TECHNICAL DATA KK4013B Dual D Flip-Flop The KK4013B consists of two identical, independent data-type flipflops. Each flip-flop has independent data, set, reset, and clock inputs and Q and Q outputs. These devices can be used for shift register applications, and, by connecting Q output to the data input, for counter and toggle applications. The logic level present at the D input is transferred to the Q output during the positive-going transition of the clock pulse. Setting or resetting is independent of the clock and is accomplished by a high level on the set or reset line, respectively. • Operating Voltage Range: 3.0 to 18 V • Maximum input current of 1 µA at 18 V over full package-temperature range; 100 nA at 18 V and 25°C • Noise margin (over full package temperature range): 1.0 V min @ 5.0 V supply 2.0 V min @ 10.0 V supply 2.5 V min @ 15.0 V supply N SUFFIX PLASTIC 14 1 D SUFFIX SOIC 14 1 ORDERING INFORMATION KK4013BN Plastic KK4013BD SOIC TA = -55° to 125° C for all packages PIN ASSIGNMENT LOGIC DIAGRAM FUNCTION TABLE Inputs Outputs Clock Data Reset Set PIN 14 =VCC PIN 7 = GND Q Q L L L L H H L L H L X L L Q Q X X H L L H X X L H H L X X H H H H X = don’t care 1 KK4013B MAXIMUM RATINGS* Symbol Parameter VCC DC Supply Voltage (Referenced to GND) VIN DC Input Voltage (Referenced to GND) IIN DC Input Current, per Pin PD Power Dissipation in Still Air, Plastic DIP, SOIC Package Ptot Power Dissipation per Output Transistor Tstg Storage Temperature TL Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) Value Unit -0.5 to +20 V -0.5 to VCC +0.5 V ±10 mA 500** mW 100 mW -65 to +150 °C 260 °C * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. **Derating: - Plastic DIP from -55 to +100°C - SOIC Package from -55 to +65°C - Plastic DIP: - 12 mW/°C from +100 to +125°C - SOIC Package: : - 7 mW/°C from +65 to +125°C RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC DC Supply Voltage (Referenced to GND) VIN DC Input Voltage (Referenced to GND) TA Operating Temperature, All Package Types Min Max Unit 3.0 18 V 0 VCC V -55 +125 °C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation VIN should be constrained to the range GND≤VIN ≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. 2 KK4013B DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) VCC V ≥-55°C 25°C ≤125 °C Unit VOUT=0.5 V or VCC - 0.5 V VOUT=1.0 V or VCC - 1.0 V VOUT=1.5 V or VCC - 1.5 V 5.0 10 15 3.5 7 11 3.5 7 11 3.5 7 11 V Maximum Low Level Input Voltage VOUT=0.5 V or VCC - 0.5 V VOUT=1.0 V or VCC - 1.0 V VOUT=1.5 V or VCC - 1.5 V 5.0 10 15 1.5 3 4 1.5 3 4 1.5 3 4 V Minimum High-Level Output Voltage VIN=GND or VCC 5.0 10 15 5.0 10 15 4.95 9.95 14.95 4.5 9.0 13.5 4.95 9.95 14.95 4.5 9.0 13.5 4.95 9.95 14.95 4.5 9.0 13.5 V 0.05 0.05 0.05 0.5 1.0 1.5 0.05 0.05 0.05 0.5 1.0 1.5 0.05 0.05 0.05 0.5 1.0 1.5 V VIL=1.5V, VIH=3.5V, IO=1µA VIL=3.0V, VIH=7.0V, IO=1µA VIL=4.0V, VIH=11V, IO=1µA 5.0 10 15 5.0 10 15 Symbol Parameter VIH Minimum High-Level Input Voltage VIL VOH Test Conditions VIL=1.5V, VIH=3.5V, IO=-1µA VIL=3.0V, VIH=7.0V, IO=-1µA VIL=4.0V, VIH=11V, IO=-1µA VOL Guaranteed Limit Maximum Low-Level Output Voltage VIN=GND or VCC IIN Maximum Input Leakage Current VIN= GND or VCC 18 ±0.1 ±0.1 ±1.0 µA ICC Maximum Quiescent Supply Current (per Package) VIN= GND or VCC 5.0 10 15 20 1 2 4 20 1 2 4 20 30 60 120 600 µA IOL Minimum Output Low (Sink) Current VIN= GND or VCC UOL=0.4 V UOL=0.5 V UOL=1.5 V 5.0 10 15 0.64 1.6 4.2 0.51 1.3 3.4 0.36 0.9 2.4 Minimum Output VIN= GND or VCC High (Source) Current UOH=2.5 V UOH=4.6 V UOH=9.5 V UOH=13.5 V 5.0 5.0 10 15 -2.0 -0.64 -1.6 -4.2 -1.6 -0.51 -1.3 -3.4 -1.15 -0.36 -0.9 -2.4 IOH mA mA 3 KK4013B AC ELECTRICAL CHARACTERISTICS (CL=50pF, RL=200 kΩ, Input tr=tf=20 ns) VCC Guaranteed Limit V ≥-55°C 25°C ≤125°C Unit Maximum Clock Frequency (Figure 1) 5.0 10 15 3.5 8 12 3.5 8 12 3.0 6 10 MHz tPLH, tPHL Maximum Propagation Delay, Clock to Q or Q (Figure 1) 5.0 10 15 300 130 90 300 130 90 450 200 150 ns tPLH Maximum Propagation Delay, Set to Q or Reset to Q (Figure 2) 5.0 10 15 300 130 90 300 130 90 450 200 150 ns tPHL Maximum Propagation Delay, Set to Q or Reset to Q (Figure 2) 5.0 10 15 400 170 120 400 170 120 600 250 150 ns tTLH, tTHL Maximum Output Transition Time, Any Output (Figure 1) 5.0 10 15 200 100 80 200 100 80 250 150 100 ns Maximum Input Capacitance 5.0 Symbol fmax CIN Parameter 7.5 pF TIMING REQUIREMENTS(CL=50pF, RL=200 kΩ, Input tr=tf=20 ns) VCC Symbol Parameter Guaranteed Limit V ≥-55°C 25°C ≤125°C Unit tw Minimum Pulse Width, Clock (Figure 1) 5.0 10 15 140 60 40 140 60 40 200 80 50 ns tw Minimum Pulse Width, Set or Reset (Figure 2) 5.0 10 15 180 80 50 180 80 50 250 120 80 ns tsu Minimum Setup Time, Data to Clock (Figure 3) 5.0 10 15 40 20 15 40 20 15 40 20 15 ns th Minimum Hold Time, Clock to Data (Figure 3) 5.0 10 15 5 5 5 5 5 5 8 5 5 ns Maximum Input Rise or Fall Time, Clock (Figure 1) 5.0 10 15 500 30 6 500 30 6 500 30 6 µs tr, tf 4 KK4013B tr CLOCK tw tf VCC 90% 50% 10% SET OR RESET 0V 1/fmax tPLH 50% 10% 0V t PHL tw Q OR Q VCC 50% Q OR Q t PHL 0V 0V t THL t TLH VCC t PLH VCC 90% 50% VCC Q OR Q Figure 1. Switching Waveforms 50% 0V Figure 2. Switching Waveforms VCC DATA 50% 0V th t su CLOCK VCC 50% 0V Figure 3. Switching Waveforms EXPANDED LOGIC DIAGRAM (1/2 of the Device) 5 KK4013B N SUFFIX PLASTIC DIP (MS - 001AA) A 8 14 B Dimensions, mm 7 1 F L -T- SEATING PLANE M K G H D MIN MAX A 18.67 19.69 B 6.10 7.11 C C N Symbol J 5.33 D 0.36 0.56 F 1.14 1.78 G 2.54 H 7.62 J 0° 10° K 2.92 3.81 L 7.62 8.26 M 0.20 0.36 N 0.38 0.25 (0.010) M T NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. D SUFFIX SOIC (MS - 012AB) A 14 Dimensions, mm 8 H B 1 G P 7 R x 45 C -TK D SEATING PLANE J F 0.25 (0.010) M T C M NOTES: 1.Dimensions A and B do not include mold flash or protrusion. 2.Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B - 0.25 mm (0.010) per side. M Symbol. MIN MAX A 8.55 8.75 B 3.80 4.00 C 1.35 1.75 D 0.33 0.51 F 0.40 1.27 G 1.27 H 5.72 J 0° 8° K 0.10 0.25 M 0.19 0.25 P 5.80 6.20 R 0.25 0.50 6