LD1117 SERIES LOW DROP FIXED AND ADJUSTABLE POSITIVE VOLTAGE REGULATORS ■ ■ ■ ■ ■ ■ ■ ■ LOW DROPOUT VOLTAGE (1V TYP.) 2.85V DEVICE PERFORMANCES ARE SUITABLE FOR SCSI-2 ACTIVE TERMINATION OUTPUT CURRENT UP TO 800 mA FIXED OUTPUT VOLTAGE OF: 1.2V, 1.8V, 2.5V, 2.85V, 3.0V, 3.3V, 5.0V ADJUSTABLE VERSION AVAILABILITY (Vrel=1.25V) INTERNAL CURRENT AND THERMAL LIMIT AVAILABLE IN ± 1% (AT 25°C) AND 2% IN FULL TEMPERATURE RANGE SUPPLY VOLTAGE REJECTION: 75dB (TYP.) DESCRIPTION The LD1117 is a LOW DROP Voltage Regulator able to provide up to 800mA of Output Current, available even in adjustable version (Vref=1.25V). Concerning fixed versions, are offered the following Output Voltages: 1.2V,1.8V,2.5V,2.85V, 3.0V 3.3V and 5.0V. The 2.85V type is ideal for SCSI-2 lines active termination. The device is supplied in: SOT-223, DPAK, SO-8, TO-220 and TO-220FM. The SOT-223 and DPAK surface mount packages optimize the thermal characteristics even offering a relevant space saving effect. High efficiency is assured by NPN TO-220FM DPAK TO-220 SOT-223 SO-8 pass transistor. In fact in this case, unlike than PNP one, the Quiescent Current flows mostly into the load. Only a very common 10µF minimum capacitor is needed for stability. On chip trimming allows the regulator to reach a very tight output voltage tolerance, within ± 1% at 25°C. The ADJUSTABLE LD1117 is pin to pin compatible with the other standard. Adjustable voltage regulators maintaining the better performances in terms of Drop and Tolerance. Figure 1: Block Diagram October 2004 Rev. 16 1/28 LD1117 SERIES Figure 2: Pin Connection (top view) SOT-223 SO-8 TO-220 TO-220FM DPAK NOTE: The TAB is connected to the VOUT. Table 1: Order Codes SOT-223 SO-8 DPAK TO-220 TO-220FM LD1117S12 LD1117S12C (*) LD1117S18 LD1117S18C LD1117S25 LD1117S25C LD1117S28 LD1117S30 LD1117S30C LD1117S33 LD1117S33C LD1117S50 LD1117S50C LD1117S LD1117D12 (*) LD1117D12C (*) LD1117D18 LD1117D18C LD1117D25 LD1117D25C LD1117D28 LD1117D30 LD1117D30C LD1117D33 LD1117D33C LD1117D50 LD1117D50C LD1117D LD1117DT12 LD1117DT12C LD1117DT18 LD1117DT18C LD1117DT25 LD1117DT25C LD1117DT28 LD1117DT30 LD1117DT30C LD1117DT33 LD1117DT33C LD1117DT50 LD1117DT50C LD1117DT LD1117V12 (*) LD1117V12C (*) LD1117V18 LD1117V18C LD1117V25 LD1117V25C LD1117V28 LD1117V30 LD1117V30C LD1117V33 LD1117V33C LD1117V50 LD1117V50C LD1117V LD1117F12 (*) LD1117F12C (*) LD1117F18 LD1117F18C LD1117F25 LD1117F25C LD1117F28 LD1117F30 LD1117F30C LD1117F33 LD1117F33C LD1117F50 LD1117F50C LD1117F LD1117SC LD1117DC LD1117DTC LD1117VC LD1117FC (*) Available on request 2/28 OUTPUT VOLTAGE 1.2 V 1.2 V 1.8 V 1.8 V 2.5 V 2.5 V 2.85 V 3V 3V 3.3 V 3.3 V 5V 5V ADJ FROM 1.25 TO 15V ADJ FROM 1.25 TO 15V LD1117 SERIES Table 2: Absolute Maximum Ratings Symbol Parameter VIN DC Input Voltage Ptot Power Dissipation Tstg Storage Temperature Range Top Operating Junction Temperature Range for C Version for standard Version Value Unit 15 V 12 W -40 to +150 °C -40 to +125 0 to +125 °C °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. Over the above suggested Max Power Dissipation a Short Circuit could definitively damage the device. Table 3: Thermal Data Symbol Parameter Rthj-case Thermal Resistance Junction-case SOT-223 SO-8 DPAK 15 20 8 Rthj-amb Thermal Resistance Junction-ambient TO-220 TO-220FM Unit 3 4 °C/W 50 60 °C/W Figure 3: Application Circuit (FOR 1.2 V) Figure 4: Application Circuit (FOR OTHER FIXED OUTPUT VOLTAGES) 3/28 LD1117 SERIES Table 4: Electrical Characteristics Of LD1117#12 (refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF, R = 120 Ω between GND and OUT pins, unless otherwise specified) Symbol Parameter Test Conditions VO Output Voltage Vin = 3.2 V IO = 10 mA VO Reference Voltage IO = 10 to 800 mA Min. TJ = 25°C ∆VO Line Regulation Vin - VO= 1.4 to 10 V Vin - VO = 1.5 to 13.75 V IO = 10 mA ∆VO Load Regulation Vin - VO = 3 V ∆VO Temperature Stability ∆VO Long Term Stability Typ. Max. Unit 1.188 1.20 1.212 V 1.140 1.20 1.260 V 0.035 0.2 % 0.1 0.4 % IO = 10 to 800 mA 0.5 % 1000 hrs, TJ = 125°C 0.3 % Vin Operating Input Voltage 15 V Iadj Adjustment Pin Current Vin ≤ 15 V 60 120 µA ∆Iadj Adjustment Pin Current Change Vin - VO = 1.4 to 10 V IO = 10 to 800 mA 1 5 µA IO(min) Minimum Load Current Vin = 15 V 2 5 mA 950 1300 mA IO Output Current Vin - VO = 5 V TJ = 25°C eN Output Noise (%VO) Supply Voltage Rejection B =10Hz to 10KHz TJ = 25°C SVR Vd Dropout Voltage Thermal Regulation TJ = 25°C IO = 40 mA f = 120Hz Vin - VO = 3 V Vripple = 1 VPP 800 60 0.003 % 75 dB IO = 100 mA 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25°C 30ms Pulse 0.01 0.1 V %/W Table 5: Electrical Characteristics Of LD1117#18 (refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF unless otherwise specified) Symbol Parameter Test Conditions VO Output Voltage Vin = 3.8 V IO = 10 mA TJ = 25°C VO Output Voltage IO = 0 to 800 mA Vin = 3.3 to 8 V ∆VO Line Regulation Vin = 3.3 to 8 V IO = 0 mA ∆VO Load Regulation Vin = 3.3 V IO = 0 to 800 mA ∆VO Temperature Stability ∆VO Long Term Stability 1000 hrs, TJ = 125°C Operating Input Voltage IO = 100 mA Id Quiescent Current Vin ≤ 8 V Output Current Vin = 6.8 V TJ = 25°C eN Output Noise Voltage B =10Hz to 10KHz Supply Voltage Rejection IO = 40 mA f = 120Hz Vin = 5.5 V Vripple = 1 VPP IO = 100 mA Dropout Voltage Thermal Regulation 4/28 Max. Unit 1.78 1.8 1.82 V 1.76 1.84 V 1 6 mV 1 10 mV % 0.3 IO Vd Typ. 0.5 Vin SVR Min. 800 TJ = 25°C TJ = 25°C 60 % 10 V 5 10 mA 950 1300 mA 100 µV 75 dB 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25°C 30ms Pulse 0.01 0.1 V %/W LD1117 SERIES Table 6: Electrical Characteristics Of LD1117#25 (refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit 2.5 2.525 V 2.55 V VO Output Voltage Vin = 4.5 V IO = 10 mA TJ = 25°C 2.475 VO Output Voltage IO = 0 to 800 mA Vin = 3.9 to 10 V 2.45 ∆VO Line Regulation Vin = 3.9 to 10 V IO = 0 mA 1 6 mV ∆VO Load Regulation Vin = 3.9 V IO = 0 to 800 mA 1 10 mV ∆VO Temperature Stability ∆VO Long Term Stability Vin Operating Input Voltage 1000 hrs, TJ = 125°C IO = 100 mA Id Quiescent Current Vin ≤ 10 V IO Output Current Vin = 7.5 V TJ = 25°C eN Output Noise Voltage B =10Hz to 10KHz Supply Voltage Rejection IO = 40 mA f = 120Hz Vin = 5.5 V Vripple = 1 VPP IO = 100 mA SVR Vd Dropout Voltage Thermal Regulation 800 TJ = 25°C TJ = 25°C 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 µV 75 dB 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25°C 30ms Pulse 0.01 0.1 V %/W Table 7: Electrical Characteristics Of LD1117#28 (refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF unless otherwise specified) Symbol Parameter Test Conditions VO Output Voltage Vin = 4.85 VIO = 10 mA Min. Typ. Max. Unit TJ = 25°C 2.82 2.85 2.88 V 2.79 VO Output Voltage IO = 0 to 800 mA Vin = 4.25 to 10 V ∆VO Line Regulation Vin = 4.25 to 10 V IO = 0 mA ∆VO Load Regulation Vin = 4.25 V IO = 0 to 800 mA ∆VO Temperature Stability ∆VO 2.91 V 1 6 mV 1 10 mV 0.5 Long Term Stability 1000 hrs, TJ = 125°C Vin Operating Input Voltage IO = 100 mA % 0.3 % 15 V 5 10 mA 950 1300 mA Id Quiescent Current Vin ≤ 10 V IO Output Current Vin = 7.85 VTJ = 25°C eN Output Noise Voltage B =10Hz to 10KHz Supply Voltage Rejection IO = 40 mA f = 120Hz Vin = 5.85 VVripple = 1 VPP Dropout Voltage IO = 100 mA 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25°C 30ms Pulse 0.01 0.1 SVR Vd Thermal Regulation 800 TJ = 25°C TJ = 25°C 60 100 µV 75 dB V %/W 5/28 LD1117 SERIES Table 8: Electrical Characteristics Of LD1117#30 (refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF unless otherwise specified) Symbol Parameter Test Conditions IO = 10 mA Min. Typ. Max. Unit 3 3.03 V 3.06 V VO Output Voltage Vin = 5 V TJ = 25°C 2.97 VO Output Voltage IO = 0 to 800 mA Vin = 4.5 to 10 V 2.94 ∆VO Line Regulation Vin = 4.5 to 12 V IO = 0 mA 1 6 mV ∆VO Load Regulation Vin = 4.5 V IO = 0 to 800 mA 1 10 mV ∆VO Temperature Stability ∆VO Long Term Stability Vin Operating Input Voltage 1000 hrs, TJ = 125°C IO = 100 mA Id Quiescent Current Vin ≤ 12 V IO Output Current Vin = 8 V eN Output Noise Voltage B =10Hz to 10KHz Supply Voltage Rejection IO = 40 mA f = 120Hz Vin = 6 V Vripple = 1 VPP IO = 100 mA SVR Vd Dropout Voltage Thermal Regulation TJ = 25°C 800 TJ = 25°C TJ = 25°C 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 µV 75 dB 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25°C 30ms Pulse 0.01 0.1 V %/W Table 9: Electrical Characteristics Of LD1117#33 (refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit 3.3 3.333 V 3.365 V VO Output Voltage Vin = 5.3 V IO = 10 mA TJ = 25°C 3.267 VO Output Voltage IO = 0 to 800 mA Vin = 4.75 to 10 V 3.235 ∆VO Line Regulation Vin = 4.75 to 15 V IO = 0 mA 1 6 mV ∆VO Load Regulation Vin = 4.75 V IO = 0 to 800 mA 1 10 mV ∆VO Temperature Stability ∆VO Long Term Stability Vin Operating Input Voltage 1000 hrs, TJ = 125°C IO = 100 mA Id Quiescent Current Vin ≤ 15 V IO Output Current Vin = 8.3 V TJ = 25°C eN Output Noise Voltage B =10Hz to 10KHz Supply Voltage Rejection IO = 40 mA f = 120Hz Vin = 6.3 V Vripple = 1 VPP IO = 100 mA SVR Vd Dropout Voltage Thermal Regulation 6/28 800 TJ = 25°C TJ = 25°C 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 µV 75 dB 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25°C 30ms Pulse 0.01 0.1 V %/W LD1117 SERIES Table 10: Electrical Characteristics Of LD1117#50 (refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF unless otherwise specified) Symbol Parameter Test Conditions VO Output Voltage Vin = 7 V VO Output Voltage IO = 0 to 800 mA IO = 10 mA Vin = 6.5 to 15 V TJ = 25°C Min. Typ. Max. Unit 4.95 5 5.05 V 5.1 V 4.9 ∆VO Line Regulation Vin = 6.5 to 15 V IO = 0 mA 1 10 mV ∆VO Load Regulation Vin = 6.5 V IO = 0 to 800 mA 1 15 mV ∆VO Temperature Stability ∆VO Long Term Stability Vin Operating Input Voltage 1000 hrs, TJ = 125°C IO = 100 mA Id Quiescent Current Vin ≤ 15 V IO Output Current Vin = 10 V TJ = 25°C eN Output Noise Voltage B =10Hz to 10KHz Supply Voltage Rejection IO = 40 mA f = 120Hz Vin = 8 V Vripple = 1 VPP IO = 100 mA SVR Vd Dropout Voltage Thermal Regulation 800 TJ = 25°C TJ = 25°C 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 µV 75 dB 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25°C 30ms Pulse 0.01 0.1 V %/W Table 11: Electrical Characteristics Of LD1117 (ADJUSTABLE) (refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit 1.238 1.25 1.262 V 1.275 V 0.035 0.2 % 0.1 0.4 % Vref Reference Voltage Vref Reference Voltage ∆VO Line Regulation Vin - VO = 2 V IO = 10 mA TJ = 25°C IO = 10 to 800 mA Vin - VO= 1.4 to 10 V Vin - VO = 1.5 to 13.75 V IO = 10 mA ∆VO Load Regulation Vin - VO = 3 V ∆VO Temperature Stability ∆VO Long Term Stability 1.225 IO = 10 to 800 mA 0.5 % 1000 hrs, TJ = 125°C 0.3 % Vin Operating Input Voltage 15 V Iadj Adjustment Pin Current Vin ≤ 15 V 60 120 µA ∆Iadj Adjustment Pin Current Change Vin - VO = 1.4 to 10 V IO = 10 to 800 mA 1 5 µA IO(min) Minimum Load Current Vin = 15 V 2 5 mA 950 1300 mA IO Output Current Vin - VO = 5 V TJ = 25°C eN Output Noise (%VO) Supply Voltage Rejection B =10Hz to 10KHz TJ = 25°C SVR Vd Dropout Voltage Thermal Regulation TJ = 25°C IO = 40 mA f = 120Hz Vin - VO = 3 V Vripple = 1 VPP 800 60 0.003 % 75 dB IO = 100 mA 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25°C 30ms Pulse 0.01 0.1 V %/W 7/28 LD1117 SERIES Table 12: Electrical Characteristics Of LD1117#12C (refer to the test circuits, TJ = 0 to 125°C, CO = 10 µF, R = 120 Ω between GND and OUT pins, unless otherwise specified) Symbol Parameter Test Conditions Min. Vref Reference Voltage Vin - VO= 2V IO = 10 mA Vref Reference Voltage ∆VO Line Regulation IO = 10 to 800 mA Vin - VO= 1.4 to 10 V Vin - VO = 1.5 to 13.75 V IO = 10 mA Vin - VO = 3 V ∆VO Load Regulation ∆VO Temperature Stability ∆VO Long Term Stability Vin Operating Input Voltage TJ = 25°C Typ. Max. Unit 1.176 1.20 1.224 V 1.120 1.20 1.280 V 1 % IO = 10 to 800 mA 1 0.5 1000 hrs, TJ = 125°C % % 0.3 % 15 V Iadj Adjustment Pin Current Vin ≤ 15 V 60 120 µA ∆Iadj Adjustment Pin Current Change Vin - VO = 1.4 to 10 V IO = 10 to 800 mA 1 5 µA IO(min) 2 5 mA 950 1300 mA Minimum Load Current Vin = 15 V IO Output Current Vin - VO = 5 V TJ = 25°C eN Output Noise (%VO) B =10Hz to 10KHz TJ = 25°C Supply Voltage Rejection TJ = 25°C IO = 40 mA f = 120Hz Vin - VO = 3 V Vripple = 1 VPP Dropout Voltage IO = 100 mA TJ = 0 to 125°C 1 1.1 IO = 500 mA TJ = 0 to 125°C 1.05 1.2 IO = 800 mA TJ = 0 to 125°C SVR Vd Thermal Regulation 8/28 Ta = 25°C 30ms Pulse 800 60 0.003 % 75 dB 1.10 1.3 0.01 0.1 V %/W LD1117 SERIES Table 13: Electrical Characteristics Of LD1117#18C (refer to the test circuits, TJ = -40 to 125°C, CO = 10 µF unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit 1.8 1.84 V 1.87 V VO Output Voltage Vin = 3.8 V IO = 10 mA TJ = 25°C 1.76 VO Output Voltage IO = 0 to 800 mA Vin = 3.9 to 10 V 1.73 ∆VO Line Regulation Vin = 3.3 to 8 V IO = 0 mA 1 30 mV ∆VO Load Regulation Vin = 3.3 V IO = 0 to 800 mA 1 30 mV ∆VO Temperature Stability ∆VO Long Term Stability Vin Operating Input Voltage 1000 hrs, TJ = 125°C IO = 100 mA Id Quiescent Current Vin ≤ 8 V IO Output Current Vin = 6.8 V TJ = 25°C eN Output Noise Voltage B =10Hz to 10KHz Supply Voltage Rejection TJ = 25°C IO = 40 mA f = 120Hz Vin = 5.5 V Vripple = 1 VPP IO = 100 mA TJ = 0 to 125°C SVR Vd Vd Dropout Voltage Dropout Voltage Thermal Regulation 800 TJ = 25°C 60 0.5 % 0.3 % 10 V 5 10 mA 950 1300 mA 100 µV 75 dB 1 1.1 IO = 500 mA TJ = 0 to 125°C 1.05 1.15 IO = 800 mA TJ = 0 to 125°C 1.10 1.2 IO = 100 mA 1.1 IO = 500 mA 1.2 IO = 800 mA 1.3 Ta = 25°C 30ms Pulse 0.01 0.1 V V %/W 9/28 LD1117 SERIES Table 14: Electrical Characteristics Of LD1117#25C (refer to the test circuits, TJ = -40 to 125°C, CO = 10 µF unless otherwise specified) Symbol Parameter Test Conditions VO Output Voltage Vin = 4.5 V IO = 10 mA VO Output Voltage IO = 0 to 800 mA Vin = 3.9 to 10 V TJ = 25°C Min. Typ. Max. Unit 2.45 2.5 2.55 V 2.6 V 2.4 ∆VO Line Regulation Vin = 3.9 to 10 V IO = 0 mA 1 30 mV ∆VO Load Regulation Vin = 3.9 V IO = 0 to 800 mA 1 30 mV ∆VO Temperature Stability ∆VO Long Term Stability Vin Operating Input Voltage 1000 hrs, TJ = 125°C IO = 100 mA Id Quiescent Current Vin ≤ 10 V IO Output Current Vin = 7.5 V TJ = 25°C eN Output Noise Voltage B =10Hz to 10KHz Supply Voltage Rejection TJ = 25°C IO = 40 mA f = 120Hz Vin = 5.5 V Vripple = 1 VPP IO = 100 mA TJ = 0 to 125°C SVR Vd Vd Dropout Voltage Dropout Voltage Thermal Regulation 10/28 800 TJ = 25°C 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 µV 75 dB 1 1.1 IO = 500 mA TJ = 0 to 125°C 1.05 1.15 IO = 800 mA TJ = 0 to 125°C 1.10 1.2 IO = 100 mA 1.1 IO = 500 mA 1.2 IO = 800 mA 1.3 Ta = 25°C 30ms Pulse 0.01 0.1 V V %/W LD1117 SERIES Table 15: Electrical Characteristics Of LD1117#30C (refer to the test circuits, TJ = -40 to 125°C, CO = 10 µF unless otherwise specified) Symbol Parameter Test Conditions IO = 10 mA Min. Typ. Max. Unit 3 3.06 V 3.12 V VO Output Voltage Vin = 5 V TJ = 25°C 2.94 VO Output Voltage IO = 0 to 800 mA Vin = 4.5 to 10 V 2.88 ∆VO Line Regulation Vin = 4.5 to 12 V IO = 0 mA 1 30 mV ∆VO Load Regulation Vin = 4.5 V IO = 0 to 800 mA 1 30 mV ∆VO Temperature Stability ∆VO Long Term Stability Vin Operating Input Voltage 1000 hrs, TJ = 125°C IO = 100 mA Id Quiescent Current Vin ≤ 12 V IO Output Current Vin = 8 V eN Output Noise Voltage B =10Hz to 10KHz Supply Voltage Rejection TJ = 25°C IO = 40 mA f = 120Hz Vin = 6 V Vripple = 1 VPP IO = 100 mA TJ = 0 to 125°C SVR Vd Vd Dropout Voltage Dropout Voltage Thermal Regulation TJ = 25°C 800 TJ = 25°C 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 µV 75 dB 1 1.1 IO = 500 mA TJ = 0 to 125°C 1.05 1.15 IO = 800 mA TJ = 0 to 125°C 1.10 1.2 IO = 100 mA 1.1 IO = 500 mA 1.2 IO = 800 mA 1.3 Ta = 25°C 30ms Pulse 0.01 0.1 V V %/W 11/28 LD1117 SERIES Table 16: Electrical Characteristics Of LD1117#33C (refer to the test circuits, TJ = -40 to 125°C, CO = 10 µF unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit 3.3 3.36 V 3.44 V VO Output Voltage Vin = 5.3 V IO = 10 mA TJ = 25°C 3.24 VO Output Voltage IO = 0 to 800 mA Vin = 4.75 to 10 V 3.16 ∆VO Line Regulation Vin = 4.75 to 15 V IO = 0 mA 1 30 mV ∆VO Load Regulation Vin = 4.75 V IO = 0 to 800 mA 1 30 mV ∆VO Temperature Stability ∆VO Long Term Stability Vin Operating Input Voltage 1000 hrs, TJ = 125°C IO = 100 mA Id Quiescent Current Vin ≤ 15 V IO Output Current Vin = 8.3 V TJ = 25°C eN Output Noise Voltage B =10Hz to 10KHz Supply Voltage Rejection TJ = 25°C IO = 40 mA f = 120Hz Vin = 6.3 V Vripple = 1 VPP IO = 100 mA TJ = 0 to 125°C SVR Vd Vd Dropout Voltage Dropout Voltage Thermal Regulation 12/28 800 TJ = 25°C 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 µV 75 dB 1 1.1 IO = 500 mA TJ = 0 to 125°C 1.05 1.15 IO = 800 mA TJ = 0 to 125°C 1.10 1.2 IO = 100 mA 1.1 IO = 500 mA 1.2 IO = 800 mA 1.3 Ta = 25°C 30ms Pulse 0.01 0.1 V V %/W LD1117 SERIES Table 17: Electrical Characteristics Of LD1117#50C (refer to the test circuits, TJ = -40 to 125°C, CO = 10 µF unless otherwise specified) Symbol Parameter Test Conditions IO = 10 mA Min. Typ. Max. Unit 5 5.1 V 5.2 V VO Output Voltage Vin = 7 V TJ = 25°C 4.9 VO Output Voltage IO = 0 to 800 mA Vin = 6.5 to 15 V 4.8 ∆VO Line Regulation Vin = 6.5 to 15 V IO = 0 mA 1 50 mV ∆VO Load Regulation Vin = 6.5 V IO = 0 to 800 mA 1 50 mV ∆VO Temperature Stability ∆VO Long Term Stability Vin Operating Input Voltage 1000 hrs, TJ = 125°C IO = 100 mA Id Quiescent Current Vin ≤ 15 V IO Output Current Vin = 10 V TJ = 25°C eN Output Noise Voltage B =10Hz to 10KHz Supply Voltage Rejection TJ = 25°C IO = 40 mA f = 120Hz Vin = 8 V Vripple = 1 VPP IO = 100 mA TJ = 0 to 125°C SVR Vd Vd Dropout Voltage Dropout Voltage Thermal Regulation 800 TJ = 25°C 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 µV 75 dB 1 1.1 IO = 500 mA TJ = 0 to 125°C 1.05 1.15 IO = 800 mA TJ = 0 to 125°C 1.10 1.2 IO = 100 mA 1.1 IO = 500 mA 1.2 IO = 800 mA 1.3 Ta = 25°C 30ms Pulse 0.01 0.1 V V %/W 13/28 LD1117 SERIES Table 18: Electrical Characteristics Of LD1117C (ADJUSTABLE) (refer to the test circuits, TJ = -40 to 125°C, CO = 10 µF unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit 1.225 1.25 1.275 V 1.3 V 1 % Vref Reference Voltage Vref Reference Voltage ∆VO Line Regulation Vin - VO = 2 V IO = 10 mA TJ = 25°C IO = 10 to 800 mA Vin - VO= 1.4 to 10 V Vin - VO = 1.5 to 13.75 V IO = 10 mA Vin - VO = 3 V ∆VO Load Regulation ∆VO Temperature Stability ∆VO Long Term Stability Vin Operating Input Voltage 1.2 IO = 10 to 800 mA 1 0.5 1000 hrs, TJ = 125°C % % 0.3 % 15 V Iadj Adjustment Pin Current Vin ≤ 15 V 60 120 µA ∆Iadj Adjustment Pin Current Change Vin - VO = 1.4 to 10 V IO = 10 to 800 mA 1 10 µA IO(min) 2 5 mA 950 1300 mA Minimum Load Current Vin = 15 V IO Output Current Vin - VO = 5 V TJ = 25°C eN Output Noise (%VO) B =10Hz to 10KHz TJ = 25°C Supply Voltage Rejection TJ = 25°C IO = 40 mA f = 120Hz Vin - VO = 3 V Vripple = 1 VPP Dropout Voltage IO = 100 mA TJ = 0 to 125°C 1 1.1 IO = 500 mA TJ = 0 to 125°C 1.05 1.15 IO = 800 mA TJ = 0 to 125°C 1.10 SVR Vd Vd Dropout Voltage 800 60 0.003 % 75 dB TYPICAL APPLICATIONS Figure 5: Negative Supply 14/28 1.2 IO = 100 mA 1.1 IO = 500 mA 1.2 IO = 800 mA Thermal Regulation Ta = 25°C 30ms Pulse V V 1.3 0.01 0.1 %/W LD1117 SERIES Figure 6: Active Terminator for SCSI-2 BUS Figure 7: Circuit for Increasing Output Voltage Figure 8: Voltage Regulator With Reference 15/28 LD1117 SERIES Figure 9: Battery Backed-up Regulated Supply 16/28 LD1117 SERIES Figure 10: Post-Regulated Dual Supply LD1117 ADJUSTABLE: APPLICATION NOTE The LD1117 ADJUSTABLE has a thermal stabilized 1.25±0.012V reference voltage between the OUT and ADJ pins. IADJ is 60µA typ. (120µA max.) and ∆IADJ is 1µA typ. (5µA max.). R1 is normally fixed to 120Ω. From figure 7 we obtain: VOUT = VREF + R2 (IADJ +IR1) = VREF + R2 (IADJ +VREF /R1) = VREF (1 + R2 / R1) + R2 x IADJ. In normal application R2 value is in the range of few kohm, so the R2 x IDJ product could not be considered in the VOUT calculation; then the above expression becomes: VOUT = VREF (1 + R2 / R1). In order to have the better load regulation it is important to realize a good Kelvin connection of R1 and R2 resistors. In particular R1 connection must be realized very close to OUT and ADJ pin, while R2 ground connection must be placed as near as possible to the negative Load pin. Ripple rejection can be improved by introducing a 10µF electrolytic capacitor placed in parallel to the R2 resistor (see Fig.8). 17/28 LD1117 SERIES Figure 11: Adjustable Output Voltage Application Figure 12: Adjustable Output Voltage Application with improved Ripple Rejection 18/28 LD1117 SERIES SOT-223 MECHANICAL DATA mm. mils DIM. MIN. TYP A MAX. MIN. TYP. 1.8 A1 0.02 B 0.6 B1 MAX. 70.9 0.1 0.8 3.9 0.7 0.85 23.6 27.6 33.5 2.9 3 3.15 114.2 118.1 124.0 c 0.24 0.26 0.35 9.4 10.2 13.8 D 6.3 6.5 6.7 248.0 255.9 263.8 e 2.3 90.6 e1 4.6 181.1 E 3.3 3.5 3.7 129.9 137.8 145.7 H 6.7 7 7.3 129.9 137.8 145.7 V 10˚ 10˚ 0046067/H 19/28 LD1117 SERIES SO-8 MECHANICAL DATA DIM. mm. MIN. TYP inch MAX. MIN. TYP. MAX. A 1.35 1.75 0.053 0.069 A1 0.10 0.25 0.04 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 E 3.80 4.00 0.150 0.157 e 1.27 0.050 H 5.80 6.20 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 k ddd 8˚ (max.) 0.1 0.04 0016023/C 20/28 LD1117 SERIES DPAK MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 2.2 2.4 0.086 0.094 A1 0.9 1.1 0.035 0.043 A2 0.03 0.23 0.001 0.009 B 0.64 0.9 0.025 0.035 B2 5.2 5.4 0.204 0.212 C 0.45 0.6 0.017 0.023 C2 0.48 0.6 0.019 0.023 D 6 6.2 0.236 D1 E 5.1 6.4 E1 6.6 0.252 4.7 e 0.244 0.200 0.260 0.185 2.28 0.090 e1 4.4 4.6 0.173 0.181 H 9.35 10.1 0.368 0.397 L 1 (L1) L2 L4 0.039 2.8 0.110 0.8 0.6 0.031 1 0.023 0.039 0068772-F 21/28 LD1117 SERIES TO-220 MECHANICAL DATA DIM. mm. MIN. MAX. MIN. A 4.40 4.60 0.173 0.181 C 1.23 1.32 0.048 0.051 D 2.40 2.72 0.094 0.107 D1 TYP inch 1.27 TYP. MAX. 0.050 E 0.49 0.70 0.019 0.027 F 0.61 0.88 0.024 0.034 F1 1.14 1.70 0.044 0.067 F2 1.14 1.70 0.044 0.067 G 4.95 5.15 0.194 0.203 G1 2.4 2.7 0.094 0.106 H2 10.0 10.40 0.393 L2 16.4 0.409 0.645 L4 13.0 14.0 0.511 0.551 L5 2.65 2.95 0.104 0.116 L6 15.25 15.75 0.600 0.620 L7 6.2 6.6 0.244 0.260 L9 3.5 3.93 0.137 0.154 DIA. 3.75 3.85 0.147 0.151 P011C 22/28 LD1117 SERIES TO-220FM MECHANICAL DATA DIM. mm. MIN. TYP inch MAX. MIN. TYP. MAX. A 4.50 4.90 0.177 0.193 B 2.34 2.74 0.092 0.108 D 2.56 2.96 0.101 0.117 E 0.45 0.60 0.018 F 0.70 0.90 0.028 0.50 F1 0.020 0.035 1.47 G 0.058 5.08 G1 2.34 H 9.96 L2 2.54 0.024 0.200 2.74 0.092 10.36 0.392 15.8 0.100 0.108 0.408 0.622 L4 9.45 10.05 0.372 0.396 L6 15.67 16.07 0.617 0.633 L7 8.99 9.39 0.354 0.370 L8 DIA. 3.30 3.08 0.130 3.28 0.121 0.129 7012510C-H 23/28 LD1117 SERIES Tape & Reel SOT223 MECHANICAL DATA mm. inch DIM. MIN. TYP A MIN. TYP. 330 13.0 13.2 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 24/28 MAX. 0.504 0.512 14.4 0.519 0.567 Ao 6.73 6.83 6.93 0.265 0.269 0.273 Bo 7.32 7.42 7.52 0.288 0.292 0.296 Ko 1.78 2 0.070 Po 3.9 4.0 4.1 0.153 0.157 0.161 P 7.9 8.0 8.1 0.311 0.315 0.319 0.078 LD1117 SERIES Tape & Reel SO-8 MECHANICAL DATA mm. inch DIM. MIN. A TYP MAX. MIN. 330 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 TYP. 0.504 22.4 0.519 0.882 Ao 8.1 8.5 0.319 0.335 Bo 5.5 5.9 0.216 0.232 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 25/28 LD1117 SERIES Tape & Reel DPAK-PPAK MECHANICAL DATA mm. inch DIM. MIN. TYP A MIN. TYP. 330 13.0 13.2 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 26/28 MAX. 0.504 0.512 22.4 0.519 0.882 Ao 6.80 6.90 7.00 0.268 0.272 0.2.76 Bo 10.40 10.50 10.60 0.409 0.413 0.417 Ko 2.55 2.65 2.75 0.100 0.104 0.105 Po 3.9 4.0 4.1 0.153 0.157 0.161 P 7.9 8.0 8.1 0.311 0.315 0.319 LD1117 SERIES Table 19: Revision History Date Revision 22-Sep-2004 15.0 25-Oct-2004 16.0 Description of Changes Add new Part Number #12C; Typing Error: Note on table 2. Add Vref Reference Voltage on Table 12. 27/28 LD1117 SERIES Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 28/28