STMicroelectronics LM2902YPT Low power quad operational amplifier Datasheet

LM193, LM193A, LM293,
LM293A, LM393, LM393A
Low Power Dual Voltage Comparators
■
Wide single-supply voltage range or dual
supplies: +2V to +36V or ±1V to ±18V
■
Very low supply current (0.4mA) independent
of supply voltage (1mW/comparator at +5V)
■
Low input bias current: 25nA typ.
■
Low input offset current: ±5nA typ.
■
Low input offset voltage: ±1mV typ.
■
Input common-mode voltage range includes
ground
■
Low output saturation voltage: 250mV typ. (Io =
4mA)
■
Differential input voltage range equal to the
supply voltage
■
TTL, DTL, ECL, MOS, CMOS compatible
outputs
N
DIP8
(Plastic Package)
D
SO-8
(Plastic Micropackage)
P
TSSOP8
(Thin Shrink Small Outline Package)
S
Mini SO-8
(Plastic Micropackage)
Description
Pin connections (top view)
These devices consist of two independent low
voltage comparators designed specifically to
operate from a single supply over a wide range of
voltages. Operation from split power supplies is
also possible.
1
These comparators also have a unique
characteristic in that the input common-mode
voltage range includes ground even though
operated from a single power supply voltage.
February 2006
2
-
3
+
4
Rev. 6
8
7
-
6
+
5
1 - Output 1
2 - Inverting input 1
3 - Non-inverting input 1
4 - VCC5 - Non-inverting input 2
6 - Inverting input 2
7 - Output 2
8 - VCC+
1/15
www.st.com
15
Order Codes
1
LM193, LM193A, LM293, LM293A, LM393, LM393A
Order Codes
Part Number
Temperature
Range
Package
Packing
SO-8
Tube or Tape & Reel
DIP8
Tube
LM193D/LM193DT
SO-8
Tube or Tape & Reel
LM193N
DIP8
Tube
LM293AD/LM293ADT
SO-8
Tube or Tape & Reel
LM293AN
DIP8
Tube
LM293D/LM293DT
SO-8
Tube or Tape & Reel
DIP8
Tube
LM293PT
TSSOP8
(Thin Shrink Outline
Package)
Tape & Reel
LM293ST
Mini SO-8
Tape & Reel
LM393AD/LM393ADT
SO-8
Tube or Tape & Reel
LM393D/LM393DT
SO-8
Tube or Tape & Reel
DIP8
Tube
LM393PT
TSSOP8
(Thin Shrink Outline
Package)
Tape & Reel
LM393ST
Mini SO-8
Tape & Reel
SO-8 (automotive
grade level)
Tube or Tape & Reel
LM193AD/LM193ADT
LM193AN
-55°C, +125°C
LM293N
-40°C, +105°C
LM393N
0°C, +70°C
LM393YDT/YD
2/15
-40°C, +125°C
Marking
LM193, LM193A, LM293, LM293A, LM393, LM393A
2
Schematic Diagram (1/2 LM193)
Schematic Diagram (1/2 LM193)
VCC
3.5µA
100µA
3.5µA
100µA
Non-inverting
Input
VCC
VCC
VO
Inverting
Input
VCC
3/15
Absolute Maximum Ratings
3
LM193, LM193A, LM293, LM293A, LM393, LM393A
Absolute Maximum Ratings
Table 1.
Key parameters and their absolute maximum ratings
Symbol
Parameter
VCC
Supply Voltage
Vid
Differential Input Voltage
Vi
Input Voltage
Output Short-circuit to Ground - note (1)
Value
Unit
±18 or 36
V
±36
V
-0.3 to +36
V
Infinite
(2)
Pd
Power Dissipation
DIP-8
SO-8
TSSOP8
Mini SO-8
Tstg
Storage Temperature Range
1250
710
625
580
-65 to +150
mW
°C
+
1. Short-circuits from the output to VCC can cause excessive heating and eventual destruction. The
maximum output current is approximately 20mA independent of the magnitude of V CC +.
2. Pd is calculated with Tamb = +25°C, Tj = +150°C and
Rthja = 100°C/W for DIP8 package
Rthja = 175°C/W for SO-8 package
Rthja = 200°C/W for TSSOP8 package
Rthja = 215°C/W for Mini SO-8 package
Table 2.
Symbol
4/15
Operating conditions
Parameter
Vicm
Common Mode Input Voltage Range
Toper
Operating Free-Air Temperature range
LM193, A
LM293, A
LM393, A
Value
Unit
0 to VCC + -1.5
V
-55 to +125
-40 to +105
0 to +70
°C
LM193, LM193A, LM293, LM293A, LM393, LM393A
Electrical Characteristics
4
Electrical Characteristics
Table 3.
VCC+ = +5V, VCC-= 0V, Tamb = +25°C (unless otherwise specified)
Symbol
Parameter
LM193A - LM293A
LM393A
Min.
Typ.
Max.
LM193- LM293
LM393
Min
Typ.
Max.
Unit
Vio
Input Offset Voltage - note (1)
Tamb = +25°C
Tmin ≤ T amb ≤ T max
1
2
4
1
5
9
mV
Iio
Input Offset Current
Tamb = +25°C
Tmin ≤ T amb ≤ T max
3
25
100
5
50
150
nA
Iib
Input Bias Current (I+ or I-) - note (2)
Tamb = +25°C
Tmin ≤ T amb ≤ T max
25
100
300
25
250
400
nA
Avd
Large Signal Voltage Gain
VCC = 15V, RL = 15kΩ, Vo = 1V to 11V
ICC
Supply Current (all comparators)
VCC = +5V, no load
VCC = +30V, no load
Vicm
Input Common Mode Voltage Range - note (3)
VCC = 30V
Tamb = +25°C
Tmin ≤ T amb ≤ T max
Vid
Differential Input Voltage -note (4)
VOL
Low Level Output Voltage
Vid = -1V, Isink = 4mA
Tamb = +25°C
Tmin ≤ T amb ≤ T max
IOH
High Level Output Current (Vid = 1V)
VCC = Vo = 30V
Tamb = +25°C
Tmin ≤ T amb ≤ T max
ISINK
Output Sink Current
Vid = 1V, Vo = 1.5V
50
200
0.4
1
50
1
2.5
VCC+ -1.5
VCC+ -2
0
0
0.4
1
0
0
VCC+
250
400
700
250
mA
VCC+ -1.5
VCC+ -2
V
400
700
0.1
1
16
1
2.5
VCC+
0.1
6
V/mV
200
1
6
16
tre
Response Time - note (5)
RL= 5.1kΩ connected to VCC+
1.3
1.3
trel
Large Signal Response Time
RL= 5.1kΩ connected to VCC+, el = TTL,
V(ref) = +1.4v
300
300
mV
nA
µA
mA
µs
ns
1. At output switch point, Vo ≈ 1.4V, Rs = 0 with VCC+ from 5V to 30V, and over the full common-mode range (0V to VCC + 1.5V).
2. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant,
independent of the state of the output, so no loading charge exists on the reference of input lines.
3. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The
upper end of the common-mode voltage range is VCC+ -1.5V, but either or both inputs can go to +30V without damage.
4. The response time specified is for a 100mV input step with 5mV overdrive. For larger overdrive signals 300ns can be
obtained.
5. Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the
common-mode range, the comparator will provide a proper output state. The low input voltage state must not be less than 0.3V (or 0.3V bellow the negative power supply, if used).
5/15
Electrical Characteristics
Figure 1.
LM193, LM193A, LM293, LM293A, LM393, LM393A
Supply current vs. supply voltage
Figure 2.
80
0.8
Tamb= +25°C
0.6
Tamb = +70°C
0.4
Tamb = +125°C
0.2
R =
10
20
30
SUPPLY VOLTAGE (V)
Output saturation voltage vs.
frequency
0
-1
Tamb = -55°C
10
-2
10
-3
Tamb= +25°C
-2
10
-1
10
0
10
1
10
OUTPUT SINK CURRENT (mA)
Figure 5.
6
1 5
4
3
2
1
0
00
50
0
OUTPUT VOLTAGE (V)
Tamb= +25°C
40
20
Tamb = +125°C
Tamb = +70°C
0
10
20
30
SUPPLY VOLTAGE (V)
40
Response time for various input
overdrives - negative transition
1
10
INPUT VOLTAGE (mV)
Tamb = -55°C
i
Figure 4.
Tamb = +125°C
10
R = 10 9 Ω
Tamb = 0°C
40
Out of saturation
10
60
Response time for various input
overdrives - positive transition
Input overdrive : 100mV
5mV
20mV
5V
5.1kΩ
eI
eo
Tamb = +25°C
0
0.5
1
1.5
TIME (µs)
2
2
OUTPUT VOLTAGE (V)
SATURATION VOLTAGE (V)
Figure 3.
INPUT CURRENT (nA)
Tamb = 0°C
0
6/15
Vi = 0V
Tamb = -55°C
INPUT VOLTAGE (mV)
SUPPLY CURRENT (mA)
1
10
Input current vs. supply voltage
6
5
4
3
2
1
0
0
-50
-100
Input overdrive : 5mV
5V
5.1kΩ
20mV
eI
eo
100mV
Tamb= +25°C
0
0.5
1
1.5
TIME (µs)
2
LM193, LM193A, LM293, LM293A, LM393, LM393A
4.1
Typical applications
Figure 6.
Basic comparator
Electrical Characteristics
Figure 7.
Driving TTL
5V
VCC = 5V
15kΩ
10kW
+V(ref)
+V(ref)
1/2
LM193
VO
-V(ref)
Figure 8.
Low frequency op-amp
1/2
LM193
&
-V(ref)
Figure 9.
&
Driving CMOS
5V
(e o = 0V for e I = 0V)
5V
15k W
1/2
LM193
~
eI
100kW
2N 2222
0.5mF
+V(ref)
1/2
LM193
100kW
eo
1kW
&
-V(ref)
A V = 100
Figure 10. Low frequency op-amp
Figure 11. Transducer amplifier
5V
5V
15kW
Magnetic pick-up
1/2
LM193
~
eI
100kW
A V = 100
3kW
1/2
LM193
eo
1kW
10kW
eo
20MW
0.5mF
10kW
7/15
Electrical Characteristics
LM193, LM193A, LM293, LM293A, LM393, LM393A
Figure 12. Low frequency op-amp with offset
adjust
Figure 13. Zero crossing detector
(single power supply)
5V
Offset Adjust
5V
100kW
5V
1MW
R2
Rs
eI
100kW
1MW
RI
5.1kW
15kW
5.1kW
eI
1/2
LM193
~
100kW
5.1kW
2N 2222
1/2
LM193
1N4148
0.5mF
R1
100kW
20MW
1kW
10kW
eo
Figure 14. Limit comparator
Figure 15. Crystal controlled oscillator
VCC (12V)
2R S
VCC = 15V
200kW
10kW
2kW
100kW
V(ref)
1/2
LM193
high
Lamp
RS
eI
VCC
0
1/2
LM193
0.1mF
eo
~
2R S
1/2
LM193
f = 100kHz
2N 2222
200kW
V(ref)
low
Figure 16. Split-supply applications - zero
crossing detector
Figure 17. Comparator with a negative
reference
15V
15V
5.1k W
5.1kW
1/2
LM193
eI
1/2
LM193
eo
eI
~
~
5V
15V
8/15
15V
eo
LM193, LM193A, LM293, LM293A, LM393, LM393A
Electrical Characteristics
Figure 18. Two-decade high-frequency VCO
VCC
100kW
500pF
3kW
5.1kW
1/2
LM193
Frequency control
voltage input
vcontrol
0.01m F
0.1mF
VCC
3kW
1/2
LM193
Output 1
VCC /2
20kW
50kW
100kW
Output 2
20k W
1/2
LM193
VCC /2
VCC = +30V
+250mV Vcontrol +50V
700 Hz
fo 100kHz
9/15
Package Mechanical Data
5
LM193, LM193A, LM293, LM293A, LM393, LM393A
Package Mechanical Data
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a Lead-free second level interconnect. The category of
second level interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at: www.st.com.
5.1
DIP8 package
Plastic DIP-8 MECHANICAL DATA
mm.
inch
DIM.
MIN.
A
TYP
MAX.
MIN.
3.3
0.7
B
1.39
1.65
0.055
B1
0.91
1.04
0.036
b1
0.028
0.5
0.38
0.065
0.041
0.020
0.5
D
0.015
0.020
9.8
0.386
E
8.8
0.346
e
2.54
0.100
e3
7.62
0.300
e4
7.62
0.300
F
7.1
I
4.8
L
Z
0.280
0.189
3.3
0.44
MAX.
0.130
a1
b
TYP.
0.130
1.6
0.017
0.063
P001F
10/15
LM193, LM193A, LM293, LM293A, LM393, LM393A
5.2
Package Mechanical Data
SO8 package
SO-8 MECHANICAL DATA
DIM.
mm.
MIN.
TYP
inch
MAX.
MIN.
TYP.
0.053
0.069
MAX.
A
1.35
1.75
A1
0.10
0.25
0.04
0.010
A2
1.10
1.65
0.043
0.065
B
0.33
0.51
0.013
0.020
C
0.19
0.25
0.007
0.010
D
4.80
5.00
0.189
0.197
E
3.80
4.00
0.150
e
1.27
0.157
0.050
H
5.80
6.20
0.228
0.244
h
0.25
0.50
0.010
0.020
L
0.40
1.27
0.016
0.050
k
ddd
8˚ (max.)
0.1
0.04
0016023/C
11/15
Package Mechanical Data
5.3
LM193, LM193A, LM293, LM293A, LM393, LM393A
TSSOP8 package
TSSOP8 MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
A
MAX.
MIN.
TYP.
1.2
A1
0.05
A2
0.80
b
0.19
1.00
MAX.
0.047
0.15
0.002
1.05
0.031
0.30
0.007
0.006
0.039
0.041
0.012
c
0.09
0.20
0.004
D
2.90
3.00
3.10
0.114
0.118
0.122
E
6.20
6.40
6.60
0.244
0.252
0.260
E1
4.30
4.40
4.50
0.169
0.173
0.177
e
0.65
K
0˚
L
0.45
L1
0.60
1
0.008
0.0256
8˚
0˚
0.75
0.018
8˚
0.024
0.030
0.039
0079397/D
12/15
LM193, LM193A, LM293, LM293A, LM393, LM393A
5.4
Package Mechanical Data
MiniSO8 package
13/15
Revision History
6
LM193, LM193A, LM293, LM293A, LM393, LM393A
Revision History
Table 4.
14/15
Document revision history
Date
Revision
Changes
July 2002
1
First Release
Jan. 2005
2
Class A of the product included in the datasheet.
May 2005
3
PPAP references inserted in the datasheet see Table 1 on
page 2 .
July 2005
4
Modification on PPAP references - Errors on part numbers see
Table 1 on page 2.
Nov. 2005
5
Modification on Table 3 on page 5. LM293,A must be 40/+105°C instead of -40/+125°C.
Feb. 2006
6
Unit error for Vol parameter see Table 3 on page 5.
LM193, LM193A, LM293, LM293A, LM393, LM393A
Revision History
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED,
AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS,
NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR
SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2006 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
15/15
Similar pages