STMicroelectronics LD1117DT33TR Low drop fixed and adjustable positive voltage regulator Datasheet

LD1117 series
Low drop fixed and adjustable positive voltage regulators
Feature summary
■
Low dropout voltage (1V TYP.)
■
2.85V Device performances are suitable for
SCSI-2 active termination
■
Output current up to 800 mA
■
Fixed output voltage of: 1.2V, 1.8V, 2.5V,
2.85V, 3.0V, 3.3V, 5.0V
■
Adjustable version availability (Vrel=1.25V)
■
Internal current and thermal limit
■
Available in ± 1% (at 25°C) and 2% in full
temperature range
■
Supply voltage rejection: 75dB (typ.)
DPAK
TO-220
SOT-223
Description
The LD1117 is a LOW DROP Voltage Regulator
able to provide up to 800mA of Output Current,
available even in adjustable version (Vref=1.25V).
Concerning fixed versions, are offered the
following Output Voltages: 1.2V,1.8V,2.5V,2.85V,
3.0V 3.3V and 5.0V. The 2.85V type is ideal for
SCSI-2 lines active termination. The device is
supplied in: SOT-223, DPAK, SO-8 and TO-220.
SO-8
The SOT-223 and DPAK surface mount packages
optimize the thermal characteristics even offering
a relevant space saving effect. High efficiency is
assured by NPN pass transistor. In fact in this
case, unlike than PNP one, the Quiescent Current
flows mostly into the load. Only a very common
10µF minimum capacitor is needed for stability.
On chip trimming allows the regulator to reach a
very tight output voltage tolerance, within ± 1% at
25°C. The ADJUSTABLE LD1117 is pin to pin
compatible with the other standard. Adjustable
voltage regulators maintaining the better
performances in terms of Drop and Tolerance.
Block diagram
December 2006
Rev. 20
1/38
www.st.com
38
LD1117 series
Contents
1
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3
Schematic application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5
Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6
LD1117 Adjustable: Application note . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
8
Order code
9
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
2/38
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
LD1117 series
Pin configuration
1
Pin configuration
Figure 1.
Pin connections (top view)
SOT-223
DPAK
Note:
SO-8
TO-220
The TAB is connected to the VOUT.
3/38
Maximum ratings
LD1117 series
2
Maximum ratings
Table 1.
Absolute maximum ratings
Symbol
Parameter
Unit
VIN
DC Input Voltage
15
V
PTOT
Power Dissipation
12
W
TSTG
Storage Temperature Range
-40 to +150
°C
-40 to +150
°C
TOP
Operating Junction Temperature Range
0 to +150
°C
for C Version
Table 2.
Symbol
for standard Version
Thermal Data
Parameter
RthJC
Thermal Resistance Junction-case
RthJA
Thermal Resistance Junction-ambient
4/38
Value
SOT-223
SO-8
DPAK
TO-220
Unit
15
20
8
3
°C/W
50
°C/W
LD1117 series
3
Schematic application
Figure 2.
Application circuit (for 1.2V)
Figure 3.
Application circuit (for other fixed output voltages)
Schematic application
5/38
Electrical characteristics
LD1117 series
4
Electrical characteristics
Table 3.
Electrical characteristics of LD1117#12
(refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF, R = 120 Ω between GND and OUT
pins, unless otherwise specified).
Symbol
Parameter
Test
Min.
Typ.
Max.
Unit
VO
Output voltage
Vin = 3.2 V, IO = 10 mA, TJ = 25°C
1.188
1.20
1.212
V
VO
Reference voltage
IO = 10 to 800 mA
Vin - VO= 1.4 to 10 V
1.140
1.20
1.260
V
∆VO
Line regulation
Vin - VO = 1.5 to 13.75 V, IO = 10 mA
0.035
0.2
%
∆VO
Load regulation
Vin - VO = 3 V, IO = 10 to 800 mA
0.1
0.4
%
∆VO
Temperature stability
∆VO
Long term stability
Vin
Operating input voltage
Iadj
Adjustment pin current
Vin ≤15 V
Adjustment pin current change
1000 hrs, TJ = 125°C
0.5
%
0.3
%
15
V
60
120
µA
Vin - VO = 1.4 to 10 V
IO = 10 to 800 mA
1
5
µA
Minimum load current
Vin = 15 V
2
5
mA
IO
Output current
Vin - VO = 5 V, TJ = 25°C
950
1300
mA
eN
Output noise (%VO)
B =10Hz to 10KHz, TJ = 25°C
Supply voltage rejection
IO = 40 mA, f = 120Hz, TJ = 25°C
Vin - VO = 3 V, Vripple = 1 VPP
∆Iadj
IO(min)
SVR
Vd
Dropout voltage
Thermal regulation
6/38
800
60
0.003
%
75
dB
IO = 100 mA
1
1.1
IO = 500 mA
1.05
1.15
IO = 800 mA
1.10
1.2
Ta = 25°C, 30ms Pulse
0.01
0.1
V
%/W
LD1117 series
Table 4.
Symbol
Electrical characteristics
Electrical characteristics of LD1117#18
(refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF, unless otherwise specified).
Parameter
Test
Min.
Typ.
Max.
Unit
1.8
1.82
V
1.84
V
VO
Output voltage
Vin = 3.8 V, IO = 10 mA, TJ = 25°C
1.78
VO
Output voltage
IO = 0 to 800 mA, Vin = 3.3 to 8 V
1.76
∆VO
Line regulation
Vin = 3.3 to 8 V, IO = 0 mA
1
6
mV
∆VO
Load regulation
Vin = 3.3 V, IO = 0 to 800 mA
1
10
mV
∆VO
Temperature stability
∆VO
Long term stability
1000 hrs, TJ = 125°C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤8 V
IO
Output current
Vin = 6.8 V, TJ = 25°C
eN
Output noise voltage
B =10Hz to 10KHz, TJ = 25°C
Supply voltage rejection
IO = 40 mA, f = 120Hz, TJ = 25°C
Vin = 5.5 V, Vripple = 1 VPP
SVR
Vd
Dropout voltage
Thermal regulation
Table 5.
Symbol
800
60
0.5
%
0.3
%
10
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA
1
1.1
IO = 500 mA
1.05
1.15
IO = 800 mA
1.10
1.2
Ta = 25°C, 30ms Pulse
0.01
0.1
V
%/W
Electrical characteristics of LD1117#25
(refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF, unless otherwise specified).
Parameter
Test
Min.
Typ.
Max.
Unit
2.5
2.525
V
2.55
V
VO
Output voltage
Vin = 4.5 V, IO = 10 mA, TJ = 25°C
2.475
VO
Output voltage
IO = 0 to 800 mA, Vin = 3.9 to 10 V
2.45
∆VO
Line regulation
Vin = 3.9 to 10 V, IO = 0 mA
1
6
mV
∆VO
Load regulation
Vin = 3.9 V, IO = 0 to 800 mA
1
10
mV
∆VO
Temperature stability
∆VO
Long term stability
1000 hrs, TJ = 125°C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤10 V
IO
Output current
Vin = 7.5 VTJ = 25°C
eN
Output noise voltage
B =10Hz to 10KHz, TJ = 25°C
Supply voltage rejection
IO = 40 mA, f = 120Hz, TJ = 25°C
Vin = 5.5 V, Vripple = 1 VPP
SVR
Vd
Dropout voltage
Thermal regulation
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA
1
1.1
IO = 500 mA
1.05
1.15
IO = 800 mA
1.10
1.2
Ta = 25°C, 30ms Pulse
0.01
0.1
V
%/W
7/38
Electrical characteristics
Table 6.
Symbol
LD1117 series
Electrical characteristics of LD1117#28
(refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF, unless otherwise specified).
Parameter
Test
Min.
Typ.
Max.
Unit
2.85
2.88
V
2.91
V
VO
Output voltage
Vin = 4.85 V, IO = 10 mA, TJ = 25°C
2.82
VO
Output voltage
IO = 0 to 800 mA, Vin = 4.25 to 10 V
2.79
∆VO
Line regulation
Vin = 4.25 to 10 V, IO = 0 mA
1
6
mV
∆VO
Load regulation
Vin = 4.25 V, IO = 0 to 800 mA
1
10
mV
∆VO
Temperature stability
∆VO
Long term stability
1000 hrs, TJ = 125°C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤10 V
IO
Output current
Vin = 7.85 VTJ = 25°C
eN
Output noise voltage
B =10Hz to 10KHz, TJ = 25°C
Supply voltage rejection
IO = 40 mA, f = 120Hz, TJ = 25°C
Vin = 5.85 V, Vripple = 1 VPP
SVR
Vd
Dropout voltage
Thermal regulation
8/38
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA
1
1.1
IO = 500 mA
1.05
1.15
IO = 800 mA
1.10
1.2
Ta = 25°C, 30ms Pulse
0.01
0.1
V
%/W
LD1117 series
Table 7.
Symbol
Electrical characteristics
Electrical characteristics of LD1117#30
(refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF, unless otherwise specified).
Parameter
Test
Min.
Typ.
Max.
Unit
3
3.03
V
3.06
V
VO
Output voltage
Vin = 5 V, IO = 10 mA, TJ = 25°C
2.97
VO
Output voltage
IO = 0 to 800 mA, Vin = 4.5 to 10 V
2.94
∆VO
Line regulation
Vin = 4.5 to 12 V, IO = 0 mA
1
6
mV
∆VO
Load regulation
Vin = 4.5 V, IO = 0 to 800 mA
1
10
mV
∆VO
Temperature stability
∆VO
Long term stability
1000 hrs, TJ = 125°C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤12 V
IO
Output current
Vin = 8 V, TJ = 25°C
eN
Output noise voltage
B =10Hz to 10KHz,TJ = 25°C
Supply voltage rejection
IO = 40 mA, f = 120Hz, TJ = 25°C
Vin = 6 V, Vripple = 1 VPP
SVR
Vd
Dropout voltage
Thermal regulation
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA
1
1.1
IO = 500 mA
1.05
1.15
IO = 800 mA
1.10
1.2
Ta = 25°C, 30ms Pulse
0.01
0.1
V
%/W
9/38
Electrical characteristics
Table 8.
Symbol
LD1117 series
Electrical characteristics of LD1117#33
(refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF, unless otherwise specified).
Parameter
Test
Min.
Typ.
Max.
Unit
3.3
3.333
V
3.365
V
VO
Output voltage
Vin = 5.3 V, IO = 10 mA, TJ = 25°C
3.267
VO
Output voltage
IO = 0 to 800 mA, Vin = 4.75 to 10 V
3.235
∆VO
Line regulation
Vin = 4.75 to 15 V, IO = 0 mA
1
6
mV
∆VO
Load regulation
Vin = 4.75 V, IO = 0 to 800 mA
1
10
mV
∆VO
Temperature stability
∆VO
Long term stability
1000 hrs, TJ = 125°C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤15 V
IO
Output current
Vin = 8.3 V, TJ = 25°C
eN
Output noise voltage
B =10Hz to 10KHz, TJ = 25°C
Supply voltage rejection
IO = 40 mA, f = 120Hz, TJ = 25°C
Vin = 6.3 V, Vripple = 1 VPP
SVR
Vd
Dropout voltage
Thermal regulation
10/38
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA
1
1.1
IO = 500 mA
1.05
1.15
IO = 800 mA
1.10
1.2
Ta = 25°C, 30ms Pulse
0.01
0.1
V
%/W
LD1117 series
Table 9.
Symbol
Electrical characteristics
Electrical characteristics of LD1117#50
(refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF, unless otherwise specified).
Parameter
Test
Min.
Typ.
Max.
Unit
5
5.05
V
5.1
V
VO
Output voltage
Vin = 7 V, IO = 10 mA, TJ = 25°C
4.95
VO
Output voltage
IO = 0 to 800 mA, Vin = 6.5 to 15 V
4.9
∆VO
Line regulation
Vin = 6.5 to 15 V, IO = 0 mA
1
10
mV
∆VO
Load regulation
Vin = 6.5 V, IO = 0 to 800 mA
1
15
mV
∆VO
Temperature stability
∆VO
Long term stability
1000 hrs, TJ = 125°C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤15 V
IO
Output current
Vin = 10 V, TJ = 25°C
eN
Output noise voltage
B =10Hz to 10KHz, TJ = 25°C
Supply voltage rejection
IO = 40 mA, f = 120Hz, TJ = 25°C
Vin = 8 V, Vripple = 1 VPP
SVR
Vd
Dropout voltage
Thermal regulation
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA
1
1.1
IO = 500 mA
1.05
1.15
IO = 800 mA
1.10
1.2
Ta = 25°C, 30ms Pulse
0.01
0.1
V
%/W
11/38
Electrical characteristics
Table 10.
Symbol
LD1117 series
Electrical characteristics of LD1117 (Adjustable)
(refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF, unless otherwise specified).
Parameter
Test
Min.
Typ.
Max.
Unit
1.238
1.25
1.262
V
1.275
V
0.035
0.2
%
0.1
0.4
%
Vref
Reference voltage
Vin - VO = 2 V, IO = 10 mA, TJ = 25°C
Vref
Reference voltage
IO = 10 to 800 mA, Vin - VO = 1.4 to 10 V 1.225
∆VO
Line regulation
Vin - VO = 1.5 to 13.75 V, IO = 10 mA
∆VO
Load regulation
Vin - VO = 3 V, IO = 10 to 800 mA
∆VO
Temperature stability
∆VO
Long term stability
Vin
Operating input voltage
Iadj
Adjustment pin current
1000 hrs, TJ = 125°C
0.5
%
0.3
%
15
V
Vin ≤15 V
60
120
µA
Adjustment pin current change Vin - VO = 1.4 to 10 V, IO = 10 to 800 mA
1
5
µA
Minimum load current
Vin = 15 V
2
5
mA
IO
Output current
Vin - VO = 5 V, TJ = 25°C
950
1300
mA
eN
Output noise (%VO)
B =10Hz to 10KHz, TJ = 25°C
Supply voltage rejection
IO = 40 mA, f = 120Hz, TJ = 25°C
Vin - VO = 3 V, Vripple = 1 VPP
∆Iadj
IO(min)
SVR
Vd
Dropout voltage
Thermal regulation
12/38
800
60
0.003
%
75
dB
IO = 100 mA
1
1.1
IO = 500 mA
1.05
1.15
IO = 800 mA
1.10
1.2
Ta = 25°C, 30ms Pulse
0.01
0.1
V
%/W
LD1117 series
Table 11.
Symbol
Electrical characteristics
Electrical characteristics of LD1117#12C
(refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF, R = 120 Ω between GND and OUT
pins, unless otherwise specified).
Parameter
Test
Min.
Typ.
Max.
Unit
Vref
Reference voltage
Vin - VO= 2V, IO = 10 mA, TJ = 25°C
1.176
1.20
1.224
V
Vref
Reference voltage
IO = 10 to 800 mA, Vin - VO= 1.4 to
10 V
1.120
1.20
1.280
V
∆VO
Line regulation
Vin - VO = 1.5 to 13.75 V, IO = 10 mA
1
%
∆VO
Load regulation
Vin - VO = 3 V, IO = 10 to 800 mA
1
%
∆VO
Temperature stability
∆VO
Long term stability
Vin
Operating input voltage
Iadj
Adjustment pin current
Vin ≤15 V
Adjustment pin current change
1000 hrs, TJ = 125°C
0.5
%
0.3
%
15
V
60
120
µA
Vin - VO = 1.4 to 10 V
IO = 10 to 800 mA
1
5
µA
Minimum load current
Vin = 15 V
2
5
mA
IO
Output current
Vin - VO = 5 V, TJ = 25°C
950
1300
mA
eN
Output noise (%VO)
B =10Hz to 10KHz, TJ = 25°C
Supply voltage rejection
IO = 40 mA, f = 120Hz, TJ = 25°C
Vin - VO = 3 V, Vripple = 1 VPP
∆Iadj
IO(min)
SVR
Vd
Dropout voltage
Thermal regulation
800
60
0.003
%
75
dB
IO = 100 mA, TJ = 0 to 125°C
1
1.1
IO = 500 mA, TJ = 0 to 125°C
1.05
1.2
IO = 800 mA, TJ = 0 to 125°C
1.10
1.3
Ta = 25°C, 30ms Pulse
0.01
0.1
V
%/W
13/38
Electrical characteristics
Table 12.
Symbol
LD1117 series
Electrical characteristics of LD1117#18C
(refer to the test circuits, TJ = -40 to 125°C, CO = 10 µF, unless otherwise specified).
Parameter
Test
Min.
Typ.
Max.
Unit
1.8
1.84
V
1.87
V
VO
Output voltage
Vin = 3.8 V, IO = 10 mA, TJ = 25°C
1.76
VO
Output voltage
IO = 0 to 800 mA, Vin = 3.9 to 10 V
1.73
∆VO
Line regulation
Vin = 3.3 to 8 V, IO = 0 mA
1
30
mV
∆VO
Load regulation
Vin = 3.3 V, IO = 0 to 800 mA
1
30
mV
∆VO
Temperature stability
∆VO
Long term stability
1000 hrs, TJ = 125°C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤8 V
IO
Output current
Vin = 6.8 VTJ = 25°C
eN
Output noise voltage
B =10Hz to 10KHz, TJ = 25°C
Supply voltage rejection
IO = 40 mA, f = 120Hz, TJ = 25°C
Vin = 5.5 V, Vripple = 1 VPP
SVR
Vd
Vd
Dropout voltage
Dropout voltage
Thermal regulation
14/38
800
60
0.5
%
0.3
%
10
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA, TJ = 0 to 125°C
1
1.1
IO = 500 mA, TJ = 0 to 125°C
1.05
1.15
IO = 800 mA, TJ = 0 to 125°C
1.10
1.2
IO = 100 mA
1.1
IO = 500 mA
1.2
IO = 800 mA
1.3
Ta = 25°C, 30ms Pulse
0.01
0.1
V
V
%/W
LD1117 series
Table 13.
Symbol
Electrical characteristics
Electrical characteristics of LD1117#25C
(refer to the test circuits, TJ = -40 to 125°C, CO = 10 µF, unless otherwise specified).
Parameter
Test
Min.
Typ.
Max.
Unit
2.5
2.55
V
2.6
V
VO
Output voltage
Vin = 4.5 V, IO = 10 mA, TJ = 25°C
2.45
VO
Output voltage
IO = 0 to 800 mA, Vin = 3.9 to 10 V
2.4
∆VO
Line regulation
Vin = 3.9 to 10 V, IO = 0 mA
1
30
mV
∆VO
Load regulation
Vin = 3.9 V, IO = 0 to 800 mA
1
30
mV
∆VO
Temperature stability
∆VO
Long term stability
1000 hrs, TJ = 125°C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤10 V
IO
Output current
Vin = 7.5 VTJ = 25°C
eN
Output noise voltage
B =10Hz to 10KHz, TJ = 25°C
Supply voltage rejection
IO = 40 mA, f = 120Hz, TJ = 25°C
Vin = 5.5 V, Vripple = 1 VPP
SVR
Vd
Vd
Dropout voltage
Dropout voltage
Thermal regulation
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA, TJ = 0 to 125°C
1
1.1
IO = 500 mA, TJ = 0 to 125°C
1.05
1.15
IO = 800 mA, TJ = 0 to 125°C
1.10
1.2
IO = 100 mA
1.1
IO = 500 mA
1.2
IO = 800 mA
1.3
Ta = 25°C, 30ms Pulse
0.01
0.1
V
V
%/W
15/38
Electrical characteristics
Table 14.
Symbol
LD1117 series
Electrical characteristics of LD1117#30C
(refer to the test circuits, TJ = -40 to 125°C, CO = 10 µF, unless otherwise specified).
Parameter
Test
Min.
Typ.
Max.
Unit
3
3.06
V
3.12
V
VO
Output voltage
Vin = 5 V, IO = 10 mA, TJ = 25°C
2.94
VO
Output voltage
IO = 0 to 800 mA, Vin = 4.5 to 10 V
2.88
∆VO
Line regulation
Vin = 4.5 to 12 V, IO = 0 mA
1
30
mV
∆VO
Load regulation
Vin = 4.5 V, IO = 0 to 800 mA
1
30
mV
∆VO
Temperature stability
∆VO
Long term stability
1000 hrs, TJ = 125°C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤12 V
IO
Output current
Vin = 8 V, TJ = 25°C
eN
Output noise voltage
B =10Hz to 10KHz, TJ = 25°C
Supply voltage rejection
IO = 40 mA, f = 120Hz, TJ = 25°C
Vin = 6 V, Vripple = 1 VPP
SVR
Vd
Vd
Dropout voltage
Dropout voltage
Thermal regulation
16/38
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA, TJ = 0 to 125°C
1
1.1
IO = 500 mA, TJ = 0 to 125°C
1.05
1.15
IO = 800 mA, TJ = 0 to 125°C
1.10
1.2
IO = 100 mA
1.1
IO = 500 mA
1.2
IO = 800 mA
1.3
Ta = 25°C, 30ms Pulse
0.01
0.1
V
V
%/W
LD1117 series
Table 15.
Symbol
Electrical characteristics
Electrical characteristics of LD1117#33C
(refer to the test circuits, TJ = -40 to 125°C, CO = 10 µF, unless otherwise specified).
Parameter
Test
Min.
Typ.
Max.
Unit
3.3
3.36
V
3.44
V
VO
Output voltage
Vin = 5.3 V, IO = 10 mA, TJ = 25°C
3.24
VO
Output voltage
IO = 0 to 800 mA, Vin = 4.75 to 10 V
3.16
∆VO
Line regulation
Vin = 4.75 to 15 V, IO = 0 mA
1
30
mV
∆VO
Load regulation
Vin = 4.75 V, IO = 0 to 800 mA
1
30
mV
∆VO
Temperature stability
∆VO
Long term stability
1000 hrs, TJ = 125°C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤15 V
IO
Output current
Vin = 8.3 V, TJ = 25°C
eN
Output noise voltage
B =10Hz to 10KHz, TJ = 25°C
Supply voltage rejection
IO = 40 mA, f = 120Hz, TJ = 25°C
Vin = 6.3 V, Vripple = 1 VPP
SVR
Vd
Vd
Dropout voltage
Dropout voltage
Thermal regulation
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA, TJ = 0 to 125°C
1
1.1
IO = 500 mA, TJ = 0 to 125°C
1.05
1.15
IO = 800 mA, TJ = 0 to 125°C
1.10
1.2
IO = 100 mA
1.1
IO = 500 mA
1.2
IO = 800 mA
1.3
Ta = 25°C, 30ms Pulse
0.01
0.1
V
V
%/W
17/38
Electrical characteristics
Table 16.
Symbol
LD1117 series
Electrical characteristics of LD1117#50C
(refer to the test circuits, TJ = -40 to 125°C, CO = 10 µF, unless otherwise specified).
Parameter
Test
Min.
Typ.
Max.
Unit
5
5.1
V
5.2
V
VO
Output voltage
Vin = 7 V, IO = 10 mA, TJ = 25°C
4.9
VO
Output voltage
IO = 0 to 800 mA, Vin = 6.5 to 15 V
4.8
∆VO
Line regulation
Vin = 6.5 to 15 V, IO = 0 mA
1
50
mV
∆VO
Load regulation
Vin = 6.5 V, IO = 0 to 800 mA
1
50
mV
∆VO
Temperature stability
∆VO
Long term stability
1000 hrs, TJ = 125°C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤15 V
IO
Output current
Vin = 10 V, TJ = 25°C
eN
Output noise voltage
B =10Hz to 10KHz, TJ = 25°C
Supply voltage rejection
IO = 40 mA, f = 120Hz, TJ = 25°C
Vin = 8 V, Vripple = 1 VPP
SVR
Vd
Vd
Dropout voltage
Dropout voltage
Thermal regulation
18/38
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA, TJ = 0 to 125°C
1
1.1
IO = 500 mA, TJ = 0 to 125°C
1.05
1.15
IO = 800 mA, TJ = 0 to 125°C
1.10
1.2
IO = 100 mA
1.1
IO = 500 mA
1.2
IO = 800 mA
1.3
Ta = 25°C, 30ms Pulse
0.01
0.1
V
V
%/W
LD1117 series
Table 17.
Symbol
Electrical characteristics
Electrical characteristics of LD1117C (Adjustable)
(refer to the test circuits, TJ = -40 to 125°C, CO = 10 µF, unless otherwise specified).
Parameter
Test
Min.
Typ.
Max.
Unit
1.225
1.25
1.275
V
1.3
V
Vref
Reference voltage
Vin - VO = 2 V, IO = 10 mA, TJ = 25°C
Vref
Reference voltage
IO = 10 to 800 mA, Vin - VO= 1.4 to 10 V
∆VO
Line regulation
Vin - VO = 1.5 to 13.75 V, IO = 10 mA
1
%
∆VO
Load regulation
Vin - VO = 3 V, IO = 10 to 800 mA
1
%
∆VO
Temperature stability
∆VO
Long term stability
Vin
Operating input voltage
Iadj
Adjustment pin current
1.2
1000 hrs, TJ = 125°C
0.5
%
0.3
%
15
V
Vin ≤15 V
60
120
µA
Adjustment pin current change Vin - VO = 1.4 to 10 V, IO = 10 to 800 mA
1
10
µA
Minimum load current
Vin = 15 V
2
5
mA
IO
Output current
Vin - VO = 5 V, TJ = 25°C
950
1300
mA
eN
Output noise (%VO)
B =10Hz to 10KHz, TJ = 25°C
Supply voltage rejection
IO = 40 mA, f = 120Hz, TJ = 25°C
Vin - VO = 3 V, Vripple = 1 VPP
∆Iadj
IO(min)
SVR
Vd
Vd
Dropout voltage
Dropout voltage
Thermal regulation
800
60
0.003
%
75
dB
IO = 100 mA, TJ = 0 to 125°C
1
1.1
IO = 500 mA, TJ = 0 to 125°C
1.05
1.15
IO = 800 mA, TJ = 0 to 125°C
1.10
1.2
IO = 100 mA
1.1
IO = 500 mA
1.2
IO = 800 mA
1.3
Ta = 25°C, 30ms Pulse
0.01
0.1
V
V
%/W
19/38
Typical application
5
Typical application
Figure 4.
Negative supply
Figure 5.
Active terminator for SCSI-2 BUS
Figure 6.
Circuit for increasing output voltage
20/38
LD1117 series
LD1117 series
Figure 7.
Voltage Regulator With Reference
Figure 8.
Battery backed-up regulated supply
Typical application
21/38
Typical application
Figure 9.
22/38
Post-regulated dual supply
LD1117 series
LD1117 series
6
LD1117 Adjustable: Application note
LD1117 Adjustable: Application note
The LD1117 Adjustable has a thermal stabilized 1.25±0.012V reference voltage between
the OUT and ADJ pins. IADJ is 60µA typ. (120µA max.) and ∆IADJ is 1µA typ. (5µA max.).
R1 is normally fixed to 120W. From figure 10 we obtain:
VOUT = VREF + R2 (IADJ +IR1) = VREF + R2 (IADJ +VREF /R1) = VREF (1 + R2 / R1) + R2 x
IADJ.
In normal application R2 value is in the range of few kohm, so the R2 x IADJ product could
not be considered in the VOUT calculation; then the above expression becomes:
VOUT = VREF (1 + R2 / R1).
In order to have the better load regulation it is important to realize a good Kelvin connection
of R1 and R2 resistors. In particular R1 connection must be realized very close to OUT and
ADJ pin, while R2 ground connection must be placed as near as possible to the negative
Load pin. Ripple rejection can be improved by introducing a 10µF electrolytic capacitor
placed in parallel to the R2 resistor (see Fig. 11).
Figure 10. Adjustable output voltage application
Figure 11. Adjustable output voltage application with improved ripple rejection
23/38
Package mechanical data
7
LD1117 series
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a Lead-free second level interconnect. The category of
second Level Interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at: www.st.com.
24/38
LD1117 series
Package mechanical data
SOT-223 MECHANICAL DATA
mm.
mils
DIM.
MIN.
TYP
A
MAX.
MIN.
TYP.
1.8
A1
0.02
B
0.6
B1
MAX.
70.9
0.1
0.8
3.9
0.7
0.85
23.6
27.6
33.5
2.9
3
3.15
114.2
118.1
124.0
c
0.24
0.26
0.35
9.4
10.2
13.8
D
6.3
6.5
6.7
248.0
255.9
263.8
e
2.3
90.6
e1
4.6
181.1
E
3.3
3.5
3.7
129.9
137.8
145.7
H
6.7
7
7.3
263.8
275.7
287.5
V
10°
10°
0046067/H
25/38
Package mechanical data
LD1117 series
SO-8 MECHANICAL DATA
DIM.
mm.
MIN.
TYP
inch
MAX.
MIN.
TYP.
MAX.
A
1.35
1.75
0.053
0.069
A1
0.10
0.25
0.04
0.010
A2
1.10
1.65
0.043
0.065
B
0.33
0.51
0.013
0.020
C
0.19
0.25
0.007
0.010
D
4.80
5.00
0.189
0.197
E
3.80
4.00
0.150
0.157
e
1.27
0.050
H
5.80
6.20
0.228
0.244
h
0.25
0.50
0.010
0.020
L
0.40
1.27
0.016
0.050
k
ddd
8˚ (max.)
0.1
0.04
0016023/C
26/38
LD1117 series
Package mechanical data
Figure 12. DRAWING DIMENSION DPAK (TYPE STD-ST)
0068772/G
27/38
Package mechanical data
LD1117 series
Figure 13. DRAWING DIMENSION DPAK (TYPE FUJITSU-SUBCON.)
0068772/G
28/38
LD1117 series
Package mechanical data
Figure 14. DRAWING DIMENSION DPAK (TYPE IDS-SUBCON.)
0068772/G
29/38
Package mechanical data
Table 18.
LD1117 series
DPAK MECHANICAL DATA
DIM.
MIN.
TYPE STD-ST
TYPE FUJITSU-SUBCON.
TYPE IDS-SUBCON
mm.
mm.
mm.
TYP.
MAX.
MIN.
TYP.
MAX.
MIN.
TYP.
MAX.
2.30
2.35
2.19
2.38
A
2.20
2.40
2.25
A1
0.90
1.10
0.96
1.06
0.89
1.14
A2
0.03
0.23
0
0.10
0.03
0.23
b
0.64
0.90
0.76
0.86
0.64
0.88
b4
5.20
5.40
5.28
5.38
5.21
5.46
c
0.45
0.60
0.46
0.56
0.46
0.58
c2
0.48
0.60
0.46
0.56
0.46
0.58
D
6.00
6.20
6.05
6.15
5.97
6.22
5.27
5.47
D1
E
5.10
6.40
6.60
E1
4.70
e
2.28
2.23
4.40
4.60
H
9.35
10.10
L
1.00
2.80
L2
0.80
L4
0.60
R
V2
Note:
30/38
6.65
6.35
1.00
2.28
2.33
2.28
4.51
4.61
10.42
10.30
9.40
1.40
1.60
0.90
2.50
2.65
1.03
1.13
0.89
1.27
0.70
0.90
0.64
1.02
0.40
8°
6.73
4.70
9.90
0.20
0°
6.60
4.77
e1
L1
6.55
5.20
0°
0.20
8°
0°
The DPAK package coming from the two subcontractors (Fujitsu and IDS) are fully
compatible with the ST's package suggested footprint.
8°
LD1117 series
Package mechanical data
Figure 15. DPAK FOOTPRINT RECOMMENDED DATA
Table 19.
FOOTPRINT DATA
VALUES
mm.
inch.
A
6.70
0.264
B
6.70
0.64
C
1.8
0.070
D
3.0
0.118
E
1.60
0.063
F
2.30
0.091
G
2.30
0.091
31/38
Package mechanical data
LD1117 series
TO-220 MECHANICAL DATA
DIM.
mm.
MIN.
MAX.
MIN.
A
4.40
4.60
0.173
0.181
C
1.23
1.32
0.048
0.051
D
2.40
2.72
0.094
0.107
D1
TYP
inch
1.27
TYP.
MAX.
0.050
E
0.49
0.70
0.019
0.027
F
0.61
0.88
0.024
0.034
F1
1.14
1.70
0.044
0.067
F2
1.14
1.70
0.044
0.067
G
4.95
5.15
0.194
0.203
G1
2.4
2.7
0.094
0.106
H2
10.0
10.40
0.393
L2
16.4
0.409
0.645
L4
13.0
14.0
0.511
0.551
L5
2.65
2.95
0.104
0.116
L6
15.25
15.75
0.600
0.620
L7
6.2
6.6
0.244
0.260
L9
3.5
3.93
0.137
0.154
DIA.
3.75
3.85
0.147
0.151
P011C
32/38
LD1117 series
Package mechanical data
Tape & Reel SOT223 MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
A
MAX.
MIN.
TYP.
330
13.0
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
13.2
MAX.
0.504
0.512
14.4
0.519
0.567
Ao
6.73
6.83
6.93
0.265
0.269
0.273
Bo
7.32
7.42
7.52
0.288
0.292
0.296
Ko
1.78
2
0.070
Po
3.9
4.0
4.1
0.153
0.157
0.161
P
7.9
8.0
8.1
0.311
0.315
0.319
0.078
33/38
Package mechanical data
LD1117 series
Tape & Reel SO-8 MECHANICAL DATA
mm.
inch
DIM.
MIN.
A
MAX.
MIN.
330
13.2
TYP.
MAX.
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
34/38
TYP
0.504
22.4
0.519
0.882
Ao
8.1
8.5
0.319
0.335
Bo
5.5
5.9
0.216
0.232
Ko
2.1
2.3
0.082
0.090
Po
3.9
4.1
0.153
0.161
P
7.9
8.1
0.311
0.319
LD1117 series
Package mechanical data
Tape & Reel DPAK-PPAK MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
A
MAX.
MIN.
TYP.
330
13.0
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
13.2
MAX.
0.504
0.512
22.4
0.519
0.882
Ao
6.80
6.90
7.00
0.268
0.272
0.2.76
Bo
10.40
10.50
10.60
0.409
0.413
0.417
Ko
2.55
2.65
2.75
0.100
0.104
0.105
Po
3.9
4.0
4.1
0.153
0.157
0.161
P
7.9
8.0
8.1
0.311
0.315
0.319
35/38
Order code
LD1117 series
8
Order code
Table 20.
Order code
Part numbers
SOT-223
SO-8
DPAK
DPAK (T&R)
TO-220
Output
voltage
LD1117S12TR
LD1117D12TR (*)
LD1117DT12 (*)
LD1117DT12TR
LD1117V12 (*)
1.2 V
LD1117V12C (*)
1.2 V
LD1117V18
1.8 V
LD1117S12CTR (*) LD1117D12CTR (*) LD1117DT12C (*)
LD1117S18TR
LD1117D18TR (*)
LD1117S18CTR (*) LD1117D18CTR (*)
LD1117DT18
LD1117DT18C
LD1117DT18TR
LD1117DT18CTR LD1117V18C (*)
1.8 V
LD1117S25TR
LD1117D25TR (*)
LD1117DT25
LD1117DT25TR
LD1117V25
2.5 V
LD1117S25CTR
LD1117D25CTR (*)
LD1117DT25C
LD1117DT25CTR
LD1117V25C
2.5 V
LD1117S28TR
LD1117D28TR (*)
LD1117S30TR
LD1117D30TR (*)
LD1117S33TR
LD1117D33TR
LD1117DT33
LD1117DT33TR
LD1117V33
3.3 V
LD1117S33CTR
LD1117D33CTR
LD1117DT33C
LD1117DT33CTR
LD1117V33C
3.3 V
LD1117S50TR
LD1117D50TR
LD1117DT50
LD1117DT50TR
LD1117V50
5V
LD1117S50CTR
LD1117D50CTR (*)
LD1117DT50C
LD1117DT50CTR
LD1117STR
LD1117DTR (*)
LD1117DT
LD1117DTTR
LD1117V
ADJ FROM
1.25 TO 15V
LD1117SC-R
LD1117DC-R (*)
LD1117DTC (*)
LD1117DTC-R
LD1117VC (*)
ADJ FROM
1.25 TO 15V
(*) Available on request.
36/38
LD1117DT28TR
2.85 V
3V
5V
LD1117 series
Revision history
9
Revision history
Table 21.
Document revision history
Date
Revision
Changes
22-Sep-2004
15
Add new Part Number #12C; Typing Error: Note on table 2.
25-Oct-2004
16
Add Vref Reference Voltage on Table 12.
18-Jul-2005
17
The DPAK Mechanical Data has been updated.
25-Nov-2005
18
The TO220FM Package has been removed.
14-Dec-2005
19
The Top on Table 2 has been updated.
06-Dec-2006
20
DPAK mechanical data has been updated and add footprint data.
37/38
LD1117 series
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2006 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
38/38
Similar pages