MPD LF202ED Low cost, 2w smt dual output dc/dc converter Datasheet

LF200ED Series
Low Cost, 2W SMT
Dual Output
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
• 2W Output Power
• Ultra-Miniature SMT Case
• 1,000 VDC Isolation
• -40ºC to +85ºC Operation
• Dual Output
• Low 0.24” Profile
Input
Parameter
Input Voltage Range
Min.
Typ.
Max.
5 VDC Input
4.5
5.0
5.5
12 VDC Input
10.8
12.0
13.2
Reverse Polarity Input Current
Input Filter
Units
VDC
1.0
A
Max.
Units
±1.2
%
Capacitor
Output
Parameter
• >3.5 MHour MTBF
Output Voltage Accuracy
• Industry Standard Pin-Out
Line Regulation
• LOWEST COST!
Conditions
Load Regulation
Conditions
Min.
Typ.
±3.0
For Vin Change of 1%
For Iout = 10% to 100%
%
±7
±15
%
Output Ripple (20 MHz)
75
150
mV P - P
Output Noise (20 MHz)
150
Temperature Coefficient
Output Short Circuit
250
mV P - P
±0.03
%/ºC
Max.
Units
Momentary (0.5 Sec.)
General
Parameter
Conditions
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Min.
Typ.
60 Seconds
1,000
VDC
500 VDC
1,000
MΩ
100 kHz, 1V
Switching Frequency
70
pF
70
kHz
Environmental
Parameter
Conditions
Operating Temperature Range
Ambient
Storage Temperature Range
Humidity
292 Page Street
Suite D
Stoughton, MA 02072
USA
Typ.
Max.
Units
-40
+25
+85
ºC
+125
ºC
95
%
-55
Cooling
MicroPower Direct Physical
Min.
Free Air Convection
RH, Non-condensing
Case Size
0.70 x 0.72 x 0.24 Inches (17.78 x 18.03 x 6.0 mm)
Case Material
Non-Conductive Black Plastic (UL94-V0)
Weight
T: (781) 344-8226
Reliability Specifications
F: (781) 344-8481
Parameter
E: [email protected]
MTBF
W: www.micropowerdirect.com
0.05 Oz (1.5g)
Conditions
Min.
MIL HDBK 217F, 25ºC, Gnd Benign
3.5
Conditions
Min.
Typ.
Max.
Units
MHours
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
Typ.
Max.
5 VDC Input
-0.7
7.0
12 VDC Input
-0.7
15.0
1.5 mm From Case For 10 Sec
All Models
Units
VDC
260.0
ºC
450
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Input
Model
Number
LF201ED
LF202ED
LF203ED
LF211ED
LF212ED
LF213ED
LF214ED
Voltage (VDC)
Nominal
5
5
5
12
12
12
12
Range
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
Output
Current (mA)
Full-Load
244
241
238
100
99
99
98
No-Load
30
30
30
15
15
15
15
Voltage
(VDC)
±5.0
±9.0
±12.0
±5.0
±9.0
±12.0
±15.0
Input
Capacitor
5 VDC
12 VDC
4.7 µF
2.2 µF
Vout
Output
Capacitor
5 VDC
9 VDC
12 VDC
15 VDC
4.7 µF
2.2 µF
1.0 µF
0.47 µF
For applications requiring very low output noise
levels, a simple LC filter should be effective.
5. It is recommended that a fuse be used on the
input of a power supply for protection. See the
Model Selection table above for the correct rating.
Mechanical Dimensions
Current
(mA, Min)
±200.0
±111.0
±83.0
±200.0
±111.0
±83.0
±67.0
Notes:
1. Output load regulation is specified for a load change of 10% to 100%.
2. When measuring output ripple, it is recommended that an external 0.33 µF ceramic
capacitor be placed from each output to common.
3. During operation, care must be taken not to exceed the specified input range of the
unit or to allow the output load to drop below the specified minimum (10% of full
load). Operating the unit under either of these conditions could cause damage to the
unit.
4. These converters are specified for operation without external components. However,
in some applications the addition of input/output capacitors will enhance stability and
reduce output ripple. Recommended capacitor values are:
Vin
Current
(mA, Max)
±20.0
±11.0
±8.0
±20.0
±11.0
±8.0
±7.0
1
2
3
5
6
7
Description
Pin
Fuse Rating
Slow-Blow
(mA)
82
83
84
83
84
84
85
500
500
500
200
200
200
200
Derating Curve
Recommended Solder Profile
Pin Connections
Pin
Efficiency
(%, Typ)
Description
-Vin
8
NC
+Vin
9
NC
NC
10
-Vout
-Vout
12
NC
Common
13
NC
+Vout
14
NC
NC = No Connection
Board Layout
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation on the unit
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]
Similar pages