EVERLIGHT IRM-2638-DIP-A

EVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet
Infrared Remote-Control Receiver Module
IRM-26xx-DIP-A SERIES
Features :
‧High protection ability against EMI .
‧Circular lens to improve the receive characteristic.
‧Line-up for various center carrier frequencies.
‧Low voltage and low power consumption.
‧Side-Received DIP Type.
‧High immunity against ambient light.
‧Photodiode with integrated circuit.
‧TTL and CMOS compatibility.
‧Long reception distance.
‧High sensitivity.
‧Suitable burst length ≧10 pulses/burst.
‧The product itself will remain within RoHS compliant version.
‧Pb free
Descriptions
The IRM-26xx-DIP-A SERIES are miniaturized
receivers for infrared remote control systems. PIN diode and
preamplifier are assembled on lead frame, the epoxy package
is designed as IR filter. The demodulated output signal can
directly be decoded by a microprocessor. IRM-26xx-DIP-A
SERIES is the standard IR remote control receiver series,
supporting all major transmission codes.
Applications
1. Light detecting portion of remote control
․AV instruments such as Audio, TV, VCR, CD, MD, etc.
․Home appliances such as Air-conditioner, Fan , etc.
․The other equipments with wireless remote control.
․CATV set top boxes
․Multi-media Equipment
PART
MATERIAL
COLOR
Chip
Silicon
---
Compound
Epoxy
Black
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Device No:DMO-026-392
Prepared date:10-22-2005
Rev 1
Prepared by:
Page: 1 of 9
Cindy Lin
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-26xx-DIP-A SERIES
Package Dimensions
OUT
GND
Vcc
Notes: 1.All dimensions are in millimeters.
2.Tolerances unless dimensions ±0.3mm.
Available Types For Different Carrier
Frequencies
Type
Carrier Frequencies
(Typ)
IRM-2633-DIP-A
33 kHz
IRM-2638-DIP-A
38 kHz
IRM-2640-DIP-A
40 kHz
IRM-2656-DIP-A
56 kHz
PCB Layout for Electrical Circuit
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Device No:DMO-026-392
Prepared date:10-22-2005
Rev 1
Prepared by:
Page: 2 of 9
Cindy Lin
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-26xx-DIP-A SERIES
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Rating
Unit
Supply Voltage
Vcc
0~6
V
Operating Temperature
Topr
-25 ~ +80
℃
Storage Temperature
Tstg
-40 ~ +85
℃
Soldering Temperature
Tsol
260
℃
Notice
4mm from mold body
less than 10 seconds
Recommended Operating Condition
Supply Voltage Rating: Vcc =4.5V to 5.5V
Electro-Optical Characteristics (Ta=25℃, and Vcc=5 V)
Parameter
Symbol
MIN.
TYP.
MAX.
Unit
Condition
Consumption Current
Icc
---
1.2
---
mA
No signal input
Peak Wavelength
λp
---
940
---
nm
L0
14
---
---
L45
6
---
---
Half Angle(Horizontal)
Θh
---
45
---
deg
Half Angle(Vertical)
Θv
---
45
---
deg
High Level Pulse Width
TH
400
---
800
μs
Low Level Pulse Width
TL
400
---
800
μs
High Level Output Voltage
VH
4.5
---
---
V
Low Level Output Voltage
VL
---
0.2
0.5
V
Reception Distance
m
At the ray axis
*1
At the ray axis
*2
*1:The ray receiving surface at a vertex and relation to the ray axis in the range of θ= 0° and θ=45°.
*2:A range from 30cm to the arrival distance. Average value of 50 pulses.
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Device No:DMO-026-392
Prepared date:10-22-2005
Rev 1
Prepared by:
Page: 3 of 9
Cindy Lin
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-26xx-DIP-A SERIES
The Notice of Application:
Transmission remote control signal consist of four parts: Encode Part, IR Transmitter Source, IRM
device, Decode Part
1. When IRM-26xx code select frequency, it need to well understand the center system of
encode part.
2. Strong or weak light of IR Transmitter can affect distance of transmission.
3. Minimum Burst Length Tburst (number of pulses per burst) : 10 cycles
4. It needs to ensure the translation range of decode part if it is applied to the pulse-width range.
If the above items hardly assure of its application, it’ll cause NG(no good) message from the edge
of signal.
Test Method:
The specified electro-optical characteristics is satisfied under the following
Conditions at the controllable distance.
cMeasurement place
A place that is nothing of extreme light reflected in the room.
dExternal light
Project the light of ordinary white fluorescent lamps which are not high
Frequency lamps and must be less then 10 Lux at the module surface.
(Ee≦10Lux)
eStandard transmitter
A transmitter whose output is so adjusted as to Vo=400mVp-p and the output
Wave form shown in Fig.-1.According to the measurement method shown in
Fig.-2 the standard transmitter is specified.
However , the infrared photodiode to be used for the transmitter should be
λp=940nm,Δλ=50nm. Also, photodiode is used of PD438B(Vr=5V).
(Standard light / Light source temperature 2856°K).
fMeasuring system
According to the measuring system shown in Fig.-3
Fig.-1
Transmitter Wave Form
D.U.T output Pulse
Carrier frequency is adjusted to
center frequency of each product.
IR TANSMITTER
OUTPUT WAVE FORM
OUTPUT PULSE
OF DEVICE
Duty=0.5
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Device No:DMO-026-392
Prepared date:10-22-2005
Rev 1
Prepared by:
Page: 4 of 9
Cindy Lin
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-26xx-DIP-A SERIES
Fig.-2
Measuring Method
Fig.-3
Measuring System
20cm
10k
+5.0± 0.1V
L: Transmission Distance
Vcc
OUT
θ θ
10uF
D.U.T
Standard Transmitter
Vout
Standard Transmitter
Vout
100k
GND
θ: Angle Of Horizontal & Vertical Direction
Oscilloscope
Block Diagram:
VCC
Noise Det.&
Gain Ctrl.
IN
I-V
Converter
&Input
Bias
Control
Pre
Amp
AGC
Amp
Voltage
Reference
Circuit
Band-pass
Fiter
Limit
Amp
Integrator
&Wave
Shaping
Comparator
Output
Stage
Fset Bias Circuit
Frequency
Setting
Frequency
Trimming
Threshold
Control
Circuit
GND
Application Circuit:
RC Filter should be connected closely between Vcc pin and GND pin.
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Device No:DMO-026-392
Prepared date:10-22-2005
Rev 1
Prepared by:
Page: 5 of 9
Cindy Lin
OUT
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-26xx-DIP-A SERIES
Typical Electro-Optical Characteristics Curves
Fig.-4 Relative Spectral Sensitivity vs. Wavelength
Fig.-5 Relative Transmission Distance vs. Direction
θ
Fig.-7 Arrival Distance vs. Supply Voltage
17.5
17.0
14.0
14.0
Transmission Distance Lc (m)
Transmission Distance Lc (m)
Fig.-6 Arrival Distance vs. Ambient Temperature
10.5
7.0
3.5
10.5
7.0
3.5
Supply Voltage Vcc (V)
Ambient Temperature Ta (°C)
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Device No:DMO-026-392
Prepared date:10-22-2005
Rev 1
Prepared by:
Page: 6 of 9
Cindy Lin
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-26xx-DIP-A SERIES
Typical Electro-Optical Characteristics Curves
Relative Transmission Distance (%)
Relative Transmission Distance (%)
Fig.-8 Relative Transmission Distance vs. Center Carrier Frequency
IRM-2633
IRM-2638
Center Carrier Frequency (kHz)
Center Carrier Frequency (kHz)
Relative Transmission Distance (%)
Relative Transmission Distance (%)
Fig.-8 Relative Transmission Distance vs. Center Carrier Frequency
IRM-2640
IRM-2656
Center Carrier Frequency (kHz)
Center Carrier Frequency (kHz)
Output Pulse Width (μsec)
Fig.-9 Relative Transmission Distance vs. Center Carrier Frequency
Transmission Distance Lc (m)
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Device No:DMO-026-392
Prepared date:10-22-2005
Rev 1
Prepared by:
Page: 7 of 9
Cindy Lin
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-26xx-DIP-A SERIES
█ Reliability Test Item And Condition
The reliability of products shall be satisfied with items listed below.
Confidence level: 90%
LTPD: 10%
Test Items
Test Conditions
Failure Judgement
Criteria
Samples(n)
Defective(c)
1 cycle
Temperature cycle
-40℃ +25℃ +85℃
(30min)(5min)(30min)
300 cycle test
Temp: +85℃
High temperature test Vcc:5V
1000hrs
Low temperature
storage
n=22,c=0
n=22,c=0
L0≦ L×0.8
L45≦ L×0.8
Temp: -40℃
1000hrs
n=22,c=0
High temperature
High humidity
Ta: 85℃,RH: 85%
1000hrs
Solder heat
Temp: 260±5℃ 10sec
4mm From the bottom of the package.
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Device No:DMO-026-392
Prepared date:10-22-2005
L: Lower specification
limit
n=22,c=0
n=22,c=0
Rev 1
Prepared by:
Page: 8 of 9
Cindy Lin
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-26xx-DIP-A SERIES
Packing Quantity Specification
1. 160PCS/1Box
2. 10Boxes/1Carton
Label Form Specification
CPN: Customer’s Production Number
P/N : Production Number
QTY: Packing Quantity
CAT: Ranks
HUE: None
REF: Reference
LOT No: Lot Number
MADE IN TAIWAN: Production Place
IRM-26xx-DIP-A
Notes
1. Above specification may be changed without notice. EVERLIGHT will reserve authority on
material change for above specification.
2. When using this product, please observe the absolute maximum ratings and the instructions
for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for
any damage resulting from use of the product which does not comply with the absolute
maximum ratings and the instructions included in these specification sheets.
3. These specification sheets include materials protected under copyright of EVERLIGHT
corporation. Please don’t reproduce or cause anyone to reproduce them without
EVERLIGHT’s consent.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http:\\www.everlight.com
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Device No:DMO-026-392
Prepared date:10-22-2005
Rev 1
Prepared by:
Page: 9 of 9
Cindy Lin