LM5574/LM5574Q SIMPLE SWITCHER® 75V, 0.5A Step-Down Switching Regulator General Description Features The LM5574 is an easy to use SIMPLE SWITCHER® buck regulator which allows design engineers to design and optimize a robust power supply using a minimum set of components. Operating with an input voltage range of 6 - 75V, the LM5574 delivers 0.5A of continuous output current with an integrated 750mΩ N-Channel MOSFET. The regulator utilizes an Emulated Current Mode architecture which provides inherent line regulation, tight load transient response, and ease of loop compensation without the usual limitation of lowduty cycles associated with current mode regulators. The operating frequency is adjustable from 50kHz to 500kHz to allow optimization of size and efficiency. To reduce EMI, a frequency synchronization pin allows multiple IC’s from the LM(2)557x family to self-synchronize or to synchronize to an external clock. The LM5574 guarantees robustness with cycle-by-cycle current limit, short-circuit protection, thermal shut-down, and remote shut-down. The device is available in a TSSOP-16 package. The LM5574 is supported by the full suite of WEBENCH® On-Line design tools. ■ LM5574Q is an Automotive Grade product that is AEC■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Q100 grade 1 qualified (−40°C to + 125°C operating junction temperature) Integrated 75V, 750mΩ N-channel MOSFET Ultra-wide input voltage range from 6V to 75V Adjustable output voltage as low as 1.225V 1.5% feedback reference accuracy Operating frequency adjustable between 50kHz and 500kHz with single resistor Master or slave frequency synchronization Adjustable soft-start Emulated current mode control architecture Wide bandwidth error amplifier Built-in protection Automotive Grade product datasheet that is AEC-Q100 grade 0 qualified is available upon request (−40°C to + 150°C operating junction temperature) Package ■ TSSOP-16 Applications ■ Automotive ■ Industrial Simplified Application Schematic 20212001 WEBENCH® is a registered trademark of National Semiconductor Corporation. © 2009 National Semiconductor Corporation 202120 www.national.com LM5574/LM5574Q SIMPLE SWITCHER® 75V, 0.5A Step-Down Switching Regulator March 23, 2009 LM5574/LM5574Q Connection Diagram 20212002 Top View 16-Lead TSSOP Ordering Information Order Number Package Type NSC Package Drawing Supplied As LM5574MT TSSOP-16 MTC16 92 Units in Rail LM5574MTX TSSOP-16 MTC16 2500 Units on Tape and Reel LM5574QMT TSSOP-16 MTC16 92 Units in Rail LM5574QMTX TSSOP-16 MTC16 2500 Units on Tape and Reel Features AEC-Q100 Grade 1 qualified. Automotive Grade Production Flow * * Automotive Grade (Q) product incorporates enhanced manufacturing and support processes for the automotive market, including defect detection methodologies. Reliability qualification is compliant with the requirements and temperature grades defined in the AEC-Q100 standard. Automotive grade products are identified with the letter Q. For more information go to http://www.national.com/automotive. www.national.com 2 Pin(s) Name 1 VCC 2 Description Application Information Output of the bias regulator Vcc tracks Vin up to 9V. Beyond 9V, Vcc is regulated to 7 Volts. A 0.1uF to 1uF ceramic decoupling capacitor is required. An external voltage (7.5V – 14V) can be applied to this pin to reduce internal power dissipation. SD Shutdown or UVLO input If the SD pin voltage is below 0.7V the regulator will be in a low power state. If the SD pin voltage is between 0.7V and 1.225V the regulator will be in standby mode. If the SD pin voltage is above 1.225V the regulator will be operational. An external voltage divider can be used to set a line undervoltage shutdown threshold. If the SD pin is left open circuit, a 5µA pull-up current source configures the regulator fully operational. 3 Vin Input supply voltage Nominal operating range: 6V to 75V 4 SYNC Oscillator synchronization input or output The internal oscillator can be synchronized to an external clock with an external pull-down device. Multiple LM5574 devices can be synchronized together by connection of their SYNC pins. 5 COMP Output of the internal error amplifier The loop compensation network should be connected between this pin and the FB pin. 6 FB Feedback signal from the regulated output This pin is connected to the inverting input of the internal error amplifier. The regulation threshold is 1.225V. 7 RT Internal oscillator frequency set input The internal oscillator is set with a single resistor, connected between this pin and the AGND pin. 8 RAMP Ramp control signal An external capacitor connected between this pin and the AGND pin sets the ramp slope used for current mode control. Recommended capacitor range 50pF to 2000pF. Analog ground Internal reference for the regulator control functions Soft-start An external capacitor and an internal 10µA current source set the time constant for the rise of the error amp reference. The SS pin is held low during standby, Vcc UVLO and thermal shutdown. Output voltage connection Connect directly to the regulated output voltage. 9 AGND 10 SS 11 OUT 12 PGND Power ground Low side reference for the PRE switch and the IS sense resistor. 13 IS Current sense Current measurement connection for the re-circulating diode. An internal sense resistor and a sample/hold circuit sense the diode current near the conclusion of the off-time. This current measurement provides the DC level of the emulated current ramp. 14 SW Switching node The source terminal of the internal buck switch. The SW pin should be connected to the external Schottky diode and to the buck inductor. 15 PRE Pre-charge assist for the bootstrap capacitor This open drain output can be connected to SW pin to aid charging the bootstrap capacitor during very light load conditions or in applications where the output may be precharged before the LM5574 is enabled. An internal precharge MOSFET is turned on for 250ns each cycle just prior to the on-time interval of the buck switch. 16 BST Boost input for bootstrap capacitor An external capacitor is required between the BST and the SW pins. A 0.022µF ceramic capacitor is recommended. The capacitor is charged from Vcc via an internal diode during the off-time of the buck switch. 3 www.national.com LM5574/LM5574Q Pin Descriptions LM5574/LM5574Q BST to SW OUT to GND SYNC, SS, FB, RAMP to GND ESD Rating (Note 2) Human Body Model Storage Temperature Range Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VIN to GND BST to GND PRE to GND SW to GND (Steady State) BST to VCC SD, VCC to GND 76V 90V 76V -1.5V 76V 14V 14V Limited to Vin 7V 2kV -65°C to +150°C Operating Ratings (Note 1) VIN Operation Junction Temperature 6V to 75V −40°C to + 125°C Electrical Characteristics Specifications with standard typeface are for TJ = 25°C, and those with boldface type apply over full Operating Junction Temperature range. VIN = 48V, RT = 32.4kΩ unless otherwise stated. (Note 3) Symbol Parameter Conditions Min Typ Max Units 6.85 7.15 7.45 V STARTUP REGULATOR VccReg Vcc Regulator Output Vcc LDO Mode turn-off Vcc Current Limit Vcc = 0V Vcc UVLO Threshold (Vcc increasing) 9 V 25 mA VCC SUPPLY 5.03 Vcc Undervoltage Hysteresis 5.35 5.67 V 0.35 V Bias Current (Iin) FB = 1.3V 3.7 4.5 mA Shutdown Current (Iin) SD = 0V 57 85 µA 0.9 V SHUTDOWN THRESHOLDS Shutdown Threshold (SD Increasing) 0.47 0.7 (Standby Increasing) 1.17 1.225 Shutdown Hysteresis Standby Threshold 0.1 Standby Hysteresis SD Pull-up Current Source V 1.28 V 0.1 V 5 µA SWITCH CHARACTERSICS Buck Switch Rds(on) 750 BOOST UVLO 1500 mΩ 4 V BOOST UVLO Hysteresis 0.56 V Pre-charge Switch Rds(on) 70 Pre-charge Switch on-time 250 Ω ns CURRENT LIMIT Cycle by Cycle Current Limit RAMP = 0V Cycle by Cycle Current Limit Delay RAMP = 2.5V 0.6 0.7 0.8 75 A ns SOFT-START SS Current Source 7 10 14 µA 180 200 220 kHz 425 485 545 kHz OSCILLATOR Frequency1 Frequency2 RT = 11kΩ SYNC Source Impedance 11 kΩ SYNC Sink Impedance 110 SYNC Threshold (falling) 1.3 Ω V SYNC Frequency RT = 11kΩ SYNC Pulse Width Minimum www.national.com 4 550 kHz 15 ns Parameter Conditions Min Typ Max Units RAMP GENERATOR Ramp Current 1 Vin = 60V, Vout=10V 467 550 633 µA Ramp Current 2 Vin = 10V, Vout=10V 36 50 64 µA 416 500 575 ns PWM COMPARATOR Forced Off-time Min On-time 80 ns COMP to PWM Comparator Offset 0.7 V ERROR AMPLIFIER Feedback Voltage Vfb = COMP 1.207 FB Bias Current 1.225 V 1.243 17 DC Gain nA 70 COMP Sink / Source Current dB mA 3 Unity Gain Bandwidth 3 MHz 250 mΩ Thermal Shutdown Threshold 165 °C Thermal Shutdown Hysteresis 25 °C DIODE SENSE RESISTANCE DSENSE THERMAL SHUTDOWN Tsd THERMAL RESISTANCE θJC Junction to Case 30 °C/W θJA Junction to Ambient 90 °C/W Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is intended to be functional. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: The human body model is a 100pF capacitor discharged through a 1.5kΩ resistor into each pin. Note 3: Min and Max limits are 100% production tested at 25°C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control (SQC) methods. Limits are used to calculate National’s Average Outgoing Quality Level (AOQL). Typical Performance Characteristics Oscillator Frequency vs RT Oscillator Frequency vs Temperature FOSC = 200kHz 20212020 20212021 5 www.national.com LM5574/LM5574Q Symbol LM5574/LM5574Q Soft Start Current vs Temperature VCC vs ICC VIN = 12V 20212022 20212023 VCC vs VIN RL = 7kΩ Error Amplifier Gain/Phase AVCL = 101 20212025 20212024 Demoboard Efficiency vs IOUT and VIN 20212026 www.national.com 6 LM5574/LM5574Q FIGURE 1. 20212003 Typical Application Circuit and Block Diagram 7 www.national.com LM5574/LM5574Q (VIN) can be connected directly to the input voltage, as high as 75 Volts. For input voltages below 9V, a low dropout switch connects Vcc directly to Vin. In this supply range, Vcc is approximately equal to Vin. For Vin voltage greater than 9V, the low dropout switch is disabled and the Vcc regulator is enabled to maintain Vcc at approximately 7V. The wide operating range of 6V to 75V is achieved through the use of this dual mode regulator. The output of the Vcc regulator is current limited to 25mA. Upon power up, the regulator sources current into the capacitor connected to the VCC pin. When the voltage at the VCC pin exceeds the Vcc UVLO threshold of 5.35V and the SD pin is greater than 1.225V, the output switch is enabled and a softstart sequence begins. The output switch remains enabled until Vcc falls below 5.0V or the SD pin falls below 1.125V. An auxiliary supply voltage can be applied to the Vcc pin to reduce the IC power dissipation. If the auxiliary voltage is greater than 7.3V, the internal regulator will essentially shut off, reducing the IC power dissipation. The Vcc regulator series pass transistor includes a diode between Vcc and Vin that should not be forward biased in normal operation. Therefore the auxiliary Vcc voltage should never exceed the Vin voltage. In high voltage applications extra care should be taken to ensure the VIN pin does not exceed the absolute maximum voltage rating of 76V. During line or load transients, voltage ringing on the Vin line that exceeds the Absolute Maximum Ratings can damage the IC. Both careful PC board layout and the use of quality bypass capacitors located close to the VIN and GND pins are essential. Detailed Operating Description The LM5574 switching regulator features all of the functions necessary to implement an efficient high voltage buck regulator using a minimum of external components. This easy to use regulator integrates a 75V N-Channel buck switch with an output current capability of 0.5 Amps. The regulator control method is based on current mode control utilizing an emulated current ramp. Peak current mode control provides inherent line voltage feed-forward, cycle-by-cycle current limiting, and ease of loop compensation. The use of an emulated control ramp reduces noise sensitivity of the pulse-width modulation circuit, allowing reliable processing of very small duty cycles necessary in high input voltage applications. The operating frequency is user programmable from 50kHz to 500kHz. An oscillator synchronization pin allows multiple LM5574 regulators to self synchronize or be synchronized to an external clock. The output voltage can be set as low as 1.225V. Fault protection features include, current limiting, thermal shutdown and remote shutdown capability. The device is available in the TSSOP-16 package. The functional block diagram and typical application of the LM5574 are shown in Figure 1. The LM5574 can be applied in numerous applications to efficiently step-down a high, unregulated input voltage. The device is well suited for telecom, industrial and automotive power bus voltage ranges. High Voltage Start-Up Regulator The LM5574 contains a dual-mode internal high voltage startup regulator that provides the Vcc bias supply for the PWM controller and boot-strap MOSFET gate driver. The input pin 20212004 FIGURE 2. Vin and Vcc Sequencing www.national.com 8 LM5574/LM5574Q Shutdown / Standby The LM5574 contains a dual level Shutdown (SD) circuit. When the SD pin voltage is below 0.7V, the regulator is in a low current shutdown mode. When the SD pin voltage is greater than 0.7V but less than 1.225V, the regulator is in standby mode. In standby mode the Vcc regulator is active but the output switch is disabled. When the SD pin voltage exceeds 1.225V, the output switch is enabled and normal operation begins. An internal 5µA pull-up current source configures the regulator to be fully operational if the SD pin is left open. An external set-point voltage divider from VIN to GND can be used to set the operational input range of the regulator. The divider must be designed such that the voltage at the SD pin will be greater than 1.225V when Vin is in the desired operating range. The internal 5µA pull-up current source must be included in calculations of the external set-point divider. Hysteresis of 0.1V is included for both the shutdown and standby thresholds. The SD pin is internally clamped with a 1kΩ resistor and an 8V zener clamp. The voltage at the SD pin should never exceed 14V. If the voltage at the SD pin exceeds 8V, the bias current will increase at a rate of 1 mA/V. The SD pin can also be used to implement various remote enable / disable functions. Pulling the SD pin below the 0.7V threshold totally disables the controller. If the SD pin voltage is above 1.225V the regulator will be operational. 20212006 FIGURE 4. Sync from Multiple Devices Multiple LM5574 devices can be synchronized together simply by connecting the SYNC pins together. In this configuration all of the devices will be synchronized to the highest frequency device. The diagram in Figure 5 illustrates the SYNC input/output features of the LM5574. The internal oscillator circuit drives the SYNC pin with a strong pull-down / weak pull-up inverter. When the SYNC pin is pulled low either by the internal oscillator or an external clock, the ramp cycle of the oscillator is terminated and a new oscillator cycle begins. Thus, if the SYNC pins of several LM5574 IC’s are connected together, the IC with the highest internal clock frequency will pull the connected SYNC pins low first and terminate the oscillator ramp cycles of the other IC’s. The LM5574 with the highest programmed clock frequency will serve as the master and control the switching frequency of the all the devices with lower oscillator frequency. Oscillator and Sync Capability The LM5574 oscillator frequency is set by a single external resistor connected between the RT pin and the AGND pin. The RT resistor should be located very close to the device and connected directly to the pins of the IC (RT and AGND).To set a desired oscillator frequency (F), the necessary value for the RT resistor can be calculated from the following equation: The SYNC pin can be used to synchronize the internal oscillator to an external clock. The external clock must be of higher frequency than the free-running frequency set by the RT resistor. A clock circuit with an open drain output is the recommended interface from the external clock to the SYNC pin. The clock pulse duration should be greater than 15ns. 20212005 FIGURE 3. Sync from External Clock 9 www.national.com LM5574/LM5574Q 20212007 FIGURE 5. Simplified Oscillator Block Diagram and SYNC I/O Circuit Error Amplifier and PWM Comparator RAMP Generator The ramp signal used in the pulse width modulator for current mode control is typically derived directly from the buck switch current. This switch current corresponds to the positive slope portion of the output inductor current. Using this signal for the PWM ramp simplifies the control loop transfer function to a single pole response and provides inherent input voltage feed-forward compensation. The disadvantage of using the buck switch current signal for PWM control is the large leading edge spike due to circuit parasitics that must be filtered or blanked. Also, the current measurement may introduce significant propagation delays. The filtering, blanking time and propagation delay limit the minimum achievable pulsewidth. In applications where the input voltage may be relatively large in comparison to the output voltage, controlling small pulsewidths and duty cycles is necessary for regulation. The LM5574 utilizes a unique ramp generator, which does not actually measure the buck switch current but rather reconstructs the signal. Reconstructing or emulating the inductor current provides a ramp signal to the PWM comparator that is free of leading edge spikes and measurement or filtering delays. The current reconstruction is comprised of two elements; a sample & hold DC level and an emulated current ramp. The internal high gain error amplifier generates an error signal proportional to the difference between the regulated output voltage and an internal precision reference (1.225V). The output of the error amplifier is connected to the COMP pin allowing the user to provide loop compensation components, generally a type II network, as illustrated in Figure 1. This network creates a pole at DC, a zero and a noise reducing high frequency pole. The PWM comparator compares the emulated current sense signal from the RAMP generator to the error amplifier output voltage at the COMP pin. www.national.com 10 LM5574/LM5574Q 20212008 FIGURE 6. Composition of Current Sense Signal The sample & hold DC level illustrated in Figure 6 is derived from a measurement of the re-circulating Schottky diode anode current. The re-circulating diode anode should be connected to the IS pin. The diode current flows through an internal current sense resistor between the IS and PGND pins. The voltage level across the sense resistor is sampled and held just prior to the onset of the next conduction interval of the buck switch. The diode current sensing and sample & hold provide the DC level of the reconstructed current signal. The positive slope inductor current ramp is emulated by an external capacitor connected from the RAMP pin to AGND and an internal voltage controlled current source. The ramp current source that emulates the inductor current is a function of the Vin and Vout voltages per the following equation: oscillation is normally characterized by observing alternating wide and narrow pulses at the switch node. Adding a fixed slope voltage ramp (slope compensation) to the current sense signal prevents this oscillation. The 50µA of offset current provided from the emulated current source adds some fixed slope to the ramp signal. In some high output voltage, high duty cycle applications, additional slope may be required. In these applications, a pull-up resistor may be added between the VCC and RAMP pins to increase the ramp slope compensation. For VOUT > 7.5V: Calculate optimal slope current, IOS = VOUT x 10µA/V. For example, at VOUT = 10V, IOS = 100µA. Install a resistor from the RAMP pin to VCC: RRAMP = VCC / (IOS - 50µA) IRAMP = (10µ x (Vin – Vout)) + 50µA Proper selection of the RAMP capacitor depends upon the selected value of the output inductor. The value of CRAMP can be selected from: CRAMP = L x 5 x 10-6, where L is the value of the output inductor in Henrys. With this value, the scale factor of the emulated current ramp will be approximately equal to the scale factor of the DC level sample and hold (2.0V / A). The CRAMP capacitor should be located very close to the device and connected directly to the pins of the IC (RAMP and AGND). For duty cycles greater than 50%, peak current mode control circuits are subject to sub-harmonic oscillation. Sub-harmonic 20212045 FIGURE 7. RRAMP to VCC for VOUT > 7.5V 11 www.national.com LM5574/LM5574Q stresses and surges. The internal soft-start current source, set to 10µA, gradually increases the voltage of an external soft-start capacitor connected to the SS pin. The soft-start capacitor voltage is connected to the reference input of the error amplifier. Various sequencing and tracking schemes can be implemented using external circuits that limit or clamp the voltage level of the SS pin. In the event a fault is detected (over-temperature, Vcc UVLO, SD) the soft-start capacitor will be discharged. When the fault condition is no longer present a new soft-start sequence will commence. Maximum Duty Cycle / Input Dropout Voltage There is a forced off-time of 500ns implemented each cycle to guarantee sufficient time for the diode current to be sampled. This forced off-time limits the maximum duty cycle of the buck switch. The maximum duty cycle will vary with the operating frequency. DMAX = 1 - Fs x 500ns Where Fs is the oscillator frequency. Limiting the maximum duty cycle will raise the input dropout voltage. The input dropout voltage is the lowest input voltage required to maintain regulation of the output voltage. An approximation of the input dropout voltage is: Boost Pin The LM5574 integrates an N-Channel buck switch and associated floating high voltage level shift / gate driver. This gate driver circuit works in conjunction with an internal diode and an external bootstrap capacitor. A 0.022µF ceramic capacitor, connected with short traces between the BST pin and SW pin, is recommended. During the off-time of the buck switch, the SW pin voltage is approximately -0.5V and the bootstrap capacitor is charged from Vcc through the internal bootstrap diode. When operating with a high PWM duty cycle, the buck switch will be forced off each cycle for 500ns to ensure that the bootstrap capacitor is recharged. Under very light load conditions or when the output voltage is pre-charged, the SW voltage will not remain low during the off-time of the buck switch. If the inductor current falls to zero and the SW pin rises, the bootstrap capacitor will not receive sufficient voltage to operate the buck switch gate driver. For these applications, the PRE pin can be connected to the SW pin to pre-charge the bootstrap capacitor. The internal precharge MOSFET and diode connected between the PRE pin and PGND turns on each cycle for 250ns just prior to the onset of a new switching cycle. If the SW pin is at a normal negative voltage level (continuous conduction mode), then no current will flow through the pre-charge MOSFET/diode. Where VD is the voltage drop across the re-circulatory diode. Operating at high switching frequency raises the minimum input voltage necessary to maintain regulation. Current Limit The LM5574 contains a unique current monitoring scheme for control and over-current protection. When set correctly, the emulated current sense signal provides a signal which is proportional to the buck switch current with a scale factor of 2.0 V / A. The emulated ramp signal is applied to the current limit comparator. If the emulated ramp signal exceeds 1.4V (0.7A) the present current cycle is terminated (cycle-by-cycle current limiting). In applications with small output inductance and high input voltage the switch current may overshoot due to the propagation delay of the current limit comparator. If an overshoot should occur, the diode current sampling circuit will detect the excess inductor current during the off-time of the buck switch. If the sample & hold DC level exceeds the 1.4V current limit threshold, the buck switch will be disabled and skip pulses until the diode current sampling circuit detects the inductor current has decayed below the current limit threshold. This approach prevents current runaway conditions due to propagation delays or inductor saturation since the inductor current is forced to decay following any current overshoot. Thermal Protection Internal Thermal Shutdown circuitry is provided to protect the integrated circuit in the event the maximum junction temperature is exceeded. When activated, typically at 165°C, the controller is forced into a low power reset state, disabling the output driver and the bias regulator. This feature is provided to prevent catastrophic failures from accidental device overheating. Soft-Start The soft-start feature allows the regulator to gradually reach the initial steady state operating point, thus reducing start-up www.national.com 12 EXTERNAL COMPONENTS The procedure for calculating the external components is illustrated with the following design example. The Bill of Materials for this design is listed in Table 1. The circuit shown in Figure 1 is configured for the following specifications: • VOUT = 5V • VIN = 7V to 75V • Fs = 300kHz • Minimum load current (for CCM) = 100mA • Maximum load current = 0.5A C3 (CRAMP) With the inductor value selected, the value of C3 (CRAMP) necessary for the emulation ramp circuit is: CRAMP = L x 5 x 10-6 Where L is in Henrys With L1 selected for 100µH the recommended value for C3 is 470pF (nearest standard value). R3 (RT) RT sets the oscillator switching frequency. Generally, higher frequency applications are smaller but have higher losses. Operation at 300kHz was selected for this example as a reasonable compromise for both small size and high efficiency. The value of RT for 300kHz switching frequency can be calculated as follows: C9 The output capacitor, C9 smoothes the inductor ripple current and provides a source of charge for transient loading conditions. For this design a 22µF ceramic capacitor was selected. The ceramic capacitor provides ultra low ESR to reduce the output ripple voltage and noise spikes. An approximation for the output ripple voltage is: The nearest standard value of 21kΩ was chosen for RT. L1 The inductor value is determined based on the operating frequency, load current, ripple current, and the minimum and maximum input voltage (VIN(min), VIN(max)). D1 A Schottky type re-circulating diode is required for all LM5574 applications. Ultra-fast diodes are not recommended and may result in damage to the IC due to reverse recovery current transients. The near ideal reverse recovery characteristics and low forward voltage drop are particularly important diode characteristics for high input voltage and low output voltage applications common to the LM5574. The reverse recovery characteristic determines how long the current surge lasts each cycle when the buck switch is turned on. The reverse recovery characteristics of Schottky diodes minimize the peak instantaneous power in the buck switch occurring during turnon each cycle. The resulting switching losses of the buck switch are significantly reduced when using a Schottky diode. The reverse breakdown rating should be selected for the maximum VIN, plus some safety margin. The forward voltage drop has a significant impact on the conversion efficiency, especially for applications with a low output voltage. “Rated” current for diodes vary widely from various manufacturers. The worst case is to assume a short circuit load condition. In this case the diode will carry the output current almost continuously. For the LM5574 this current can be as high as 0.7A. Assuming a worst case 1V drop across the diode, the maximum diode power dissipation can be as high as 0.7W. For the reference design a 100V Schottky in a SMA package was selected. 20212010 FIGURE 8. Inductor Current Waveform To keep the circuit in continuous conduction mode (CCM), the maximum ripple current IRIPPLE should be less than twice the minimum load current, or 0.2Ap-p. Using this value of ripple current, the value of inductor (L1) is calculated using the following: C1 The regulator supply voltage has a large source impedance at the switching frequency. Good quality input capacitors are necessary to limit the ripple voltage at the VIN pin while supplying most of the switch current during the on-time. When the buck switch turns on, the current into the VIN pin steps to the lower peak of the inductor current waveform, ramps up to the peak value, then drops to zero at turn-off. The average current into VIN during the on-time is the load current. The input capacitance should be selected for RMS current rating and This procedure provides a guide to select the value of L1. The nearest standard value (100µH) will be used. L1 must be rated for the peak current (IPK+) to prevent saturation. During normal loading conditions, the peak current occurs at maximum load current plus maximum ripple. During an overload condition the peak current is limited to 0.7A nominal (0.85A maximum). 13 www.national.com LM5574/LM5574Q The selected inductor (see Table 1) has a conservative 1.0 Amp saturation current rating. For this manufacturer, the saturation rating is defined as the current necessary for the inductance to reduce by 30%, at 20°C. Application Information LM5574/LM5574Q minimum ripple voltage. A good approximation for the required ripple current rating necessary is IRMS > IOUT / 2. Quality ceramic capacitors with a low ESR should be selected for the input filter. To allow for capacitor tolerances and voltage effects, one 1.0µF, 100V ceramic capacitor will be used. If step input voltage transients are expected near the maximum rating of the LM5574, a careful evaluation of ringing and possible spikes at the device VIN pin should be completed. An additional damping network or input voltage clamp may be required in these cases. R4, C5, C6 These components configure the error amplifier gain characteristics to accomplish a stable overall loop gain. One advantage of current mode control is the ability to close the loop with only two feedback components, R4 and C5. The overall loop gain is the product of the modulator gain and the error amplifier gain. The DC modulator gain of the LM5574 is as follows: C8 The capacitor at the VCC pin provides noise filtering and stability for the VCC regulator. The recommended value of C8 should be no smaller than 0.1µF, and should be a good quality, low ESR, ceramic capacitor. A value of 0.47µF was selected for this design. The dominant low frequency pole of the modulator is determined by the load resistance (RLOAD,) and output capacitance (COUT). The corner frequency of this pole is: DC Gain(MOD) = Gm(MOD) x RLOAD = 0.5 x RLOAD fp(MOD) = 1 / (2π RLOAD COUT) C7 The bootstrap capacitor between the BST and the SW pins supplies the gate current to charge the buck switch gate at turn-on. The recommended value of C7 is 0.022µF, and should be a good quality, low ESR, ceramic capacitor. For RLOAD = 20Ω and COUT = 22µF then fp(MOD) = 362Hz DC Gain(MOD) = 0.5 x 20 = 20dB For the design example of Figure 1 the following modulator gain vs. frequency characteristic was measured as shown in Figure 9. C4 The capacitor at the SS pin determines the soft-start time, i.e. the time for the reference voltage and the output voltage, to reach the final regulated value. The time is determined from: For this application, a C4 value of 0.01µF was chosen which corresponds to a soft-start time of 1ms. R5, R6 R5 and R6 set the output voltage level, the ratio of these resistors is calculated from: R5/R6 = (VOUT / 1.225V) - 1 For a 5V output, the R5/R6 ratio calculates to 3.082. The resistors should be chosen from standard value resistors, a good starting point is selection in the range of 1.0kΩ - 10kΩ. Values of 5.11kΩ for R5, and 1.65kΩ for R6 were selected. 20212015 FIGURE 9. Gain and Phase of Modulator RLOAD = 20 Ohms and COUT = 22µF R1, R2, C2 A voltage divider can be connected to the SD pin to set a minimum operating voltage Vin(min) for the regulator. If this feature is required, the easiest approach to select the divider resistor values is to select a value for R1 (between 10kΩ and 100kΩ recommended) then calculate R2 from: Components R4 and C5 configure the error amplifier as a type II configuration which has a pole at DC and a zero at fZ = 1 / (2πR4C5). The error amplifier zero cancels the modulator pole leaving a single pole response at the crossover frequency of the loop gain. A single pole response at the crossover frequency yields a very stable loop with 90 degrees of phase margin. For the design example, a target loop bandwidth (crossover frequency) of 25kHz was selected. The compensation network zero (fZ) should be selected at least an order of magnitude less than the target crossover frequency. This constrains the product of R4 and C5 for a desired compensation network zero 1 / (2π R4 C5) to be less than 2kHz. Increasing R4, while proportionally decreasing C5, increases the error amp gain. Conversely, decreasing R4 while proportionally increasing C5, decreases the error amp gain. For the design example C5 was selected for 0.022µF and R4 was selected for 24.9kΩ. These values configure the compensation network Capacitor C2 provides filtering for the divider. The voltage at the SD pin should never exceed 8V, when using an external set-point divider it may be necessary to clamp the SD pin at high input voltage conditions. The reference design utilizes the full range of the LM5574 (6V to 75V); therefore these components can be omitted. With the SD pin open circuit the LM5574 responds once the Vcc UVLO threshold is satisfied. www.national.com 14 BIAS POWER DISSIPATION REDUCTION Buck regulators operating with high input voltage can dissipate an appreciable amount of power for the bias of the IC. The VCC regulator must step-down the input voltage VIN to a nominal VCC level of 7V. The large voltage drop across the VCC regulator translates into a large power dissipation within the Vcc regulator. There are several techniques that can significantly reduce this bias regulator power dissipation. Figure 12 and Figure 13 depict two methods to bias the IC from the output voltage. In each case the internal Vcc regulator is used to initially bias the VCC pin. After the output voltage is established, the VCC pin potential is raised above the nominal 7V regulation level, which effectively disables the internal VCC regulator. The voltage applied to the VCC pin should never exceed 14V. The VCC voltage should never be larger than the VIN voltage. 20212016 FIGURE 10. Error Amplifier Gain and Phase The overall loop can be predicted as the sum (in dB) of the modulator gain and the error amp gain. 20212017 FIGURE 11. Overall Loop Gain and Phase 15 www.national.com LM5574/LM5574Q If a network analyzer is available, the modulator gain can be measured and the error amplifier gain can be configured for the desired loop transfer function. If a network analyzer is not available, the error amplifier compensation components can be designed with the guidelines given. Step load transient tests can be performed to verify acceptable performance. The step load goal is minimum overshoot with a damped response. C6 can be added to the compensation network to decrease noise susceptibility of the error amplifier. The value of C6 must be sufficiently small since the addition of this capacitor adds a pole in the error amplifier transfer function. This pole must be well beyond the loop crossover frequency. A good approximation of the location of the pole added by C6 is: fp2 = fz x C5 / C6. zero at 290Hz. The error amp gain at frequencies greater than fZ is: R4 / R5, which is approximately 5 (14dB). LM5574/LM5574Q 20212018 FIGURE 12. VCC Bias from VOUT for 8V < VOUT < 14V 20212019 FIGURE 13. VCC Bias with Additional Winding on the Output Inductor www.national.com 16 17 www.national.com LM5574/LM5574Q the DC resistance of the inductor and the 1.1 factor is an approximation for the AC losses. If a snubber is used, an approximation for the damping resistor power dissipation is P = Vin2 x Fsw x Csnub, where Fsw is the switching frequency and Csnub is the snubber capacitor. The most significant variables that affect the power dissipated by the LM5574 are the output current, input voltage and operating frequency. The power dissipated while operating near the maximum output current and maximum input volatge can be appreciable. The operating frequency of the LM5574 evaluation board has been designed for 300kHz. When operating at 0.5A output current with a 70V input the power dissipation of the LM5574 regulator is approximately 0.6W. The junction-to-ambient thermal resistance of the LM5574 will vary with the application. The most significant variables are the area of copper in the PC board, and the amount of forced air cooling provided. The junction-to-ambient thermal resistance of the LM5574 mounted in the evaluation board varies from 90°C/W with no airflow to 60°C/W with 900 LFM (Linear Feet per Minute). With a 25°C ambient temperature and no airflow, the predicted junction temperature for the LM5574 will be 25 + ((90 x 0.6) = 79°C. If the evaluation board is operated at 0.5A output current, 70V input voltage and high ambient temperature for a prolonged period of time the thermal shutdown protection within the IC may activate. The IC will turn off allowing the junction to cool, followed by restart with the soft-start capacitor reset to zero. PCB LAYOUT AND THERMAL CONSIDERATIONS The circuit in Figure 1 serves as both a block diagram of the LM5574 and a typical application board schematic for the LM5574. In a buck regulator there are two loops where currents are switched very fast. The first loop starts from the input capacitors, to the regulator VIN pin, to the regulator SW pin, to the inductor then out to the load. The second loop starts from the output capacitor ground, to the regulator PGND pins, to the regulator IS pins, to the diode anode, to the inductor and then out to the load. Minimizing the loop area of these two loops reduces the stray inductance and minimizes noise and possible erratic operation. A ground plane in the PC board is recommended as a means to connect the input filter capacitors to the output filter capacitors and the PGND pins of the regulator. Connect all of the low power ground connections (CSS, RT, CRAMP) directly to the regulator AGND pin. Connect the AGND and PGND pins together through the topside copper trace. Place several vias in this trace to the ground plane. The two highest power dissipating components are the recirculating diode and the LM5574 regulator IC. The easiest method to determine the power dissipated within the LM5574 is to measure the total conversion losses (Pin – Pout) then subtract the power losses in the Schottky diode, output inductor and snubber resistor. An approximation for the Schottky diode loss is P = (1-D) x Iout x Vfwd. An approximation for the output inductor power is P = IOUT2 x R x 1.1, where R is LM5574/LM5574Q TABLE 1. 5V, 0.5A Demo Board Bill of Materials Item Part Number Description Value C 1 C3225X7R2A105M CAPACITOR, CER, TDK C 2 OPEN NOT USED 1µ, 100V C 3 C0805A471K1GAC CAPACITOR, CER, KEMET 470p, 100V C 4 C2012X7R2A103K CAPACITOR, CER, TDK 0.01µ, 100V C 5 C2012X7R2A223K CAPACITOR, CER, TDK 0.022µ, 100V C 6 OPEN NOT USED C 7 C2012X7R2A223K CAPACITOR, CER, TDK 0.022µ, 100V C 8 C2012X7R1C474M CAPACITOR, CER, TDK 0.47µ, 16V C 9 C3225X7R1C226M CAPACITOR, CER, TDK 22µ, 16V D 1 CMSH2-100M DIODE, 100V, CENTRAL L 1 DR74-101 INDUCTOR, COOPER R 1 OPEN NOT USED R 2 OPEN NOT USED R 3 CRCW08052102F RESISTOR 21kΩ R 4 CRCW08052492F RESISTOR 24.9kΩ R 5 CRCW08055111F RESISTOR 5.11kΩ R 6 CRCW08051651F RESISTOR 1.65kΩ U 1 LM5574 REGULATOR, NATIONAL SEMICONDUCTOR www.national.com 18 100µH LM5574/LM5574Q PCB Layout 20212029 Component Side 20212030 Solder Side 20212031 Silkscreen 19 www.national.com LM5574/LM5574Q Physical Dimensions inches (millimeters) unless otherwise noted 16-Lead TSSOP Package NS Package Number MTC16 www.national.com 20 LM5574/LM5574Q Notes 21 www.national.com LM5574/LM5574Q SIMPLE SWITCHER® 75V, 0.5A Step-Down Switching Regulator Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage Reference www.national.com/vref Design Made Easy www.national.com/easy PowerWise® Solutions www.national.com/powerwise Solutions www.national.com/solutions Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic Wireless (PLL/VCO) www.national.com/wireless Analog University® www.national.com/AU THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2009 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: [email protected] National Semiconductor Asia Pacific Technical Support Center Email: [email protected] National Semiconductor Japan Technical Support Center Email: [email protected]