L78L00 SERIES POSITIVE VOLTAGE REGULATORS ■ ■ ■ ■ ■ ■ OUTPUT CURRENT UP TO 100 mA OUTPUT VOLTAGES OF 3.3; 5; 6; 8; 9; 10; 12; 15; 18; 20; 24V THERMAL OVERLOAD PROTECTION SHORT CIRCUIT PROTECTION NO EXTERNAL COMPONENTS ARE REQUIRED AVAILABLE IN EITHER ±5% (AC) OR ±10% (C) SELECTION TO-92 DESCRIPTION The L78L00 series of three-terminal positive regulators employ internal current limiting and thermal shutdown, making them essentially indestructible. If adequate heat-sink is provided, they can deliver up to 100 mA output current. They are intended as fixed voltage regulators in a wide range of applications including local or on-card regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with power pass elements to make high-current voltage regulators. The L78L00 series used as Zener diode/resistor combination replacement, offers an effective output impedance improvement of typically two SO-8 SOT-89 orders of magnitude, along with lower quiescent current and lower noise. SCHEMATIC DIAGRAM July 2003 1/24 L78L00 SERIES ABSOLUTE MAXIMUM RATINGS Symbol Parameter² DC Input Voltage VI Value VO = 3.3 to 9 V 30 VO = 12 to 15 V 35 VO = 18 to 24 V IO Unit V 40 Output Current 100 mA Ptot Power Dissipation Tstg Storage Temperature Range -40 to 150 °C Top Operating Junction Temperature for L78L00C, L78L00AC Range for L78L00AB 0 to 125 -40 to 125 °C Internally Limited (*) (*) Our SO-8 package used for Voltage Regulators is modified internally to have pins 2, 3, 6 and 7 electrically communed to the die attach flag. This particular frame decreases the total thermal resistance of the package and increases its ability to dissipate power when an appropriate area of copper on the printed circuit board is available for heat-sinking. The external dimensions are the same as for the standard SO-8. THERMAL DATA Symbol Parameter SO-8 Rthj-case Thermal Resistance Junction-case Max 20 Rthj-amb Thermal Resistance Junction-ambient Max 55 (*) TO-92 SOT-89 Unit 15 °C/W 200 °C/W (*) Considering 6 cm2 of copper Board heat-sink TEST CIRCUITS CONNECTION DIAGRAM (top view) PIN 1 = VOUT PIN 2 = GND PIN 3 = VIN SO-8 SOT-89 TO-92 BOTTOM VIEW 2/24 L78L00 SERIES ORDERING CODES TYPE SO-8 (TUBE)* TO-92 (TUBE)** L78L33C L78L33AC L78L33AB L78L05C L78L05AC L78L05AB L78L06C L78L06AC L78L06AB L78L08C L78L08AC L78L08AB L78L09C L78L09AC L78L09AB L78L10C L78L10AC L78L10AB L78L12C L78L12AC L78L12AB L78L15C L78L15AC L78L15AB L78L18C L78L18AC L78L18AB L78L20C L78L20AC L78L20AB L78L24C L78L24AC L78L24AB L78L33CD L78L33ACD L78L33ABD L78L05CD L78L05ACD L78L05ABD L78L06CD L78L06ACD L78L06ABD L78L08CD L78L08ACD L78L08ABD L78L09CD L78L09ACD L78L09ABD L78L10CD L78L10ACD L78L10ABD L78L12CD L78L12ACD L78L12ABD L78L15CD L78L15ACD L78L15ABD L78L18CD L78L18ACD L78L18ABD L78L20CD L78L20ACD L78L20ABD L78L24CD L78L24ACD L78L24ABD L78L33CZ L78L33ACZ L78L33ABZ L78L05CZ L78L05ACZ L78L05ABZ L78L06CZ L78L06ACZ L78L06ABZ L78L08CZ L78L08ACZ L78L08ABZ L78L09CZ L78L09ACZ L78L09ABZ L78L10CZ L78L10ACZ L78L10ABZ L78L12CZ L78L12ACZ L78L12ABZ L78L15CZ L78L15ACZ L78L15ABZ L78L18CZ L78L18ACZ L78L18ABZ L78L20CZ L78L20ACZ L78L20ABZ L78L24CZ L78L24ACZ L78L24ABZ SOT-89 (T&R) L78L33ACUTR L78L33ABUTR L78L05ACUTR L78L05ABUTR L78L06ACUTR L78L06ABUTR L78L08ACUTR L78L08ABUTR L78L09ACUTR L78L09ABUTR L78L10ACUTR L78L10ABUTR L78L12ACUTR L78L12ABUTR L78L15ACUTR L78L15ABUTR L78L18ACUTR L78L18ABUTR L78L20ACUTR L78L20ABUTR L78L24ACUTR L78L24ABUTR OUTPUT VOLTAGE 3.3 V 3.3 V 3.3 V 5V 5V 5V 6V 6V 6V 8V 8V 8V 9V 9V 9V 10 V 10 V 10 V 12 V 12 V 12 V 15 V 15 V 15 V 18 V 18 V 18 V 20 V 20 V 20 V 24 V 24 V 24 V (*) Available in Tape & Reel with the suffix "13TR". (**) Available in Ammopak with the suffix "-AP" or in Tape & Reel with the suffix "TR". 3/24 L78L00 SERIES ELECTRICAL CHARACTERISTICS OF L78L33C (refer to the test circuits, TJ = 0 to 125°C, VI = 8.3V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. 3.036 3.3 Unit VO Output Voltage TJ = 25°C 3.564 V VO Output Voltage IO = 1 to 40 mA VI = 5.3 to 20 V 2.97 3.63 V IO = 1 to 70 mA VI = 8.3 V 2.97 3.63 ∆VO Line Regulation ∆VO Load Regulation Id ∆Id eN SVR Vd Quiescent Current Quiescent Current Change VI = 5.3 to 20 V TJ = 25°C 150 VI = 6.3 to 20 V TJ = 25°C 100 IO = 1 to 100 mA TJ = 25°C 60 IO = 1 to 40 mA TJ = 25°C 30 mV mV TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.2 mA VI = 6.3 to 20 V 1.5 Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 6.3 to 16.3 V IO = 40 mA TJ = 25°C f = 120Hz TJ = 25°C 41 Dropout Voltage 40 µV 49 dB 1.7 V ELECTRICAL CHARACTERISTICS OF L78L05C (refer to the test circuits, TJ = 0 to 125°C, VI = 10V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified). Symbol Parameter VO Output Voltage VO Output Voltage ∆VO ∆VO Id ∆Id eN SVR Vd 4/24 Line Regulation Load Regulation Quiescent Current Quiescent Current Change Test Conditions TJ = 25°C Typ. Max. Unit 4.6 5 5.4 V V IO = 1 to 40 mA VI =7 to 20 V 4.5 5.5 IO = 1 to 70 mA VI = 10 V 4.5 5.5 VI = 8.5 to 20 V TJ = 25°C 200 VI = 9 to 20 V TJ = 25°C 150 IO = 1 to 100 mA TJ = 25°C 60 IO = 1 to 40 mA TJ = 25°C 30 mV mV TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.2 mA VI = 8 to 20 V 1.5 Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 9 to 20 V IO = 40 mA Dropout Voltage Min. TJ = 25°C f = 120Hz TJ = 25°C 40 40 µV 49 dB 1.7 V L78L00 SERIES ELECTRICAL CHARACTERISTICS OF L78L06C (refer to the test circuits, TJ = 0 to 125°C, VI = 12V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified). Symbol Parameter Test Conditions Min. Typ. Max. 5.52 6 6.48 V 6.6 V VO Output Voltage TJ = 25°C VO Output Voltage IO = 1 to 40 mA VI =8.5 to 20 V 5.4 IO = 1 to 70 mA VI = 12 V 5.4 ∆VO Line Regulation ∆VO Load Regulation Id ∆Id eN SVR Vd Quiescent Current Quiescent Current Change Unit 6.6 VI = 8.5 to 20 V TJ = 25°C 200 VI = 9 to 20 V TJ = 25°C 150 IO = 1 to 100 mA TJ = 25°C 60 IO = 1 to 40 mA TJ = 25°C 30 mV mV TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.2 mA VI = 8 to 20 V 1.5 Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 9 to 20 V IO = 40 mA TJ = 25°C f = 120Hz TJ = 25°C 38 Dropout Voltage 50 µV 46 dB 1.7 V ELECTRICAL CHARACTERISTICS OF L78L08C (refer to the test circuits, TJ = 0 to 125°C, VI = 14V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified). Symbol Parameter VO Output Voltage VO Output Voltage ∆VO ∆VO Id ∆Id eN SVR Vd Line Regulation Load Regulation Quiescent Current Quiescent Current Change Test Conditions TJ = 25°C Typ. Max. Unit 7.36 8 8.64 V V IO = 1 to 40 mA VI =10.5 to 23 V 7.2 8.8 IO = 1 to 70 mA VI = 14 V 7.2 8.8 VI = 10.5 to 23 V TJ = 25°C 200 VI = 11 to 23 V TJ = 25°C 150 IO = 1 to 100 mA TJ = 25°C 80 IO = 1 to 40 mA TJ = 25°C 40 mV mV TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.2 mA VI = 11 to 23 V 1.5 Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 12 to 23 V IO = 40 mA Dropout Voltage Min. TJ = 25°C f = 120Hz TJ = 25°C 36 60 µV 45 dB 1.7 V 5/24 L78L00 SERIES ELECTRICAL CHARACTERISTICS OF L78L09C (refer to the test circuits, TJ = 0 to 125°C, VI = 15V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified). Symbol Parameter Test Conditions Min. Typ. Max. Unit 8.28 9 9.72 V 9.9 V VO Output Voltage TJ = 25°C VO Output Voltage IO = 1 to 40 mA VI =11.5 to 23 V 8.1 IO = 1 to 70 mA VI = 15 V 8.1 ∆VO Line Regulation ∆VO Load Regulation Id ∆Id eN SVR Vd Quiescent Current Quiescent Current Change VI = 11.5 to 23 V 9.9 TJ = 25°C 250 VI = 12 to 23 V TJ = 25°C 200 IO = 1 to 100 mA TJ = 25°C 80 IO = 1 to 40 mA TJ = 25°C 40 mV mV TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.2 mA VI = 12 to 23 V 1.5 Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 12 to 23 V IO = 40 mA TJ = 25°C f = 120Hz TJ = 25°C 36 Dropout Voltage 70 µV 44 dB 1.7 V ELECTRICAL CHARACTERISTICS OF L78L10C (refer to the test circuits, TJ = 0 to 125°C, VI = 16V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified). Symbol Parameter VO Output Voltage VO Output Voltage ∆VO ∆VO Id ∆Id eN SVR Vd 6/24 Line Regulation Load Regulation Quiescent Current Quiescent Current Change Test Conditions TJ = 25°C Typ. Max. Unit 9.2 10 10.8 V V IO = 1 to 40 mA VI =12.5 to 23 V 9 11 IO = 1 to 70 mA VI = 16 V 9 11 VI = 12.5 to 23 V TJ = 25°C 230 VI = 13 to 23 V TJ = 25°C 170 IO = 1 to 100 mA TJ = 25°C 80 IO = 1 to 40 mA TJ = 25°C 40 mV mV TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.1 mA VI = 13 to 23 V 1.5 Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 14 to 23 V IO = 40 mA Dropout Voltage Min. TJ = 25°C f = 120Hz TJ = 25°C 37 60 µV 45 dB 1.7 V L78L00 SERIES ELECTRICAL CHARACTERISTICS OF L78L12C (refer to the test circuits, TJ = 0 to 125°C, VI = 19V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified). Symbol Parameter Test Conditions Min. Typ. 11.1 12 Max. Unit VO Output Voltage TJ = 25°C 12.9 V VO Output Voltage IO = 1 to 40 mA VI =14.5 to 27 V 10.8 13.2 V IO = 1 to 70 mA VI = 19 V 10.8 13.2 ∆VO Line Regulation ∆VO Load Regulation Id ∆Id eN SVR Vd Quiescent Current Quiescent Current Change VI = 14.5 to 27 V TJ = 25°C 250 VI = 16 to 27 V TJ = 25°C 200 IO = 1 to 100 mA TJ = 25°C 100 IO = 1 to 40 mA TJ = 25°C 50 mV mV TJ = 25°C 6.5 mA TJ = 125°C 6 mA IO = 1 to 40 mA 0.2 mA VI = 16 to 27 V 1.5 Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 15 to 25 V IO = 40 mA TJ = 25°C f = 120Hz TJ = 25°C 36 Dropout Voltage 80 µV 42 dB 1.7 V ELECTRICAL CHARACTERISTICS OF L78L15C (refer to the test circuits, TJ = 0 to 125°C, VI = 23V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified). Symbol Parameter VO Output Voltage VO Output Voltage ∆VO ∆VO Id ∆Id eN SVR Vd Line Regulation Load Regulation Quiescent Current Quiescent Current Change Test Conditions TJ = 25°C Typ. Max. Unit 13.8 15 16.2 V V IO = 1 to 40 mA VI =17.5 to 30 V 13.5 16.5 IO = 1 to 70 mA VI = 23 V 13.5 16.5 VI = 17.5 to 30 V TJ = 25°C 300 VI = 20 to 30 V TJ = 25°C 250 IO = 1 to 100 mA TJ = 25°C 150 IO = 1 to 40 mA TJ = 25°C 75 mV mV TJ = 25°C 6.5 mA TJ = 125°C 6 mA IO = 1 to 40 mA 0.2 mA VI = 20 to 30 V 1.5 TJ = 25°C Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 18.5 to 28.5 V f = 120Hz IO = 40 mA TJ = 25°C Dropout Voltage Min. 33 90 µV 39 dB 1.7 V 7/24 L78L00 SERIES ELECTRICAL CHARACTERISTICS OF L78L18C (refer to the test circuits, TJ = 0 to 125°C, VI = 27V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified). Symbol Parameter Test Conditions Min. Typ. 16.6 18 Max. Unit VO Output Voltage TJ = 25°C 19.4 V VO Output Voltage IO = 1 to 40 mA VI = 22 to 33 V 16.2 19.8 V IO = 1 to 70 mA VI = 27 V 16.2 19.8 ∆VO Line Regulation ∆VO Load Regulation Id ∆Id eN SVR Vd Quiescent Current Quiescent Current Change VI = 22 to 33 V TJ = 25°C 320 VI = 22 to 33 V TJ = 25°C 270 IO = 1 to 100 mA TJ = 25°C 170 IO = 1 to 40 mA TJ = 25°C 85 mV mV TJ = 25°C 6.5 mA TJ = 125°C 6 mA IO = 1 to 40 mA 0.2 mA VI = 23 to 33 V 1.5 Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 23 to 33 V IO = 40 mA TJ = 25°C f = 120Hz TJ = 25°C 32 Dropout Voltage 120 µV 38 dB 1.7 V ELECTRICAL CHARACTERISTICS OF L78L20C (refer to the test circuits, TJ = 0 to 125°C, VI = 29V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified) Symbol Parameter VO Output Voltage VO Output Voltage ∆VO ∆VO Id ∆Id eN SVR Vd 8/24 Line Regulation Load Regulation Quiescent Current Quiescent Current Change Test Conditions TJ = 25°C Typ. Max. Unit 18.4 20 21.6 V V IO = 1 to 40 mA VI = 24 to 33 V 18 22 IO = 1 to 70 mA VI = 29 V 18 22 VI = 22.5 to 34 V TJ = 25°C 330 VI = 24 to 34 V TJ = 25°C 280 IO = 1 to 100 mA TJ = 25°C 180 IO = 1 to 40 mA TJ = 25°C 90 mV mV TJ = 25°C 6.5 mA TJ = 125°C 6 mA IO = 1 to 40 mA 0.2 mA VI = 25 to 33 V 1.5 Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 25 to 35 V IO = 40 mA Dropout Voltage Min. TJ = 25°C f = 120Hz TJ = 25°C 31 120 µV 38 dB 1.7 V L78L00 SERIES ELECTRICAL CHARACTERISTICS OF L78L24C (refer to the test circuits, TJ = 0 to 125°C, VI = 33V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified). Symbol Parameter Test Conditions Min. Typ. 22.1 24 Max. Unit VO Output Voltage TJ = 25°C 25.9 V VO Output Voltage IO = 1 to 40 mA VI = 27 to 38 V 21.6 26.4 V IO = 1 to 70 mA VI = 33 V 21.6 26.4 ∆VO Line Regulation ∆VO Load Regulation Id ∆Id eN SVR Vd Quiescent Current Quiescent Current Change VI = 27 to 38 V TJ = 25°C 350 VI = 28 to 38 V TJ = 25°C 300 IO = 1 to 100 mA TJ = 25°C 200 IO = 1 to 40 mA TJ = 25°C 100 mV mV TJ = 25°C 6.5 mA TJ = 125°C 6 mA IO = 1 to 40 mA 0.2 mA VI = 28 to 38 V 1.5 Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 29 to 35 V IO = 40 mA TJ = 25°C f = 120Hz TJ = 25°C 30 Dropout Voltage 200 µV 37 dB 1.7 V ELECTRICAL CHARACTERISTICS OF L78L33AB AND L78L33AC (refer to the test circuits, VI = 8.3V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125°C for L78L33AC, TJ = -40 to 125°C for L78L33AB, unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. 3.168 3.3 Max. Unit VO Output Voltage TJ = 25°C 3.432 V VO Output Voltage IO = 1 to 40 mA VI = 5.3 to 20 V 3.135 3.465 V IO = 1 to 70 mA VI = 8.3 V 3.135 3.465 ∆VO Line Regulation ∆VO Load Regulation Id ∆Id eN SVR Vd Quiescent Current Quiescent Current Change VI = 5.3 to 20 V TJ = 25°C 150 VI = 6.3 to 20 V TJ = 25°C 100 IO = 1 to 100 mA TJ = 25°C 60 IO = 1 to 40 mA TJ = 25°C 30 mV TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.1 mA VI = 6.3 to 20 V 1.5 Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 6.3 to 16.3 V IO = 40 mA Dropout Voltage mV TJ = 25°C f = 120Hz TJ = 25°C 41 40 µV 49 dB 1.7 V 9/24 L78L00 SERIES ELECTRICAL CHARACTERISTICS OF L78L05AB AND L78L05AC (refer to the test circuits, VI = 10V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125°C for L78L05AC, TJ = -40 to 125°C for L78L05AB, unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. 4.8 5 Max. Unit VO Output Voltage TJ = 25°C 5.2 V VO Output Voltage IO = 1 to 40 mA VI = 7 to 20 V 4.75 5.25 V IO = 1 to 70 mA VI = 10 V 4.75 5.25 ∆VO ∆VO Id ∆Id eN SVR Vd Line Regulation Load Regulation Quiescent Current Quiescent Current Change VI = 7 to 20 V TJ = 25°C 150 VI = 8 to 20 V TJ = 25°C 100 IO = 1 to 100 mA TJ = 25°C 60 IO = 1 to 40 mA TJ = 25°C 30 mV mV TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.1 mA VI = 8 to 20 V 1.5 Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 8 to 18 V IO = 40 mA TJ = 25°C f = 120Hz TJ = 25°C 41 Dropout Voltage 40 µV 49 dB 1.7 V ELECTRICAL CHARACTERISTICS OF L78L06AB AND L78L06AC (refer to the test circuits, VI = 12V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125°C for L78L06AC, TJ = -40 to 125°C for L78L06AB, unless otherwise specified) Symbol Parameter VO Output Voltage VO Output Voltage ∆VO ∆VO Id Line Regulation Load Regulation Quiescent Current Test Conditions TJ = 25°C Min. Typ. Max. Unit 5.76 6 6.24 V V IO = 1 to 40 mA VI = 8.5 to 20 V 5.7 6.3 IO = 1 to 70 mA VI = 12 V 5.7 6.3 VI = 8.5 to 20 V TJ = 25°C 150 VI = 9 to 20 V TJ = 25°C 100 IO = 1 to 100 mA TJ = 25°C 60 IO = 1 to 40 mA TJ = 25°C 30 TJ = 25°C 6 mA 5.5 mA IO = 1 to 40 mA 0.1 mA Quiescent Current Change eN Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 9 to 20 V IO = 40 mA VI = 9 to 20 V Vd 10/24 Dropout Voltage mV TJ = 125°C ∆Id SVR mV 1.5 TJ = 25°C f = 120Hz TJ = 25°C 39 50 µV 46 dB 1.7 V L78L00 SERIES ELECTRICAL CHARACTERISTICS OF L78L08AB AND L78L08AC (refer to the test circuits, VI = 14V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125°C for L78L08AC, TJ = -40 to 125°C for L78L08AB, unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. 7.68 8 8.32 V 8.4 V VO Output Voltage TJ = 25°C VO Output Voltage IO = 1 to 40 mA VI = 10.5 to 23 V 7.6 IO = 1 to 70 mA VI = 14 V 7.6 ∆VO Line Regulation ∆VO Load Regulation Id ∆Id eN SVR Vd Quiescent Current Quiescent Current Change VI = 10.5 to 23 V Unit 8.4 TJ = 25°C 175 VI = 11 to 23 V TJ = 25°C 125 IO = 1 to 100 mA TJ = 25°C 80 IO = 1 to 40 mA TJ = 25°C 40 mV mV TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.1 mA VI = 11 to 23 V 1.5 Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 12 to 23 V IO = 40 mA TJ = 25°C f = 120Hz TJ = 25°C 37 Dropout Voltage 60 µV 45 dB 1.7 V ELECTRICAL CHARACTERISTICS OF L78L09AB AND L78L09AC (refer to the test circuits, VI = 15V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125°C for L78L09AC, TJ = -40 to 125°C for L78L09AB, unless otherwise specified) Symbol Parameter Test Conditions VO Output Voltage TJ = 25°C VO Output Voltage IO = 1 to 40 mA VI = 11.5 to 23 V IO = 1 to 70 mA VI = 15 V ∆VO Line Regulation ∆VO Load Regulation Id Quiescent Current VI = 11.5 to 23 V Min. Typ. Max. Unit 8.64 9 9.36 V 8.55 9.45 V 8.55 9.45 TJ = 25°C 225 VI = 12 to 23 V TJ = 25°C 150 IO = 1 to 100 mA TJ = 25°C 80 IO = 1 to 40 mA TJ = 25°C 40 TJ = 25°C 6 5.5 mA 0.1 mA eN Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 12 to 23 V IO = 40 mA VI = 12 to 23 V Dropout Voltage mA IO = 1 to 40 mA Quiescent Current Change Vd mV TJ = 125°C ∆Id SVR mV 1.5 TJ = 25°C f = 120Hz TJ = 25°C 37 70 µV 44 dB 1.7 V 11/24 L78L00 SERIES ELECTRICAL CHARACTERISTICS OF L78L10AB AND L78L10AC (refer to the test circuits, VI = 16V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125°C for L78L10AC, TJ = -40 to 125°C for L78L10AB, unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. 9.6 10 Max. Unit VO Output Voltage TJ = 25°C 10.4 V VO Output Voltage IO = 1 to 40 mA VI =12.5 to 23 V 9.5 10.5 V IO = 1 to 70 mA VI = 16 V 9.5 10.5 ∆VO ∆VO Id ∆Id eN SVR Vd Line Regulation Load Regulation Quiescent Current Quiescent Current Change VI = 12.5 to 23 V TJ = 25°C 230 VI = 13 to 23 V TJ = 25°C 170 IO = 1 to 100 mA TJ = 25°C 80 IO = 1 to 40 mA TJ = 25°C 40 mV mV TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.1 mA VI = 13 to 23 V 1.5 Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 14 to 23 V IO = 40 mA TJ = 25°C f = 120Hz TJ = 25°C 37 Dropout Voltage 60 µV 45 dB 1.7 V ELECTRICAL CHARACTERISTICS OF L78L12AB AND L78L12AC (refer to the test circuits, VI = 19V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125°C for L78L12AC, TJ = -40 to 125°C for L78L12AB, unless otherwise specified) Symbol Parameter VO Output Voltage VO Output Voltage ∆VO ∆VO Id Line Regulation Load Regulation Quiescent Current Test Conditions TJ = 25°C Min. Typ. Max. Unit 11.5 12 12.5 V V IO = 1 to 40 mA VI = 14.5 to 27 V 11.4 12.6 IO = 1 to 70 mA VI = 19 V 11.4 12.6 VI = 14.5 to 27 V TJ = 25°C 250 VI = 16 to 27 V TJ = 25°C 200 IO = 1 to 100 mA TJ = 25°C 100 IO = 1 to 40 mA TJ = 25°C 6.5 TJ = 125°C Quiescent Current Change eN Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 15 to 25 V IO = 40 mA IO = 1 to 40 mA VI = 16 to 27 V SVR Vd 12/24 Dropout Voltage mV 50 TJ = 25°C ∆Id mV mA 6 mA 0.1 mA 1.5 TJ = 25°C f = 120Hz TJ = 25°C 37 80 µV 42 dB 1.7 V L78L00 SERIES ELECTRICAL CHARACTERISTICS OF L78L15AB AND L78L15AC (refer to the test circuits, VI = 19V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125°C for L78L15AC, TJ = -40 to 125°C for L78L15AB, unless otherwise specified) Symbol Parameter VO Output Voltage VO Output Voltage ∆VO ∆VO Id ∆Id eN SVR Vd Line Regulation Load Regulation Quiescent Current Quiescent Current Change Test Conditions TJ = 25°C Min. Typ. Max. Unit 14.4 15 15.6 V V IO = 1 to 40 mA VI = 17.5 to 30 V 14.25 15.75 IO = 1 to 70 mA VI = 23 V 14.25 15.75 VI = 17.5 to 30 V TJ = 25°C 300 VI = 20 to 30 V TJ = 25°C 250 IO = 1 to 100 mA TJ = 25°C 150 IO = 1 to 40 mA TJ = 25°C 75 mV mV TJ = 25°C 6.5 mA TJ = 125°C 6 mA IO = 1 to 40 mA 0.1 mA VI = 20 to 30 V 1.5 TJ = 25°C Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 18.5 to 28.5 V f = 120Hz IO = 40 mA TJ = 25°C 34 Dropout Voltage 90 µV 39 dB 1.7 V ELECTRICAL CHARACTERISTICS OF L78L18AB AND L78L18AC (refer to the test circuits, VI = 27V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125°C for L78L18AC, TJ = -40 to 125°C for L78L18AB, unless otherwise specified) Symbol Parameter VO Output Voltage VO Output Voltage ∆VO ∆VO Id Line Regulation Load Regulation Quiescent Current Test Conditions TJ = 25°C Min. Typ. Max. Unit 17.3 18 18.7 V V IO = 1 to 40 mA VI = 22 to 33 V 17.1 18.9 IO = 1 to 70 mA VI = 27 V 17.1 18.9 VI = 22 to 33 V TJ = 25°C 320 VI = 22 to 33 V TJ = 25°C 270 IO = 1 to 100 mA TJ = 25°C 170 IO = 1 to 40 mA TJ = 25°C 6.5 TJ = 125°C Quiescent Current Change eN Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 23 to 33 V IO = 40 mA IO = 1 to 40 mA VI = 23 to 33 V SVR Vd Dropout Voltage mV 85 TJ = 25°C ∆Id mV mA 6 mA 0.1 mA 1.5 TJ = 25°C f = 120Hz TJ = 25°C 33 120 µV 38 dB 1.7 V 13/24 L78L00 SERIES ELECTRICAL CHARACTERISTICS OF L78L20AB AND L78L20AC (refer to the test circuits, VI = 29V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125°C for L78L20AC, TJ = -40 to 125°C for L78L20AB, unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. 19.2 20 Unit VO Output Voltage TJ = 25°C 20.8 V VO Output Voltage IO = 1 to 40 mA VI = 24 to 33 V 19 21 V IO = 1 to 70 mA VI = 29 V 19 21 ∆VO ∆VO Id ∆Id eN SVR Vd Line Regulation Load Regulation Quiescent Current Quiescent Current Change VI = 22.5 to 34 V TJ = 25°C 330 VI = 24 to 34 V TJ = 25°C 280 IO = 1 to 100 mA TJ = 25°C 180 IO = 1 to 40 mA TJ = 25°C 90 mV mV TJ = 25°C 6.5 mA TJ = 125°C 6 mA IO = 1 to 40 mA 0.1 mA VI = 25 to 33 V 1.5 Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 25 to 35 V IO = 40 mA TJ = 25°C f = 120Hz TJ = 25°C 32 Dropout Voltage 120 µV 38 dB 1.7 V ELECTRICAL CHARACTERISTICS OF L78L24AB AND L78L24AC (refer to the test circuits, VI = 27V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125°C for L78L24AC, TJ = -40 to 125°C for L78L24AB, unless otherwise specified) Symbol Parameter VO Output Voltage VO Output Voltage ∆VO ∆VO Id Line Regulation Load Regulation Quiescent Current Test Conditions TJ = 25°C Min. Typ. Max. Unit 23 24 25 V V IO = 1 to 40 mA VI = 27 to 38 V 22.8 25.2 IO = 1 to 70 mA VI = 33 V 22.8 25.2 VI = 27 to 38 V TJ = 25°C 350 VI = 28 to 38 V TJ = 25°C 300 IO = 1 to 100 mA TJ = 25°C 200 IO = 1 to 40 mA TJ = 25°C 100 TJ = 25°C 6.5 TJ = 125°C ∆Id Quiescent Current Change eN Output Noise Voltage B =10Hz to 100KHz Supply Voltage Rejection VI = 23 to 33 V IO = 40 mA IO = 1 to 40 mA VI = 28 to 38 V SVR Vd 14/24 Dropout Voltage mV mV mA 6 mA 0.1 mA 1.5 TJ = 25°C f = 120Hz TJ = 25°C 31 200 µV 37 dB 1.7 V L78L00 SERIES Figure 1 : L78L05/12 Output Voltage vs Ambient Temperature Figure 4 : L78L05/12 Quiescent Current vs Output Current Figure 2 : L78L05/12/24 Load Characteristics Figure 5 : L78L05 Quiescent Current vs Input Voltage Figure 3 : L78L05/12/24 Thermal Shutdown Figure 6 : L78L05/12/24 Output Characteristics 15/24 L78L00 SERIES Figure 7 : L78L05/12/24 Ripple Rejection Figure 8 : L78L05 Dropout Characteristics 16/24 Figure 9 : L78L00 Series Short Circuit Output Current L78L00 SERIES TYPICAL APPLICATIONS Table 10 : High Output Current Short Circuit Protected Figure 11 : Edit Boost Circuit Figure 12 : Current Regulator 17/24 L78L00 SERIES Figure 13 : Adjustable Output Regulator 18/24 L78L00 SERIES SO-8 MECHANICAL DATA DIM. mm. MIN. TYP inch MAX. MIN. TYP. MAX. A 1.35 1.75 0.053 0.069 A1 0.10 0.25 0.04 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 E 3.80 4.00 0.150 0.157 e 1.27 0.050 H 5.80 6.20 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 k ddd 8˚ (max.) 0.1 0.04 0016023/C 19/24 L78L00 SERIES SOT-89 MECHANICAL DATA mm. mils DIM. MIN. TYP MAX. MIN. TYP. MAX. A 1.4 1.6 55.1 63.0 B 0.44 0.56 17.3 22.0 B1 0.36 0.48 14.2 18.9 C 0.35 0.44 13.8 17.3 C1 0.35 0.44 13.8 17.3 D 4.4 4.6 173.2 181.1 D1 1.62 1.83 63.8 72.0 E 2.29 2.6 90.2 102.4 e 1.42 1.57 55.9 61.8 e1 2.92 3.07 115.0 120.9 H 3.94 4.25 155.1 167.3 L 0.89 1.2 35.0 47.2 P025H 20/24 L78L00 SERIES TO-92 MECHANICA DATA mm. mils DIM. MIN. TYP MAX. MIN. TYP. MAX. A 4.32 4.95 170.1 194.9 b 0.36 0.51 14.2 20.1 D 4.45 4.95 175.2 194.9 E 3.30 3.94 129.9 155.1 e 2.41 2.67 94.9 105.1 e1 1.14 1.40 44.9 55.1 L 12.7 15.49 500.0 609.8 R 2.16 2.41 85.0 94.9 S1 0.92 1.52 36.2 59.8 W 0.41 0.56 16.1 22.0 0102782/C 21/24 L78L00 SERIES Tape & Reel SO-8 MECHANICAL DATA mm. inch DIM. MIN. A MAX. MIN. 330 13.2 TYP. MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 22/24 TYP 0.504 22.4 0.519 0.882 Ao 8.1 8.5 0.319 0.335 Bo 5.5 5.9 0.216 0.232 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 L78L00 SERIES Tape & Reel SOT89 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. 180 13.0 7.086 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 MAX. 0.504 0.512 14.4 0.519 0.567 Ao 4.70 4.80 4.90 0.185 0.189 0.193 Bo 4.30 4.40 4.50 0.169 0.173 0.177 Ko 1.70 1.80 1.90 0.067 0.071 0.075 Po 3.9 4.0 4.1 0.153 0.157 0.161 P 7.9 8.0 8.1 0.311 0.315 0.319 23/24 L78L00 SERIES Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2003 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. © http://www.st.com 24/24