Product Folder Sample & Buy Support & Community Tools & Software Technical Documents LM317 SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 LM317 3-Terminal Adjustable Regulator 1 Features 3 Description • The LM317 device is an adjustable three-terminal positive-voltage regulator capable of supplying more than 1.5 A over an output-voltage range of 1.25 V to 37 V. It requires only two external resistors to set the output voltage. The device features a typical line regulation of 0.01% and typical load regulation of 0.1%. It includes current limiting, thermal overload protection, and safe operating area protection. Overload protection remains functional even if the ADJUST terminal is disconnected. 1 • • • • Output Voltage Range Adjustable From 1.25 V to 37 V Output Current Greater Than 1.5 A Internal Short-Circuit Current Limiting Thermal Overload Protection Output Safe-Area Compensation 2 Applications • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • ATCA Solutions DLP: 3D Biometrics, Hyperspectral Imaging, Optical Networking, and Spectroscopy DVR and DVS Desktop PC Digital Signage and Still Camera ECG Electrocardiogram EV HEV Charger: Level 1, 2, and 3 Electronic Shelf Label Energy Harvesting Ethernet Switch Femto Base Station Fingerprint and Iris Biometrics HVAC: Heating, Ventilating, and Air Conditioning High-Speed Data Acquisition and Generation Hydraulic Valve IP Phone: Wired and Wireless Infusion Pump Intelligent Occupancy Sensing Motor Control: Brushed DC, Brushless DC, LowVoltage, Permanent Magnet, and Stepper Motor Point-to-Point Microwave Backhaul Power Bank Solutions Power Line Communication Modem Power Over Ethernet (PoE) Power Quality Meter Power Substation Control Private Branch Exchange (PBX) Programmable Logic Controller RFID Reader Refrigerator Signal or Waveform Generator Software Defined Radio (SDR) Washing Machine: High-End and Low-End X-ray: Baggage Scanner, Medical, and Dental Device Information(1) PART NUMBER LM317 PACKAGE (PIN) BODY SIZE (NOM) SOT (4) 6.50 mm × 3.50 mm TO-220 (3) 10.16 mm × 8.70 mm TO-220 (3) 10.16 mm × 8.59 mm TO-263 (3) 10.18 mm × 8.41 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. 4 Battery-Charger Circuit LM317 VI INPUT RS 0.2 W OUTPUT ADJUST R1 240 W R2 2.4 kW 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LM317 SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 www.ti.com Table of Contents 1 2 3 4 5 6 7 8 Features .................................................................. Applications ........................................................... Description ............................................................. Battery-Charger Circuit ......................................... Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 1 2 3 4 7.1 7.2 7.3 7.4 7.5 7.6 4 4 4 4 5 6 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics........................................... Typical Characteristics .............................................. Detailed Description .............................................. 8 8.1 Overview ................................................................... 8 8.2 Functional Block Diagram ......................................... 8 8.3 Feature Description................................................... 8 8.4 Device Functional Modes.......................................... 9 9 Application and Implementation ........................ 10 9.1 Application Information............................................ 10 9.2 Typical Application .................................................. 10 9.3 System Examples ................................................... 11 10 Power Supply Recommendations ..................... 17 11 Layout................................................................... 17 11.1 Layout Guidelines ................................................. 17 11.2 Layout Example .................................................... 17 12 Device and Documentation Support ................. 18 12.1 Trademarks ........................................................... 18 12.2 Electrostatic Discharge Caution ............................ 18 12.3 Glossary ................................................................ 18 13 Mechanical, Packaging, and Orderable Information ........................................................... 18 5 Revision History Changes from Revision V (February 2013) to Revision W Page • Added Applications, Device Information table, Pin Functions table, ESD Ratings table, Thermal Information table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section. ..................................................................................................................... 1 • Deleted Ordering Information table. ....................................................................................................................................... 1 2 Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 LM317 www.ti.com SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 6 Pin Configuration and Functions OUTPUT INPUT OUTPUT INPUT OUTPUT ADJUST KCS / KCT (TO-220) PACKAGE (TOP VIEW) OUTPUT KC (TO-220) PACKAGE (TOP VIEW) OUTPUT DCY (SOT-223) PACKAGE (TOP VIEW) INPUT OUTPUT ADJUST ADJUST KTT (TO-263) PACKAGE (TOP VIEW) OUTPUT OUTPUT KTE PACKAGE (TOP VIEW) INPUT OUTPUT ADJUST INPUT OUTPUT ADJUST Pin Functions PIN DCY, KCS, KCT, KTT TYPE ADJUST 1 I Output voltage adjustment pin. Connect to a resistor divider to set VO INPUT 3 I Supply input pin OUTPUT 2 O Voltage output pin NAME DESCRIPTION Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 3 LM317 SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 www.ti.com 7 Specifications 7.1 Absolute Maximum Ratings over virtual junction temperature range (unless otherwise noted) (1) MIN VI – VO Input-to-output differential voltage TJ Tstg (1) MAX UNIT 40 V Operating virtual junction temperature 150 °C Lead temperature 1,6 mm (1/16 in) from case for 10 s 260 °C 150 °C Storage temperature range –65 Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 7.2 ESD Ratings MAX V(ESD) (1) (2) Electrostatic discharge Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins (1) 2500 Charged device model (CDM), per JEDEC specification JESD22-C101, all pins (2) 1000 UNIT V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. 7.3 Recommended Operating Conditions MIN VO Output voltage VI – VO Input-to-output differential voltage IO Output current TJ Operating virtual junction temperature MAX UNIT 1.25 7 V 3 40 V 1.5 A 125 °C 0 7.4 Thermal Information LM317 THERMAL METRIC (1) RθJA Junction-to-ambient thermal resistance RθJC(top) Junction-to-case (top) thermal resistance RθJC(bot) Junction-to-case (bottom) thermal resistance (1) 4 DCY KCS KTT 4 PINS 4 PINS 4 PINS 53 19 25.3 30.6 17 18 — 3 1.94 UNIT °C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report (SPRA953). Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 LM317 www.ti.com SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 7.5 Electrical Characteristics over recommended ranges of operating virtual junction temperature (unless otherwise noted) TEST CONDITIONS (1) PARAMETER Line regulation (2) VI – VO = 3 V to 40 V CADJ (3) = 10 μF, TJ = 25°C Load regulation IO = 10 mA to 1500 mA TJ = 0°C to 125°C Thermal regulation 20-ms pulse, MIN TYP MAX TJ = 25°C 0.01 0.04 TJ = 0°C to 125°C 0.02 0.07 25 mV 0.1 0.5 %VO VO ≤ 5 V VO ≥ 5 V 20 70 mV VO ≥ 5 V 0.3 1.5 %VO 0.03 0.07 %VO/W 50 100 μA 0.2 5 μA 1.25 1.3 V TJ = 25°C Change in ADJUST terminal current VI – VO = 2.5 V to 40 V, PD ≤ 20 W, IO = 10 mA to 1500 mA Reference voltage VI – VO = 3 V to 40 V, PD ≤ 20 W, IO = 10 mA to 1500 mA Output-voltage temperature stability TJ = 0°C to 125°C 0.7 Minimum load current to maintain regulation VI – VO = 40 V 3.5 VI – VO ≤ 15 V, PD < PMAX (4) VI – VO ≤ 40 V, PD < PMAX (4), RMS output noise voltage f = 10 Hz to 10 kHz, (% of VO) Ripple rejection VO = 10 V, Long-term stability TJ = 25°C (1) (2) (3) (4) 1.2 TJ = 25°C 1.5 2.2 0.15 0.4 TJ = 25°C f = 120 Hz %/V VO ≤ 5 V ADJUST terminal current Maximum output current UNIT %VO 10 mA A 0.003 CADJ = 0 μF (3) CADJ = 10 μF (3) %VO 57 62 dB 64 0.3 1 %/1k hr Unless otherwise noted, the following test conditions apply: |VI – VO| = 5 V and IOMAX = 1.5 A, TJ = 0°C to 125°C. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Line regulation is expressed here as the percentage change in output voltage per 1-V change at the input. CADJ is connected between the ADJUST terminal and GND. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) – TA) / θJA. Operating at the absolute maximum TJ of 150°C can affect reliability. Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 5 LM317 SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 www.ti.com 7.6 Typical Characteristics 1.4 10.01 TA = 25°C TA = –40°C 1.2 10.005 TA = –40°C 1 0.8 10 V OUT – V V OUT – V TA = 25°C 9.995 TA = 125°C 0.6 0.4 TA = 125°C 0.2 9.99 0 9.985 -0.2 VOUT = VREF VOUT = 10 V Nom -0.4 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 9.98 IOUT – A IOUT – A Figure 2. Load Regulation Figure 1. Load Regulation 11 -1 10.4 -1.5 10.2 10 -3 9.8 -3.5 9.6 -4 -4.5 -2 10 -3 9.8 9.6 9.4 -4 9.4 9.2 -4.5 -68 1.28 -66 1.275 -64 V IN – V 60 70 1.5 1.4 1.3 1.2 1.1 1 0.9 0.8 0.7 V IN = 15 V V OUT = 10 V f = 120 Hz TA = 25°C 0.6 40 35 -50 30 1.24 25 -52 20 1.245 15 -54 10 1.25 5 50 -56 0.5 TA = 125°C -58 0.4 1.26 -60 0.3 TA = 25°C 0.2 1.265 -62 0 TA = –40°C 0.1 Ripple Rejection – dB 1.285 0 40 Figure 4. Load Transient Response 1.27 V OUT – V 30 Tim e – µs Figure 3. Load Transient Response IOUT – A Figure 5. Line Regulation 6 20 -30 9 Tim e – µs 1.255 9.2 CADJ = 10 µF -5 70 60 50 40 30 20 0 10 -10 -20 10.2 VOUT -2.5 9 -30 10.4 -3.5 CADJ = 0 µF -5 10.6 VIN 0 VOUT 10.8 10 -2 -2.5 11 -10 VIN Load Current – A 10.6 V OUT Deviation – V -0.5 -1 -1.5 Load Current – A 0 10.8 -20 0 -0.5 Figure 6. Ripple Rejection vs Output Current Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 LM317 www.ti.com SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 -75 -90 -70 -80 -65 -70 Ripple Rejection – dB Ripple Rejection – dB Typical Characteristics (continued) -60 -55 -50 V IN – V OUT = 15 V IOUT = 500 m A f = 120 Hz TA = 25°C -45 -40 10 15 CADJ = 0 µF -60 CADJ = 10 µF -50 -40 -30 -20 -35 5 V IN = 15 V V OUT = 10 V IOUT = 500 m A TA = 25°C 20 25 30 35 V OUT – V -10 100 100 1k 1000 10k 10000 100k 100000 1M 1000000 Frequency – Hz Figure 7. Ripple Rejection vs Output Voltage Figure 8. Ripple Rejection vs Frequency Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 7 LM317 SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 www.ti.com 8 Detailed Description 8.1 Overview The LM317 device is an adjustable three-terminal positive-voltage regulator capable of supplying more than 1.5 A over an output-voltage range of 1.25 V to 37 V. It requires only two external resistors to set the output voltage. The device features a typical line regulation of 0.01% and typical load regulation of 0.1%. It includes current limiting, thermal overload protection, and safe operating area protection. Overload protection remains functional even if the ADJUST terminal is disconnected. The LM317 device is versatile in its applications, including uses in programmable output regulation and local oncard regulation. Or, by connecting a fixed resistor between the ADJUST and OUTPUT terminals, the LM317 device can function as a precision current regulator. An optional output capacitor can be added to improve transient response. The ADJUST terminal can be bypassed to achieve very high ripple-rejection ratios, which are difficult to achieve with standard three-terminal regulators. 8.2 Functional Block Diagram Input Iadj + 1.25 V Adj. Over Temp & Over Current Protection Output 8.3 Feature Description 8.3.1 NPN Darlington Output Drive NPN Darlington output topology provides naturally low output impedance and an output capacitor is optional. To support maximum current and lowest temperature, 3-V headroom is recommended (VI – VO). 8.3.2 Overload Block Over-current and over-temperature shutdown protects the device against overload or damage from operating in excessive heat. 8.3.3 Programmable Feedback Op amp with 1.25-V offset input at the ADJUST terminal provides easy output voltage or current (not both) programming. For current regulation applications, a single resistor whose resistance value is 1.25 V/IO and power rating is greater than (1.25 V)2/R should be used. For voltage regulation applications, two resistors set the output voltage. 8 Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 LM317 www.ti.com SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 8.4 Device Functional Modes 8.4.1 Normal Operation The device OUTPUT pin will source current necessary to make OUTPUT pin 1.25 V greater than ADJUST terminal to provide output regulation. 8.4.2 Operation With Low Input Voltage The device requires up to 3-V headroom (VI – VO) to operate in regulation. With less headroom, the device may drop out and OUTPUT voltage will be INPUT voltage minus drop out voltage. 8.4.3 Operation at Light Loads The device passes its bias current to the OUTPUT pin. The load or feedback must consume this minimum current for regulation or the output may be too high. 8.4.4 Operation In Self Protection When an overload occurs the device will shut down Darlington NPN output stage or reduce the output current to prevent device damage. The device will automatically reset from the overload. The output may be reduced or alternate between on and off until the overload is removed. Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 9 LM317 SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 www.ti.com 9 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 9.1 Application Information The flexibility of the LM317 allows it to be configured to take on many different functions in DC power applications. 9.2 Typical Application D1 1N4002 Input VI Output LM317 R1 240 W Adjust Ci 0.1 µF VO Vref = 1.25 V IAdj D2 1N4002 CO 1.0 µF CADJ R2 Figure 9. Adjustable Voltage Regulator 9.2.1 Design Requirements • R1 and R2 are required to set the output voltage. • CADJ is recommended to improve ripple rejection. It prevents amplification of the ripple as the output voltage is adjusted higher. • Ci is recommended, particularly if the regulator is not in close proximity to the power-supply filter capacitors. A 0.1-µF disc or 1-µF tantalum capacitor provides sufficient bypassing for most applications, especially when adjustment and output capacitors are used. • CO improves transient response, but is not needed for stability. • Protection diode D2 is recommended if CADJ is used. The diode provides a low-impedance discharge path to prevent the capacitor from discharging into the output of the regulator. • Protection diode D1 is recommended if CO is used. The diode provides a low-impedance discharge path to prevent the capacitor from discharging into the output of the regulator. 9.2.2 Detailed Design Procedure VO is calculated as shown in Equation 1. IADJ is typically 50 µA and negligible in most applications. VO = VREF (1 + R2 / R1) + (IADJ × R2) 10 (1) Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 LM317 www.ti.com SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 Typical Application (continued) 9.2.3 Application Curves 20 10.10 20 10.12 CADJ = 0 µF 10.08 19 18 10.06 18 17 10.04 VOUT 10.10 V IN Change – V VIN 16 V OUT – V V IN Change – V VOUT 10.02 10.08 10.06 17 10.04 VIN V OUT – V 19 CADJ = 10 µF 16 10.02 10.00 Tim e – µs 65 55 45 35 25 15 5 -5 -15 9.98 -25 65 55 45 35 25 14 15 9.98 5 14 -5 15 -15 10.00 -25 15 Tim e – µs Figure 10. Line-Transient Response Figure 11. Line-Transient Response 9.3 System Examples 9.3.1 0-V to 30-V Regulator Circuit æ R + R3 ö VOUT = VREF ç 1 + 2 ÷ - 10 V R1 ø è Here, the voltage is determined by LM317 +35 V INPUT OUTPUT ADJUST VO R1 120 W −10 V C1 0.1 µF R3 680 W R2 3 kW Figure 12. 0-V to 30-V Regulator Circuit Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 11 LM317 SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 www.ti.com System Examples (continued) 9.3.2 Adjustable Regulator Circuit With Improved Ripple Rejection C2 helps to stabilize the voltage at the adjustment pin, which will help reject noise. Diode D1 exists to discharge C2 in case the output is shorted to ground. LM317 VI INPUT VO OUTPUT ADJUST R1 240 W D1 1N4002 C1 0.1 µF C3 1 µF R2 5 kW C2 10 µF Figure 13. Adjustable Regulator Circuit with Improved Ripple Rejection 9.3.3 Precision Current-Limiter Circuit This application will limit the output current to the ILIMIT in the diagram. LM317 VI INPUT Ilimit OUTPUT R1 ADJUST 1.2 R1 Figure 14. Precision Current-Limiter Circuit 9.3.4 Tracking Preregulator Circuit This application keeps a constant voltage across the second LM317 in the circuit. R2 720 Ω ADJUST INPUT VI R1 240 Ω OUTPUT LM317 LM317 INPUT OUTPUT R3 120 Ω ADJUST C1 0.1 µF VO C2 1 µF Output Adjust R4 1 kΩ Figure 15. Tracking Preregulator Circuit 12 Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 LM317 www.ti.com SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 System Examples (continued) 9.3.5 1.25-V to 20-V Regulator Circuit With Minimum Program Current Since the value of VREF is constant, the value of R1 determines the amount of current that flows through R1 and R2. The size of R2 determines the IR drop from ADJUSTMENT to GND. Higher values of R2 translate to higher VOUT. LM317 INPUT VI OUTPUT ADJUST VO R1 1.2 kΩ R2 20 kΩ Figure 16. 1.25-V to 20-V Regulator Circuit With Minimum Program Current 9.3.6 Adjusting Multiple On-Card Regulators With a Single Control With different values of R1 for each LM317, R2 can be chosen such that each LM317 outputs a different voltage. LM317 VI INPUT LM317 OUTPUT ADJUST VO INPUT VI R1 120 W OUTPUT LM317 VO ADJUST VI INPUT OUTPUT VO ADJUST R2 1 kW Figure 17. Adjusting Multiple On-Card Regulators With a Single Control 9.3.7 Battery-Charger Circuit The series resistor limits the current output of the LM317, minimizing damage to the battery cell. LM317 VI INPUT RS 0.2 W OUTPUT ADJUST R1 240 W R2 2.4 kW Figure 18. Battery-Charger Circuit Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 13 LM317 SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 www.ti.com System Examples (continued) 9.3.8 50-mA Constant-Current Battery-Charger Circuit The current limit operation mode can be used to trickle charge a battery at a fixed current. ICHG = 1.25V÷24Ω. VI should be greater than VBAT + 4.25 V. (1.25V [VREF]+ 3V [headroom]) LM317 VI INPUT 24 Ω OUTPUT ADJUST Figure 19. 50-mA Constant-Current Battery-Charger Circuit 9.3.9 Slow Turn-On 15-V Regulator Circuit The capacitor C1, in combination with the PNP transistor, helps the circuit to slowly start supplying voltage. In the beginning, the capacitor is not charged. Therefore output voltage will start at VC1+ VBE + 1.25V = 0V + 0.65V + 1.25V = 1.9V. As the capacitor voltage rises, VOUT will as rise at the same rate. When the output voltage reaches the value determined by R1 and R2, the PNP will be turned off. LM317 VI INPUT OUTPUT VO = 15 V R1 240 Ω ADJUST D1 1N4002 R3 50 kΩ R2 2.7 kΩ 2N2905 C1 25 µF Figure 20. Slow Turn-On 15-V Regulator Circuit 9.3.10 AC Voltage-Regulator Circuit These two LM317s can regulate both the positive and negative swings of a sinusoidal AC input. LM317 VI INPUT OUTPUT ADJUST 480 Ω 12 VI(PP) 120 Ω 480 Ω ADJUST VI INPUT 120 Ω 6 VO(PP) 2 W (TYP) OUTPUT LM317 Figure 21. AC Voltage-Regulator Circuit 14 Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 LM317 www.ti.com SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 System Examples (continued) 9.3.11 Current-Limited 6-V Charger Circuit As the charge current increases, the voltage at the bottom resistor increases until the NPN starts sinking current from the adjustment pin. The voltage at the adjustment pin will drop, and consequently the output voltage will decrease until the NPN stops conducting. LM317 INPUT VI+ OUTPUT ADJUST R1 240 W R2 1.1 kW R3 VI− Figure 22. Current-Limited 6-V Charger Circuit 9.3.12 Adjustable 4-A Regulator Circuit This application keeps the output current at 4 A while having the ability to adjust the output voltage using the adjustable (1.5 kΩ in schematic) resistor. LM317 VI INPUT 0.2 Ω OUTPUT ADJUST LM317 INPUT 0.2 Ω OUTPUT ADJUST 4.5 V to 25 V LM317 INPUT 0.2 Ω OUTPUT ADJUST 5 kΩ 100 Ω TL080 + 2N2905 5 kΩ _ 150 Ω 200 pF 1.5 kΩ Figure 23. Adjustable 4-A Regulator Circuit Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 15 LM317 SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 www.ti.com System Examples (continued) 9.3.13 High-Current Adjustable Regulator Circuit The NPNs at the top of the schematic allow higher currents at VOUT than the LM317 can provide, while still keeping the output voltage at levels determined by the adjustment pin resistor divider of the LM317. TIP73 2N2905 VI 500 W 5 kW 22 W LM317 INPUT VO OUTPUT ADJUST 120 W 1N4002 10 µF 47 µF 10 µF Figure 24. High-Current Adjustable Regulator Circuit 16 Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 LM317 www.ti.com SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 10 Power Supply Recommendations The LM317 is designed to operate from an input voltage supply range between 1.25 V to 37 V greater than the output voltage. If the device is more than six inches from the input filter capacitors, an input bypass capacitor, 0.1 μF or greater, of any type is needed for stability. 11 Layout 11.1 Layout Guidelines • • • It is recommended that the input terminal be bypassed to ground with a bypass capacitor. The optimum placement is closest to the input terminal of the device and the system GND. Care must be taken to minimize the loop area formed by the bypass-capacitor connection, the input terminal, and the system GND. For operation at full rated load, it is recommended to use wide trace lengths to eliminate I × R drop and heat dissipation. 11.2 Layout Example OUTPUT Ground COUT R2 Power INPUT OUTPUT R1 ADJ/GND Cadj High Frequency Bypass Capacitor 0.1μF 10μF High Input Bypass Capacitor Ground Figure 25. Layout Example Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 17 LM317 SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014 www.ti.com 12 Device and Documentation Support 12.1 Trademarks All trademarks are the property of their respective owners. 12.2 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 12.3 Glossary SLYZ022 — TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 13 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 18 Submit Documentation Feedback Copyright © 1997–2014, Texas Instruments Incorporated Product Folder Links: LM317 PACKAGE OPTION ADDENDUM www.ti.com 7-Mar-2014 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LM317DCY ACTIVE SOT-223 DCY 4 80 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR 0 to 125 L3 LM317DCYG3 ACTIVE SOT-223 DCY 4 80 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR 0 to 125 L3 LM317DCYR ACTIVE SOT-223 DCY 4 2500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR 0 to 125 L3 LM317DCYRG3 ACTIVE SOT-223 DCY 4 2500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR 0 to 125 L3 LM317KC OBSOLETE TO-220 KC 3 TBD Call TI Call TI 0 to 125 LM317 LM317KCE3 OBSOLETE TO-220 KC 3 TBD Call TI Call TI 0 to 125 LM317 LM317KCS ACTIVE TO-220 KCS 3 50 Pb-Free (RoHS) CU SN N / A for Pkg Type 0 to 125 LM317 LM317KCSE3 ACTIVE TO-220 KCS 3 50 Pb-Free (RoHS) CU SN N / A for Pkg Type 0 to 125 LM317 LM317KCT ACTIVE TO-220 KCT 3 50 Pb-Free (RoHS) CU SN N / A for Pkg Type 0 to 125 LM317 LM317KTER OBSOLETE PFM KTE 3 TBD Call TI Call TI 0 to 125 LM317 LM317KTTR ACTIVE DDPAK/ TO-263 KTT 3 500 Green (RoHS & no Sb/Br) CU SN Level-3-245C-168 HR 0 to 125 LM317 LM317KTTRG3 ACTIVE DDPAK/ TO-263 KTT 3 500 Green (RoHS & no Sb/Br) CU SN Level-3-245C-168 HR 0 to 125 LM317 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 7-Mar-2014 Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 29-Apr-2016 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) LM317DCYR SOT-223 DCY 4 2500 330.0 12.4 LM317DCYR SOT-223 DCY 4 2500 330.0 LM317KTTR DDPAK/ TO-263 KTT 3 500 330.0 LM317KTTR DDPAK/ TO-263 KTT 3 500 330.0 7.05 7.4 1.9 8.0 12.0 Q3 12.4 6.55 7.25 1.9 1.5 12.0 Q3 24.4 10.8 16.1 4.9 16.0 24.0 Q2 24.4 10.8 16.3 5.11 16.0 24.0 Q2 Pack Materials-Page 1 W Pin1 (mm) Quadrant PACKAGE MATERIALS INFORMATION www.ti.com 29-Apr-2016 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM317DCYR SOT-223 DCY 4 2500 340.0 340.0 38.0 LM317DCYR SOT-223 DCY 4 2500 336.0 336.0 48.0 LM317KTTR DDPAK/TO-263 KTT 3 500 350.0 334.0 47.0 LM317KTTR DDPAK/TO-263 KTT 3 500 340.0 340.0 38.0 Pack Materials-Page 2 MECHANICAL DATA MPDS094A – APRIL 2001 – REVISED JUNE 2002 DCY (R-PDSO-G4) PLASTIC SMALL-OUTLINE 6,70 (0.264) 6,30 (0.248) 3,10 (0.122) 2,90 (0.114) 4 0,10 (0.004) M 3,70 (0.146) 3,30 (0.130) 7,30 (0.287) 6,70 (0.264) Gauge Plane 1 2 0,84 (0.033) 0,66 (0.026) 2,30 (0.091) 4,60 (0.181) 1,80 (0.071) MAX 3 0°–10° 0,10 (0.004) M 0,25 (0.010) 0,75 (0.030) MIN 1,70 (0.067) 1,50 (0.059) 0,35 (0.014) 0,23 (0.009) Seating Plane 0,08 (0.003) 0,10 (0.0040) 0,02 (0.0008) 4202506/B 06/2002 NOTES: A. B. C. D. All linear dimensions are in millimeters (inches). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion. Falls within JEDEC TO-261 Variation AA. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MPFM001E – OCTOBER 1994 – REVISED JANUARY 2001 KTE (R-PSFM-G3) PowerFLEX PLASTIC FLANGE-MOUNT 0.375 (9,52) 0.080 (2,03) 0.070 (1,78) 0.365 (9,27) 0.360 (9,14) 0.050 (1,27) 0.040 (1,02) 0.350 (8,89) 0.220 (5,59) NOM 0.010 (0,25) NOM Thermal Tab (See Note C) 0.360 (9,14) 0.350 (8,89) 0.295 (7,49) NOM 0.320 (8,13) 0.310 (7,87) 0.420 (10,67) 0.410 (10,41) 1 3 0.025 (0,63) 0.031 (0,79) 0.100 (2,54) Seating Plane 0.004 (0,10) 0.010 (0,25) M 0.005 (0,13) 0.001 (0,03) 0.200 (5,08) 0.041 (1,04) 0.031 (0,79) 0.010 (0,25) NOM Gage Plane 3°– 6° 0.010 (0,25) 4073375/F 12/00 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. The center lead is in electrical contact with the thermal tab. Dimensions do not include mold protrusions, not to exceed 0.006 (0,15). Falls within JEDEC MO-169 PowerFLEX is a trademark of Texas Instruments. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 PACKAGE OUTLINE KCS0003B TO-220 - 19.65 mm max height SCALE 0.850 TO-220 4.7 4.4 10.36 9.96 1.32 1.22 2.9 2.6 6.5 6.1 8.55 8.15 (6.3) ( 3.84) 12.5 12.1 19.65 MAX 9.25 9.05 3X 3.9 MAX 13.12 12.70 3 1 3X 3X 0.47 0.34 0.90 0.77 2.79 2.59 2X 2.54 1.36 1.23 5.08 4222214/A 10/2015 NOTES: 1. All controlling linear dimensions are in inches. Dimensions in brackets are in millimeters. Any dimension in brackets or parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Reference JEDEC registration TO-220. www.ti.com EXAMPLE BOARD LAYOUT KCS0003B TO-220 - 19.65 mm max height TO-220 0.07 MAX ALL AROUND 3X 2X (1.7) METAL (1.2) 2X SOLDER MASK OPENING (1.7) R (0.05) SOLDER MASK OPENING 2 1 (2.54) 3 0.07 MAX ALL AROUND (5.08) LAND PATTERN EXAMPLE NON-SOLDER MASK DEFINED SCALE:15X 4222214/A 10/2015 www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2016, Texas Instruments Incorporated