Samsung K6R1004V1D 64kx16 bit high-speed cmos static ram(3.3v operating) operated at commercial and industrial temperature ranges. Datasheet

PRELIMINARY
PRELIMINARY
for AT&T
K6R1004V1D
CMOS SRAM
Document Title
64Kx16 Bit High-Speed CMOS Static RAM(3.3V Operating)
Operated at Commercial and Industrial Temperature Ranges.
Revision History
Rev. No.
History
Rev. 0.0
Rev. 0.1
Rev. 0.2
Initial document.
Speed bin modify
Current modify
May. 11. 2001
June. 18. 2001
September. 9. 2001
Preliminary
Preliminary
Preliminary
Rev. 1.0
1. Final datasheet release
2. Delete 12ns speed bin.
3. Change Icc for Industrial mode.
Item
Previous
8ns
100mA
ICC(Industrial)
10ns
85mA
December. 18. 2001
Final
Draft Data
Remark
Current
90mA
75mA
Rev. 2.0
1. Delete UB,LB releated timing diagram.
June. 19. 2002
Final
Rev. 3.0
1. Add the Lead Free Package type.
July. 26, 2004
Final
The attached data sheets are prepared and approved by SAMSUNG Electronics. SAMSUNG Electronics CO., LTD. reserve the right to change the
specifications. SAMSUNG Electronics will evaluate and reply to your requests and questions on the parameters of this device. If you have any questions, please contact the SAMSUNG branch office near your office, call or contact Headquarters.
-1-
Rev. 3.0
July 2004
PRELIMINARY
PRELIMINARY
for AT&T
K6R1004V1D
CMOS SRAM
1Mb Async. Fast SRAM Ordering Information
Org.
256K x4
Part Number
K6R1004C1D-J(K)C(I) 10
VDD(V)
Speed ( ns )
5
10
K6R1004V1D-J(K)C(I) 08/10
3.3
8/10
K6R1008C1D-J(K,T,U)C(I) 10
5
10
K6R1008V1D-J(K,T,U)C(I) 08/10
3.3
8/10
K6R1016C1D-J(K,T,U,E)C(I) 10
5
10
3.3
8/10
128K x8
64K x16
K6R1016V1D-J(K,T,U,E)C(I) 08/10
-2-
PKG
Temp. & Power
J : 32-SOJ
K: 32-SOJ(LF)
J : 32-SOJ
K : 32-SOJ(LF)
T : 32-TSOP2
U : 32-TSOP2(LF)
C : Commercial Temperature
,Normal Power Range
I : Industrial Temperature
,Normal Power Range
J : 44-SOJ
K : 44-SOJ(LF)
T : 44-TSOP2
U : 44-TSOP2(LF)
E : 48-TBGA
Rev. 3.0
July 2004
PRELIMINARY
PRELIMINARY
for AT&T
K6R1004V1D
CMOS SRAM
256K x 4 Bit (with OE) High-Speed CMOS Static RAM(3.3V Operating)
FEATURES
GENERAL DESCRIPTION
• Fast Access Time 8,10ns(Max.)
• Low Power Dissipation
Standby (TTL)
: 20mA(Max.)
(CMOS) : 5mA(Max.)
Operating //K6R1004V1D-08: 80mA(Max.)
K6R1004V1D-10: 65mA(Max.)
• Single 3.3±0.3V Power Supply
• TTL Compatible Inputs and Outputs
• Fully Static Operation
- No Clock or Refresh required
• Three State Outputs
• Center Power/Ground Pin Configuration
• Standard Pin Configuration :
K6R1004V1D-J : 32-SOJ-400
K6R1004V1D-K : 32-SOJ-400 (Lead-Free)
• Operating in Commercial and Industrial Temperature range.
The K6R1004V1D is a 1,048,576-bit high-speed Static Random
Access Memory organized as 262,144 words by 4 bits.
The K6R1004V1D uses 4 common input and output lines and
has an output enable pin which operates faster than address
access time at read cycle. The device is fabricated using
SAMSUNG′s advanced CMOS process and designed for
high-speed circuit technology. It is particularly well suited for
use in high-density high-speed system applications. The
K6R1004V1D is packaged in a 400 mil 32-pin plastic SOJ.
PIN CONFIGURATION(Top View)
FUNCTIONAL BLOCK DIAGRAM
A0
A1
A2
A3
A4
A5
A6
A7
A8
I/O1 ~ I/O4
Row Select
Clk Gen.
Data
Cont.
Pre-Charge Circuit
Memory Array
512 Rows
512x4 Columns
I/O Circuit &
Column Select
N.C
1
32 A17
A0
2
31 A16
A1
3
30 A15
A2
4
29 A14
A3
5
28 A13
CS
6
27
I/O1
7
26 I/O4
Vcc
8
Vss
9
25 Vss
SOJ
24 Vcc
I/O2 10
23 I/O3
WE
11
22 A12
A4
12
21
A5
13
20 A10
A6
14
19
A9
A7
15
18
A8
A11
17 N.C
N.C 16
CLK
Gen.
OE
PIN FUNCTION
A9 A10 A11 A12 A13 A14 A15 A16 A17
Pin Name
A0 - A17
CS
WE
OE
Address Inputs
WE
Write Enable
CS
Chip Select
OE
Output Enable
I/O1 ~ I/O4
VCC
-3-
Pin Function
Data Inputs/Outputs
Power(+3.3V)
VSS
Ground
N.C
No Connection
Rev. 3.0
July 2004
PRELIMINARY
PRELIMINARY
for AT&T
K6R1004V1D
CMOS SRAM
ABSOLUTE MAXIMUM RATINGS*
Parameter
Voltage on Any Pin Relative to VSS
Symbol
Rating
Unit
VIN, VOUT
-0.5 to 4.6
V
VCC
-0.5 to 4.6
V
Pd
1
W
Voltage on VCC Supply Relative to VSS
Power Dissipation
TSTG
-65 to 150
°C
Commercial
TA
0 to 70
°C
Industrial
TA
-40 to 85
°C
Storage Temperature
Operating Temperature
* Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect reliability.
RECOMMENDED DC OPERATING CONDITIONS(TA=0 to 70°C)
Parameter
Symbol
Min
Typ
Max
Unit
Supply Voltage
VCC
3.0
3.3
3.6
V
Ground
VSS
0
0
0
V
Input High Voltage
VIH
2.0
-
VCC+0.3**
V
Input Low Voltage
VIL
-0.3*
-
0.8
V
* VIL(Min) = -2.0V a.c (Pulse Width ≤ 8ns) for I ≤ 20mA.
** VIH(Max) = VCC + 2.0V a.c (Pulse Width ≤ 8ns) for I ≤ 20mA.
DC AND OPERATING CHARACTERISTICS*(TA=0 to 70°C, Vcc=3.3±0.3V, unless otherwise specified)
Min
Max
Unit
Input Leakage Current
ILI
VIN=VSS to VCC
-2
2
µA
Output Leakage Current
ILO
CS=VIH or OE=VIH or WE=VIL
VOUT=VSS to VCC
-2
2
µA
Operating Current
ICC
Min. Cycle, 100% Duty
CS=VIL, VIN=VIH or VIL, IOUT=0mA
8ns
-
80
mA
10ns
-
65
Parameter
Symbol
Test Conditions
Com.
Ind.
Standby Current
8ns
-
90
10ns
-
75
ISB
Min. Cycle, CS=VIH
-
20
ISB1
f=0MHz, CS≥VCC-0.2V,
VIN≥VCC-0.2V or VIN≤0.2V
-
5
Output Low Voltage Level
VOL
IOL=8mA
-
0.4
V
Output High Voltage Level
VOH
IOH=-4mA
2.4
-
V
mA
* The above parameters are also guaranteed at industrial temperature range.
CAPACITANCE*(TA=25°C, f=1.0MHz)
Symbol
Test Conditions
TYP
Max
Unit
Input/Output Capacitance
Item
CI/O
VI/O=0V
-
8
pF
Input Capacitance
CIN
VIN=0V
-
6
pF
* Capacitance is sampled and not 100% tested.
-4-
Rev. 3.0
July 2004
PRELIMINARY
PRELIMINARY
for AT&T
K6R1004V1D
CMOS SRAM
AC CHARACTERISTICS(TA=0 to 70°C, VCC=3.3±0.3V, unless otherwise noted.)
TEST CONDITIONS
Parameter
Value
Input Pulse Levels
0V to 3V
Input Rise and Fall Times
3ns
Input and Output timing Reference Levels
1.5V
Output Loads
See below
Output Loads(B)
for tHZ, tLZ, tWHZ, tOW, tOLZ & tOHZ
Output Loads(A)
+3.3V
RL = 50Ω
DOUT
VL = 1.5V
319Ω
DOUT
30pF*
ZO = 50Ω
353Ω
5pF*
* Including Scope and Jig Capacitance
* Capacitive Load consists of all components of the
test environment.
READ CYCLE*
Parameter
Symbol
K6R1004V1D-08
Min
K6R1004V1D-10
Max
Min
Max
Unit
Read Cycle Time
tRC
8
-
10
-
ns
Address Access Time
tAA
-
8
-
10
ns
Chip Select to Output
tCO
-
8
-
10
ns
Output Enable to Valid Output
tOE
-
4
-
5
ns
Chip Enable to Low-Z Output
tLZ
3
-
3
-
ns
Output Enable to Low-Z Output
tOLZ
0
-
0
-
ns
tHZ
0
4
0
5
ns
Output Disable to High-Z Output
tOHZ
0
4
0
5
ns
Output Hold from Address Change
tOH
3
-
3
-
ns
Chip Selection to Power Up Time
tPU
0
-
0
-
ns
Chip Selection to Power DownTime
tPD
-
8
-
10
ns
Chip Disable to High-Z Output
* The above parameters are also guaranteed at industrial temperature range.
-5-
Rev. 3.0
July 2004
PRELIMINARY
PRELIMINARY
for AT&T
K6R1004V1D
CMOS SRAM
WRITE CYCLE*
Parameter
K6R1004V1D-08
Symbol
K6R1004V1D-10
Min
Max
Min
Max
Unit
Write Cycle Time
tWC
8
-
10
-
ns
Chip Select to End of Write
tCW
6
-
7
-
ns
Address Set-up Time
tAS
0
-
0
-
ns
Address Valid to End of Write
tAW
6
-
7
-
ns
Write Pulse Width(OE High)
tWP
6
-
7
-
ns
Write Pulse Width(OE Low)
tWP1
8
-
10
-
ns
Write Recovery Time
tWR
0
-
0
-
ns
Write to Output High-Z
tWHZ
0
4
0
5
ns
Data to Write Time Overlap
tDW
4
-
5
-
ns
Data Hold from Write Time
tDH
0
-
0
-
ns
End of Write to Output Low-Z
tOW
3
-
3
-
ns
* The above parameters are also guaranteed at industrial temperature range.
TIMING DIAGRAMS
TIMING WAVEFORM OF READ CYCLE(1) (Address Controlled, CS=OE=VIL, WE=VIH)
tRC
Address
tAA
tOH
Data Out
Valid Data
Previous Valid Data
TIMING WAVEFORM OF READ CYCLE(2) (WE=VIH)
tRC
Address
tAA
tCO
CS
tHZ(3,4,5)
tOHZ
tOE
OE
tOLZ
Data out
High-Z
VCC
ICC
Current
ISB
tDH
tLZ(4,5)
Valid Data
tPU
tPD
50%
50%
-6-
Rev. 3.0
July 2004
PRELIMINARY
PRELIMINARY
for AT&T
K6R1004V1D
CMOS SRAM
NOTES(READ CYCLE)
1. WE is high for read cycle.
2. All read cycle timing is referenced from the last valid address to the first transition address.
3. tHZ and tOHZ are defined as the time at which the outputs achieve the open circuit condition and are not referenced to VOH or
VOL levels.
4. At any given temperature and voltage condition, tHZ(Max.) is less than tLZ(Min.) both for a given device and from device to
device.
5. Transition is measured ±200mV from steady state voltage with Load(B). This parameter is sampled and not 100% tested.
6. Device is continuously selected with CS=VIL.
7. For common I/O applications, minimization or elimination of bus contention conditions is necessary during read and write cycle.
TIMING WAVEFORM OF WRITE CYCLE(1) (OE= Clock)
tWC
Address
tWR(5)
tAW
OE
tCW(3)
CS
tWP(2)
tAS(4)
WE
tDW
Data in
High-Z
tDH
Valid Data
tOHZ(6)
High-Z(8)
Data out
TIMING WAVEFORM OF WRITE CYCLE(2) (OE=Low Fixed)
tWC
Address
tAW
CS
tAS(4)
tWR(5)
tCW(3)
tWP1(2)
WE
tDW
Data in
High-Z
tDH
Valid Data
tWHZ(6)
tOW
High-Z(8)
Data out
-7-
(10)
(9)
Rev. 3.0
July 2004
PRELIMINARY
PRELIMINARY
for AT&T
K6R1004V1D
CMOS SRAM
TIMING WAVEFORM OF WRITE CYCLE(3) (CS=Controlled)
tWC
Address
tAW
tWR(5)
tCW(3)
CS
tWP(2)
tAS(4)
WE
tDW
High-Z
Data in
Valid Data
tLZ
High-Z
tWHZ(6)
High-Z(8)
High-Z
Data out
tDH
NOTES(WRITE CYCLE)
1. All write cycle timing is referenced from the last valid address to the first transition address.
2. A write occurs during the overlap of a low CS and WE. A write begins at the latest transition CS going low and WE going low ;
A write ends at the earliest transition CS going high or WE going high. tWP is measured from the beginning of write to the end of
write.
3. tCW is measured from the later of CS going low to end of write.
4. tAS is measured from the address valid to the beginning of write.
5. tWR is measured from the end of write to the address change. tWR applied in case a write ends as CS or WE going high.
6. If OE, CS and WE are in the Read Mode during this period, the I/O pins are in the output low-Z state. Inputs of opposite phase
of the output must not be applied because bus contention can occur.
7. For common I/O applications, minimization or elimination of bus contention conditions is necessary during read and write cycle.
8. If CS goes low simultaneously with WE going or after WE going low, the outputs remain high impedance state.
9. Dout is the read data of the new address.
10.When CS is low : I/O pins are in the output state. The input signals in the opposite phase leading to the output should not be
applied.
FUNCTIONAL DESCRIPTION
CS
WE
OE
Mode
I/O Pin
Supply Current
H
X
L
H
X*
Not Select
High-Z
ISB, ISB1
H
Output Disable
High-Z
ICC
L
L
H
L
Read
DOUT
ICC
L
X
Write
DIN
ICC
* X means Don′t Care.
-8-
Rev. 3.0
July 2004
PRELIMINARY
PRELIMINARY
for AT&T
K6R1004V1D
CMOS SRAM
Units:millimeters/Inches
PACKAGE DIMENSIONS
32-SOJ-400
#32
10.16
0.400
#17
11.18 ±0.12
0.440 ±0.005
9.40 ±0.25
0.370 ±0.010
0.20
#1
0.69 MIN
0.027
21.36 MAX
0.841
20.95 ±0.12
0.825 ±0.005
( 1.30 )
0.051
( 1.30 )
0.051
( 0.95 )
0.0375
+0.10
-0.05
+0.004
0.017 -0.002
0.43
1.27
0.050
+0.10
-0.05
0.008 +0.004
-0.002
#16
3.76 MAX
0.148
0.10
MAX
0.004
+0.10
-0.05
+0.004
0.028 -0.002
0.71
-9-
Rev. 3.0
July 2004
Similar pages