
VIN
ON
CIN
OFF
REV. 1.0.9 1/28/03
ILC7083/ILC7084
Pin Assignments
Fixed Voltage Option
GND
ON/OFF
8
1
7
2
CNOISE
VOUT
CNOISE
VOUT
VADJ
5
4
5
4
N/C
ILC7083-xx
VIN
VOUT
1
VIN
5
4
ILC7083ADJ
or ILC7084ADJ
ILC7083-xx
6
3
Adjustable Voltage Option
VOUT
VIN
2
3
GND ON/OFF
1
VIN
SOT-23-5
SOIC-8
2
GND
1
ON/OFF
2
8
VADJ
7
N/C
ILC7083ADJ
VIN
3
6
VOUT
VIN
4
5
VOUT
3
GND ON/OFF
SOT-23-5
SOIC-8
Pin Description ILC7083-xx (Fixed voltage version)
Pin Number
SOIC-8 SOT-23-5 Pin Name
3 and 4
1
VIN
1
2
GND
Pin Description
Connect directly to supply
Ground pin. Local ground for CNOISE and COUT.
By applying less than 0.6V to this pin the device will be turned off.
2
3
ON/OFF
8
4
CNOISE
5 and 6
5
VOUT
Output Voltage. Connect COUT between this pin and GND.
7
–
N/C
Not Connected
Optional noise bypass capacitor may be connected between this pin and
GND. Do not connect CNOISE directly to the main power ground plane.
Pin Description ILC7083-ADJ (Adjustable voltage version)
Pin Number
SOIC-8 SOT-23-5 Pin Name
2
Pin Description
Connect directly to supply
3 and 4
1
VIN
1
2
GND
2
3
ON/OFF
8
4
VADJ
Voltage feedback pin to set the adjustable output voltage. Do not connect a
capacitor to this pin.
5 and 6
5
VOUT
Output Voltage. Connect COUT between this pin and GND.
7
–
N/C
Not Connected
Ground pin. Local ground for CNOISE and COUT.
By applying less than 0.6V to this pin the device will be turned off.
REV. 1.0.9 1/28/03
ILC7083/ILC7084
Internal Block Diagram
VIN
INTERNAL VDD
CNOISE
BANDGAP
REFERENCE
VREFD
TRANSCONDUCTANCE
AMPLIFIER
ERROR
AMPLIFIER
VOUT
FEEDBACK
GND
ON/OFF
Absolute Maximum Ratings
Parameter
Symbol
Ratings
Units
VIN
V
VON/OFF
-0.3 to +13.5
-0.3 to VIN
Output Current
IOUT
Short circuit protected
mA
Output Voltage
VOUT
-0.3 to VIN + 0.3
V
Input Voltage
On/Off Input Voltage
Package Power Dissipation (SOT-23-5)
Maximum Junction Temp Range
Storage Temperature
Package Thermal Resistance
PD
250 (Internally Limited)
mW
TJ(max)
-40 to +150
°C
TSTG
-40 to +125
°C
θJA
333
°C/W
Recommended Operating Conditions
Parameter
Input Voltage
Operating Ambient Temperature
REV. 1.0.9 1/28/03
Min.
Typ.
Max.
Units
VOUT + VDO
VOUT + 1
13
V
+85
°C
–40
3
ILC7083/ILC7084
Electrical Characteristics ILC7083/ILC7084
Unless otherwise specified, all limits are at TA=25°C; VIN = VOUT(NOM) +1V, IOUT = 1mA, COUT = 1µF, VON/OFF = 2V.
Boldface type denotes specifications which apply over the specified operating temperature range.
Parameter
Input Voltage Range
Output Voltage
Feedback Voltage
(ADJ version)
Line Regulation
Dropout Voltage
(Note 3)
Ground Pin Current
Shutdown (OFF) Current
ON/OFF Input Voltage
Symbol
VIN
VOUT
Conditions
1mA < IOUT < 150mA
1mA < IOUT < 150mA
VADJ
∆VOUT/
(VOUT*∆VIN)
VIN – VOUT
IGND
ION/OFF
VON/OFF
ON/OFF Pin Input
Current
Peak Output Current
(Note 4)
Output Noise Voltage (RMS)
IIN( ON/OFF)
Ripple Rejection
∆VOUT/∆VIN
Dynamic Line Regulation
∆VOUT(line)
Dynamic Load Regulation
Short Circuit Current
∆VOUT(load)
ISC
IOUT(peak)
eN
Min
2
-3
-4
1.217
1.204
VOUT(NOM) +1V < VIN < 12V
Typ
VOUT(NOM)
VOUT(NOM)
1.255
0.007
IOUT= 0mA (Note 4)
0.1
IOUT = 10mA
10
IOUT = 50mA
50
IOUT = 100mA
100
IOUT = 150mA
150
IOUT = 0mA
95
IOUT = 10mA
100
IOUT = 50mA
100
IOUT = 100mA
100
IOUT = 150mA
115
VON/OFF = 0V
High = Regulator On
Low = Regulator Off
VON/OFF = 0.6V, regulator OFF
VON/OFF = 2V, regulator ON
VOUT > 0.95VOUT(NOM),
tpw = 2ms
BW = 300Hz to 50kHz, CIN = 1µF
CNOISE = 0.01µF, COUT = 2.2µF,
IOUT = 10mA
Freq. = 1kHz
COUT = 4.7µF,
IOUT = 100mA
Freq. = 10kHz
Freq. = 1MHz
VIN: VOUT(NOM) + 1V to
VOUT(NOM) + 2V,
tr/tf = 2µs; IOUT = 150mA
IOUT: 1mA to 150mA; tr < 5µS
VOUT = 0V
0.1
Max
13
+3
+4
1.292
1.305
0.014
0.032
1
2
25
35
75
100
150
200
225
300
200
220
220
240
220
240
240
260
260
280
2
Units
V
%VOUT
(NOM)
V
%/V
mV
µA
µA
1.5
0.6
400
0.3
1
500
µA
mA
40
µVRMS
85
70
60
14
dB
mV
40
600
mV
mA
Notes:
1. Absolute maximum ratings indicate limits which when exceeded may result in damage to the component. Electrical specifications do not apply
when operating the device outside of its rated operating conditions.
2. Specified Min/Max limits are production tested or guaranteed through correlation based on statistical control methods.
Measurements are taken at constant junction temperature as close to ambient as possible using low duty pulse testing.
3. Dropout voltage is defined as the input to output differential voltage at which the output voltage drops 2% below the nominal value measured
with an IV differential.
4. Guaranteed by design.
4
REV. 1.0.9 1/28/03
ILC7083/ILC7084
Operation
REV. 1.0.9 1/28/03
DOMINANT POLE
85 dB
OUTPUT POLE
GAIN
The ILC7083/ILC7084 LDO design is based on an advanced
circuit configuration for which patent protection has been
applied. Typically it is very difficult to drive a capacitive output with an amplifier. The output capacitance produces a
pole in the feedback path, which upsets the carefully tailored
dominant pole of the internal amplifier. Traditionally the
pole of the output capacitor has been “eliminated” by reducing the output impedance of the regulator such that the pole
of the output capacitor is moved well beyond the gain bandwidth product of the regulator. In practice, this is difficult to
do and still maintain high frequency operation. Typically the
output impedance of the regulator is not simply resistive,
such that the reactive output impedance interacts with the
reactive impedance of the load resistance and capacitance.
In addition, it is necessary to place the dominant pole of
the circuit at a sufficiently low frequency such that the gain
of the regulator has fallen below unity before any of the
complex interactions between the output and the load occur.
The ILC7083/ILC7084 does not try to eliminate the output
pole, but incorporates it into the stability scheme. The load
and output capacitor forms a pole, which rolls off the gain of
the regulator below unity. In order to do this the output
impedance of the regulator must be high, looking like a
current source. The output stage of the regulator becomes a
transconductance amplifier, which converts a voltage to a
current with a substantial output impedance. The circuit
which drives the transconductance amplifier is the error
amplifier, which compares the regulator output to the band
gap reference and produces an error voltage as the input to
the transconductance amplifier. The error amplifier has a
dominant pole at low frequency and a “zero” which cancels
out the effects of the pole. The zero allows the regulator
to have gain out to the frequency where the output pole
continues to reduce the gain to unity. The configuration of
the poles and zero are shown in Figure 1. Instead of powering the critical circuits from the unregulated input voltage,
the CMOS RF LDO powers the internal circuits such as the
bandgap, the error amplifier and most of the transconductance amplifier from the boot strapped regulated output
voltage of the regulator. This technique offers extremely high
ripple rejection and excellent line transient response.
COMPENSATING
ZERO
UNITY GAIN
FREQUENCY
Figure 1. ILC7083/ILC7084 RF LDO Frequency Response
A block diagram of the regulator circuit used in the ILC7083
is shown in Figure 2, which shows the input-to-output isolation and the cascaded sequence of amplifiers that implement
the pole-zero scheme outlined above.
The ILC7083/ILC7084 is designed in a CMOS process with
some minor additions, which allow the circuit to be used at
input voltages up to 13V. The resulting circuit exceeds the
frequency response of traditional bipolar circuits. The
ILC7083/ILC7084 is very tolerant of output load conditions
with the inclusion of both short circuit and thermal overload
protection. The device has a very low dropout voltage,
typically a linear response of 1mV per milliamp of load
current, and none of the quasi-saturation characteristics of a
bipolar output devices. All the good features of the frequency
response and regulation are valid right to the point where the
regulator goes out of regulation in a 4 millivolt transition
region. Because there is no base drive, the regulator is
capable of providing high current surges while remaining in
regulation. This is shown in the high peak current of 500mA
which allows for the ILC7083/ILC7084 to be used in
systems that require short burst mode operation.
5
ILC7083/ILC7084
VIN
INTERNAL VDD
CNOISE
BANDGAP
REFERENCE
VREFD
TRANSCONDUCTANCE
AMPLIFIER
ERROR
AMPLIFIER
VOUT
FEEDBACK
GND
ON/OFF
Figure 2. ILC7083 RF LDO Regulator Block Diagram
Shutdown (ON/OFF) Operation
The ILC7083/ILC7084 output can be turned off by applying
0.6V or less to the device’s ON/OFF pin (pin 3). In shutdown
mode, the ILC7083/ILC7084 draws less than 1µA quiescent
current. In shutdown mode the output of ILC7083 is coupled
to a low impedance circuit which discharges the output
capacitor. The output of the ILC7083/ILC7084 is enabled by
applying 1.5V to 13V at the ON/OFF pin. In applications
where the ILC7083 output will always remain enabled, the
ON/OFF pin may be connected to VIN (pin 1). The ILC7083/
ILC7084’s shutdown circuitry includes hysteresis, as such
the device will operate properly even if a slow moving signal
is applied to the ON/OFF pin.
In normal operation, the die temperature should be limited to
under 150°C.
Adjustable Output Voltage
Figure 5 shows how an adjustable output voltage can be easily achieved using ILC7083/ILC7084-ADJ. The output voltage, VOUT is given by the following equation:
VOUT = 1.255V x (R1/R2 + 1)
R1
VOUT
Short Circuit Protection
The ILC7083/ILC7084 output can withstand momentary
short circuit to ground. Moreover, the regulator can deliver
very high output peak current due to its 1A instantaneous
short circuit current capability.
Thermal Protection
The ILC7083/ILC7084 also includes a thermal protection
circuit which shuts down the regulator when die temperature
exceeds 150°C due to overheating. In thermal shutdown,
once the die temperature cools to below 140°C, the regulator
is enabled. If the die temperature is excessive due to high
package power dissipation, the regulator’s thermal circuit
will continue to pulse the regulator on and off. This is called
thermal cycling.
Excessively high die temperature may occur due to high differential voltage across the regulator or high load current or
high ambient temperature or a combination of all three.
Thermal protection protects the regulator from such fault
conditions and is a necessary requirement in today’s designs.
6
COUT
VIN
CIN
R2
5 SOT23-5 4 VADJ
ILC7083-ADJ
or ILC7084-ADJ
1
2
3
ON
OFF
Figure 3. Application Circuit for Adjustable Output Voltage
For best results, a resistor value of 470kΩ or less may be
used for R2. The output voltage can be programmed from
2.5V to 12V.
Note that an external capacitor should not be connected
to the adjustable feedback pin (pin 4). Connecting an
external capacitor to pin 4 may cause regulator instability and lead to oscillations.
REV. 1.0.9 1/28/03
ILC7083/ILC7084
Maximum Output Current
The maximum output current available from the ILC7083/
ILC7084 is limited by the maximum package power dissipation as well as the device’s internal current limit. For a given
ambient temperature, TA, the maximum package power
dissipation is given by:
PD(MAX) = (TJ(MAX) – TA) / θJA
where TJ(MAX) = 150°C is the maximum junction temperature and θJA = 333°C/W is the package thermal resistance.
For example at TA = 85°C ambient temperature, the maximum package power dissipation is;
PD(MAX) = 195mW.
The maximum output current can be calculated from the following equation:
IOUT(MAX) < PD(MAX) / (VIN – VOUT)
For example at VIN = 6V, VOUT = 5V and TA = 85°C, the
maximum output current is IOUT(MAX) < 195mA. At higher
output current, the die temperature will rise and cause the
thermal protection circuit to be enabled.
Application Hints
Figure 4 shows the typical application circuit for the
ILC7083.
VOUT
5 SOT23-5 4
ILC7083
COUT
VIN
CNOISE
1
CIN
2
Output Capacitor Selection
Fairchild strongly recommends the use of low ESR
(equivalent series resistance) ceramic capacitors for COUT
and CNOISE. The ILC7083/ILC7084 is stable with low ESR
capacitor (as low as zero Ω). The value of the output
capacitor should be 1µF or higher. Either ceramic chip or
a tantalum capacitor may be used at the output.
Use of ceramic chip capacitors offer significant advantages
over tantalum capacitors. A ceramic capacitor is typically
cheaper than a tantalum capacitor, it usually has a smaller
footprint, lower height, and lighter weight than a tantalum
capacitor. Furthermore, unlike tantalum capacitors which are
polarized and can be damaged if connected incorrectly,
ceramic capacitors are non-polarized. Low value ceramic
chip capacitors with X5R or X7R dielectric are available in
the 100pF to 4.7µF range. Beware of using ceramic capacitors with Y5V dielectric since their ESR increases significantly at cold temperatures. Please see the table of
recommended ceramic capacitors for use at the output of
ILC7083/ILC7084.
Note: If a tantalum output capacitor is used then for stable
operation. We recommend a low ESR tantalum capacitor
with maximum rated ESR at or below 0.4Ω. Low ESR tantalum capacitors, such as the TPS series from AVX Corporation (www.avxcorp.com) or the T495 series from Kemet
(www.kemet.com) may be used.
In applications where a high output surge current can be
expected, use a high value but low ESR output capacitor for
superior load transient response. The ILC7083/ILC7084 is
stable with no load.
3
ON
OFF
Figure 4. Basic Application Circuit for
Fixed Output Voltage Versions
Input Capacitor
An input capacitor CIN of value 1µF or larger should be connected from VIN to the main ground plane. This will help to
filter supply noise from entering the LDO. The input capacitor should be connected as close to the LDO regulator input
pin as is practical. Using a high-value input capacitor will
offer superior line transient response as well as better power
supply ripple rejection. A ceramic or tantalum capacitor may
be used at the input of the LDO regulator.
Note that there is a parasitic diode from the LDO regulator
output to the input. If the input voltage swings below the regulator’s output voltage by a couple of hundred millivolts then
REV. 1.0.9 1/28/03
the regulator may be damaged. This condition must be
avoided. In many applications a large value input capacitor,
CIN, will hold VIN higher than VOUT and decay slower than
VOUT when the LDO is powered off.
Noise Bypass Capacitor
In low noise applications, the self noise of the ILC7083 can
be decreased further by connecting a capacitor from the
noise bypass pin (pin 4) to ground (pin 2). The noise bypass
pin is a high impedance node as such care should be taken in
printed circuit board layout to avoid noise pick-up from
external sources. Moreover, the noise bypass capacitor
should have low leakage.
Noise bypass capacitors with a value as low as 470pF may
be used. However, for optimum performance, use a 0.01µF
or larger, ceramic chip capacitor. Note that the turn on and
turn off response of the ILC7083 is inversely proportional to
the value of the noise bypass capacitor. For fast turn on and
turn off, use a small value noise bypass capacitor. In applications where exceptionally low output noise is not required,
consider omitting the noise bypass capacitor altogether.
7
ILC7083/ILC7084
The ESR of a capacitor is a measure of the resistance due to
the leads and the internal connections of the component.
Typically measured in mΩ (milli-ohms) it can increase to
ohms in some cases.
Wherever there is a combination of resistance and current,
voltages will be present. The control functions of LDOs use
two voltages in order to maintain the output precisely; VOUT
and VREF.
With reference to the block diagram in Figure 4, VOUT is fed
back to the error amplifier and is used as the supply voltage
for the internal components of the ILC7083/ILC7084. So
any change in VOUT will cause the error amplifier to try to
compensate to maintain VOUT at the set level and noise on
VOUT will be reflected into the supply of each internal
components of the ILC7083/ILC7084. So any change in
VOUT will cause the error amplifier to try to compensate to
maintain VOUT at the set level and noise on VOUT will be
reflected into the supply of each internal circuit. The reference voltage, VREF, is influenced by the CNOISE pin. Noise
into this pin will add to the reference voltage and be fed
through the circuit. These factors will not cause a problem if
some simple steps are taken. Figure 5 shows where these
added ESR resistances are present in the typical LDO circuit.
VOUT
IOUT
R*
IC
COUT
RC
5 SOT-23-5 4
CNOISE
ILC7083
VIN
1
R*
CIN
2
RF LDOTM
Regulator
3
ON
Printed Circuit Board Layout Guidelines
As was mentioned in the previous section, to take full advantage of any high performance LDO regulator requires paying
careful attention to grounding and printed circuit board
(PCB) layout.
VOUT IOUT
I1
COUT
RPCB
ESR
RPCB
5 SOT-23-5 4
CNOISE
ILC7083
VIN
CIN
1
RPCB
2
3
RPCB
ON
OFF
Figure 6. Inherent PCB resistance
Figure 7 shows the effects of poor grounding and PCB
layout magnified by the ESR and PCB resistances and
the accumulation of current flows.
Note that particularly during high output load current, the
LDO regulator’s ground pin and the ground return for COUT
and CNOISE are not at the same potential as the system
ground. This is due to high frequency impedance caused by
PCB’s trace inductance and DC resistance. The current loop
between COUT, CNOISE and the LDO regulator’s ground pin
will degrade performance of the LDO.
OFF
Figure 5. ESR Present in COUT and CNOISE
With this in mind low ESR components will offer better
performance where the LDO may be subjected to large load
transients current. ESR is less of a problem with CIN as the
voltage fluctuations at the input will be filtered by the LDO.
However, being aware of these current flows, there is also
another potential source of induced voltage noise from the
resistance inherent in the PCB trace. Figure 6 shows where
the additive resistance of the PCB can manifest itself. Again
8
these resistances may be very small, but a summation of
several currents can develop detectable voltage ripple and
will be amplified by the LDO. Particularly the accumulation
of current flows in the ground plane can develop significant
voltages unless care is taken. With a degree of care, the
ILC7083/ILC7084 will yield outstanding performance.
ESR
The Effects of ESR (Equivalent Series
Resistance)
Figure 8 shows an optimum schematic. In this schematic,
high output surge current has little effect on the ground current and noise bypass current return of the LDO regulator.
Note that the key difference here is that COUT and CNOISE are
directly connected to the LDO regulator’s ground pin. The
LDO is then separately connected to the main ground plane
and returned to a single point system ground.
The layout of the LDO and its external components are also
based on some simple rules to minimize EMI and output
voltage ripple.
REV. 1.0.9 1/28/03
ILC7083/ILC7084
VOUT
ILC7083
SOT-23-5
I LOAD
+IC OUT
+IC NOISE
COUT
3
CNOISE
GND2
C IN
True GND
(0V)
2
GND
1
VIN
ON/OFF
GND1
LOAD
CNOISE
4
5
ICOUT
GND3
I LOAD
+IC OUT
+IC NOISE
GND4
GND5
I LOAD
I LOAD
+IC OUT
+IGND
Figure 7. Effects of Poor Circuit Layout
VOUT
5
4
C OUT
ILC7083
SOT-23-5
VIN
1
2
ON/OFF
DC/DC
Converter
VBATT
ESR<0.5
3
LOAD
C NOISE
Local
Ground
CIN
+
GND
Ground Plane
Ground Plane
Ground Plane
Ground Plane
Figure 8. Recommended Application Circuit Schematic
Fairchild Semiconductor - Eval. Board
Figure 9. Recommended Application Circuit Layout (not drawn to scale)
Note, ground plane is bottom layer of PCB and connects to top layer ground connections through vias.
REV. 1.0.9 1/28/03
9
ILC7083/ILC7084
Evaluation Board Parts List (for Figure 9)
Label
Part Number
Manufacturer
Description
U1
ILC7083AIM5-30
J1
69190-405
Berg
Cin
GRM40 Y5V 105Z16
muRata
Cnoise
ECU-V1H103KBV
Panasonic
Ceramic capacitor, 0.01µF,16V, SMT (size 0603)
Cout
GRM42-6X5R475K10
muRata
Ceramic capacitor, 4.7µF,16V, SMT (size 1206)
Fairchild Semiconductor 150mA RF LDO™ regulator
Connector, four position header
Ceramic capacitor, 1µF,16V, SMT (size 0805)
Grounding Recommendations
Layout Considerations
1.
Connect CIN between VIN of the ILC7083 and the
“GROUND PLANE”.
1.
2.
Keep the ground side of COUT and CNOISE connected to
the “LOCAL GROUND” and not directly to the
“GROUND PLANE”.
Place all RF LDO related components; ILC7083, input
capacitor CIN, noise bypass capacitor CNOISE and output
capacitor COUT as close together as possible.
2.
Keep the output capacitor COUT as close to the ILC7083
as possible with very short traces to the VOUT and GND
pins.
On multilayer boards use component side copper for
grounding around the ILC7083 and connect back to a
“GROUND PLANE” using vias.
3.
The traces for the related components; ILC7083, input
capacitor CIN, noise bypass capacitor CNOISE and output
capacitor COUT can be run with minimum trace widths
close to the LDO.
4.
Maintain a separate “LOCAL GROUND” remote from
the “GROUND PLANE” to ensure a quiet ground near
the LDO.
3.
4.
If using a DC-DC converter in your design, use a star
grounding system with separate traces for the power
ground and the control signals. The star should radiate
from where the power supply enters the PCB.
Figure 9 shows how this circuit can be translated into a PCB
layout.
Recommended Ceramic Output Capacitors
COUT
Capacitor Size
IOUT
Dielectric
Part Number
Capacitor Vendor
1µF
0805
0 to 150mA
X5R
C2012X5R1A105KT
TDK
0805
X7R
GRM40X7R105K010
muRata
0805
X7R
LMK212BJ105KG
Taiyo-Yuden
1206
X7R
GRM42-6X7R105K016
muRata
1206
X7R
EMK316BJ105KL
Taiyo-Yuden
1206
X5R
TMK316BJ105KL
Taiyo-Yuden
X5R
GRM40X5R225K 6.3
muRata
0805
X5R
C2012X5R0J225KT
TDK
1206
X5R
EMK316BJ225ML
Taiyo-Yuden
X5R
GRM42-6X5R475K010
muRata
X7R
LMK316BJ475ML
Taiyo-Yuden
2.2µF
4.7µF
0805
1206
1206
10
0 to 150mA
0 to 150mA
REV. 1.0.9 1/28/03
ILC7083/ILC7084
Typical Performance Characteristics ILC7083/ILC7084
Unless otherwise specified: TA = 25°C, VIN = VOUT(NOM) + 1V, ON/OFF pin tied to VIN
Dropout Characteristics
Output Voltage vs Temperature
3.4
3.015
3.01
Output voltage (V)
VOUT = 3.3V
COUT = 1µF (Ceramic)
VOUT = 3.0V
COUT = 1µF (Ceramic)
IOUT = 0mA
IOUT = 10mA
IOUT = 50mA
3.3
VOUT (V)
3.005
3
2.995
3.2
IOUT = 100mA
IOUT = 150mA
3.1
2.99
3
2.985
-50
0
50
100
3
150
3.2
3.6
VIN (V)
Temperature (°C)
Dropout Voltage vs Temperature
Dropout Voltage vs IOUT
250
250
IOUT = 150mA
VOUT = 3.0V
200
IOUT = 100mA
150
100
IOUT = 50mA
50
Dropout voltage (mV)
VOUT = 3.0V
Dropout voltage (mV)
3.4
TA = 85°C
200
TA = 25°C
150
100
TA = –40°C
50
IOUT = 0mA
0
0
–40
25
85
0
Temperature (°C)
100
150
Line Transient Response
Ground Current vs Input Voltage
6
150
VIN (V)
VOUT = 3.0 V
IOUT = 10mA
COUT = 1µF (Ceramic)
IOUT = 50mA
125
IOUT = 150mA
5
VIN: tr/tf < 1 µs
VOUT = 3.0V
COUT = 2.2 µF (Ceramic)
IOUT = 100 mA
IOUT = 0mA
4
100
VOUT (V)
IGND (µA)
50
Output Current (mA)
IOUT = 100mA
75
3.01
3.00
2.99
2.98
50
2
4
6
8
10
12
14
5µs/div
VIN (V)
REV. 1.0.9 1/28/03
11
ILC7083/ILC7084
Typical Performance Characteristics ILC7083/ILC7084
Unless otherwise specified: TA = 25°C, VIN = VOUT(NOM) + 1V, ON/OFF pin tied to VIN
Load Transient Response
VOUT (V)
3.15
3.10
Short Circuit Current
VOUT = 3.0V
COUT = 1 µF || 0.47 µF (Ceramic)
Output Shorted to Gnd
1.5 at time, t = 0
3.05
3.00
IOUT (mA)
1.0
ISC (A)
2.95
0.5
100
0
1
100µs/div
t=0
10
5
VOUT = 2.8V
IOUT = 10mA
COUT = 1µF
Without CNOISE Capacitor
15
10
5
0
3
3
2
2
VOUT (V)
0
1
0
0
100µS/div
VON/OFF (V)
5
VOUT = 2.8V
IOUT = 10mA
CNOISE = 0.01µF, COUT = 1µF
On/Off Transient Response
15
10
5
0
0
3
3
2
2
VOUT (V)
VOUT (V)
VON/OFF (V)
On/Off Transient Response
10
1
0
5mS/div
VOUT = 2.8V
IOUT = 150mA Without CNOISE Capacitor
COUT = 1µF
1
100µS/div
15
5ms/div
On/Off Transient Response
VON/OFF (V)
15
VOUT (V)
VON/OFF (V)
On/Off Transient Response
12
Thermal Cycling
VIN = 4V
VOUT = 2.8V
IOUT = 150mA
CNOISE = 0.01µF, COUT = 1µF
1
0
5mS/div
REV. 1.0.9 1/28/03
ILC7083/ILC7084
Typical Performance Characteristics ILC7083/ILC7084
Unless otherwise specified: TA = 25°C, VIN = VOUT(NOM) + 1V, ON/OFF pin tied to VIN
Spectral Noise Density
Spectral Noise Density
10
Noise (µV/Rt Hz)
VOUT = 2.8V
IOUT = 50mA
CNOISE = 0.01µF
1
Noise (µV/Rt Hz)
10
COUT = 1µF (Ceramic)
0.1
COUT = 2.2µF or 4.7µF (Ceramic)
0.01
VOUT = 2.8V
COUT = 2.2µF
CNOISE = 0.01µF
1
IOUT = 50mA, 100mA or 150 mA
0.1
0.01
IOUT = 1 mA
COUT = 10µF (Ceramic)
0.001
0.001
10
100
1K
10K
1M
100K
10M
10
100
1K
Frequency (Hz)
Output Noise Voltage vs. CNOISE
Output Noise Voltage vs. CNOISE
90
VOUT = 3V
IOUT = 10mA
COUT = 2.2µF(Ceramic)
CNOISE = 1.2nF
50
40
30
80
8.2nF
0.039µF
0.047µF
20
0.022µF
60
50
40
5.6nF
8.2nF
0.039µF
30
20
0.01µF
10
0.047µF
100 Hz–
100 KHz
300 Hz–
50 KHz
0.022µF
0.016µF
10
0
100 Hz–
50 KHz
VOUT = 3V
IOUT = 10mA
COUT = 4.7µF(Ceramic)
CNOISE = 1.2nF
70
5.6nF
Noise (µVrms)
Noise (µVrms)
70
60
0
300 Hz–
100 KHz
100 Hz–
50 KHz
100 Hz–
100 KHz
Freq Band
300 Hz–
50 KHz
300 Hz–
100 KHz
Freq Band
Ripple Rejection vs. Frequency
Ripple Rejection vs. Frequency
VOUT = 3V
IOUT = 10mA
100
COUT = 4.7µF
80
COUT = 10µF
60
COUT = 1µF
40
COUT = 2.2µF
20
Ripple Rejection (dB)
80
120
Ripple Rejection (dB)
1M
100K
Frequency (Hz)
90
80
10K
VOUT = 2.8V
IOUT = 150mA
70
COUT = 2.2µF
COUT = 4.7µF
60
50
40
30
COUT = 1µF
COUT = 10µF
20
10
0
0
10
100
1K
10K
100K
Frequency (Hz)
REV. 1.0.9 1/28/03
1M
10M
10
100
1K
10K
100K
1M
10M
Frequency (Hz)
13
ILC7083/ILC7084
Mechanical Dimensions
8-Lead Plastic Surface Mount (SOIC)
Inches
Symbol
Min.
A
A1
B
C
D
E
e
H
h
L
N
α
ccc
Millimeters
Max.
Min.
Max.
.053
.069
.004
.010
.013
.020
.0075
.010
.189
.197
.150
.158
.050 BSC
1.35
1.75
0.10
0.25
0.33
0.51
0.20
0.25
4.80
5.00
3.81
4.01
1.27 BSC
.228
.010
.016
5.79
0.25
0.40
.244
.020
.050
8
6.20
0.50
1.27
8
0°
8°
0°
8°
—
.004
—
0.10
8
Notes:
Notes
1. Dimensioning and tolerancing per ANSI Y14.5M-1982.
2. "D" and "E" do not include mold flash. Mold flash or
protrusions shall not exceed .010 inch (0.25mm).
3. "L" is the length of terminal for soldering to a substrate.
4. Terminal numbers are shown for reference only.
5
2
2
5. "C" dimension does not include solder finish thickness.
6. Symbol "N" is the maximum number of terminals.
3
6
5
E
1
H
4
h x 45°
D
C
A1
A
SEATING
PLANE
e
B
14
–C–
LEAD COPLANARITY
α
L
ccc C
REV. 1.0.9 1/28/03
ILC7083/ILC7084
5-Lead Plastic Surface Mount (SOT-23-5)
Symbol
A
A1
B
c
D
E
e
e1
H
L
α
Inches
Millimeters
Min.
Max.
Min.
Max.
.035
.000
.008
.003
.106
.059
.057
.006
.90
.00
.20
.08
2.70
1.50
1.45
.15
.020
.010
.122
.071
.037 BSC
.075 BSC
.087
.126
.004
.024
0°
10°
Notes:
Notes
1. Package outline exclusive of mold flash & metal burr.
2. Package outline exclusive of solder plating.
3. EIAJ Ref Number SC-74A.
.50
.25
3.10
1.80
.95 BSC
1.90 BSC
2.20
3.20
.10
.60
0°
10°
e
B
L
E
H
e1
c
D
A
A1
REV. 1.0.9 1/28/03
15
ILC7083/ILC7084
Ordering Information (TA = -40°C to +85°C)
Part Number
Output Voltage (V)
Package
Package Marking
ILC7083AIM525X
2.5
SOT-23-5
BM
ILC7083AIM527X
2.7
SOT-23-5
BN
ILC7083AIM5285X
2.85
SOT-23-5
BJ
ILC7083AIM530X
3.0
SOT-23-5
BB
ILC7083AIM533X
3.3
SOT-23-5
BC
ILC7083AIM536X
3.6
SOT-23-5
BD
ILC7083AIM550X
5.0
SOT-23-5
BE
Adjustable
SOT-23-5
BF
ILC7083AIK30X
3.0
SOIC-8
7083A1K3
ILC7083AIKADJ
Adjustable
SOIC-8
7083A1K
ILC7084AIM5ADJX
Adjustable
SOT-23-5
DF
ILC7083AIM5ADJX
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO
ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME
ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN;
NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES
OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body,
or (b) support or sustain life, and (c) whose failure to
perform when properly used in accordance with
instructions for use provided in the labeling, can be
reasonably expected to result in a significant injury of the
user.
2. A critical component in any component of a life support
device or system whose failure to perform can be
reasonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
www.fairchildsemi.com
1/28/03 0.0m 001
Stock#DS30007083
2003 Fairchild Semiconductor Corporation
Similar pages