ISL51002 ® Data Sheet September 19, 2007 10-Bit Video Analog Front End (AFE) with Measurement and Auto-Adjust Features The ISL51002 3-channel, 10-bit Analog Front End (AFE) contains all the functionality needed to digitize analog YPbPr video from HDTV tuners, settop boxes, SD and HD DVDs, as well as RGB graphics signals from personal computers and workstations. The fourth generation analog design delivers 10-bit performance and a 165MSPS maximum conversion rate supporting resolutions up to 1080p/UXGA at 60Hz. The front end's programmable input bandwidth ensures sharp, low noise images at all resolutions. To accelerate and simplify mode detection, the ISL51002 integrates a sophisticated set of measurement tools that fully characterizes the video signal and timing, offloading the host microcontroller. Automatic Black Level Compensation (ABLC™) eliminates part-to-part offset variation, ensuring perfect black level performance in every application. The ISL51002's Digital PLL generates a pixel clock from the analog source's HSYNC or SOG (Sync-On-Green) signals. Pixel clock output frequencies range from 10MHz to 165MHz with sampling clock jitter of 250ps peak to peak. FN6164.2 Features • Automatic sampling phase adjustment • 10-bit triple Analog to Digital Converters with oversampling up to 8x in video modes • 165MSPS maximum conversion rate (ISL51002CQZ-165) • Robust, glitchless Macrovision®-compliant sync separator • Analog VCR “Trick Mode” support • ABLC™ for perfect black level performance • 4 channel input multiplexer • Precision sync timing measurement • RGB to YUV color space converter • Low PLL clock jitter (250ps p-p) • Programmable input bandwidth (10MHz to 450MHz) • 64 interpixel sampling positions • ±6dB gain adjustment rate • Pb-free (RoHS compliant) Related Literature Applications • Technical Brief TB363 “Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices (SMDs)”. • Flat Panel TVs • Front/Rear Projection TVs • PC LCD Monitors and Projectors • High Quality Scan Converters • Video/Graphics Processing Simplified Block Diagram VOLTAGE CLAMP RGB/YPbPrIN0 RGB/YPbPrIN1 RGB/YPbPrIN2 RGB/YPbPrIN3 OFFSET DAC ABLC™ 3 3 PGA 3 10-BIT ADC + COLOR SPACE CONVERTER 10 x3 RGB/YUVOUT 3 2 HSYNCOUT/VSYNCOUT FIELDOUT DEOUT SOGIN0, 1, 2, 3 HSYNCIN0, 1, 2, 3 HSOUT SYNC PROCESSING DIGITAL PLL PIXELCLKOUT VSYNCIN0, 1, 2, 3 MEASUREMENT, AUTOADJUST, AFE CONFIGURATION AND CONTROL 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2006, 2007. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL51002 Ordering Information PART NUMBER/PART MARKING TEMPERATURE RANGE (°C) PACKAGE PKG. DWG # ISL51002CQZ-110 (Note) 0 to +70 128 Ld MQFP (Pb-free) MDP0055 ISL51002CQZ-150 (Note) 0 to +70 128 Ld MQFP (Pb-free) MDP0055 ISL51002CQZ-165 (Note) 0 to +70 128 Ld MQFP (Pb-free) MDP0055 ISL51002EVALZ Evaluation Platform NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. Block Diagram VOLTAGE CLAMP OFFSET DAC 10 ABLC™ RIN0 RIN1 PGA RIN2 10-BIT ADC + 10 10 10 10 R[9:0] RIN3 VOLTAGE CLAMP OFFSET DAC 10 ABLC™ PGA GIN2 10-BIT ADC + GIN3 VOLTAGE CLAMP OFFSET DAC 10 ABLC™ BIN0 BIN1 PGA BIN2 + 10-BIT ADC 10 OUTPUT DATA FORMATTER GIN1 COLOR SPACE CONVERTER GIN0 10 G[9:0] B[9:0] DATACLK BIN3 DATACLK HSOUT INT CLAMPIN EXTCLKIN FBCIN SOGIN0,1,2,3 HSYNCIN0,1,2,3 VSYNCIN0,1,2,3 MEASUREMENT, AUTOADJUST, AFE CONFIGURATION AND CONTROL SYNC PROCESSING DE FIELD FBCOUT HSYNCOUT VSYNCOUT CLOCKINVIN COASTIN XTALIN DIGITAL PLL XCLKOUT XTALOUT SCL SDA SERIAL INTERFACE SADDR RESET 2 FN6164.2 September 19, 2007 ISL51002 Absolute Maximum Ratings Thermal Information 3.3V Supply Voltage (VA3.3, VD3.3, VPLLA3.3) . . . . . . . . . . . . . 4.6V 1.8V Supply Voltage (VA1.8, VD1.8, VADCD1.8). . . . . . . . . . . . . 2.5V Voltage on any Input Pin . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 6V Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20mA ESD Rating Human Body Model (Per MIL-STD-883 Method 3015.7) . . .3000V Machine Model (Per EIAJ ED-4701 Method C-111) . . . . . . . .300V Charged Device Model (Per EOS/ESD DS5.3, 4/14/93) . . .1000V Thermal Resistance (Typical) θJA (°C/W) θJC (°C/W) MQFP Package (Notes 1, 2) . . . . . . . . 30 16 Maximum Power Dissipation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2W Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +125°C Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C Supply Voltage Range . . . . . . . . . . . . . . . . . 3.3V ±10%, 1.8V ±10% CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 1. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 2. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside. Electrical Specifications SYMBOL Specifications apply for VA3.3 = VD3.3 = VPLLA3.3 = 3.3V, VA1.8 = VD1.8 = VPLLD1.8 = VADCD1.8 = 1.8V, pixel rate = 110MHz for ISL51002-110, 150MHz for ISL51002-150, 165MHz for ISL51002-165, fXTAL = 25MHz, and TA = +0°C to +70°C, unless otherwise specified. PARAMETER TEST LEVEL or NOTES MIN (Note 6) TYP MAX (Note 6) UNITS FULL CHANNEL CHARACTERISTICS Conversion Rate ISL51002-110 10 110 MHz ISL51002-150 10 150 MHz ISL51002-165 10 165 MHz ADC Resolution Missing Codes DNL (Full-Channel) INL (Full-Channel) 10 Bits Guaranteed monotonic Differential Non-Linearity None (Note 3) ISL51002-110 -0.99 ±0.5 +1.2 LSB ISL51002-150 -0.99 ±0.7 +1.3 LSB ISL51002-165 -0.99 ±0.8 +1.4 LSB ISL51002-110 ±1.9 ±3.6 LSB ISL51002-150 ±2.0 ±3.8 LSB ISL51002-165 ±2.6 ±4.0 LSB Integral Non-Linearity (Note 3) Gain Adjustment Range ±6 dB Gain Adjustment Resolution 10 Bits Gain Matching Between Channels Percent of full scale ±2 % Full Channel Offset Error, ABLC™ enabled ADC LSBs, over time and temperature Offset Adjustment Range (ABLC™ enabled or disabled) (see ABLC™ applications information section) ±0.5 ±3.0 ±50% LSB ADC Fullscale ANALOG VIDEO INPUT CHARACTERISTICS (RIN0-3, GIN0-3, BIN0-3) Input Range 0.35 Input Bias Current 3 DC restore clamp off 0.7 2.2 VP-P ±0.01 ±1 µA FN6164.2 September 19, 2007 ISL51002 Electrical Specifications SYMBOL Specifications apply for VA3.3 = VD3.3 = VPLLA3.3 = 3.3V, VA1.8 = VD1.8 = VPLLD1.8 = VADCD1.8 = 1.8V, pixel rate = 110MHz for ISL51002-110, 150MHz for ISL51002-150, 165MHz for ISL51002-165, fXTAL = 25MHz, and TA = +0°C to +70°C, unless otherwise specified. (Continued) PARAMETER TEST LEVEL or NOTES MIN (Note 6) Input Capacitance TYP MAX (Note 6) UNITS 5 pF 10 to 450 MHz Sync Tip Clamp 600 mV SOG Pull Down 1 µA 0 to 0.3 V 5 pF 0.4 to 3.2 V 240 mV ±10 nA 5 pF Full Power Bandwidth Programmable SOG INPUT CHARACTERISTICS (SOGIN0-3) VIH/VIL Input Threshold Voltage (relative to bottom of sync tip) Programmable - See Register Listing for Details Input Capacitance HSYNC INPUT CHARACTERISTICS (HSYNCIN0-3) VIH/VIL I CIN Input Threshold Voltage Programmable - See Register Listing for Details Hysteresis Centered around threshold voltage Input Leakage Current (Note 4) Input Capacitance DIGITAL INPUT CHARACTERISTICS (ALL DIGITAL INPUT PINS EXCEPT SCL, VSYNCIN0-3) VIH Input High Voltage VIL Input Low Voltage I CIN Input Leakage Current (Note 4) 2.0 V 0.8 RESET has a 65kΩ pullup to VD3.3 Input Capacitance V ±10 nA 5 pF SCHMITT DIGITAL INPUT CHARACTERISTICS (SCL, VSYNCIN0-3) VT+ Low To High Threshold Voltage VT- High To Low Threshold Voltage I CIN 1.45 V 0.95 Input Leakage Current Input Capacitance V ±10 nA 5 pF DIGITAL OUTPUT CHARACTERISTICS (ALL OUTPUT PINS EXCEPT INT AND SDA) VOH Output HIGH Voltage, IO = 8mA VOL Output LOW Voltage, IO = -8mA 2.4 V 0.4 V Open-drain, with 65kΩ pull-up to VD3.3 0.4 V Open-drain 0.4 V DIGITAL OUTPUT CHARACTERISTICS (INT) VOL Output LOW Voltage, IO = -8mA DIGITAL OUTPUT CHARACTERISTICS (SDA) VOL Output LOW Voltage, IO = -4mA POWER SUPPLY REQUIREMENTS VA3.3 Analog Supply Voltage, 3.3V VA1.8 3.0 3.3 3.6 V Analog Supply Voltage, 1.8V 1.65 1.8 2.0 V VD3.3 Digital Supply Voltage, 3.3V 3.0 3.3 3.6 V VD1.8 Digital Supply Voltage, 1.8V 1.65 1.8 2.0 V IA3.3 Analog Supply Current, 3.3V (Note 4) 45 90 mA 14 25 mA IPLLA3.3 4 Includes VPLLA3.3 Includes VADCD1.8, VPLLD1.8 FN6164.2 September 19, 2007 ISL51002 Electrical Specifications SYMBOL Specifications apply for VA3.3 = VD3.3 = VPLLA3.3 = 3.3V, VA1.8 = VD1.8 = VPLLD1.8 = VADCD1.8 = 1.8V, pixel rate = 110MHz for ISL51002-110, 150MHz for ISL51002-150, 165MHz for ISL51002-165, fXTAL = 25MHz, and TA = +0°C to +70°C, unless otherwise specified. (Continued) PARAMETER TEST LEVEL or NOTES MIN (Note 6) TYP MAX (Note 6) UNITS IA1.8 Analog Supply Current, 1.8V (Note 4) Includes 1.8V ADC reference current draw 270 375 mA ID3.3 Digital Supply Current, 3.3V (Note 4) Grayscale ramp input 30 60 mA ID1.8 Digital Supply Current, 1.8V (Note 4) Grayscale ramp input 65 95 mA 33 65 mA 1.8 10 mA 0.98 1.25 W 50 100 mW 250 450 ps p-p IADCD1.8 IPLLD1.8 PD Total Power Dissipation Grayscale ramp input Standby Mode AC TIMING CHARACTERISTICS PLL Jitter (Note 5) Sampling Phase Steps 5.6° per step 64 Sampling Phase Tempco Sampling Phase Differential Nonlinearity fXTAL Degrees out of +360° HSYNC Frequency Range 10 Crystal Frequency Range 12 ±1 ps/°C ±3 ° 150 kHz 27 MHz 25 tSETUP Data Valid Before Rising Edge of Dataclk 20pF DATACLK load, 20pF DATA load 1.8 ns tHOLD Data Valid After Rising Edge of Dataclk 20pF DATACLK load, 20pF DATA load 3.4 ns NOTES: 3. Linearity tested at room temperature and guaranteed across comercial temperature range by correlation to characterization. 4. Supply current specified at max pixel rate (165MHz) with gray scale video applied. 5. Jitter tested at rated frequencies (165MHz, 150MHz, 110MHz) and at minimum frequency (10MHz). 6. Parts are 100% tested at +25°C. Over-temperature limits established by characterization and are not production tested. 5 FN6164.2 September 19, 2007 ISL51002 Timing Diagrams Data Output Setup and Hold Timing DATACLK DATACLK tHOLD tSETUP PIXEL DATA RGB Output Data Timing and Latency THE HSYNC EDGE (PROGRAMMABLE LEADING OR TRAILING) THAT THE DPLL IS LOCKED TO. THE SAMPLING PHASE SETTING DETERMINES ITS RELATIVE POSITION TO THE REST OF THE AFE’S OUTPUT SIGNALS HSYNCIN ANALOG VIDEO IN P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 DATACLK 8 DATACLK PIPELINE LATENCY R/G/B[9:0] D0 D1 D2 D3 PROGRAMMABLE WIDTH AND POLARITY HSOUT YUV Output Data Timing and Latency THE HSYNC EDGE (PROGRAMMABLE LEADING OR TRAILING) THAT THE DPLL IS LOCKED TO. THE SAMPLING PHASE SETTING DETERMINES ITS RELATIVE POSITION TO THE REST OF THE AFE’S OUTPUT SIGNALS HSYNCIN ANALOG VIDEO IN P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 DATACLK 8 DATACLK PIPELINE LATENCY G[9:0] G0 (YO) G1 (Y1) G2 (Y2) G3 (Y3) R[9:0] B0 (UO) R0 (V0) B2 (U2) R2 (V2) B[9:0] PROGRAMMABLE WIDTH AND POLARITY HSOUT 6 FN6164.2 September 19, 2007 ISL51002 DATACLK VD3.3 GNDD R0 R1 R2 R3 R4 VD1.8 GNDD R5 R6 R7 R8 R9 VD3.3 GNDD 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 DATACLK 123 120 VSYNCOUT 124 HSYNCOUT INT 125 HSOUT DE 126 121 FIELD 127 122 GNDA FBCOUT 128 Pin Configuration (MQFP, ISL51002) BIN3 1 102 G0 VA1.8 2 101 G1 GIN3 3 100 G2 GNDA 4 99 G3 SOGIN3 5 98 G4 VA3.3 6 97 VD1.8 RIN3 7 96 GNDD GNDA 8 95 G5 BIN2 9 94 G6 VREFRED 10 93 G7 GIN2 11 92 G8 VA1.8 12 91 G9 SOGIN2 13 90 VD3.3 GNDA 14 89 GNDD RIN2 15 88 B0 VA3.3 16 87 B1 BIN1 17 86 B2 GNDA 18 85 B3 GIN1 19 84 B4 VREFGREEN 20 83 VD1.8 SOGIN1 21 82 GNDD VA1.8 22 81 B5 RIN1 23 80 B6 GNDA 24 79 B7 BIN0 25 78 B8 VA3.3 26 77 B9 GIN0 27 76 VD3.3 GNDA 28 75 GNDD SOGIN0 29 74 DTEST4 VREFBLUE 30 73 DTEST3 ISL51002CQZ-xxx 7 58 59 DTEST2 GNDD GNDD 64 57 GNDD COASTIN 56 GNDD CLAMPIN 55 EXTCLKIN 63 54 62 53 GNDD RESET 52 GNDD 61 51 DTEST1 GNDD 50 HSYNCIN0 CLOCKINVIN 49 VSYNCIN0 60 48 HSYNCIN1 NC 47 FBCIN 65 VSYNCIN1 66 38 46 37 NC 45 GNDA VSYNCIN2 SADDR HSYNCIN2 VPLLA3.3 67 44 SDA 36 HSYNCIN3 SCL 68 43 69 35 42 34 ATEST2 GNDD ATEST1 VSYNCIN3 GNDD 41 GNDD 70 VPLLD1.8 VD1.8 33 40 XCLKOUT 71 39 72 32 XTALIN 31 XTALOUT RIN0 VADCD1.8 FN6164.2 September 19, 2007 ISL51002 Pin Descriptions SYMBOL DESCRIPTION RIN0, 1, 2, 3 Analog inputs. Red channels. AC couple through 0.1µF. GIN0, 1, 2, 3 Analog inputs. Green channels. AC couple through 0.1µF. BIN0, 1, 2, 3 Analog inputs. Blue channels. AC couple through 0.1µF. VREFRED, VREFGREEN, VREFBLUE SOGIN0, 1, 2, 3 Analog inputs. Reference voltage for ADCs. Tie to 1.8V reference voltage (VA1.8 is acceptable if low noise). Decouple with 0.1µF capacitor to GNDA. Analog inputs. Sync on Green. Connect to corresponding Green channel video source through a 0.01µF capacitor in series with a 500Ω resistor. HSYNCIN0, 1, 2, 3 Digital high impedance 3.3V inputs with 240mV hysteresis. Connect to corresponding channel's HSYNC source. For 5V signals divide input with a 1k/1.9k divider. Place the divider as close as possible to the device pin. Place a 50pFcapacitor in parallel with the 1k resistor to reduce the filtering effect of the divider. VSYNCIN0, 1, 2, 3 Digital high impedance 3.3V inputs with 240mV hysteresis. Connect to corresponding channel's VSYNC source. For 5V signals divide input with a 1k/1.9k divider. Place the divider as close as possible to the device pin. Place a 50pF capacitor in parallel with the 1k resistor to reduce the filtering effect of the divider. COASTIN Digital 3.3V input. When this input is high and external COAST is selected, the PLL will coast, ignoring all transistions on the active channel’s HSYNC/SOG. CLAMPIN Digital 3.3V input.When this input is high and external CLAMP is selected, connects the selected channels inputs to the clamp DAC. CLOCKINVIN Digital 3.3V input. When high, changes the pixel sampling phase by 180°. Toggle at frame rate during VSYNC to allow 2x undersampling to sample odd and even pixels on sequential frames. Tie to DGND if unused. FBCIN Digital 3.3V input.Connect to the Fast Blank signal of a SCART connector. FBCOUT 3.3V digital output. A delayed version of the FBCIN signal, aligned with the digital pixel data. RESET Digital 3.3V input, active low, 70kΩ pullup to VD. Take low for at least 1µs and then high again to reset the ISL51002. This pin is not necessary for normal use and may be tied directly to the VD supply. XTALIN Analog input. Connect to external 12MHz to 27MHz crystal and load capacitor (see crystal spec for recommended loading). Typical oscillation amplitude is 1.0VP-P centered around 0.5V. XTALOUT Analog output. Connect to external 12MHz to 27MHz crystal and load capacitor (see crystal spec for recommended loading). Typical oscillation amplitude is 1.0VP-P centered around 0.5V. XCLKOUT 3.3V digital output. Buffered crystal clock output at fXTAL or fXTAL/2. May be used as system clock for other system components. SADDR Digital 3.3V input. Address = 0x98 (1001100x) when tied low. Address = 0 x 9A (1001101x) when tied high. SCL Digital input, 5V tolerant, 500mV hysteresis. Serial data clock for 2-wire interface. SDA Bidirectional Digital I/O, open drain, 5V tolerant. Serial data I/O for 2-wire interface. EXTCLKIN Digital 3.3V input. External clock input for AFE. R[9:0] 3.3V digital output. 10-bit Red channel pixel data. G[9:0] 3.3V digital output. 10-bit Green channel pixel data. B[9:0] 3.3V digital output. 10-bit Blue channel pixel data. DATACLK 3.3V digital output. Data (pixel) clock output. DATACLK 3.3V digital output. Inverse of DATACLK. HSOUT 3.3V digital output. HSYNC output aligned with pixel data. Use this output to frame the digital output data. This output is always purely horizontal sync (without any composite sync signals) HSYNCOUT 3.3V digital output. Buffered HSYNC (or SOG or CSYNC) output. This is typically used for measuring HSYNC period. This output will pass composite sync signals and Macrovision signals if present on HSYNCIN or SOGIN. VSYNCOUT 3.3V digital output. Buffered VSYNC output. For composite sync signals, this output will be asserted for the duration of the disruption of the normal HSYNC pattern. This is typically used for measuring VSYNC period. 8 FN6164.2 September 19, 2007 ISL51002 Pin Descriptions (Continued) SYMBOL DESCRIPTION INT Digital output, open drain, 5V tolerant. Interrupt output indicating mode change or command execution status. Pull high with a 4.7k resistor. DE 3.3V digital output. High when there is valid video data, low during horizontal and vertical blanking periods. FIELD 3.3V digital output. For interlaced video, this output will changes states to indicate whether current field is even or odd. Polarity is determined by configuration register. VA3.3 Power supply for the analog section. Connect to a 3.3V supply and bypass each pin to GNDA with 0.1µF. VA1.8 Power supply for the analog section. Connect to a 1.8V supply and bypass each pin to GNDA with 0.1µF. VPLLA3.3 Power supply for the analog PLL section. Connect to a 3.3V supply and bypass to GNDA with 0.1µF. GNDA Ground return for VA3.3, VA1.8, and VPLLA1.8. VD3.3 Power supply for all digital I/Os. Connect to a 3.3V supply and bypass each pin to GNDD with 0.1µF. VD1.8 Power supply for digital core logic. Connect to a 1.8V supply and bypass each pin to GNDD with 0.1µF. VADCD1.8 Power supply for the digital ADC section. Connect to a 1.8V supply and bypass to GNDD with 0.1µF. VPLLD1.8 Power supply for the digital PLL section. Connect to a 1.8V supply and bypass to GNDD with 0.1µF. GNDD Ground return for VD3.3, VD1.8, VADCD1.8, and VPLLD1.8. ATEST1, 2 For production use only. Tie to GNDA. DTEST1, 2, 3, 4 For production use only. Tie to GNDD. NC Reserved. Do not connect anything to these pins. 9 FN6164.2 September 19, 2007 Sync Flow 10 CH2 CH3 165 MHZ TRIPLE 10- BIT AFE 3 3 3 10 10 10-BIT 3X3 COLOR SPACE CONVERTER 10 DIGITAL OFFSET CONTROL (IF ABLC ENABLED) 10 10 DATA 10 10 10 OUTPUT FORMATTER 3 CH1 DECIMATOR CH0 10 3 10 DATA 10 DATA DATACLK HSOUT 10 GLITCH FILTER SOG SLICER A SOG0 EXTRACTED VSYNC SOG1 SYNC SEPARATOR SOG2 SOG SLICER B SOG3 MASK DIGITAL PLL INTERLACED COAST GEN. FIELD O/E MV EXT. COAST VSYNCOUT TRI-LEVEL DETECTION TRILEVEL VSYNC SELECT TIMING MEASUREMENT HSYNC1 HSYNC2 HSYNC SLICER B HSYNC3 ACTIVITY MONITOR INTERRUPT GENERATION VSYNC SLICER A VSYNC0 VSYNC1 AUTO ADJUST COLOR KEY: VSYNC2 VSYNC SLICER B VSYNC3 FN6164.2 September 19, 2007 CH0 TO CH3 SELECT AUTO POLLING INT DE ACTIVE VIDEO SIGNAL PATH ANALOG SIGNAL ACTIVE SYNC SIGNAL PATH MONITORING/ SUPPORT DIGITAL SIGNAL CRYSTAL OSCILLATOR SERIAL I/O XTALOUT ISL51002 HSYNC SLICER A HSYNC0 HSYNC/ CSYNC FROM SOG OR HSYNC SELECT HSYNCOUT MASK ISL51002 Register Listing ADDRESS REGISTER (DEFAULT VALUE) BITS FUNCTION NAME DESCRIPTION STATUS AND INTERRUPT REGISTERS 0x01 0x02 Selected Input Channel Characteristics, (read only) CH0 and CH1 Activity Status, (read only) 1:0 SYNC Type 00: Automatic Sync Selection logic could not find good sync on H, V, or SOG (Automatic Sync mode only) 01: SYNC on HSYNC/VSYNC 10: CSYNC on HSYNC 11: CSYNC on Green Channel (SOG) 2 HSYNC Polarity 0: HSYNC Active High 1: HSYNC Active Low 3 VSYNC Polarity 0: VSYNC Active High 1: VSYNC Active Low 4 Tri-level Sync 0: Bi-level SOG (if SOG is active) 1: Tri-level SOG 5 Interlaced (Only for CSYNC) 0: Non-interlaced or progressive signal 1: Interlaced signal 6 Macrovision 0: No Macrovision detected 1: Macrovision encoding detected 7 PLL Locked 0: PLL unlocked 1: PLL locked to incoming HSYNC 0 HSYNC0 Activity 0: HSYNC0 Inactive 1: HSYNC0 Active – There is a periodic signal with frequency >1kHz and consistent low/high times on this input 1 VSYNC0 Activity 0: VSYNC0 Inactive 1: VSYNC0 Active – There is a periodic signal with frequency >20Hz and consistent low/high times on this input SOG0 Activity 00: SOG0 Inactive – No transitions detected at the SOG Slicer output. 01: SOG0 Active – Non-periodic transitions detected at the SOG Slicer output – possibly valid SOG with a bad slicer threshold, or simply video with no valid SOG. 10: SOG0 Periodic – There is a periodic signal with frequency >1kHz and consistent low/high times on this input. This is most likely a valid SOG signal. 4 HSYNC1 Activity See HSYNC0 Activity description 5 VSYNC1 Activity See VSYNC0 Activity description SOG1 Activity See SOG0 Activity description 0 HSYNC2 Activity See HSYNC0 Activity description 1 VSYNC2 Activity See VSYNC0 Activity description SOG2 Activity See SOG0 Activity description 4 HSYNC3 Activity See HSYNC0 Activity description 5 VSYNC3 Activity See VSYNC0 Activity description SOG3 Activity See SOG0 Activity description 3:2 7:6 0x03 CH2 and CH3 Activity Status, (read only) 3:2 7:6 11 FN6164.2 September 19, 2007 ISL51002 Register Listing (Continued) ADDRESS 0x04 0x05 REGISTER (DEFAULT VALUE) BITS FUNCTION NAME DESCRIPTION Interrupt Status, 0 CH0 Sync Changed 0: No change 1: CH0 activity or polarity changed Write a 1 to each bit to clear it, 0xFF to clear all. 1 CH1 Sync Changed 0: No change 1: CH1 activity or polarity changed 2 CH2 Sync Changed 0: No change 1: CH2 activity or polarity changed 3 CH3 Sync Changed 0: No change 1: CH3 activity or polarity changed 4 Selected Input Channel Disrupted 0: No change 1: Currently selected Input Channel’s HSYNC or VSYNC signal has changed (fast notification of a mode change) 5 Selected Input Channel Changed 0: No change 1: Currently selected Input Channel’s HSYNC or VSYNC period or pulse width has settled to a new value and can be measured 6 VSYNC INT 0: Default state 1: VSYNC occurred 7 PADJ INT 0: Default state 1: Phase Adjustment function completed. 0 CH0 Mask 0: Generate interrupt if CH0 sync activity, polarity, period, or pulse width changes 1: Mask CH0 interrupt 1 CH1 Mask 0: Generate interrupt if CH1 sync activity, polarity, period, or pulse width changes 1: Mask CH1 interrupt 2 CH2 Mask 0: Generate interrupt if CH2 sync activity, polarity, period, or pulse width changes 1: Mask CH2 interrupt 3 CH3 Mask 0: Generate interrupt if CH3 sync activity, polarity, period, or pulse width changes 1: Mask CH3 interrupt 4 Input Disrupted Mask 0: Generate interrupt if selected Input Channel’s sync inputs are disrupted 1: Mask Input Channel interrupt 5 Input Changed Mask 0: Generate interrupt after selected Input Channel period or pulse width settles to new value 1: Mask Input Channel interrupt 6 VSYNC INT Mask 0: Generate interrupt every VSYNC 1: Mask VSYNC Interrupt 7 PADJ INT Mask 0: Generate interrupt upon phase adjustment block request completion 1: Mask Phase adjustment interrupt Interrupt Mask Register, (0xFF) 12 FN6164.2 September 19, 2007 ISL51002 Register Listing (Continued) ADDRESS REGISTER (DEFAULT VALUE) BITS FUNCTION NAME DESCRIPTION CONFIGURATION REGISTERS 0x10 0x11 Input Configuration, (0x00) Sync Source Selection, (0x00) 1:0 Input Channel Select Sets video muxes as well as HSYNC, VSYNC, and SOG input muxes. 0: CH0 1: CH1 2: CH2 (single-ended mode only) 3: CH3 (single-ended mode only) 2 Differential Mode Enable 0: Single-Ended Mode 1: Differential Mode 3 DC Coupled Input Enable 0: AC-coupled Inputs 1: DC-coupled Inputs 4 RGB YUV 0: RGB inputs (Clamp DAC = 300mV for R, G, B, half scale analog shift for R, G, and B, base ABLC target code = 0x00 for R, G, and B) 1: YPbPr inputs (Clamp DAC = 600mV for R and B, 300mV for G, half scale analog shift for G channel only, base ABLC target code = 0x00 for G, = 0x80 for R and B) 5 High Voltage Enable 0: Normal Input Range 1: Expanded 2.2V Input Range 6 EXT Clamp SEL 0: Internal CLAMP generation 1: External CLAMP source 7 EXT Clamp POL 0: Active high external CLAMP 1: Active low external CLAMP 0 Sync Select 0: Automatic (HSYNC, VSYNC sources selected based on sync activity. Multiplexer settings chosen are displayed in the Input Characteristics register.) 1: Manual (bits 1and 2 determine HSYNC and VSYNC source) 1 HSYNC Source 0: HSYNC input pin 1: SOG 2 VSYNC Source 0: VSYNC input pin 1: Sync Separator output Red channel gain, where: gain (V/V) = 0.5 + [9:0]/682 MSB/LSB 0x00 00: gain = 0.5 V/V (1.4VP-P input = full range of ADC) 0x55 00: gain = 1.0 V/V (0.7VP-P input = full range of ADC) 0xFF C0: gain = 2.0 V/V (0.35VP-P input = full range of ADC) 0x12 Red Gain MSB, (0x55) 7:0 Red Gain MSB 0x13 Red Gain LSB, (0x00) 5:0 N/A 7:6 Red Gain LSB 2 LSBs of 10-bit gain word See Red Gain 0x14 Green Gain MSB, (0x55) 7:0 Green Gain MSB 0x15 Green Gain LSB, (0x00) 5:0 N/A 7:6 Green Gain LSB See Red Gain See Red Gain 0x16 Blue Gain MSB, (0x55) 7:0 Blue Gain MSB 0x17 Blue Gain LSB, (0x00) 5:0 N/A 7:6 Blue Gain LSB See Red Gain 7:0 Red Offset MSB ABLC off: upper 8-bits to Red offset DAC ABLC enabled: Red digital offset 0x00 00 = min DAC value or -0x80 digital offset 0x80 00 = mid DAC value or 0x00 digital offset, 0xFF C0= max DAC value or +0x7F digital offset 0x18 Red Offset MSB, (0x80) 13 FN6164.2 September 19, 2007 ISL51002 Register Listing (Continued) ADDRESS 0x19 REGISTER (DEFAULT VALUE) Red Offset LSB, (0x00) BITS FUNCTION NAME DESCRIPTION 5:0 N/A 7:6 Red Offset LSB 2 LSBs of 10-bit offset word ABLC off: upper 8-bits to Green offset DAC ABLC enabled: Green digital offset (See Red Offset) 0x1A Green Offset MSB, (0x80) 7:0 Green Offset MSB 0x1B Green Offset LSB, (0x00) 5:0 N/A 7:6 Green Offset LSB See Red Offset ABLC off: upper 8-bits to Blue offset DAC ABLC enabled: Blue digital offset (See Red Offset) 0x1C Blue Offset MSB, (0x80) 7:0 Blue Offset MSB 0x1D Blue Offset LSB, (0x00) 5:0 N/A 7:6 Blue Offset LSB See Red Offset 0x1E PLL Htotal MSB, (0x06) 5:0 PLL Htotal MSB 14-bit HTOTAL. PLL updated on LSB write only. 0x1F PLL Htotal LSB, (0x98) 7:0 PLL Htotal LSB PLL updated on LSB write only. SXGA default 0x20 PLL Phase, (0x00) 5:0 PLL Sampling Phase Used to control the phase of the ADC’s sample point relative to the period of a pixel. Adjust to obtain optimum image quality. One step = 5.625° (1.56% of pixel period). 0x21 PLL Pre-coast, (0x04) 7:0 Pre-coast Number of lines the PLL will coast prior to the start of VSYNC. 0x22 PLL Post-coast, (0x04) 7:0 Post-coast Number of lines the PLL will coast after the end of VSYNC. 0x23 PLL Misc, (0x00) 0 PLL Lock Edge HSYNC 0: PLL locks to trailing edge of selected HSYNC (default) 1: PLL locks to leading edge of selected HSYNC 1 CLKINV ENABLE 0: CLKINV input ignored 1: CLKINV input enabled 2 Ext Coast SEL 0: Internal COAST generation 1: External COAST source 3 Ext Coast POL 0: Active high external COAST 1: Active low external COAST 4 EXT CLOCK 0: Internal pixel clock from DPLL 1: External pixel clock from EXTCLKin pin Pixel after Raw HSYNC trailing edge to begin DC restore and ABLC. 14-bits. 0x24 DC Restore and ABLC starting pixel MSB, (0x00) 5:0 DC Restore and ABLC starting pixel (MSB) 0x25 DC Restore and ABLC starting pixel LSB, (0x02) 7:0 DC Restore and ABLC starting pixel (LSB) 0x26 DC Restore Clamp Width, (0x10) 7:0 DC Restore clamp width 14 Only applies to DC restore clamp used for AC-coupled configurations. A value of 0x00 means the clamp DAC is never connected to the input. FN6164.2 September 19, 2007 ISL51002 Register Listing (Continued) ADDRESS 0x27 0x28 REGISTER (DEFAULT VALUE) BITS ABLC Configuration, (0x40) 0 ABLC Disable 0: ABLC on (default) - use 10-bit digital offset control. 0x000 = -0x200 LSB offset, 0x3FF = +0x1FF LSB offset, 0x200 = 0x000 LSB offset 1: ABLC off - use 10-bit offset DACs, bypass digital adder (add/subtract nothing, but keep same delay through channel) 1 Offset DAC Range 0: ±1/2 ADC fullscale (1 LSB = 1 ADC LSBs) 1: ±1/4 ADC fullscale (1 LSB = 0.5 ADC LSBs) 3:2 ABLC Pixel Width Number of black pixels averaged every line for ABLC function 00: 16 pixels [default] 01: 32 pixels 10: 64 pixels 11: 128 pixels 6:4 ABLC Bandwidth ABLC Time constant (lines) = 2([5+6:4]) 000 = 32 lines 100 = 512 lines (default) 111 = 4096 lines 0 Data Output Format 0: 4:4:4 (24-bit/30-bit output) 1: 4:2:2 (16-bit/20-bit output on G and R) 1 4:2:2 Order 0: First pixel on R channel is U 1: First pixel on R channel is V 2 4:2:2 Processing 0: U, V fitered (high quality) 1: Odd U, V pixels dropped (lower quality) 3 8-bit Mode 0: All 10-bits of each channel active 1: 2 LSBs of each channel driven low (in 8-bit applications, keep the LSBs from switching and generating noise) Oversampling 00: Normal operation (1x sampling) 01:2x oversampling, 2 samples averaged at ADC output 10:4x oversampling, 4 samples averaged at ADC output 11:8x oversampling, 8 samples averaged at ADC output Output Format 1, (0x00) 5:4 FUNCTION NAME DESCRIPTION In Oversampling mode, the HTOTAL, DC Restore/ABLC Start, DC Restore Width, and ABLC width values are automatically multiplied by the oversampling ratio. The pixel clock is divided by the oversampling ratio when the data is decimated. Decimator is reset on trailing edge of HSYNC. 6 15 RGB2YUV Color Space Conversion Enable 0: CSC Disabled 1: CSC Enabled Note: The data delay through the entire AFE is identical with CSC on and CSC off. FN6164.2 September 19, 2007 ISL51002 Register Listing (Continued) ADDRESS 0x29 REGISTER (DEFAULT VALUE) Output Format 2, (0x00) BITS FUNCTION NAME DESCRIPTION 0 DATACLK Polarity 0: Pixel data changes on falling edge (default) 1: Pixel data changes on rising edge 1 FIELD output polarity 0: Odd = low, Even = high (default) 1: Odd = high, Even = low 2 Macrovision 0: Digitize Macrovision encoded signals (default) 1: Blank AFE output for Macrovision encoded signals. If Macrovision is detected, AFE output is always 0x00 0x00 0x00 for RGB, or 0x00, 0x80, 0x80 for YUV. 3 HSOUT Polarity 0: Active High (default) 1: Active Low 4 HSOUT Lock Edge 0: HSOUT’s leading edge is locked to selected HSYNCIN’s lockedge. Trailing edge moves forward in time as HSOUT width is increased (default). 1: HSOUT’s trailing edge is locked to selected HSYNCIN’s lockedge. Leading edge moves backward in time as HSOUT width is increased. 5 XTALCLKOUT Frequency 0: XTALCLKOUT= fCRYSTAL (default) 1: XTALCLKOUT= fCRYSTAL/2 6 Enable XTALCLKOUT 0 = XTALCLKOUT is logic low (default) 1 = XTALCLKOUT enabled 0x2A HSOUT Width, (0x10) 7:0 HSOUT Width HSOUT Width in pixels, 0x00 to 0xFF. HSOUT Lock Edge determines whether leading or trailing edge is locked to HSYNCIN 0x2B Output Signal Disable, (0xFF) 0 Tri-state Red 0 = Outputs enabled 1 = Outputs in tri-state 1 Tri-state Green 0 = Outputs enabled 1 = Outputs in tri-state 2 Tri-state Blue 0 = Outputs enabled 1 = Outputs in tri-state 3 Tri-state SYNC 0 = HSOUT, HSYNCOUT, VSYNCOUT enabled 1 = Outputs in tri-state 4 Tri-state DATACLK 0 = Output enabled 1 = Output in tri-state 5 Tri-state DATACLKb 0 = Output enabled 1 = Output in tri-state 6 Tri-state DE 0 = Output enabled 1 = Output in tri-state 7 Tri-state Field 0 = Output enabled 1 = Output in tri-state 0 Red Power Down 0 = Red ADC operational (default) 1 = Red ADC powered down 1 Green Power Down 0 = Green ADC operational (default) 1 = Green ADC powered down 2 Blue Power Down 0 = Blue ADC operational (default) 1 = Blue ADC powered down 3 PLL Power Down 0 = PLL operational (default) 1 = PLL powered down Note: All digital outputs are tristated by default to ease multiplexing with other AFEs 0x2C Power Control, (0x00) 16 FN6164.2 September 19, 2007 ISL51002 Register Listing (Continued) ADDRESS 0x2D REGISTER (DEFAULT VALUE) XTAL CLOCK FREQ, (0x19) BITS 4:0 FUNCTION NAME Crystal Clock Frequency DESCRIPTION Crystal clock frequency in MHz (decimal). 0x00: Test Mode, Do not use. 0x01 through 0x0A: 10MHz, APLL DIV = 35 (0x23) 0x0B: 11MHz, APLL DIV = 32 0x0C: 12MHz, APLL DIV = 30 0x0D: 13MHz, APLL DIV = 27 0x0E: 14MHz, APLL DIV = 25 0x0F: 15MHz, APLL DIV = 24 0x10: 16MHz, APLL DIV = 22 0x11: 17MHz, APLL DIV = 21 0x12: 18MHz, APLL DIV = 20 0x13: 19MHz, APLL DIV = 19 0x14: 20MHz, APLL DIV = 18 0x15: 21MHz, APLL DIV = 17 0x16: 22MHz, APLL DIV = 16 0x17: 23MHz, APLL DIV = 16 0x18: 24MHz, APLL DIV = 15 0x19: 25MHz, APLL DIV = 14 0x1A: 26MHz, APLL DIV = 14 0x1B: 27MHz, APLL DIV = 13 0x1C: 28MHz, APLL DIV = 13 0x1D: 29MHz, APLL DIV = 13 0x1E: 30MHz, APLL DIV = 12 0x1F: 31MHz, APLL DIV = 12 0x2E AFE Bandwidth, (0x0E) 3:0 AFE BW 0x2F HSYNC Slicer Thresholds, (0x44) 3:0 Selected HSYNC Threshold HSYNC slicer threshold for selected input channel (only 3-bits used, lowest bit is ignored): 0000 = lowest (0.4V) 0100 = default (1.15V) 1111 = highest (3.2V) 7:4 Unselected HSYNC Threshold HSYNC threshold for monitoring unselected inputs. See Selected HSYNC Threshold for values. 3:0 SOG Threshold SOG slicer threshold: 0000 = lowest (0mV) 0110 = default (120mV) 1111 = highest (300mV) All values referred to voltage at HSYNC input pin, 300mV hysteresis 0x30 SOG Slicer Thresholds, (0x66) 17 -3dB point for AFE lowpass filter 0: 9MHz 1: 10MHz 2: 11MHz 3: 12MHz 4: 14MHz 5: 17MHz 6: 21 MHz 7: 24MHz 8: 30MHz 9: 38MHz A: 50MHz B: 75MHz C: 83MHz D: 105MHz E: 149MHz (default) F: 450MHz FN6164.2 September 19, 2007 ISL51002 Register Listing (Continued) ADDRESS 0x31 0x32 REGISTER (DEFAULT VALUE) HSYNC/SOG Config, (0x04) Sync Polling Control, (0x00) BITS 3:0 FUNCTION NAME DESCRIPTION Glitch Filter Width 0: 16 crystal clocks 1: 17 crystal clocks 2: 1 crystal clocks 3: 2 crystal clocks 4: 3 crystal clocks (default) 5: 4 crystal clocks 6: 5 crystal clocks 7: 6 crystal clocks 8: 7 crystal clocks 9: 8 crystal clocks 10: 9 crystal clocks 11: 10 crystal clocks 12: 11crystal clocks 13: 12 crystal clocks 14: 13 crystal clocks 15: 14 crystal clocks 4 Sync Glitch Filter Disable 0: glitch filter enabled 1: glitch filter disabled 5 SOG Hyst Disable 0: 40mV hysteresis enabled 1: 40mV hysteresis disabled 6 SOG LPF Disable 0: 14MHz SOG Low Pass Filter Enabled 1: 14MHz SOG Low Pass Filter Disabled 0 CH0 Polling 0: Enable 1: Disable 1 CH1 Polling 0: Enable 1: Disable 2 CH2 Polling 0: Enable 1: Disable 3 CH3 Polling 0: Enable 1: Disable 4 CH0 Connector Type 0: RGB DB15 (poll for HSYNC, CSYNC, and SOG) 1: Component (poll for SOG only) 5 CH1 Connector Type 0: RGB DB15 (poll for HSYNC, CSYNC, and SOG) 1: Component (poll for SOG only) 6 CH2 Connector Type 0: RGB DB15 (poll for HSYNC, CSYNC, and SOG) 1: Component (poll for SOG only) 7 CH3 Connector Type 0: RGB DB15 (poll for HSYNC, CSYNC, and SOG) 1: Component (poll for SOG only) These registers report a 16-bit value containing the number of crystal clocks inside a 16 consecutive HSYNC period window. This means the 16-bit number will reflect one HSYNC period with 1/16 LSB resolution - the last 4-bits of the measurement will be fractional. MEASUREMENT REGISTERS 0x40 HSYNC Period MSB, (read only) 7:0 HSYNC Period MSB 0x41 HSYNC Period LSB, (read only) 7:0 HSYNC Period LSB 0x42 HSYNC Width MSB, (read only) 7:0 HSYNC Width MSB 0x43 HSYNC Width LSB, (read only) 7:0 HSYNC Width LSB 18 These registers report a 16-bit value containing the number of crystal clocks inside 16 consecutive HSYNC pulses. This means the 16-bit number will reflect one HSYNC pulse width with 1/16 LSB resolution - the last 4-bits of the measurement will be fractional. FN6164.2 September 19, 2007 ISL51002 Register Listing (Continued) ADDRESS REGISTER (DEFAULT VALUE) BITS FUNCTION NAME DESCRIPTION 0x44 VSYNC Period MSB, (read only) 3:0 VSYNC Period MSB 0x45 VSYNC Period LSB, (read only) 7:0 VSYNC Period LSB 0x46 VSYNC Width, (read only) 6:0 VSYNC Width This register reports a 7-bit value containing the width the VSYNC pulse. The value returned is for true VSYNC only: it does not include serrations, EQ pulses, Macrovision pulses, etc. Units are either number of HSYNC periods or number of fCRYSTAL/512 periods, depending on setting of VSYNC Units register. 0x47 DE Start MSB, (0x00) 1:0 DE Start MSB 0x48 DE Start LSB, (0xF6) 7:0 DE Start LSB 10-bit value containing the number of pixel clocks between the trailing edge of HSOUT and the first valid pixel. SXGA default values. 0x49 DE Width MSB, (0x05) 3:0 DE Width MSB 0x4A DE Width LSB, (0x00) 7:0 DE Width LSB 0x4B Line Start MSB, (0x00) 1:0 Line Start MSB 0x4C Line Start LSB, (0x26) 7:0 Line Start LSB 0x4D Line Width MSB, (0x04) 3:0 Line Width MSB 0x4E Line Width LSB, (0x00) 7:0 Line Width LSB 0x4F Measurement Configuration, (0x00) These bits report a 12-bit value containing the width of one frame (= 2 fields for interlaced, = 1 field for progressive) of video. VSYNC period for measured channel = 256*VSYNC Period MSB + VSYNC Period LSB Units are either number of HSYNC periods or number of fCRYSTAL/512 periods, depending on setting of VSYNC Units register. 12-bit value containing the number of visible image pixels. SXGA default values. 10-bit value containing the number of lines between the trailing edge of VSYNCOUT and the first valid line. SXGA default values. 12-bit value containing the number of visible lines. SXGA default values. 0 VSYNC Units 0: VSYNC measurement reported in units of lines (HSYNC periods) 1: VSYNC measurement reported in units of 512 crystal clock periods 1 VSYNC_Linecount_Mode 0: New method (Integer count of HSOUTs) 1: Old method (Time measurement with rounding errors) PADJ Function Note: A write to this register executes the command contained in the three LSBs of the word written. Commands: 000: Reserved 001: Reserved 010: Reserved 011: SetPhase 100: Set DE 101: Reserved 110: Reserved 111: Reserved PADJ Busy 0: Phase Adjustment function idle 1: Phase Adjustment in progress AUTO ADJUST REGISTERS 0x50 Phase ADJ CMD FN, (0x00) 0x51 Phase ADJ STATUS, (read only) 19 2:0 7 FN6164.2 September 19, 2007 ISL51002 Register Listing (Continued) ADDRESS 0x52 REGISTER (DEFAULT VALUE) BITS Phase ADJ MASK V, (0x01) 2:0 3 FUNCTION NAME PADJ Exclude v2 DESCRIPTION Vertical line mask: How many lines to exclude before the leading edge of VSYNC 000: 0 lines 001: 1 lines (default) 010: 2 lines 011: 4 lines 100: 6 lines 101: 8 lines 110: 10 lines 111: 12 lines N/A 6:4 PADJ Exclude v1 Choose how many lines to exclude after the leading edge of VSYNC (typically used to exclude VBI data) 000: 5 lines (default) 001: 18 lines 010: 19 lines (480i) 011: 20 lines (1080i) 100: 22 lines (576i) 101: 25 lines (720p) 110: 41 lines (480p/1080p) 111: 44 lines (576p) 0x53 Horizontal pixel mask 1, (0x01) 7:0 PADJ Exclude h1 If a value of ‘N’ is programmed in this register, 2*N pixels after the active edge of HSOUT will be excluded from data collection. Must be >0 for proper operation. 0x54 Horizontal pixel mask 2, (0x01) 7:0 PADJ Exclude h2 If a value of ‘N’ is programmed in this register, 2*N pixels before the active edge of HSOUT will be excluded from data collection. Must be >0 for proper operation. 0x55 Phase Adjust Command Options, (0x20) 0 PADJ Blue Disable Enable/disable blue color for measurement 0: enable 1: disable 1 PADJ Green Disable Enable/disable green color for measurement 0: enable 1: disable 2 PADJ Red Disable Enable/disable red color for measurement 0: enable 1: disable 3 PADJ Adjust Search Option Search option for auto phase adjustment 0: best phase 1: worst phase 4 PADJ Adjust Speed This is a hidden bit for customers. It decides whether the search steps are 28 (fast) or 64 VSYNC intervals (slow). 0: 28 VSYNCs 1: 64 VSYNCs 5 Update Phase on VSYNC 0: phase updated immediately 1: phase updated on VSYNC (default) 6 PADJ Soft Reset 0: Normal operation 1: Reset all phase adjust state machines Take high then low to reset phase adjust block 7 Reserved Set to 0 20 FN6164.2 September 19, 2007 ISL51002 Register Listing (Continued) REGISTER (DEFAULT VALUE) BITS 0x56 Transition threshold, (0x0A) 7:0 PADJ Threshold Threshold of transitions visible for capturing. These are the 8 MSBs of the 10-bit threshold word used for phase quality measurements. The actual 10-bit threshold used equals the value in this register times 4. 0x57 Phase Adjust Data 3, (read only) 7:0 Reserved Reserved 0x58 Phase Adjust Data 2, (read only) 7:0 Reserved Reserved 0x59 Phase Adjust Data 1, (read only) 7:0 Reserved Reserved 0x5A Phase Adjust Data 0, (read only) 7:0 Reserved Reserved 0x60 AFE CTRL, (0x00) 0 Reserved Set to 0 1 700mV calibration 0: Normal operation 1: All three inputs connected to internal ~700mV reference voltage 2 Coast Clamp Enable 0: DC restore clamping and ABLC suspended during Coast and Macrovision (default) 1: DC restore clamping and ABLC continue during Coast 3 Reserved Set to 0 4 Blue Midscale 0: Half scale analog shift not added to Blue Channel (UV) 1: Half scale analog shift added to Blue Channel (YRGB) 5 Green Midscale 0: Half scale analog shift not added to Green Channel (UV) 1: Half scale analog shift added to Green Channel (YRGB) 6 Red Midscale 0: Half scale analog shift not added to Red Channel (UV) 1: Half scale analog shift added to Red Channel (YRGB) 7 Midscale Override 0: Midscale determined by RGB/YUV bit in User Control section – settings in 0x60[6:4] are ignored (default). 1: Midscale determined by 0x60[6:4] 0 Dither Enable 0: Dither disabled (default) 1: Dither enabled 1 Dither Amplitude 0: 16 LSBs (default) 1: 8 LSBs 3:2 Dither Increment 00: Every Pixel (default) 01: Every HSYNC 10 and 11: Every VSYNC Dither Seed Reset Set to 1 and then to 0 to reset ADDRESS 0x61 ADC CTRL, (0x00) 4 21 FUNCTION NAME DESCRIPTION FN6164.2 September 19, 2007 ISL51002 Technical Highlights DPLL drift, the temperature inside a monitor or projector can easily change +50°C between power-on/offset calibration on a cold morning and the temperature reached once the monitor and the monitor's environment have reached steady state. Offset can drift significantly over +50°C, reducing image quality and requiring that the user do a manual calibration once the monitor has warmed up. All video AFEs must phase lock to an HSYNC signal, supplied either directly or embedded in the video stream (Sync On Green). Historically this has been implemented as a traditional analog PLL. At SXGA and lower resolutions, an analog PLL solution has proven adequate, if somewhat troublesome (due to the need to adjust charge pump currents, VCO ranges and other parameters to find the optimum trade-off for a wide range of pixel rates). In addition to drift, many AFEs exhibit interaction between the offset and gain controls. When the gain is changed, the magnitude of the offset is changed as well. This again increases the complexity of the firmware as it tries to optimize gain and offset settings for a given video input signal. Instead of adjusting just the offset, then the gain, both have to be adjusted interactively until the desired ADC output is reached. As display resolutions and refresh rates have increased, however, the pixel period has shrunk. An XGA pixel at a 60Hz refresh rate has 15.4ns to change and settle to its new value. But at UXGA 75Hz, the pixel period is 4.9ns. Most consumer graphics cards (even the ones with “350MHz” DACs) spend most of that time slewing to the new pixel value. The pixel may settle to its final value with 1ns or less before it begins slewing to the next pixel. In many cases it rings and never settles at all. So precision, low-jitter sampling is a fundamental requirement at these speeds, and a difficult one for an analog PLL to meet. The ISL51002 simplifies offset and gain adjustment and completely eliminates offset drift using its Automatic Black Level Compensation (ABLC™) function. ABLC™ monitors the black level and continuously adjusts the ISL51002's 10-bit offset DACs to null out the offset. Any offset, whether due to the video source or the ISL51002's analog amplifiers, is eliminated with 10-bit accuracy. Any drift is compensated for well before it can have a visible effect. Manual offset adjustment control is still available (a 10-bit register allows the firmware to adjust the offset ±64 codes in exactly 1ADC LSB increments). Gain is now completely independent of offset (adjusting the gain no longer affects the offset, so there is no longer a need to program the firmware to cope with interactive offset and gain controls). The ISL51002 provides all the features of traditional triple channel video AFEs, but adds several next-generation enhancements, bringing performance and ease of use to new levels. The ISL51002's DPLL has less than 250ps of jitter, peak to peak, and independent of the pixel rate. The DPLL generates 64 phase steps per pixel (vs. the industry standard 32), for fine, accurate positioning of the sampling point. The crystallocked NCO inside the DPLL completely eliminates drift due to charge pump leakage, so there is inherently no frequency or phase change across a line. An intelligent all-digital loop filter/controller eliminates the need for the user to have to program or change anything (except for the number of pixels) to lock over a range from interlaced video (10MHz or higher) to UXGA 60Hz (165MHz, with the ISL51002-165). The DPLL eliminates much of the performance limitations and complexity associated with noise-free digitization of high speed signals. Automatic Black Level Compensation (ABLC™) and Gain Control Traditional video AFEs have an offset DAC prior to the ADC, to both correct for offsets on the incoming video signals and add/subtract an offset for user “brightness control” without sacrificing the 10-bit dynamic range of the ADC. This solution is adequate, but it places significant requirements on the system's firmware, which must execute a loop that detects the black portion of the signal and then servos the offset DACs until that offset is nulled (or produces the desired ADC output code). Once this has been accomplished, the offset (both the offset in the AFE and the offset of the video card generating the signal) is subject to 22 Finally, there should be no concerns over ABLC™ itself introducing visible artifacts; it doesn't. ABLC™ functions at a very low frequency, changing the offset in 1 LSB increments, so it can't cause visible brightness fluctuations. And once ABLC™ is locked, if the offset doesn't drift, the DACs won't change. If desired, ABLC™ can be disabled, allowing the firmware to work in the traditional way, with 10-bit offset DACs under the firmware's control. Gain and Offset Control To simplify image optimization algorithms, the ISL51002 features fully-independent gain and offset adjustment. Changing the gain does not affect the DC offset, and the weight of an Offset DAC LSB does not vary depending on the gain setting. The full-scale gain is set in the three sets of registers (0x12 and 0x13 - 0x16 and 0x17). Each set of gain registers is divided into an 8-bit MSB register (0x12, 0x14 and 0x16) and a 2-bit LSB register providing a 10-bit gain value that both allows for 8-bit control compatible with the 8-bit family of AFEs and allows for the expansion of the gain resolution in future AFEs without significant firmware changes. The ISL51002 can accept input signals with amplitudes ranging from 0.35VP-P to 1.4VP-P. FN6164.2 September 19, 2007 ISL51002 The offset controls shift the entire RGB input range, changing the input image brightness. Three separate registers provide independent control of the R, G, and B channels. Their nominal setting is 0x8000, which forces the ADC to output code 0x0000 (or 0x200 for the R (Pr) and B (Pb) channels in YPbPr mode) during the back porch period when ABLC™ is enabled. TABLE 2. YUV MAPPING (4:2:2) INPUT SIGNAL ISL51002 INPUT CHANNEL ISL51002 OUTPUT ASSIGNMENT OUTPUT SIGNAL Y Green Green Y0Y1Y2Y3 Pb Blue Blue Driven Low Pr Red Red U0V0U2V2 Functional Description RGB to YUV Color Space Converter (CSC) Inputs The ISL51002 digitizes analog video inputs in both RGB and Component (YPbPr) formats, with or without embedded sync (SOG). RGB Inputs For RGB inputs, the internal Color Space Converter, when enabled (register 0x28-bit [6] = 1), will convert from the RGB color space to the YUV (YCbCr) color space using the following conversion formulas: Y = 0.299R + 0.587G + 0.114B For RGB inputs, the black/blank levels are identical and equal to 0V. The range for each color is typically 0V to 0.7V from black to white. HSYNC and VSYNC are separate signals. U = -0.172R - 0.339G + 0.511B + 512 Component YPbPr Inputs Input Coupling In addition to RGB and RGB with SOG, the ISL51002 has an option that is compatible with the component YPbPr video inputs typically generated by DVD players. While the ISL51002 digitizes signals in these color spaces, it can only perform color space conversion from RGB to YUV; if it digitizes an RGB signal, it outputs digital RGB or YUV, while if it digitizes a YPbPr signal, it outputs digital YCbCr, also called YUV. Inputs can be either AC-coupled (default) or DC-coupled (See register 0x10[3]). AC coupling is usually preferred since it allows video signals with substantial DC offsets to be accurately digitized. The ISL51002 provides a complete internal DC-restore function, including the DC restore clamp (See Figure 1) and programmable clamp timing (registers 0x24, 0x25, and 0x26). The Luminance (Y) signal is applied to the Green Channel and is processed in a manner identical to the Green input with SOG described previously. The color difference signals Pb and Pr are bipolar and swing both above and below the black level. When the YPbPr mode is enabled, the black level output for the color difference channels shifts to a mid scale value of 0x200. Setting configuration register 0x10[4] = 1 enables the YPbPr signal processing mode of operation. TABLE 1. YUV MAPPING (4:4:4) INPUT SIGNAL ISL51002 INPUT CHANNEL ISL51002 OUTPUT ASSIGNMENT OUTPUT SIGNAL Y Green Green Y0Y1Y2Y3 Pb Blue Blue U0U1U2U3 Pr Red Red V0V1V2V3 The ISL51002 can optionally decimate the incoming data to provide a 4:2:2 output stream (configuration register 0x28[0] = 1) as shown in Table 2. V = 0.511R - 0.428G - 0.083B + 512 When AC-coupled, the DC restore clamp is applied every line, a programmable number of pixels after the trailing edge of HSYNC. If register 0x60[2] = 0 (the default), the clamp will not be applied while the DPLL is coasting, preventing any clamp voltage errors from composite sync edges, equalization pulses, or Macrovision signals. After the trailing edge of HSYNC, the DC restore clamp is turned on after the number of pixels specified in the DC Restore and ABLC™ Starting Pixel registers (0x24 and 0x25) has been reached. The clamp is applied for the number of pixels specified by the DC Restore Clamp Width Register (0x26). The clamp can be applied to the back porch of the video, or to the front porch (by increasing the DC Restore and ABLC™ Starting Pixel registers so all the active video pixels are skipped). Note: The TriLevel detect for Sync on Green (SOG) utilizes the digitized data from the selected Green video channel. If TriLevel Sync is present, the default DC Clamp start position will clamp at the top of the TriLevel Sync pulse giving a false negative for TriLevel detect and clamping off the bottom half of the green video. If you have an indication of active SOG you must move the clamp start to a value greater than 0x30 to check to see if the Tri-level Sync is present. If DC-coupled operation is desired, the input to the ADC will be the difference between the input signal (RIN1, for example) and that channel’s ground reference (RGBGND1 in that example). 23 FN6164.2 September 19, 2007 ISL51002 AUTOMATIC BLACK LEVEL COMPENSATION (ABLC™) LOOP DC RESTORATION DC RESTORE CLAMP DAC R(GB)IN0 R(GB)GND0 VCLAMP CLAMP GENERATION TO ABLC BLOCK VGA0 OFFSET DAC 10 OFFSET CONTROL REGISTERS FIXED 10 OFFSET 10 ABLC™ ABLC™ 0X000 10 10 ABLC™ R(GB)IN1 R(GB)GND1 VGA1 VIN+ VIN- R(GB)IN2 R(GB)GND2 VGA2 R(GB)IN3 R(GB)GND3 VGA3 FIXED OFFSET 10 PGA INPUT BANDWIDTH 10-BIT ADC 10 10 TO OUTPUT FORMATTER BANDWIDTH CONTROL FIGURE 1. VIDEO FLOW (INCLUDING ABLC™) SOG Macrovision For component YPbPr signals, the sync signal is embedded on the Y-Channel’s video, which is connected to the green input, hence the name SOG (Sync on Green). The horizontal sync information is encoded onto the video input by adding the sync tip during the blanking interval. The sync tip level is typically 0.3V below the video black level. The ISL51002 automatically detects the presense of Macrovision-encoded video. When Macrovision is detected, it generates a mask signal that is ANDed with the incoming SOG CSYNC signal to remove the Macrovision before the HSYNC goes to the PLL. No additional programming is required to support Macrovision. To minimize the loading on the green channel, the SOG input for each of the green channels should be AC-coupled to the ISL51002 through a series combination of a 10nF capacitor and a 500Ω resistor. The mask signal is also applied to the HSYNCOUT signal. When Sync Mask Disable = 0, any Macrovision present on the incoming sync will not be visible on HSYNCOUT. If the application requires the Macrovision pulses to be visible on HSYNCOUT, set the HSYNCOUT Mask Disable bit (register 0x7A-bit 4). SOG Slicer (Figure 2) The SOG input has programmable threshold, 40mV of hysteresis, and an optional low pass filter than can be used to remove high frequency video spikes (generated by overzealous video peaking in a DVD player, for example) that can cause false SOG triggers. The SOG threshold sets the comparator threshold relative to the sync tip (the bottom of the SOG pulse). Inside the ISL51002, a 1µA pulldown ensures that each sync tip triggersthe clamp circuit causing the tip to be clamped to a 600mV level. A comparator compares the SOG signal with an internal 4-bit programmable threshold level reference ranging from 0mV to 300mV above the sync clamp level. The SOG threshold level, hysteresis, and low-pass filter is programmed via registers 0x30and 0x31. If the Sync-On-Green function is not needed, the SOGIN pin(s) may be left unconnected. SYNC Processing The ISL51002 can process sync signals from 3 different sources: discrete HSYNC and VSYNC, composite sync on the HSYNC input, or composite sync from a Sync-On-Green (SOG) signal embedded on the Green video input. The ISL51002 has SYNC activity detect functions to help the firmware determine which sync source is available. 24 Headswitching from Analog Videotape Signals Occasionally this AFE may be used to digitize signals coming from analog videotape sources. The most common example of this is a Digital VCR (which for best signal quality would be connected to this AFE with a component YPbPr connection). If the digital VCR is playing an older analog VHS tape, the sync signals from the VCR may contain the worst of the traditional analog tape artifacts: headswitching. Headswitching is traditionally the enemy of PLLs with large capture ranges, because a headswitch can cause the HSYNC period to change by as much as ±90%. To the PLL, this can look like a frequency change of -50% to +900%, causing errors in the output frequency (and obviously the phase) to change. Subsequent HSYNCs have the correct, original period, but most analog PLLs will take dozens of lines to settle back to the correct frequency and phase after a headswitch disturbance. This causes the top of the image to “tear” during normal playback. In “trick modes” (fast forward and rewind), the HSYNC signal has multiple headswitch-like discontinuities, and many PLLs never settle to the correct value before the next headswitch, rendering the image completely unintelligible. FN6164.2 September 19, 2007 ISL51002 SLICER DAC 600mV TO 900mV CLAMP 600mV + – 10nF + - 4 SLICE - 500 Ω SYNCOUT GREEN + C IN SOG IN R IN 1µA FILTER ON/OFF HIST ON/OFF FIGURE 2. SOG SLICER Intersil’s DPLL has the capability to correct large phase changes almost instantly by maximizing the phase error gain while keeping the frequency gain relatively low. This is done by changing the contents of register 0x74 to 0x4C. This increases the phase error gain to 100%. Because a phase setting this high will slightly increase jitter, the default setting (0x49) for register 0x74 is recommended for all other sync sources. SYNC Timing Measurement The ISL51002 analyzes the timing characteristics of the sysnc signals for the currently selected input channel and presents the results in registers 0x40 through 0x0x46. The HSYNC period and pulse width values are 16-bit numbers representing the number of crystal clocks in 16 consecutive periods or pulse widths giving a measurment resolution of 1/16th of a crystal clock. The VSYNC period is a 12-bit number representing the number of either HSYNCs or units of 512 crystal clocks that occure in one video frame. The default is to count HSYNC pulses but setting register 0x4F[0] = 1 changes to the units to crystal clock ÷ 512. The VSYNC pulse width is a 12-bit number representing the number of either HSYNCs or units of 512 crystal clocks that occure in one VSYNC. The default is to count HSYNC pulses but setting register 0x4F[0] = 1 changes to the units to crystal clock ÷ 512. PGA The ISL51002’s Programmable Gain Amplifier (PGA) has a nominal gain range from 0.5V/V (-6dB) to 2.0V/V (+6dB). The transfer function is: V GainCode Gain ⎛ ----⎞ = 0.5 + ----------------------------⎝ V⎠ 170 25 (EQ. 1) where GainCode is the value in the Gain register for that particular color. Note that for a gain of 1V/V, the GainCode should be 85 (0x55). This is a different center value than the 128 (0x80) value used by some other AFEs, so the firmware should take this into account when adjusting gains. The PGAs are updated by the internal clamp signal once per line. In normal operation this means that there is a maximum delay of one HSYNC period between a write to a Gain register for a particular color and the corresponding change in that channel’s actual PGA gain. If there is no regular HSYNC/SOG source, or if the external clamp option is enabled (register 0x10[7:6]) but there is no external clamp signal being generated, it may take up to 100ms for a write to the Gain register to update the PGA. This is not an issue in normal operation with RGB and YPbPr signals. Offset DAC The ISL51002 features a 10-bit Digital-to-Analog Converter (DAC) to provide extremely fine control over the full channel offset. The DAC is placed after the PGA to eliminate interaction between the PGA (controlling “contrast”) and the Offset DAC (controlling “brightness”). In normal operation, the Offset DAC is controlled by the ABLC™ circuit, ensuring that the offset is always reduced to sub-LSB levels (See the following ABLC™ section for more information). When ABLC™ is enabled, the Offset register pairs (0x18 and 0x19 through 0x1C and 0x1D) control a digital offset added to or subtracted from the output of the ADC. This mode provides the best image quality and eliminates the need for any offset calibration. If desired, ABLC™ can be disabled (0x27[0] = 1) and the Offset DAC programmed manually, with the 8 most significant bits in registers 0x18, 0x1A,10x1C, and the 2 least significant bits in registers 0x19[7:6], 0x1B[7:6] and 0x1D[7:6]. FN6164.2 September 19, 2007 ISL51002 The default Offset DAC range is ±127 ADC LSBs. Setting 0x27[1] = 1 reduces the swing of the Offset DAC by 50%, making 1 Offset DAC LSB the weight of 1/2 of an ADC LSB. This provides the finest offset control and applies to both ABLC™ and manual modes. Automatic Black Level Compensation (ABLC™) ABLC is a function that continuously removes all offset errors from the incoming video signal by monitoring the offset at the output of the ADC and servoing the 10-bit analog DAC to force those errors to zero. When ABLC is enabled, the user offset control is a digital adder, with 10-bit resolution. When the ABLC function is enabled (0x27[0] = 0), the ABLC function is executed every line after the trailing edge of HSYNC. If register 0x60[2] = 0 (the default), the ABLC function will be not be triggered while the DPLL is coasting, preventing any composite sync edges, equalization pulses, or Macrovision signals from corrupting the black data and potentially adding a small error in the ABLC accumulator. After the trailing edge of HSYNC, the start of ABLC is delayed by the number of pixels specified in registers 0x24 and 0x25. After that delay, the number of pixels specified by register 0x27[3:2] are averaged together and added to the ABLC’s accumulator. The accumulator stores the average black levels for the number of lines specified by register 0x27[6:4], which is then used to generate a 10-bit DAC value. The ABLC can be set to allow the capture of signals below black by setting registers 0x65, 0x66 and 0x67 to a number that will controll the target for the ABLC servo loop. If you set register 0x65 to 0x04 then the ABLC will adjust the offset dac to produce an average output code on the Red channel of 0x10 during the back porch. Effectivly, the black level for a given channel will be set to the value of its ABLC offset target register times four. (output = register 0x65, 0x66 or 0x67 times 4). ADC The ISL51002 features 3 fully differential, high-speed 10-bit ADCs. Clock Generation A Digital Phase Lock Loop (DPLL) is employed to generate the pixel clock frequency. The HSYNC input and the external XTAL provide a reference frequency to the PLL. The PLL then generates the pixel clock frequency that equal to the incoming HSYNC frequency times the HTOTAL value programmed into registers 0x1E and 0x1F. The stability of the clock is very important and correlates directly with the quality of the image. During each pixel time transition, there is a small window where the signal is slewing from the old pixel amplitude and settling to the new pixel value. At higher frequencies, the pixel time transitions at a faster rate, which makes the stable pixel time even 26 smaller. Any jitter in the pixel clock reduces the effective stable pixel time and thus the sample window in which pixel sampling can be made accurately. Sampling Phase The ISL51002 provides 64 low-jitter phase choices per pixel period, allowing the firmware to precisely select the optimum sampling point. The sampling phase register is 0x20. Auto Phase Adjust The ISL51002 provides the ability to automatically adjust the Sampling Phase to the best setting. Set register 0x50 to 0x03 to activate the auto phase adjust function. Data Enable (DE) Generator The ISL51002 provides a signal that is high during the active video time when properly configured. This signal is used by devices such as DVI/HDMI transmitters to gate the active portion of the video and ignore the H and V sync times. Auto DE Adjust The ISL51002 provides the ability to automatically adjust the DE to the settings that are very close to ideal. The determination of exactly where on a line the active video starts and ends depends heavily on the video content being analyzed making the DE settings difficult to automate. The customer will be required to fine tune the DE settings after the Auto Adjust routine has completed. Set register 0x50 to 0x04 to activate the auto DE adjust function HSYNC Slicer To further minimize jitter, the HSYNC inputs are treated as analog signals, and brought into a precision slicer block with thresholds programmable in 400mV steps with 240mV of hysteresis, and a subsequent digital glitch filter that ignores any HSYNC transitions within 100ns of the initial transition. This processing greatly increases the AFE’s rejection of ringing and reflections on the HSYNC line and allows the AFE to perform well even with pathological HSYNC signals. Voltages given above and in the HSYNC Slicer register description are with respect to a 3.3V sync signal at the HSYNCIN input pin. To achieve 5V compatibility, a 680Ω series resistor should be placed between the HSYNC source and the HSYNCIN input pin. Relative to a 5V input, the hysteresis will be 240mV*5V/3.3V = 360mV, and the slicer step size will be 400mV*5V/3.3V = 600mV per step. SYNC Status and Polarity Detection The CH0 and CH1 Activity Status register (0x02) and the CH2 and CH3 Activity Status register (0x03) continuously monitor all 12sync inputs (VSYNCIN, HSYNCIN, and SOGIN for each of 4 channels) and report their status, while the Selected Input Channel Characteristics register (0x01) gives more detailed information on the curently selected input channel. However, accurate sync activity detection is always a challenge. Noise and repetitive video patterns on the Green FN6164.2 September 19, 2007 ISL51002 channel may look like SOG activity when there actually is no SOG signal, while non-standard SOG signals and TriLevel sync signals may have amplitudes below the default SOG slicer levels and not be easily detected. As a consequence, not all of the activity detect bits in the ISL51002 are correct under all conditions. For best SOG operation, the SOG low pass filter (register 0x04[4] should always be enabled to reject the high frequency peaking often seen on video signals. HSYNC and VSYNC Activity Detect Activity on these bits always indicates valid sync pulses, so they should have the highest priority and be used even if the SOG activity bit is also set. SOG Activity Detect The SOG activity detect bit monitors the output of the SOG slicer, looking for 64 consecutive pulses with the same period and duty cycle. If there is no signal on the Green (or Y) Channel, the SOG slicer will clamp the video to a DC level and will reject any sporadic noise. There should be no false positive SOG detects if there is no video on Green (or Y) Channel. If there is video on Green (or Y) Channel with no valid SOG signal, the SOG activity detect bit may sometimes report false positives (it will detect SOG when no SOG is actually present). This is due to the presence of video with a repetitive pattern that creates a waveform similar to SOG. For example, the desktop of a PC operating system is black during the front porch, horizontal sync, and back porch, then increases to a larger value for the video portion of the screen. This creates a repetitive video waveform very similar to SOG that may falsely trigger the SOG Activity detect bit. However, in these cases where there is active video without SOG, the SYNC information will be provided either as separate H and V sync on HSYNCIN and VSYNCIN, or composite sync on HSYNCIN. HSYNCIN and VSYNCIN should therefore be used to qualify SOG. The SOG Active bit should only be considered valid if HSYNC Activity Detect = 0. Note: Some pattern generators can output HSYNC and SOG simultaneously, in which case both the HSYNC and the SOG activity bits will be set, and valid. Even in this case, however, the monitor should still choose HSYNC over SOG. TriLevel Sync Detect The TriLevel detect for Sync on Green (SOG) utilizes the digitized data from the selected Green video channel. If TriLevel Sync is present, the default DC Clamp start position will clamp at the top of the TriLevel Sync pulse giving a false negative for TriLevel detect and clamping off the bottom half of the green video. If you have an indication of active SOG you must move the clamp start to a value greater than 0x30 to check to see if the TriLevel Sync is present. 27 SYNC Output Signals The ISL51002 has a pair of HSYNC output signals, HSYNCOUT and VSYNCOUT, and HSOUT. HSYNCOUT and VSYNCOUT are buffered versions of the incoming sync signals; no synchronization is done. These signals are used for mode detection HSOUT is generated by the ISL51002’s logic and is synchronized to the output DATACLK and the digital pixel data on the output databus. HSOUT is used to signal the start of a new line of digital data. Both HSYNCOUT and VSYNCOUT (including the sync separator function) remain active in power-down mode. This allows them to be used in conjunction with the Sync Status registers to detect valid video without powering up the ISL51002. HSYNCOUT HSYNCOUT is an unmodified, buffered version of the incoming HSYNCIN or SOGIN signal of the selected channel, with the incoming signal’s period, polarity, and width to aid in mode detection. HSYNCOUT will be the same format as the incoming sync signal: either horizontal or composite sync. If a SOG input is selected, HSYNCOUT will output the entire SOG signal, including the VSYNC portion, pre-/post-equalization pulses if present, and Macrovision pulses if present. HSYNCOUT remains active when the ISL51002 is in power-down mode. HSYNCOUT is generally used for mode detection. VSYNCOUT VSYNCOUT is an unmodified, buffered version of the incoming VSYNCIN signal of the selected channel, with the original VSYNC period, polarity, and width to aid in mode detection. If a SOG input is selected, this signal will output the VSYNC signal extracted by the ISL51002’s sync slicer. Extracted VSYNC will be the width of the embedded VSYNC pulse plus pre- and postequalization pulses (if present). Macrovision pulses from an NTSC DVD source will lengthen the width of the VSYNC pulse. Macrovision pulses from other sources (PAL DVD or videotape) may appear as a second VSYNC pulse encompassing the width of the Macrovision. See the Macrovision section for more information. VSYNCOUT (including the sync separator function) remains active in power-down mode. VSYNCOUT is generally used for mode detection, start of field detection, and even/odd field detection. HSOUT HSOUT is generated by the ISL51002’s control logic and is synchronized to the output DATACLK and the digital pixel data on the output databus. Its trailing edge is aligned with pixel 0. Its width, in units of pixels, is determined by register 0x2A, and its polarity is determined by register 0x29[3]. As the width is increased, the trailing edge stays aligned with pixel 0, while the leading edge is moved backwards in time relative to pixel 0. HSOUT is used by the scaler to signal the start of a new line of pixels. FN6164.2 September 19, 2007 ISL51002 Crystal Oscillator Initialization An external 12MHz to 27MHz crystal supplies the low-jitter reference clock to the DPLL. The absolute frequency of this crystal within this range is unimportant, as is the crystal’s temperature coefficient, allowing use of less expensive, lower-grade crystals. The ISL51002 initializes with default register settings for an AC-coupled, RGB input on the VGA1 channel, with a 30-bit output. As an alternative to a crystal, the XTALIN pin can be driven with a 3.3V CMOS-level external clock source at any frequency between 12MHz and 27MHz. The ISL51002’s jitter specification assumes a low-jitter crystal source. If the external clock source has increased jitter, the sample clock generated by the DPLL may exhibit increased jitter as well. EMI Considerations There are two possible sources of EMI on the ISL51002: Reset The ISL51002 has a Power On Reset (POR) function that resets the chip to its default state when power is initially applied, including resetting all the registers to their default settings as described in the Register Listing. The POR function takes 512k Crystal clocks (~21ms at 25MHz) to complete. The external RESET pin duplicates the reset function of the POR without having to cycle the power supplies. The RESET pin does not need to be used in normal operation and can be tied high. CRYSTAL OSCILLATOR ISL51002 Serial Communication The EMI from the crystal oscillator is negligible. This is due to an amplitude-regulated, low voltage sine wave oscillator circuit, instead of the typical high-gain square wave inverter-type oscillator, so there are no harmonics. The crystal oscillator is not a significant source of EMI. Overview DIGITAL OUTPUT SWITCHING This is the largest potential source of EMI. However, the EMI is determined by the PCB layout and the loading on the databus. The way to control this is to put series resistors on the output of all the digital pins (as our demo board and reference circuits show). These resistors should be as large as possible, while still meeting the setup and hold timing requirements of the scaler. We recommend starting with 22Ω. If the databus is heavily loaded (long traces, many other part on the same bus), this value may need to be reduced. If the databus is lightly loaded, it may be increased. Intersil’s recommendations to minimize EMI are: • Minimize the databus trace length • Minimize the databus capacitive loading. If EMI is a problem in the final design, increase the value of the digital output series resistors to reduce slew rates on the bus. This can only be done as long as the scaler’s setup and hold timing requirements continue to be met. Standby Mode The ISL51002 can be placed into a low power standby mode by writing a 0x0F to register 0x2C, powering down the triple ADCs, the DPLL, and most of the internal clocks. To allow input monitoring and mode detection during powerdown, the following blocks remain active: • Serial interface (including the crystal oscillator) to enable register read/write activity The ISL51002 uses a 2-wire serial bus for communication with its host. SCL is the Serial Clock line, driven by the host, and SDA is the Serial Data line, which can be driven by all devices on the bus. SDA is open drain to allow multiple devices to share the same bus simultaneously. Communication is accomplished in three steps: 1. The Host selects the ISL51002 it wishes to communicate with. 2. The Host writes the initial ISL51002 Configuration Register address it wishes to write to or read from. 3. The Host writes to or reads from the ISL51002’s Configuration Register. The ISL51002’s internal address pointer auto increments, so to read registers 0x00 through 0x1B, for example, one would write 0x00 in step 2, then repeat step three 28 times, with each read returning the next register value. The ISL51002 has a 7-bit address on the serial bus. The upper 6-bits are permanently set to 100110, with the lower bit determined by the state of pin 67. This allows two ISL51002s to be independently controlled while sharing the same bus. The bus is nominally inactive, with SDA and SCL high. Communication begins when the host issues a START command by taking SDA low while SCL is high (Figure 3). The ISL51002 continuously monitors the SDA and SCL lines for the start condition and will not respond to any command until this condition has been met. The host then transmits the 7-bit serial address plus a R/W bit, indicating if the next transaction will be a Read (R/W = 1) or a Write (R/W = 0). If the address transmitted matches that of any device on the bus, that device must respond with an ACKNOWLEDGE (Figure 4). • Activity and polarity detect functions (registers 0x01 and 0x02) • The HSYNCOUT and VSYNCOUT pins (for mode detection) 28 FN6164.2 September 19, 2007 ISL51002 Once the serial address has been transmitted and acknowledged, one or more bytes of information can be written to or read from the slave. Communication with the selected device in the selected direction (read or write) is ended by a STOP command, where SDA rises while SCL is high (Figure 3), or a second START command, which is commonly used to reverse data direction without relinquishing the bus. Data on the serial bus must be valid for the entire time SCL is high (Figure 5). To achieve this, data being written to the ISL51002 is latched on a delayed version of the rising edge of SCL. SCL is delayed and deglitched inside the ISL51002 for three crystal clock periods (120ns for a 25MHz crystal) to eliminate spurious clock pulses that could disrupt serial communication. When the contents of the ISL51002 are being read, the SDA line is updated after the falling edge of SCL, delayed and deglitched in the same manner. Configuration Register Write Figure 6 shows two views of the steps necessary to write one or more words to the Configuration Register. Configuration Register Read Figure 7 shows two views of the steps necessary to read one or more words from the Configuration Register. SCL SDA START STOP FIGURE 3. VALID START AND STOP CONDITIONS SCL FROM HOST 1 8 9 DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER START ACKNOWLEDGE FIGURE 4. ACKNOWLEDGE RESPONSE FROM RECEIVER SCL SDA DATA STABLE DATA CHANGE DATA STABLE FIGURE 5. VALID DATA CHANGES ON THE SDA BUS 29 FN6164.2 September 19, 2007 ISL51002 Signals the beginning of serial I/O START COMMAND ISL51002 SERIAL BUS ADDRESS R/W A 0 ISL51002 Serial Bus Address Write This is the 7-bit address of the ISL51002 on the 2-wire bus. The address is 0x98 if pin 67 is low, 0x9A if pin 67 is high. Shift this value left to when adding the R/W bit. 0 1 0 0 1 1 A7 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 (PIN 67) ISL51002 Register Address Write This is the address of the ISL51002’s configuration register that the following byte will be written to. ISL51002 Register Data Write(s) This is the data to be written to the ISL51002’s configuration register. Note: The ISL51002’s Configuration Register’s address pointer auto increments after each data write: repeat this step to write multiple sequential bytes of data to the Configuration Register. (REPEAT IF DESIRED) Signals the ending of serial I/O STOP COMMAND SIGNALS FROM THE HOST SDA BUS S T A SERIAL BUS R ADDRESS T REGISTER ADDRESS 1 0 0 1 1 0A0 aaaaaaaa A C K SIGNALS FROM THE ISL51002 S T O P DATA WRITE* * The data write step may be repeated to write to the ISL51002’s Configuration Register sequentially, beginning at the Register Address written in the previous step. dddddddd A C K A C K FIGURE 6. CONFIGURATION REGISTER WRITE 30 FN6164.2 September 19, 2007 ISL51002 Signals the beginning of serial I/O START COMMAND ISL51002 SERIAL BUS ADDRESS R/W 0 1 0 0 1 1 A7 A6 A5 A4 A3 A2 A (PIN 67) 0 A1 A0 START COMMAND ISL51002 SERIAL BUS R/W 0 1 0 0 1 1 D7 D6 D5 D4 D3 D2 A (PIN 67) 1 D1 D0 (REPEAT IF DESIRED) SIGNALS FROM THE HOST SDA BUS aaaaaaaa A C K SIGNALS FROM THE ISL51002 R E S T SERIAL BUS A R ADDRESS T REGISTER ADDRESS 1 0 0 1 1 0A0 ISL51002 Register Address Write This sets the initial address of the ISL51002’s configuration register for subsequent reading. Ends the previous transaction and starts a new one ISL51002 Serial Bus Address Write This is the 7-bit address of the ISL51002 on the 2-wire bus. The address is 0x98 if pin 67 is low, 0x9A if pin 67 is high. R/W = 1, indicating next transaction(s) will be a read. ISL51002 Register Data Read(s) This is the data read from the ISL51002’s configuration register. Note: The ISL51002’s Configuration Register’s address pointer auto increments after each data read: repeat this step to read multiple sequential bytes of data from the Configuration Register. Signals the ending of serial I/O STOP COMMAND S T SERIAL BUS A R ADDRESS T ISL51002 Serial Bus Address Write This is the 7-bit address of the ISL51002 on the 2-wire bus. The address is 0x98 if pin 67 is low, 0x9A if pin 67 is high. R/W = 0, indicating next transaction will be a write. DATA READ* 1 0 0 1 1 0A1 A C K S T O AP C K * The data read step may be repeated to read from the ISL51002’s Configuration Register sequentially, beginning at the Register Address written in the two steps previous. Adddddddd C K FIGURE 7. CONFIGURATION REGISTER READ 31 FN6164.2 September 19, 2007 ISL51002 Metric Plastic Quad Flatpack Packages (MQFP) D MDP0055 D1 14x20mm 128 LEAD MQFP (WITH AND WITHOUT HEAT SPREADER) 3.2mm FOOTPRINT 128 PIN 1 ID 1 DIMENSIONS (MILLIMETERS) A Max 3.40 20.000 ±0.100 (E1) 19.870 ±0.100 18.500 REF E1 E SYMBOL 12.500 REF C0.600x0.350 (4X) 13.870 ±0.100 A 1 A 14.000 ±0.100 (D1) 12° ALL AROUND Y b T1 T REMARKS Overall height A1 0.250~0.500 Standoff A2 2.750 ±0.250 Package thickness α 0°~7° b 0.220 ±0.050 Foot angle b1 0.200 ±0.030 D 17.200 ±0.250 Lead width 1 Lead base metal width 1 Lead tip to tip D1 14.000 ±0.100 Package length E 23.200 ±0.250 Lead tip to tip E1 20.000 ±0.100 Package width e 0.500 Base Lead pitch L 0.880 ±0.150 Foot length L1 1.600 Ref. Lead length T 0.170 ±0.060 Frame thickness 1 T1 0.152 ±0.040 ccc 0.100 Frame base metal thickness 1 Foot coplanarity ddd 0.100 Foot position Rev. 2 2/07 b1 NOTES: 1 SECTION A-A DROP IN HEAT SPREADER 4 STAND POINTS EXPOSED 1. General tolerance: Distance ±0.100, Angle +2.5°. 2. 1 Matte finish on package body surface except ejection and pin 1 marking (Ra 0.8~2.0um). 3. All molded body sharp corner RADII unless otherwise specified (Max RO.200). 4. Package/Leadframe misalignment (X, Y): Max. 0.127 5. Top/Bottom misalignment (X, Y): Max. 0.127 R0.25 TYP ALL AROUND 6. Drawing does not include plastic or metal protrusion or cutting burr. 0.200 MIN 7. 0° MIN A2 R0.13 MIN ccc C A 2 Compliant to JEDEC MS-022. 0.13~0.30 α SEATING PLANE L e A1 C GAUGE PLANE 0.25 BASE L1 b T ddd M C DETAIL Y All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 32 FN6164.2 September 19, 2007