LD1086 SERIES 1.5A LOW DROP POSITIVE VOLTAGE REGULATOR ADJUSTABLE AND FIXED ■ ■ ■ ■ ■ ■ ■ ■ TYPICAL DROPOUT 1.3V AT 1.5A THREE TERMINAL ADJUSTABLE OR FIXED OUTPUT VOLTAGE 1.2V, 1.5V, 1.8V, 2.5V, 2.85V, 3.3V, 3.6V, 5V, 8V, 9V, 12V. GUARANTEED OUTPUT CURRENT UP TO 1.5A OUPUT TOLERANCE ±1% AT 25°C AND ±2% IN FULL TEMPERATURE RANGE INTERNAL POWER AND THERMAL LIMIT WIDE OPERATING TEMPERATURE RANGE -40°C TO 125°C PACKAGE AVAILABLE : TO-220, D2PAK, D2PAK/A, DPAK PINOUT COMPATIBILITY WITH STANDARD ADJUSTABLE VREG DESCRIPTION The LD1086 is a LOW DROP Voltage Regulator able to provide up to 1.5A of Output Current. Dropout is guaranteed at a maximum of 1.2V at the maximum output current, decreasing at lower loads. The LD1086 is pin to pin compatible with the older 3-terminal adjustable regulators, but has better performances in term of drop and output tolerance . TO-220 D2PAK DPAK D2PAK/A A 2.85V output version is suitable for SCSI-2 active termination. Unlike PNP regulators, where a part of the output current is wasted as quiescent current, the LD1086 quiescent current flows into the load, so increase efficiency. Only a 10µF minimum capacitor is need for stability. The device is supplied in TO-220, D2PAK, D2PAK/A and DPAK. On chip trimming allows the regulator to reach a very tight output voltage tolerance, within ±1% at 25°C. SCHEMATIC DIAGRAM October 2003 1/20 LD1086 SERIES ABSOLUTE MAXIMUM RATINGS Symbol Parameter² Value Unit VI DC Input Voltage 30 V IO Output Current Internally Limited mA PD Power Dissipation Internally Limited mW Tstg Storage Temperature Range -55 to +150 °C Top Operating Junction Temperature Range -40 to +125 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. THERMAL DATA Symbol Parameter TO-220 D2PAK DPAK Unit 8 °C/W Rthj-case Thermal Resistance Junction-case 3 3 Rthj-amb Thermal Resistance Junction-ambient 50 62.5 APPLICATION CIRCUITS R2 VO = VREF (1 + ) R1 2/20 °C/W LD1086 SERIES CONNECTION DIAGRAM (top view) TO-220 D2PAK DPAK D2PAK/A ORDERING CODES TO-220 D2PAK (*) D2PAK/A (*) DPAK (*) OUTPUT VOLTAGE LD1086V12 LD1086V15 LD1086V18 LD1086V25 LD1086V28 LD1086V33 LD1086V36 LD1086V50 LD1086V80 LD1086V90 LD1086V12 LD1086V LD1086D2T12 LD1086D2T15 LD1086D2T18 LD1086D2T25 LD1086D2T28 LD1086D2T33 LD1086D2T36 LD1086D2T50 LD1086D2T80 LD1086D2T90 LD1086D2T12 LD1086D2T LD1086D2M12 LD1086D2M15 LD1086D2M18 LD1086D2M25 LD1086D2M28 LD1086D2M33 LD1086D2M36 LD1086D2M50 LD1086D2M80 LD1086D2M90 LD1086D2M12 LD1086D2M LD1086DT12 LD1086DT15 LD1086DT18 LD1086DT25 LD1086DT28 LD1086DT33 LD1086DT36 LD1086DT50 LD1086DT80 LD1086DT90 LD1086DT12 LD1086DT 1.2 V 1.5 V 1.8 V 2.5 V 2.85 V 3.3 V 3.6 V 5.0 V 8.0 V 9.0 V 12.0 V ADJ (*) Available in Tape & Reel with the suffix "TR". 3/20 LD1086 SERIES ELECTRICAL CHARACTERISTICS OF LD1086#12 (VI=4.5V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO Parameter Output Voltage (note 1) Test Conditions IO = 0 mA TJ = 25°C IO = 0 to 1.5A ∆VO ∆VO Line Regulation Load Regulation Min. VI = 3.4 to 30V IO = 0 mA VI = 3.1 to 18V IO = 0 mA VI = 3.1 to 15V IO = 0 to 1.5A Typ. Max. 1.485 1.5 1.515 V 1.47 1.5 1.53 V TJ = 25°C TJ = 25°C IO = 0 to 1.5A 0.2 4 mV 0.4 4 mV 0.5 8 mV 1 16 V 1.3 1.5 V 5 10 mA Vd Dropout Voltage Iq Quiescent Current VI ≤ 30V Isc Short Circuit Current VI - VO = 5V 1.5 2 VI - VO = 25V 0.05 0.02 SVR eN S S IO = 1.5A Termal Regulation TA = 25°C, 30ms pulse Supply Voltage Rejection f = 120 Hz, CO = 25 µF, IO = 1.5A VI = 6.5 ± 3V RMS Output Noise Voltage (% of VO) TA = 25°C f =10Hz to 10KHz TA = 125°C 1000Hrs Temperature Stability Long Term Stability 0.01 60 Unit A A 0.04 %/W 82 dB 0.003 % 0.5 0.5 % % NOTE 1: See short-circuit current curve for available output current at fixed dropout. ELECTRICAL CHARACTERISTICS OF LD1086#15 (VI=4.5V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO Parameter Output Voltage (note 1) Test Conditions IO = 0 mA IO = 0 to 1.5A TJ = 25°C VI = 3.4 to 30V Min. Typ. Max. Unit 1.485 1.5 1.515 V 1.47 1.5 1.53 V 0.2 4 mV 0.4 4 mV 0.5 8 mV ∆VO Line Regulation ∆VO Load Regulation Vd Dropout Voltage Iq Quiescent Current VI ≤ 30V Isc Short Circuit Current VI - VO = 5V 1.5 2 VI - VO = 25V 0.05 0.02 IO = 0 mA VI = 3.1 to 18V IO = 0 mA VI = 3.1 to 15V IO = 0 to 1.5A TJ = 25°C TJ = 25°C IO = 0 to 1.5A SVR eN S S IO = 1.5A Termal Regulation TA = 25°C, 30ms pulse Supply Voltage Rejection f = 120 Hz, CO = 25 µF, IO = 1.5A VI = 6.5 ± 3V RMS Output Noise Voltage (% of VO) TA = 25°C f =10Hz to 10KHz TA = 125°C 1000Hrs Temperature Stability Long Term Stability NOTE 1: See short-circuit current curve for available output current at fixed dropout. 4/20 1 16 V 1.3 1.5 V 5 10 mA 0.01 60 A A 0.04 %/W 82 dB 0.003 % 0.5 0.5 % % LD1086 SERIES ELECTRICAL CHARACTERISTICS OF LD1086#18 (VI=4.8V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO Parameter Output Voltage (note 1) Test Conditions IO = 0 mA TJ = 25°C IO = 0 to 1.5A ∆VO ∆VO Line Regulation Load Regulation Min. VI = 3.4 to 30V IO = 0 mA VI = 3.4 to 18V IO = 0 mA VI = 3.4 to 15V IO = 0 to 1.5A Typ. 1.782 1.8 1.818 V 1.8 1.836 V TJ = 25°C IO = 0 to 1.5A 4 mV 4 mV 0.5 8 mV 1 16 V 1.3 1.5 V 5 10 mA Dropout Voltage Iq Quiescent Current VI ≤ 30V Isc Short Circuit Current VI - VO = 5V 1.5 2 VI - VO = 25V 0.05 0.02 SVR eN S S IO = 1.5A 0.2 0.4 Vd TA = 25°C, 30ms pulse Supply Voltage Rejection f = 120 Hz, CO = 25 µF, IO = 1.5A VI = 6.8 ± 3V RMS Output Noise Voltage (% of VO) TA = 25°C f =10Hz to 10KHz TA = 125°C 1000Hrs Temperature Stability Long Term Stability Unit 1.764 TJ = 25°C Termal Regulation Max. 0.01 60 A A 0.04 %/W 82 dB 0.003 % 0.5 0.5 % % NOTE 1: See short-circuit current curve for available output current at fixed dropout. ELECTRICAL CHARACTERISTICS OF LD1086#25 (VI=5.5V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO Parameter Output Voltage (note 1) Test Conditions IO = 0 mA IO = 0 to 1.5A TJ = 25°C VI = 4.1 to 30V Min. Typ. Max. Unit 2.475 2.5 2.525 V 2.45 2.5 2.55 V 0.2 4 mV 0.4 4 mV 0.5 8 mV ∆VO Line Regulation ∆VO Load Regulation Vd Dropout Voltage Iq Quiescent Current VI ≤ 30V Isc Short Circuit Current VI - VO = 5V 1.5 VI - VO = 25V 0.05 IO = 0 mA VI = 4.1 to 18V IO = 0 mA VI = 4.1 to 18V IO = 0 to 1.5A TJ = 25°C TJ = 25°C IO = 0 to 1.5A SVR eN S S IO = 1.5A Termal Regulation TA = 25°C, 30ms pulse Supply Voltage Rejection f = 120 Hz, CO = 25 µF, IO = 1.5A VI = 7.5 ± 3V RMS Output Noise Voltage (% of VO) TA = 25°C f =10Hz to 10KHz TA = 125°C 1000Hrs Temperature Stability Long Term Stability 1 16 V 1.3 1.5 V 5 10 mA 2 0.2 0.008 60 A A 0.04 %/W 81 dB 0.003 % 0.5 0.5 % % NOTE 1: See short-circuit current curve for available output current at fixed dropout. 5/20 LD1086 SERIES ELECTRICAL CHARACTERISTICS OF LD1086#285 (VI=5.85V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO Parameter Output Voltage (note 1) Test Conditions IO = 0 mA TJ = 25°C IO = 0 to 1.5A ∆VO ∆VO Line Regulation Load Regulation Min. VI = 4.5 to 30V IO = 0 mA VI = 4.5 to 18V IO = 0 mA VI = 4.5 to 18V IO = 0 to 1.5A 2.85 2.879 V 2.85 2.907 V TJ = 25°C Vd Dropout Voltage Iq Quiescent Current VI ≤ 30V Isc Short Circuit Current VI - VO = 5V 1.5 VI - VO = 25V 0.05 SVR eN S S IO = 1.5A Supply Voltage Rejection f = 120 Hz, CO = 25 µF, IO = 1.5A VI = 7.85 ± 3V RMS Output Noise Voltage (% of VO) TA = 25°C f =10Hz to 10KHz TA = 125°C 1000Hrs Temperature Stability Long Term Stability Unit 2.821 IO = 0 to 1.5A TA = 25°C, 30ms pulse Max. 2.793 TJ = 25°C Termal Regulation Typ. 0.2 6 mV 0.5 6 mV 1 12 mV 2 20 V 1.3 1.5 V 5 10 mA 2 0.2 0.01 60 A A 0.04 %/W 80 dB 0.003 % 0.5 0.5 % % NOTE 1: See short-circuit current curve for available output current at fixed dropout. ELECTRICAL CHARACTERISTICS OF LD1086#33 (VI=6.3V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO Parameter Output Voltage (note 1) Test Conditions IO = 0 mA TJ = 25°C IO = 0 to 1.5A‘ VI = 4.9 to 30V Min. Typ. Max. Unit 3.267 3.3 3.333 V 3.234 3.35 3.366 V 0.5 6 mV 1 6 mV 1 10 mV ∆VO Line Regulation ∆VO Load Regulation Vd Dropout Voltage Iq Quiescent Current VI ≤ 30V Isc Short Circuit Current VI - VO = 5V 1.5 VI - VO = 25V 0.05 IO = 0 mA VI = 4.9 to 18V IO = 0 mA VI = 4.9 to 18V IO = 0 to 1.5A TJ = 25°C TJ = 25°C IO = 0 to 1.5A SVR eN S S IO = 1.5A Termal Regulation TA = 25°C, 30ms pulse Supply Voltage Rejection f = 120 Hz, CO = 25 µF, IO = 1.5A VI = 8.3 ± 3V RMS Output Noise Voltage (% of VO) TA = 25°C f =10Hz to 10KHz TA = 125°C 1000Hrs Temperature Stability Long Term Stability NOTE 1: See short-circuit current curve for available output current at fixed dropout. 6/20 7 25 V 1.3 1.5 V 5 10 mA 2 0.2 0.008 60 A A 0.04 %/W 79 dB 0.003 % 0.5 0.5 % % LD1086 SERIES ELECTRICAL CHARACTERISTICS OF LD1086#36 (VI=6.6V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO Parameter Output Voltage (note 1) Test Conditions IO = 0 mA TJ = 25°C IO = 0 to 1.5A ∆VO ∆VO Line Regulation Load Regulation Min. VI = 5.2 to 30V IO = 0 mA VI = 5.2 to 18V IO = 0 mA VI = 5.2 to 18V IO = 0 to 1.5A 3.6 3.636 V 3.6 3.672 V TJ = 25°C Vd Dropout Voltage Iq Quiescent Current VI ≤ 30V Isc Short Circuit Current VI - VO = 5V 1.5 VI - VO = 25V 0.05 SVR eN S S IO = 1.5A Supply Voltage Rejection f = 120 Hz, CO = 25 µF, IO = 1.5A VI = 8.6 ± 3V RMS Output Noise Voltage (% of VO) TA = 25°C f =10Hz to 10KHz TA = 125°C 1000Hrs Temperature Stability Long Term Stability Unit 3.564 IO = 0 to 1.5A TA = 25°C, 30ms pulse Max. 3.528 TJ = 25°C Termal Regulation Typ. 0.5 10 mV 1 10 mV 3 15 mV 7 25 V 1.3 1.5 V 5 10 mA 2 0.2 0.01 60 A A 0.04 %/W 78 dB 0.003 % 0.5 0.5 % % NOTE 1: See short-circuit current curve for available output current at fixed dropout. ELECTRICAL CHARACTERISTICS OF LD1086#50 (VI=8V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO Parameter Output Voltage (note 1) Test Conditions IO = 0 mA IO = 0 to 1.5A ∆VO ∆VO Line Regulation Load Regulation TJ = 25°C VI = 6.6 to 30V IO = 0 mA VI = 6.6 to 20V IO = 0 mA VI = 6.6 to 20V IO = 0 to 1.5A Min. Typ. Max. Unit 4.95 5 5.05 V 4.9 5 5.1 V TJ = 25°C TJ = 25°C 0.5 10 mV 1 10 mV 5 20 mV IO = 0 to 1.5A 10 35 V Vd Dropout Voltage IO = 1.5A 1.3 1.5 V Iq Quiescent Current VI ≤ 30V 5 10 mA Isc Short Circuit Current VI - VO = 5V 1.5 2 A VI - VO = 25V 0.05 0.2 A SVR eN S S Termal Regulation TA = 25°C, 30ms pulse Supply Voltage Rejection f = 120 Hz, CO = 25 µF, IO = 1.5A VI = 10 ± 3V RMS Output Noise Voltage (% of VO) TA = 25°C f =10Hz to 10KHz TA = 125°C 1000Hrs Temperature Stability Long Term Stability 0.01 60 0.04 %/W 75 dB 0.003 % 0.5 0.5 % % NOTE 1: See short-circuit current curve for available output current at fixed dropout. 7/20 LD1086 SERIES ELECTRICAL CHARACTERISTICS OF LD1086#80 (VI=11V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO Parameter Output Voltage (note 1) Test Conditions IO = 0 mA TJ = 25°C IO = 0 to 1.5A ∆VO ∆VO Line Regulation Load Regulation Min. VI = 9.8 to 30V IO = 0 mA VI = 9.8 to 20V IO = 0 mA VI = 9.8 to 20V IO = 0 to 1.5A 8 8.08 V 8 8.16 V TJ = 25°C TJ = 25°C 18 mV 18 mV 8 30 mV 12 60 V IO =1.5A 1.3 1.5 V 5 10 mA Iq Quiescent Current VI ≤ 30V Short Circuit Current VI - VO = 5V 1.5 VI - VO = 25V 0.04 Termal Regulation TA = 25°C, 30ms pulse Supply Voltage Rejection f = 120 Hz, CO = 25 µF, IO = 1.5A VI = 13 ± 3V RMS Output Noise Voltage (% of VO) TA = 25°C f =10Hz to 10KHz TA = 125°C 1000Hrs Temperature Stability Long Term Stability 1 2 IO = 0 to 1.5A Isc S S Unit 7.92 Dropout Voltage eN Max. 7.84 Vd SVR Typ. 2 0.2 0.01 54 A A 0.04 %/W 71 dB 0.003 % 0.5 0.5 % % NOTE 1: See short-circuit current curve for available output current at fixed dropout. ELECTRICAL CHARACTERISTICS OF LD1086#90 (VI=12V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO Parameter Output Voltage (note 1) Test Conditions IO = 0 mA IO = 0 to 1.5A TJ = 25°C VI = 11 to 30V Min. Typ. Max. Unit 8.91 9 9.09 V 8.82 ∆VO Line Regulation ∆VO Load Regulation Vd Dropout Voltage Iq Quiescent Current VI ≤ 30V Isc Short Circuit Current VI - VO = 5V 1.5 VI - VO = 25V 0.05 SVR eN S S IO = 0 mA VI = 11 to 20V IO = 0 mA VI = 11 to 20V IO = 0 to 1.5A TJ = 25°C TJ = 25°C V 20 mV 2 20 mV 8 30 mV 12 60 V IO = 1.5A 1.3 1.5 V 5 10 mA TA = 25°C, 30ms pulse Supply Voltage Rejection f = 120 Hz, CO = 25 µF, IO = 1.5A VI = 14 ± 3V RMS Output Noise Voltage (% of VO) TA = 25°C f =10Hz to 10KHz TA = 125°C 1000Hrs NOTE 1: See short-circuit current curve for available output current at fixed dropout. 8/20 9.18 IO = 0 to 1.5A Termal Regulation Temperature Stability Long Term Stability 9 1 2 0.2 0.01 54 A A 0.04 %/W 70 dB 0.003 % 0.5 0.5 % % LD1086 SERIES ELECTRICAL CHARACTERISTICS OF LD1086#120 (VI=15V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO Parameter Output Voltage (note 1) Test Conditions IO = 0 mA TJ = 25°C IO = 0 to 1.5A ∆VO ∆VO Line Regulation Load Regulation Min. VI = 13.8 to 30V IO = 0 mA VI = 13.8 to 25V IO = 0 mA VI = 13.8 to 25V IO = 0 to 1.5A 12 12.12 V 12 12.24 V TJ = 25°C TJ = 25°C 25 mV 25 mV 12 36 mV 24 72 V IO = 1.5A 1.3 1.5 V 5 10 mA Iq Quiescent Current VI ≤ 30V Short Circuit Current VI - VO = 5V 1.5 VI - VO = 25V 0.05 Termal Regulation TA = 25°C, 30ms pulse Supply Voltage Rejection f = 120 Hz, CO = 25 µF, IO = 1.5A VI = 17 ± 3V RMS Output Noise Voltage (% of VO) TA = 25°C f =10Hz to 10KHz TA = 125°C 1000Hrs Temperature Stability Long Term Stability 1 2 IO = 0 to 1.5A Isc S S Unit 11.88 Dropout Voltage eN Max. 11.76 Vd SVR Typ. 2 0.2 0.01 54 A A 0.04 %/W 66 dB 0.003 % 0.5 0.5 % % NOTE 1: See short-circuit current curve for available output current at fixed dropout. ELECTRICAL CHARACTERISTICS OF LD1086# (VI=4.25V, C I = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO ∆VO ∆VO Vd IO(min) Isc Parameter Output Voltage (note 1) Line Regulation Load Regulation Test Conditions Min. Typ. Max. Unit TJ = 25°C 1.237 1.25 1.263 V IO = 10mA to 1.5A VI = 2.85 to 30V 1.225 1.25 1.275 V IO = 10mA IO = 10mA VI = 2.8 to 16.5V TJ = 25°C 0.015 0.2 % IO = 10mA VI = 2.8 to 16.5V 0.035 0.2 % IO = 10mA to 1.5A TJ = 25°C 0.1 0.3 % IO = 0 to 1.5A 0.2 0.4 % Dropout Voltage IO = 1.5A 1.3 1.5 V Minimum Load Current VI = 30V 3 10 mA Short Circuit Current VI - VO = 5V 1.5 VI - VO = 25V 0.05 Termal Regulation TA = 25°C, 30ms pulse SVR Supply Voltage Rejection f = 120 Hz, IO = 1.5A CO = 25 µF, CADJ = 25 µF, VI = 6.25 ± 3V IADJ Adjust Pin Current VI = 4.25V IO = 10 mA ∆IADJ Adjust Pin Current Change eN RMS Output Noise Voltage (% of VO) IO = 10mA to 1.5A VI = 2.8 to 16.5V (note 1) TA = 25°C f =10Hz to 10KHz S S Temperature Stability Long Term Stability TA = 125°C 1000Hrs 2.3 0.2 0.01 60 A A 0.04 88 %/W dB 40 120 µA 0.2 5 µA 0.003 % 0.5 0.5 % % NOTE 1: See short-circuit current curve for available output current at fixed dropout. 9/20 LD1086 SERIES TYPICAL CHARACTERISTICS (unless otherwise specified Tj = 25°C, CI=CO=10µF) Figure 1 : Output Voltage vs Temperature Figure 4 : Short Circuit Current vs Dropout Voltage Figure 2 : Output Voltage vs Temperature Figure 5 : Line Regulation vs Temperature Figure 3 : Output Voltage vs Temperature Figure 6 : Load Regulation vs Temperature 10/20 LD1086 SERIES Figure 7 : Dropout Voltage vs Temperature Figure 10 : Adjust Pin Current vs Temperature Figure 8 : Dropout Voltage vs Output Current Figure 11 : Adjust Pin Current vs Output Current Figure 9 : Adjust Pin Current vs Input Voltage Figure 12 : Quiescent Current vs Output Current 11/20 LD1086 SERIES Figure 13 : Quiescent Current vs Input Voltage Figure 16 : Supply Voltage Rejection vs Temperature Figure 14 : Supply Voltage Rejection vs Output Current Figure 17 : Minimum Load Current vs Temperature Figure 15 : Supply Voltage Rejection vs Frequency Figure 18 : Stability for Adjustable 12/20 LD1086 SERIES Figure 19 : Stability for 2.85V Figure 22 : Line Transient VI=12 to 13V, IO=200mA, CI = 1µF(tant), CO=10µF(tant), No CADJ Figure 20 : Stability for 12V Figure 23 : Line Transient VI=12 to 13V, IO=200mA, CI = 1µF(tant), CO=10µF(tant), CADJ =1µF Figure 21 : Line Transient Figure 24 : Load Transient VI=12 to 13V, IO=200mA, CI = 1µF(tant), CO=10µF(tant), No CADJ VI=13V, IO=0.1 to 1.5A, CI = 1µF(tant), CO=10µF(tant) CADJ =1µF 13/20 LD1086 SERIES Figure 25 : Load Transient Figure 26 : Thermal Protection VI=13V, IO=0.1 to 1.5A, CI = 1µF(tant), CO=10µF(tant) CADJ =1µF VO=2.85 V 14/20 LD1086 SERIES TO-220 MECHANICAL DATA DIM. mm. MIN. TYP inch MAX. MIN. TYP. MAX. A 4.40 4.60 0.173 0.181 C 1.23 1.32 0.048 0.051 D 2.40 2.72 0.094 0.107 D1 1.27 0.050 E 0.49 0.70 0.019 0.027 F 0.61 0.88 0.024 0.034 F1 1.14 1.70 0.044 0.067 F2 1.14 1.70 0.044 0.067 G 4.95 5.15 0.194 0.203 G1 2.4 2.7 0.094 0.106 H2 10.0 10.40 0.393 0.409 L2 16.4 0.645 L4 13.0 14.0 0.511 0.551 L5 2.65 2.95 0.104 0.116 L6 15.25 15.75 0.600 0.620 L7 6.2 6.6 0.244 0.260 L9 3.5 3.93 0.137 0.154 DIA. 3.75 3.85 0.147 0.151 P011C 15/20 LD1086 SERIES D2PAK MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 4.4 4.6 0.173 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.7 0.93 0.027 0.036 B2 1.14 1.7 0.044 0.067 C 0.45 0.6 0.017 0.023 C2 1.23 1.36 0.048 0.053 D 8.95 9.35 0.352 0.368 10.4 0.393 D1 E 8 10 E1 0.315 8.5 0.409 0.335 G 4.88 5.28 0.192 0.208 L 15 15.85 0.590 0.624 L2 1.27 1.4 0.050 0.055 L3 1.4 1.75 0.055 0.068 M 2.4 3.2 0.094 R V2 0.4 0˚ 0.126 0.016 8˚ 0˚ 8˚ P011P6G 16/20 LD1086 SERIES D2PAK/A MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 4.40 4.60 0.173 0.181 A1 2.49 2.69 0.098 0.106 B 0.7 0.93 0.027 0.036 B2 1.14 1.7 0.044 0.067 C 0.45 0.60 0.017 0.023 C2 1.21 1.36 0.047 0.053 D 8.95 9.35 0.352 0.368 E 10 10.4 0.393 0.409 G 4.88 5.28 0.192 0.208 L 15 15.85 0.590 0.106 L2 1.27 1.4 0.050 0.055 17/20 LD1086 SERIES DPAK MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 2.2 2.4 0.086 0.094 A1 0.9 1.1 0.035 0.043 A2 0.03 0.23 0.001 0.009 B 0.64 0.9 0.025 0.035 B2 5.2 5.4 0.204 0.212 C 0.45 0.6 0.017 0.023 C2 0.48 0.6 0.019 0.023 D 6 6.2 0.236 0.244 E 6.4 6.6 0.252 0.260 G 4.4 4.6 0.173 0.181 H 9.35 10.1 0.368 0.397 L2 L4 0.8 0.6 0.031 1 0.023 0.039 0068772-B 18/20 LD1086 SERIES Tape & Reel DPAK-PPAK MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. 330 13.0 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 MAX. 0.504 0.512 14.4 0.519 0.567 Ao 6.80 6.90 7.00 0.268 0.272 0.2.76 Bo 10.40 10.50 10.60 0.409 0.413 0.417 Ko 2.55 2.65 2.75 0.100 0.104 0.105 Po 3.9 4.0 4.1 0.153 0.157 0.161 P 7.9 8.0 8.1 0.311 0.315 0.319 19/20 LD1086 SERIES Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2003 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 20/20