MPD LF237RW Miniature smt, 2w wide input range dc/dc converter Datasheet

LF200RW Series
Miniature SMT, 2W
Wide Input Range
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
Input
• 2W Output Power
• 2:1 Input Voltage Range
• 1,500 VDC Isolation
• Short Circuit Protected
• Miniature SMT Package
• Single & Dual Outputs
• 1.0 MH MTBF
• Industry Standard Pin-Out
Parameter
RoHS Compliant
Input Start Voltage
Conditions
5 VDC Input
12 VDC Input
24 VDC Input
48 VDC Input
Input Filter
Reverse Polarity Input Current
Short Circuit Input Power
Min.
3.5
4.5
8.0
16.0
π (Pi) Filter
Typ.
4.0
7.0
12.0
24.0
Max.
4.5
9.0
18.0
36.0
Units
1.0
1,500
A
mW
Typ.
±1.0
±1.0
±0.3
±0.5
30
Max.
±2.0
±2.0
±0.5
±0.75
50
75
15
100
±3.0
±0.01
300
±5.0
±0.02
Units
%
%
%
%
mV P - P
mV P - P
mV rms
%
µSec
%
%/°C
Typ.
Max.
250
300
420
VDC
Output
Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Load Regulation
Ripple & Noise (20 MHz) (Note 1)
Ripple & Noise (20 MHz)
Ripple & Noise (20 MHz)
Output Power Protection
Transient Response Time (Note 2)
Transient Response Deviation
Temperature Coefficient
Output Short Circuit
Conditions
Min.
Vin = Min to Max
Iout = 25% to 100%
Over Line, Load & Temp.
120
50% Load Step Change
Continuous
General
Parameter
Isolation Voltage
Isolation Test Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
Conditions
60 Seconds
Flash Tested For 1 Sec
1,000 VDC
100 kHz, 1V
Min.
1,500
1,650
1,000
Units
VDC
VDC
MΩ
pF
kHz
Environmental
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Conditions
Ambient
Case
Min.
Typ.
-40
+25
-40
+25
-40
Free Air Convection
RH, Non-condensing
Max.
+65
+90
+125
Units
°C
°C
°C
95
%
Physical
Case Size
Case Material
Weight
0.94 x 0.54 x 0.30 Inches (23.8 x 13.7 x 7.62 mm)
Non-Conductive Black Plastic (UL94-V0)
0.18 Oz (5.1g)
Reliability Specifications
Parameter
MTBF
Conditions
MIL HDBK 217F, 25°C, Gnd Benign
Min.
1,000
Typ.
Max.
Units
kHours
Conditions
Min.
-0.7
-0.7
-0.7
-0.7
Typ.
Max.
11.0
25.0
50.0
100.0
260
1,800
Units
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
5 VDC Input
12 VDC Input
24 VDC Input
48 VDC Input
1.5 mm From Case For 10 Sec
All Models
VDC
°C
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Model
Number
LF201RW
LF202RW
LF203RW
LF204RW
LF205RW
LF206RW
LF207RW
LF211RW
LF212RW
LF213RW
LF214RW
LF215RW
LF216RW
LF217RW
LF221RW
LF222RW
LF223RW
LF224RW
LF225RW
LF226RW
LF227RW
LF231RW
LF232RW
LF233RW
LF234RW
LF235RW
LF236RW
LF237RW
Input
Output
Reflected
Efficiency
Voltage (VDC)
Current (mA)
Ripple
Voltage Current
Current
(%, Typ)
Nominal
Range
Full-Load No-Load (VDC) (mA, Max) (mA, Min) Current (mA)
5
4.5 - 9.0
471
40
3.3
500.0
125.0
100
70
5
4.5 - 9.0
548
40
5.0
400.0
100.0
100
73
5
4.5 - 9.0
534
40
12.0
167.0
42.0
100
75
5
4.5 - 9.0
582
40
15.0
134.0
33.0
100
73
5
4.5 - 9.0
667
40
±5.0
±200.0
±50.0
100
64
5
4.5 - 9.0
615
40
±12.0
±83.0
±21.0
100
69
5
4.5 - 9.0
598
40
±15.0
±67.0
±17.0
100
71
12
9.0 - 18.0
184
20
3.3
500.0
125.0
25
73
12
9.0 - 18.0
217
20
5.0
400.0
100.0
25
77
12
9.0 - 18.0
209
20
12.0
167.0
42.0
25
80
12
9.0 - 18.0
220
20
15.0
134.0
33.0
25
80
12
9.0 - 18.0
242
20
±5.0
±200.0
±50.0
25
73
12
9.0 - 18.0
224
20
±12.0
±83.0
±21.0
25
78
12
9.0 - 18.0
226
20
±15.0
±67.0
±17.0
25
78
24
18.0 - 36.0
96
10
3.3
500.0
125.0
15
72
24
18.0 - 36.0
109
10
5.0
400.0
100.0
15
77
24
18.0 - 36.0
109
10
12.0
167.0
42.0
15
80
24
18.0 - 36.0
108
10
15.0
134.0
33.0
15
81
24
18.0 - 36.0
119
10
±5.0
±200.0
±50.0
15
74
24
18.0 - 36.0
112
10
±12.0
±83.0
±21.0
15
78
24
18.0 - 36.0
110
10
±15.0
±67.0
±17.0
15
80
48
36.0 - 72.0
49
8
3.3
500.0
125.0
10
71
48
36.0 - 72.0
57
8
5.0
400.0
100.0
10
73
48
36.0 - 72.0
53
8
12.0
167.0
42.0
10
79
48
36.0 - 72.0
55
8
15.0
134.0
33.0
10
79
48
36.0 - 72.0
62
8
±5.0
±200.0
±50.0
10
71
48
36.0 - 72.0
57
8
±12.0
±83.0
±21.0
10
77
48
36.0 - 72.0
57
8
±15.0
±67.0
±17.0
10
77
Fuse Rating
Slow-Blow
(mA)
1,000
1,000
1,000
1,000
1,000
1,000
1,000
500
500
500
500
500
500
500
250
250
250
250
250
250
250
120
120
120
120
120
120
120
Notes:
1. When measuring output ripple, it is recommended that an external 0.47 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and
from each output to common for dual output units. For noise sensitive applications, the use of 3.3 µF capacitors will reduce the output ripple.
2. Transient recovery is measured to within a 1% error band for a load step change of 75% to 100%.
3. Operation at no-load will not damage these units. However, they may not meet all specifications.
4. Dual output units may be connected to provide a 10 VDC, 24 VDC or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs
and float the output common.
5. The converter should be connected to a low ac-impedance source. An input source with a highly inductive impedance may affect the stability of the converter. In applications where the converter output loading is high and input power is supplied over long lines, it may be necessary to use a capacitor on the input to insure start-up.
In this case, it is recommended that a low ESR (ESR <1.0Ω at 100 kHz) capacitor be mounted close to the converter. For 5V input units a 8.2 µF is recommended, for 12V
input units, a 3.3 µF; and for 24V & 48V units a 1.5 µF.
6. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating.
Derating Curve
Capacitive Load
Output (VDC)
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
Mechanical Dimensions
µF Max
2,200
1,000
170
110
470
100
47
Note: For dual output Units, Cap
load is given for each output.
Solder Layout
Pin Connections
Pin
Single
Dual
1
-Vin
-Vin
7
NC
NC
8
NC
Common
9
+Vout
+Vout
10
-Vout
-Vout
16
+Vin
+Vin
NC = No Connection
MicroPower Direct
Mechanical Notes:
Mechanica
• All dimen
dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]
Similar pages