L79L00 SERIES NEGATIVE VOLTAGE REGULATORS ■ ■ ■ ■ ■ ■ OUTPUT CURRENT UP TO 100 mA OUTPUT VOLTAGES OF-5; -6; -8; -9; -12; -15V THERMAL OVERLOAD PROTECTION SHORT CIRCUIT PROTECTION NO EXTERNAL COMPONENTS ARE REQUIRED AVAILABLEIN EITHER ± 5% (AC) OR ± 10% (C) SELECTION DESCRIPTION The L79L00 series of three-terminal positive regulators employ internal current limiting and thermal shutdown, making them essentially indestructible. If adequate heatsink is provided, they can deliver up to 100 mA output current. They are intended as fixed voltage regulators in a wide range of applications including local or on-card regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with power pass elements to make high-current voltage regulators. The L79L00 series used as Zener diode/resistor combination replacement, offers an effective SO-8 SOT-89 TO-92 output impedance improvement of typically two orders of magnetude, along with lower quiescent current and lower noise. BLOCK DIAGRAM December 1999 1/13 L79L00 ABSOLUTE MAXIMUM RATING Symbol Parameter Vi DC Input Voltage Io Output Current Vo = -5 V to -9 V Vo = -12 V to -15 V P tot Power Dissipation T st g Storage Temperature Range T op Value Unit -30 V -35 V 100 mA Internally limited (*) Operating Junction Temperature Range For L79L00C, L79L00AC For L79L00AB - 40 to 150 o C 0 to 125 - 40 to 125 o C C o (*) Our SO-8 package used for Voltage Regulators is modified internally to have pins 2, 3, 6 and 7 electrically commoned to the die attach flag. This particular frame decreases the total thermal resistance of the package and increases its ability to dissipate power when an appropriate area of copper on the printed circuit board is available for heatsinking. The external dimensions are the same as for the standard SO-8 THERMAL DATA Symbol Parameter R thj- ca se Thermal Resistance Junction-case R thj- amb Thermal Resistance Junction-ambient (*) Considering 6cm2 of copper Board heat-sink TEST CIRCUITS 2/13 SO-8 Max Max 20 55 (*) TO-92 SOT-89 15 200 Unit o o C/W C/W L79L00 CONNECTION DIAGRAM AND ORDERING NUMBERS (top view) pin 1 = GND pin 2 = VIN pin 3 = VOUT SO-8 SOT-89 TO-92 BOTTOM VIEW ORDERING NUMBERS Type L79L05C L79L05AC L79L05AB L79L06C L79L06AC L79L06AB L79L08C L79L08AC L79L08AB L79L09C L79L09AC L79L09AB L79L12C L79L12AC L79L12AB L79L15C L79L15AC L79L15AB SO-8 L79L05CD L79L05ACD L79L05ABD L79L06CD L79L06ACD L79L06ABD L79L08CD L79L08ACD L79L08ABD L79L09CD L79L09ACD L79L09ABD L79L12CD L79L12ACD L79L12ABD L79L15CD L79L15ACD L79L15ABD TO-92 L79L05CZ L79L05ACZ L79L05ABZ L79L06CZ L79L06ACZ L79L06ABZ L79L08CZ L79L08ACZ L79L08ABZ L79L09CZ L79L09ACZ L79L09ABZ L79L12CZ L79L12ACZ L79L12ABZ L79L15CZ L79L15ACZ L79L15ABZ SOT-89 L79L05ACU L79L05ABU L79L06ACU L79L06ABU L79L08ACU L79L08ABU L79L09ACU L79L09ABU L79L12ACU L79L12ABU Output Voltage -5 V -5 V -5 V -6 V -6 V -6 V -8 V -8 V -8 V -9 V -9 V -9 V -12 V -12 V -12 V -15 V -15 V -15 V 3/13 L79L00 ELECTRICAL CHARACTERISTICS FOR L79L05 (refer to the test circuits, T j = 0 to 125 oC, Vi = -10V, Io = 40 mA, Ci = 0.33 µF, Co = 0.1 µF unless otherwise specified) Symbol Parameter Test Conditions o Min. Typ. Max. Unit -4.6 -5 -5.4 V -5.5 -5.5 V V 200 150 mV mV 60 30 mV mV 6 5.5 mA mA Vo Output Voltage Tj = 25 C Vo Output Voltage Io = 1 to 40 mA Io = 1 to 70 mA ∆V o Line Regulation Vi = -7 to -20 V Vi = -8 to -20 V ∆V o Load Regulation Io = 1 to 100 mA Io = 1 to 40 mA Quiescent Current Tj = 25 oC Tj = 125 oC ∆I d Quiescent Current Change Io = 1 to 40 mA 0.2 mA ∆I d Quiescent Current Change Vi = -8 to -20 V 1.5 mA eN Output Noise Voltage B = 10Hz to 100KHz Tj = 25 oC Id SVR Vd Supply Voltage Rejection Vi = -7 to -20 V Vi = -10 V -4.5 -4.5 Tj = 25 oC o Tj = 25 C o Tj = 25 C Tj = 25 oC o Io = 40 mA f = 120 Hz Tj = 25 C Vi = -8 to -18 V 40 Dropout Voltage 40 µV 49 dB 1.7 V ELECTRICAL CHARACTERISTICS FOR L79L06 (refer to the test circuits, T j = 0 to 125 oC, Vi = -12V, Io = 40 mA, Ci = 0.33 µF, Co = 0.1 µF unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit -5.52 -6 -6.48 V -6.6 -6.6 V V Vi = -8.5 to -20 V Tj = 25 oC Vi = -9 to -20 V Tj = 25 oC 200 150 mV mV Tj = 25 oC Tj = 25 oC 60 30 mV mV Tj = 25 oC Tj = 125 oC 6 5.5 mA mA Io = 1 to 40 mA 0.2 mA 1.5 mA Vo Output Voltage Tj = 25 oC Vo Output Voltage Io = 1 to 40 mA Io = 1 to 70 mA ∆V o Line Regulation ∆V o Load Regulation Io = 1 to 100 mA Io = 1 to 40 mA Quiescent Current ∆I d Quiescent Current Change ∆I d Quiescent Current Change Vi = -8 to -20 V eN Output Noise Voltage B = 10Hz to 100KHz Tj = 25 oC Supply Voltage Rejection Io = 40 mA f = 120 Hz Tj = 25 oC Vi = -9 to -20 V Id SVR Vd 4/13 Dropout Voltage Vi = -8.5 to -20 V Vi = -12 V -5.4 -5.4 38 50 µV 46 dB 1.7 V L79L00 ELECTRICAL CHARACTERISTICS FOR L79L08 (refer to the test circuits, T j = 0 to 125 oC, Vi = -14V, Io = 40 mA, Ci = 0.33 µF, Co = 0.1 µF unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit -7.36 -8 -8.64 V -8.8 -8.8 V V 200 150 mV mV 80 40 mV mV Tj = 25 oC Tj = 125 oC 6 5.5 mA mA Quiescent Current Change Io = 1 to 40 mA 0.2 mA Quiescent Current Change Vi = -11 to -23 V 1.5 mA o Vo Output Voltage Tj = 25 C Vo Output Voltage Io = 1 to 40 mA Io = 1 to 70 mA ∆V o Line Regulation Vi = -10.5 to -23 V Tj = 25 oC o Tj = 25 C Vi = -11 to -23 V ∆V o Load Regulation Io = 1 to 100 mA Io = 1 to 40 mA Quiescent Current ∆I d ∆I d Id eN SVR Vd Output Noise Voltage Supply Voltage Rejection Vi = -10.5 to -23 V Vi = -14 V -7.2 -7.2 o Tj = 25 C Tj = 25 oC o B = 10Hz to 100KHz Tj = 25 C o Io = 40 mA f = 120 Hz Tj = 25 C Vi = -12 to -23 V 36 Dropout Voltage 60 µV 45 dB 1.7 V ELECTRICAL CHARACTERISTICS FOR L79L09 (refer to the test circuits, T j = 0 to 125 oC, Vi = -15V, Io = 40 mA, Ci = 0.33 µF, Co = 0.1 µF unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit -8.28 -9 -9.72 V -9.9 -9.9 V V Vi = -11.5 to -23 V Tj = 25 oC Vi = -12 to -23 V Tj = 25 oC 250 200 mV mV Tj = 25 oC Tj = 25 oC 80 40 mV mV Tj = 25 oC Tj = 125 oC 6 5.5 mA mA Io = 1 to 40 mA 0.2 mA 1.5 mA Vo Output Voltage Tj = 25 oC Vo Output Voltage Io = 1 to 40 mA Io = 1 to 70 mA ∆V o Line Regulation ∆V o Load Regulation Io = 1 to 100 mA Io = 1 to 40 mA Quiescent Current ∆I d Quiescent Current Change ∆I d Quiescent Current Change Vi = -12 to -23 V eN Output Noise Voltage B = 10Hz to 100KHz Tj = 25 oC Supply Voltage Rejection Io = 40 mA f = 120 Hz Tj = 25 oC Vi = -12 to -23 V Id SVR Vd Dropout Voltage Vi = -11.5 to -23 V Vi = -15 V -8.1 -8.1 36 70 µV 44 dB 1.7 V 5/13 L79L00 ELECTRICAL CHARACTERISTICS FOR L79L12 (refer to the test circuits, T j = 0 to 125 oC, Vi = -19V, Io = 40 mA, Ci = 0.33 µF, Co = 0.1 µF unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit -11.1 -12 -12.9 V -13.2 -13.2 V V 250 200 mV mV 100 50 mV mV Tj = 25 oC Tj = 125 oC 6.5 6 mA mA Quiescent Current Change Io = 1 to 40 mA 0.2 mA Quiescent Current Change Vi = -16 to -27 V 1.5 mA o Vo Output Voltage Tj = 25 C Vo Output Voltage Io = 1 to 40 mA Io = 1 to 70 mA ∆V o Line Regulation Vi = -14.5 to -27 V Tj = 25 oC o Vi = -16 to -27 V Tj = 25 C ∆V o Load Regulation Io = 1 to 100 mA Io = 1 to 40 mA Quiescent Current ∆I d ∆I d Id eN SVR Vd Output Noise Voltage Supply Voltage Rejection Vi = -14.5 to -27 V Vi = -19 V -10.8 -10.8 o Tj = 25 C Tj = 25 oC o B = 10Hz to 100KHz Tj = 25 C o Io = 40 mA f = 120 Hz Tj = 25 C Vi = -15 to -25 V 36 Dropout Voltage 80 µV 42 dB 1.7 V ELECTRICAL CHARACTERISTICS FOR L79L15 (refer to the test circuits, T j = 0 to 125 oC, Vi = -23V, Io = 40 mA, Ci = 0.33 µF, Co = 0.1 µF unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit -13.8 -15 -16.2 V -16.5 -16.5 V V Vi = -17.5 to -30 V Tj = 25 oC Vi = -20 to -30 V Tj = 25 oC 300 250 mV mV Tj = 25 oC Tj = 25 oC 150 75 mV mV Tj = 25 oC Tj = 125 oC 6.5 6 mA mA Io = 1 to 40 mA 0.2 mA 1.5 mA Vo Output Voltage Tj = 25 oC Vo Output Voltage Io = 1 to 40 mA Io = 1 to 70 mA ∆V o Line Regulation ∆V o Load Regulation Io = 1 to 100 mA Io = 1 to 40 mA Quiescent Current ∆I d Quiescent Current Change ∆I d Quiescent Current Change Vi = -20 to -30 V eN Output Noise Voltage B = 10Hz to 100KHz Tj = 25 oC Supply Voltage Rejection Io = 40 mA f = 120 Hz Tj = 25 oC Vi = -18.5 to -28.5 V Id SVR Vd 6/13 Dropout Voltage Vi = -17.5 to -30 V Vi = -23 V -13.5 -13.5 33 90 µV 39 dB 1.7 V L79L00 ELECTRICAL CHARACTERISTICS FOR L79L05AB AND L79L05AC (refer to the test circuits, Vi = -10V, Io = 40 mA, Ci = 0.33 µF, Co = 0.1 µF, Tj = 0 to 125 oC for L79L05AC, Tj = -40 to 125 oC for L79L05AB, unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit -4.8 -5 -5.2 V -5.25 -5.25 V V 150 100 mV mV 60 30 mV mV 6 5.5 mA mA Vo Output Voltage Tj = 25 oC Vo Output Voltage Io = 1 to 40 mA Io = 1 to 70 mA ∆V o Line Regulation Vi = -7 to -20 V Vi = -8 to -20 V ∆V o Load Regulation Io = 1 to 100 mA Io = 1 to 40 mA Quiescent Current Tj = 25 oC Tj = 125 oC ∆I d Quiescent Current Change Io = 1 to 40 mA 0.1 mA ∆I d Quiescent Current Change Vi = -8 to -20 V 1.5 mA eN Output Noise Voltage B = 10Hz to 100KHz Tj = 25 oC Id SVR Vd Supply Voltage Rejection Vi = -7 to -20 V Vi = -10 V -4.75 -4.75 Tj = 25 oC Tj = 25 oC Tj = 25 oC Tj = 25 oC o Io = 40 mA f = 120 Hz Tj = 25 C Vi = -8 to -18 V 41 Dropout Voltage 40 µV 49 dB 1.7 V ELECTRICAL CHARACTERISTICS FOR L79L06AB AND L79L06AC (refer to the test circuits, Vi = -12V, Io = 40 mA, Ci = 0.33 µF, Co = 0.1 µF, Tj = 0 to 125 oC for L79L06AC, Tj = -40 to 125 oC for L79L06AB, unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit -5.76 -6 -6.24 V -6.3 -6.3 V V Vi = -8.5 to -20 V Tj = 25 oC Vi = -9 to -20 V Tj = 25 oC 150 100 mV mV Tj = 25 oC Tj = 25 oC 60 30 mV mV 6 5.5 mA mA Vo Output Voltage Tj = 25 oC Vo Output Voltage Io = 1 to 40 mA Io = 1 to 70 mA ∆V o Line Regulation ∆V o Load Regulation Io = 1 to 100 mA Io = 1 to 40 mA Quiescent Current Tj = 25 oC Tj = 125 oC ∆I d Quiescent Current Change Io = 1 to 40 mA 0.1 mA ∆I d Quiescent Current Change Vi = -9 to -20 V 1.5 mA eN Output Noise Voltage B = 10Hz to 100KHz Tj = 25 oC Id SVR Vd Supply Voltage Rejection Dropout Voltage Vi = -8.5 to -20 V Vi = -12 V o Io = 40 mA f = 120 Hz Tj = 25 C Vi = -9 to -20 V -5.7 -5.7 39 50 µV 46 dB 1.7 V 7/13 L79L00 ELECTRICAL CHARACTERISTICS FOR L79L08AB AND L79L08AC (refer to the test circuits, Vi = -14V, Io = 40 mA, Ci = 0.33 µF, Co = 0.1 µF, Tj = 0 to 125 oC for L79L08AC, Tj = -40 to 125 oC for L79L08AB, unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit -7.68 -8 -8.32 V -8.4 -8.4 V V Vi = -10.5 to -23 V Tj = 25 oC Vi = -11 to -23 V Tj = 25 oC 175 125 mV mV Tj = 25 oC Tj = 25 oC 80 40 mV mV Tj = 25 oC Tj = 125 oC 6 5.5 mA mA Quiescent Current Change Io = 1 to 40 mA 0.1 mA Quiescent Current Change Vi = -11 to -23 V 1.5 mA Vo Output Voltage Tj = 25 oC Vo Output Voltage Io = 1 to 40 mA Io = 1 to 70 mA ∆V o Line Regulation ∆V o Load Regulation Io = 1 to 100 mA Io = 1 to 40 mA Quiescent Current ∆I d ∆I d Id eN SVR Vd Output Noise Voltage Supply Voltage Rejection Vi = -10.5 to -23 V Vi = -14 V -7.6 -7.6 o B = 10Hz to 100KHz Tj = 25 C o Io = 40 mA f = 120 Hz Tj = 25 C Vi = -12 to -23 V 37 Dropout Voltage 60 µV 45 dB 1.7 V ELECTRICAL CHARACTERISTICS FOR L79L09AB AND L79L09AC (refer to the test circuits, Vi = -15V, Io = 40 mA, Ci = 0.33 µF, Co = 0.1 µF, Tj = 0 to 125 oC for L79L09AC, Tj = -40 to 125 oC for L79L09AB, unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit -8.64 -9 -9.36 V -9.45 -9.45 V V Vi = -11.5 to -23 V Tj = 25 oC Vi = -12 to -23 V Tj = 25 oC 225 150 mV mV Tj = 25 oC Tj = 25 oC 80 40 mV mV Tj = 25 oC Tj = 125 oC 6 5.5 mA mA Quiescent Current Change Io = 1 to 40 mA 0.1 mA Quiescent Current Change Vi = -12 to -23 V 1.5 mA Vo Output Voltage Tj = 25 oC Vo Output Voltage Io = 1 to 40 mA Io = 1 to 70 mA ∆V o Line Regulation ∆V o Load Regulation Io = 1 to 100 mA Io = 1 to 40 mA Quiescent Current ∆I d ∆I d Id eN SVR Vd 8/13 Output Noise Voltage Supply Voltage Rejection Dropout Voltage Vi = -11.5 to -23 V Vi = -15 V -8.55 -8.55 o B = 10Hz to 100KHz Tj = 25 C o Io = 40 mA f = 120 Hz Tj = 25 C Vi = -12 to -23 V 37 70 µV 44 dB 1.7 V L79L00 ELECTRICAL CHARACTERISTICS FOR L79L12AB AND L79L12AC (refer to the test circuits, Vi = -19V, Io = 40 mA, Ci = 0.33 µF, Co = 0.1 µF, Tj = 0 to 125 oC for L79L12AC, Tj = -40 to 125 oC for L79L12AB, unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit -11.5 -12 -12.5 V -12.6 -12.6 V V Vi = -14.5 to -27 V Tj = 25 oC Vi = -16 to -27 V Tj = 25 oC 250 200 mV mV Tj = 25 oC Tj = 25 oC 100 50 mV mV Tj = 25 oC Tj = 125 oC 6.5 6 mA mA Quiescent Current Change Io = 1 to 40 mA 0.1 mA Quiescent Current Change Vi = -16 to -27 V 1.5 mA Vo Output Voltage Tj = 25 oC Vo Output Voltage Io = 1 to 40 mA Io = 1 to 70 mA ∆V o Line Regulation ∆V o Load Regulation Io = 1 to 100 mA Io = 1 to 40 mA Quiescent Current ∆I d ∆I d Id eN SVR Vd Output Noise Voltage Supply Voltage Rejection Vi = -14.5 to -27 V Vi = -19 V -11.4 -11.4 o B = 10Hz to 100KHz Tj = 25 C o Io = 40 mA f = 120 Hz Tj = 25 C Vi = -15 to -25 V 37 Dropout Voltage 80 µV 42 dB 1.7 V ELECTRICAL CHARACTERISTICS FOR L79L15AB AND L79L15AC (refer to the test circuits, Vi = -23V, Io = 40 mA, Ci = 0.33 µF, Co = 0.1 µF, Tj = 0 to 125 oC for L79L15AC, Tj = -40 to 125 oC for L79L15AB, unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit -14.4 -15 -15.6 V -15.75 -15.75 V V Vi = -17.5 to -30 V Tj = 25 oC Vi = -20 to -30 V Tj = 25 oC 300 250 mV mV Tj = 25 oC Tj = 25 oC 150 75 mV mV Tj = 25 oC Tj = 125 oC 6.5 6 mA mA Quiescent Current Change Io = 1 to 40 mA 0.1 mA Quiescent Current Change Vi = -20 to -30 V 1.5 mA Vo Output Voltage Tj = 25 oC Vo Output Voltage Io = 1 to 40 mA Io = 1 to 70 mA ∆V o Line Regulation ∆V o Load Regulation Io = 1 to 100 mA Io = 1 to 40 mA Quiescent Current ∆I d ∆I d Id eN SVR Vd Output Noise Voltage Supply Voltage Rejection Dropout Voltage Vi = -17.5 to -30 V Vi = -23 V -14.25 -14.25 o B = 10Hz to 100KHz Tj = 25 C o Io = 40 mA f = 120 Hz Tj = 25 C Vi = -18.5 to -28.5 V 34 90 µV 39 dB 1.7 V 9/13 L79L00 SO-8 MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.25 a2 MAX. 0.003 0.009 1.65 0.064 a3 0.65 0.85 0.025 0.033 b 0.35 0.48 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.25 0.5 0.010 0.019 c1 45 (typ.) D 4.8 5.0 0.188 0.196 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 3.81 0.150 F 3.8 4.0 0.14 0.157 L 0.4 1.27 0.015 0.050 M S 0.6 0.023 8 (max.) 0016023 10/13 L79L00 SOT-89 MECHANICAL DATA mm DIM. MIN. TYP. mils MAX. MIN. TYP. MAX. A 1.4 1.6 55.1 63.0 B 0.44 0.56 17.3 22.0 B1 0.36 0.48 14.2 18.9 C 0.35 0.44 13.8 17.3 C1 0.35 0.44 13.8 17.3 D 4.4 4.6 173.2 181.1 D1 1.62 1.83 63.8 72.0 E 2.29 2.6 90.2 102.4 e 1.42 1.57 55.9 61.8 e1 2.92 3.07 115.0 120.9 H 3.94 4.25 155.1 167.3 L 0.89 1.2 35.0 47.2 P025H 11/13 L79L00 TO-92 MECHANICAL DATA mm inch DIM. MIN. MAX. MIN. TYP. MAX. A 4.58 5.33 0.180 0.210 B 4.45 5.2 0.175 0.204 C 3.2 4.2 0.126 0.165 D 12.7 E 12/13 TYP. 0.500 1.27 F 0.4 G 0.35 0.050 0.51 0.016 0.14 0.020 L79L00 Information furnished is believed to be accurate and reliable. However, STMicroelectronic s assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems withoutexpress written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 1999 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. http://www.st.com . 13/13