Ordering number : ENA0647A Monolithic Linear IC Separately-Excited Step-Down LA5744TP Switching Regulator (Variable Type) Overview The LA5744TP is a separately-excited step-down switching regulator (variable type). Functions • High efficiency. • Time-base generator (300kHz) incorporated. • Current limiter incorporated. • Thermal shutdown circuit incorporated. • Soft start circuit incorporated. Specifications Maximum Ratings at Ta = 25°C Parameter Input voltage Symbol Conditions Ratings VIN Maximum output current SW pin application reverse voltage Allowable power dissipation Unit 30 V IO max 2 A VSW -1 V 1.1 W Operating temperature Topr -30 to +125 °C Storage temperature Tstg -40 to +150 °C * Specified circuit board : 76.1×114.3×1.6mm3, Pd max Mounted on a circuit board.* glass epoxy. Recommended Operating Conditions at Ta = 25°C Parameter Input voltage range Symbol VIN Conditions Ratings Unit 4.5 to 28 V Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. 42007 MS PC 20070420-S00001 / 11707 MS PC 20061204-S00012 No.A0647-1/5 LA5744TP Electrical Characteristics at Ta = 25°C, VO = 5V Parameter Symbol Ratings Conditions min Reference voltage Efficiency Switching frequency VOS VIN = 15V, IO = 1.0A η VIN = 15V, IO = 1.0A f Unit typ 1.20 max 1.23 1.26 V 83 300 360 kHz Line regulation ∆VOLINE VIN = 8 to 20V, IO = 1.0A 40 100 mV Load regulation ∆VOLOAD VIN = 20V, IO = 0.5 to 1.5A 10 30 ∆VO/∆Ta Output voltage temperature VIN = 15V, IO = 1.0A 240 % ±0.5 Designed target value. * mV mV/°C coefficient Ripple attenuation factor RREJ Current limiter operating voltage IS Thermal shutdown operating f = 100 to 120Hz 45 VIN = 15V dB 3.1 A TSD Designed target value. * 165 °C ∆TSD Designed target value. * 15 °C temperature Thermal shutdown Hysteresis width * Design target value : No measurement made. Package Dimensions unit : mm (typ) 3332 Pd max -- Ta 6.5 2.3 1.5 5.0 2.5 1.2 0.8 (5.5) 7.0 0.5 0.2 0.6 (0.65) 1.3 1 2 0.5 0.5 1.2 5 Allowable power dissipation, Pd max – W 1.4 Specified board : 114.3×76.1×1.6mm3 glass epoxy 1.2 1.1 1 0.8 0.6 0.4 0.22 0.2 0 --30--20 0 20 40 60 80 100 120 140 Ambient temperature, Ta – °C SANYO : TP5HFA Pin Assignment (1) VIN (2) SWOUT (3) GND (4) VOS (5) SS No.A0647-2/5 LA5744TP Block Diagram VIN 1 2 SWOUT Constant current circuit Reg. OCP Reset OSC Drive Comp. TSD 4 VOS Amp. ON/OFF Comp. 0.4V VREF 5 3 SS GND Application Circuit Example L1 22µH VIN SWOUT LA5744TP C2 390µF D1 SBD C1 470µF /50V VOS SS GND R2 R1 C3 1µF Notes : 1. C3 is for the soft start function. Delete C3 and keep the SS pin open when the soft start function is not necessary. 2. In some cases, the output may not turn on if power is applied when a load is connected. If this is a problem, increase the value of the inductor. No.A0647-3/5 LA5744TP Protection Circuit Functional Descriptions 1. Overcurrent protection function The overcurrent protection function detects, on a cycle-by-cycle basis, the output transistor current and turns off that output transistor current if it exceeds 3.1A. Limit current Inductor current SWOUT voltage 2. Short circuit protection function This IC prevents the current from increasing when the outputs are shorted by setting the switching frequency to 30kHz if the VOS pin voltage falls below 0.8V. Note 3 : If the soft start function is not used, the IC will start up with the overcurrent protection function operating. At this time, the switching frequency will be cut in half. This means that the switching frequency will be 15kHz at startup. Note 4 : Since the switching frequency becomes 30kHz when the VOS pin voltage falls under 0.8V, the current capacity is reduced. If a load is applied with the VOS pin voltage over 0.8V, the inductance value operates at 22µH. If a load is to be applied when this voltage is under 0.8V, the inductance value must be increased. Description of Functional Settings 1. Calculation equation to set the output voltage This IC controls the switching output so that the VOS pin voltage becomes 1.23V (typ). The equation to set the output voltage is as follows : R2 VO = 1+ × 1.23V(typ) R1 The VOS pin has the inrush current of 1µA (typ). Therefore, the error becomes larger when R1 and R2 resistance values are large. 2. Startup Delay Function The output voltage rises when the internal voltage reaches 0.4V (typical). Until that point, a capacitor is charged from an internal 10µA (typical) constant-current supply. The startup delay time can be calculated as shown below Example : Assume a 1µF capacitor is used. Td = C × V 1µF × 0.4 = = 40 ms i 10µA No.A0647-4/5 LA5744TP Timing Chart VIN voltage 30kHz 300kHz SWOUT voltage 1.23V 0.8V VOS voltage 0V Td SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of April, 2007. Specifications and information herein are subject to change without notice. PS No.A0647-5/5