TI1 LMV710IDBVR Single low-power rrio operational amplifier Datasheet

Not Recommended for New Designs
LMV710, LMV711, LMV715
SINGLE LOW-POWER RRIO OPERATIONAL AMPLIFIERS
WITH HIGH OUTPUT CURRENT DRIVE AND SHUTDOWN
www.ti.com
SLOS463A – APRIL 2005 – REVISED JULY 2005
FEATURES
•
•
•
•
•
•
•
•
•
2.7-V and 5-V Performance
Low Offset Voltage . . . 0.4 mV Typ, 3 mV Max
Input Common-Mode Range . . . 200 mV
Beyond the Rails
Rail-to-Rail Swing Into 600 Ω
Gain Bandwidth . . . 5 MHz Typ
Slew Rate . . . 5 V/µs Typ
Turn-On Time From Shutdown . . . <10 µs
Shutdown Current . . . 0.2 µA Typ
Space-Saving Packages
– SOT-23-5/6
– SC-70
LMV710
DBV (SOT-23-5) OR DCK (SC-70) PACKAGE
(TOP VIEW)
OUT 1
VCC− 2
+ −
IN+ 3
4 IN−
LMV711/LMV715
DBV (SOT-23-6) OR DCK (SC-70) PACKAGE
(TOP VIEW)
6 VCC+
OUT 1
APPLICATIONS
•
•
•
•
•
•
•
5 VCC+
VCC− 2
Wireless Phones, Mobile Phones, PDAs
GSM/TDMA/CDMA Power Amp Control
AGC, RF Power Detectors
Temperature Compensation
Wireless LANs
Bluetooth
HomeRF
5 SHUTDOWN
+ −
IN+ 3
4 IN−
DESCRIPTION/ORDERING INFORMATION
The LMV710, LMV711, and LMV715 are single BiCMOS operational amplifiers designed to meet the demands of
low power, low cost, and small size required by battery-powered portable electronics. These devices have an
input common-mode voltage range that exceeds the rails, rail-to-rail output, and high output-current drive. The
devices offer a bandwidth of 5 MHz and a slew rate of 5 V/µs.
On the LMV711 and LMV715, a separate shutdown pin can be used to disable the device and reduce the supply
current to 0.2 µA typical. The device features a turn-on time of less than 10 µs. It is an ideal solution for
power-sensitive applications, such as cellular phones, pagers, palm computers, etc.
The LMV710I, LMV711I, and LMV715I are characterized for operation from –40°C to 85°C.
ORDERING INFORMATION
PACKAGE (1)
TA
–40°C to 85°C
(1)
(2)
ORDERABLE PART NUMBER
TOP-SIDE MARKING (2)
SOT-23-5 – DBV
Reel of 3000
LMV710IDBVR
RB4_
SC-70 – DCK
Reel of 3000
LMV710IDCKR
RE_
SOT-23-6 – DBV
Reel of 3000
LMV711IDBVR
RB5_
SC-70 – DCK
Reel of 3000
LMV711IDCKR
RF_
SOT-23-6 – DBV
Reel of 3000
LMV715IDBVR
4B9_
SC-70 – DCK
Reel of 3000
LMV715IDCKR
RL_
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
DBV/DCK: The actual top-side marking has one additional character that designates the assembly/test site.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005, Texas Instruments Incorporated
Not Recommended for New Designs
LMV710, LMV711, LMV715
SINGLE LOW-POWER RRIO OPERATIONAL AMPLIFIERS
WITH HIGH OUTPUT CURRENT DRIVE AND SHUTDOWN
www.ti.com
SLOS463A – APRIL 2005 – REVISED JULY 2005
SYMBOL (EACH AMPLIFIER)
−
IN −
OUT
+
IN +
SIMPLIFIED SCHEMATIC
VCC+
VBIAS1
IP
Class AB
Control
IN+
OUT
IN−
LMV711
only
VBIAS2
IN
VCC−
SD
2
BIAS
Control
Not Recommended for New Designs
LMV710, LMV711, LMV715
SINGLE LOW-POWER RRIO OPERATIONAL AMPLIFIERS
WITH HIGH OUTPUT CURRENT DRIVE AND SHUTDOWN
www.ti.com
SLOS463A – APRIL 2005 – REVISED JULY 2005
Absolute Maximum Ratings
(1)
over operating free-air temperature range (unless otherwise noted)
MIN
VCC+ – VCC–
MAX
Supply voltage (2)
UNIT
6
V
±Supply
voltage
V
VID
Differential input voltage (3)
VI
Input voltage (either input)
VCC– – 0.4
VCC+ + 0.4
V
VO
Output voltage
VCC– – 0.4
VCC+ + 0.4
V
II
Input
±10
current (4)
DBV package
θJA
Package thermal impedance (5) (6)
DCK package
TJ
Operating virtual junction temperature
Tstg
Storage temperature range
(1)
(2)
(3)
(4)
(5)
(6)
5 pin
206
6 pin
165
5 pin
252
6 pin
259
–65
mA
°C/W
150
°C
150
°C
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating
conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values (except differential voltages and VCC specified for the measurement of IOS) are with respect to the network GND.
Differential voltages are at IN+ with respect to IN–.
Excessive input current will flow if a differential input voltage in excess of approximately 0.6 V is applied between the inputs unless some
limiting resistance is used.
Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions
MIN
MAX
UNIT
VCC+ – VCC–
Supply voltage
2.7
5
V
TA
Operating free-air temperature
–40
85
°C
ESD Protection
TYP
UNIT
Human-Body Model
TBD
V
Machine Model
TBD
V
3
Not Recommended for New Designs
LMV710, LMV711, LMV715
SINGLE LOW-POWER RRIO OPERATIONAL AMPLIFIERS
WITH HIGH OUTPUT CURRENT DRIVE AND SHUTDOWN
www.ti.com
SLOS463A – APRIL 2005 – REVISED JULY 2005
Electrical Characteristics
VCC+ = 2.7 V, VCC– = GND, VIC = 1.35 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
IIB
Input bias current
CMRR
Common-mode rejection ratio
kSVR
Supply-voltage rejection ratio
VICR
Common-mode
input voltage range
TEST CONDITIONS
VIC = 0.85 V and 1.85 V
TYP
MAX
0.4
3
3.2
25°C
0 ≤ VIC ≤ 2.7 V
2.7 V ≤ VCC+ ≤ 5 V,
VIC = 0.85 V
2.7 V ≤ VCC+ ≤ 5 V,
VIC = 1.85 V
CMRR ≥ 50 dB
Sinking VO = 5 V
VOH
RL = 10 kΩ to 1.35 V
VOL
Output voltage
VOH
RL = 600 Ω to 1.35 V
VOL
4
25°C
50
–40°C to 85°C
45
25°C
70
–40°C to 85°C
68
25°C
70
–40°C to 85°C
Output short circuit current (1)
VO
MIN
–40°C to 85°C
Sourcing VO = 0
IOS
TA
25°C
UNIT
mV
pA
75
dB
110
dB
95
68
25°C
–0.2
to 2.9
–0.3
to 3
25°C
15
28
–40°C to 85°C
12
25°C
25
–40°C to 85°C
22
25°C
2.62
–40°C to 85°C
2.6
25°C
V
mA
40
2.68
0.01
–40°C to 85°C
0.12
0.15
25°C
2.52
–40°C to 85°C
2.5
25°C
2.55
0.05
–40°C to 85°C
V
0.23
0.3
VO(SD)
Output voltage level in
shutdown mode
LMV711 only
25°C
50
IO(SD)
Output leakage current in
shutdown mode
LMV715 only
25°C
1
pA
CO(SD)
Output capacitance in
shutdown mode
LMV715 only
25°C
32
pF
25°C
1.22
ICC
Supply current
ON mode
Shutdown mode, SHDN = 0
AV
Large-signal voltage gain
–40°C to 85°C
25°C
0.002
25°C
80
–40°C to 85°C
76
Sinking RL = 10 kΩ,
VO = 0.4 V to 1.35 V
25°C
80
–40°C to 85°C
76
25°C
80
–40°C to 85°C
76
25°C
80
–40°C to 85°C
76
Sinking RL = 600 Ω,
VO = 0.5 V to 1.35 V
1.7
1.9
Sourcing RL = 10 kΩ,
VO = 1.35 V to 2.3 V
Sourcing RL = 600 Ω,
VO = 1.35 V to 2.2 V
200
10
mV
mA
µA
115
113
110
dB
100
SR (2)
Slew rate
25°C
5
V/µs
GBWP
Gain bandwidth product
25°C
5
MHz
Φm
Phase margin
25°C
60
deg
T(on)
Amplifier turn-on time
25°C
<10
µs
(1)
(2)
4
Shorting the output to either supply rails will adversely affect reliability.
Number specified is the slower of the positive and negative slew rates.
Not Recommended for New Designs
LMV710, LMV711, LMV715
SINGLE LOW-POWER RRIO OPERATIONAL AMPLIFIERS
WITH HIGH OUTPUT CURRENT DRIVE AND SHUTDOWN
www.ti.com
SLOS463A – APRIL 2005 – REVISED JULY 2005
Electrical Characteristics (continued)
VCC+ = 2.7 V, VCC– = GND, VIC = 1.35 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
V(ON)
SHDN
Shutdown pin voltage range
25°C
MIN
TYP
2.4
to 2.7
1.5
to 2.7
V(OFF)
Vn
Input referred voltage noise
0 to 1
f = 1 kHz
25°C
MAX
0
to 0.8
20
UNIT
V
nV/√Hz
Electrical Characteristics
VCC+ = 3.2 V, VCC– = GND, and VIC = 1.6 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VOH
VO
Output voltage
IO = 6.5 mA
VOL
TA
MIN
TYP
25°C
2.95
3
–40°C to 85°C
2.92
25°C
–40°C to 85°C
0.01
MAX
0.18
UNIT
V
0.25
5
Not Recommended for New Designs
LMV710, LMV711, LMV715
SINGLE LOW-POWER RRIO OPERATIONAL AMPLIFIERS
WITH HIGH OUTPUT CURRENT DRIVE AND SHUTDOWN
www.ti.com
SLOS463A – APRIL 2005 – REVISED JULY 2005
Electrical Characteristics
VCC+ = 5 V, VCC– = GND, VIC = 2.5 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
IIB
Input bias current
CMRR
Common-mode rejection ratio
kSVR
Supply-voltage rejection ratio
VICR
Common-mode
input voltage range
TEST CONDITIONS
VIC = 0.85 V and 1.85 V
TYP
MAX
0.4
3
3.2
25°C
0 ≤ VIC ≤ 2.7 V
2.7 V ≤ VCC+ ≤ 5 V,
VIC = 0.85 V
2.7 V ≤ VCC+ ≤ 5 V,
VIC = 1.85 V
CMRR ≥ 50 dB
Sinking VO = 5 V
VOH
RL = 10 kΩ to 1.35 V
VOL
Output voltage
VOH
RL = 600 Ω to 1.35 V
VOL
4
25°C
50
–40°C to 85°C
48
25°C
70
–40°C to 85°C
68
25°C
70
–40°C to 85°C
Output short circuit current (1)
VO
MIN
–40°C to 85°C
Sourcing VO = 0
IOS
TA
25°C
UNIT
mV
pA
75
dB
110
dB
95
68
25°C
–0.2
to 5.2
–0.3
to 5.3
25°C
25
35
–40°C to 85°C
21
25°C
25
–40°C to 85°C
21
25°C
4.92
–40°C to 85°C
4.9
25°C
V
mA
40
4.98
0.01
–40°C to 85°C
0.12
0.15
25°C
4.82
–40°C to 85°C
4.8
25°C
4.85
0.05
–40°C to 85°C
V
0.23
0.3
VO(SD)
Output voltage level in
shutdown mode
LMV711 only
25°C
50
IO(SD)
Output leakage current in
shutdown mode
LMV715 only
25°C
1
pA
CO(SD)
Output capacitance in
shutdown mode
LMV715 only
25°C
32
pF
25°C
1.17
ICC
Supply current
ON mode
Shutdown mode, SHDN = 0
AV
Large-signal voltage gain
–40°C to 85°C
25°C
0.2
25°C
80
–40°C to 85°C
76
Sinking RL = 10 kΩ,
VO = 0.4 V to 1.35 V
25°C
80
–40°C to 85°C
76
25°C
80
–40°C to 85°C
76
25°C
80
–40°C to 85°C
76
Sinking RL = 600 Ω,
VO = 0.5 V to 1.35 V
1.7
1.9
Sourcing RL = 10 kΩ,
VO = 1.35 V to 2.3 V
Sourcing RL = 600 Ω,
VO = 1.35 V to 2.2 V
200
10
mV
mA
µA
123
120
110
dB
118
SR (2)
Slew rate
25°C
5
V/µs
GBWP
Gain bandwidth product
25°C
5
MHz
Φm
Phase margin
25°C
60
deg
T(on)
Amplifier turn-on time
25°C
<10
µs
(1)
(2)
6
Shorting the output to either supply rails will adversely affect reliability.
Number specified is the slower of the positive and negative slew rates.
Not Recommended for New Designs
LMV710, LMV711, LMV715
SINGLE LOW-POWER RRIO OPERATIONAL AMPLIFIERS
WITH HIGH OUTPUT CURRENT DRIVE AND SHUTDOWN
www.ti.com
SLOS463A – APRIL 2005 – REVISED JULY 2005
Electrical Characteristics (continued)
VCC+ = 5 V, VCC– = GND, VIC = 2.5 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
V(ON)
SHDN
Shutdown pin voltage range
25°C
V(OFF)
Vn
Input referred voltage noise
f = 1 kHz
MIN
TYP
2.4
to 5
2 to 5
0 to 1.5
25°C
20
MAX
0
to 0.8
UNIT
V
nV/√Hz
7
Not Recommended for New Designs
LMV710, LMV711, LMV715
SINGLE LOW-POWER RRIO OPERATIONAL AMPLIFIERS
WITH HIGH OUTPUT CURRENT DRIVE AND SHUTDOWN
SLOS463A – APRIL 2005 – REVISED JULY 2005
TYPICAL PERFORMANCE CHARACTERISTICS
GRAPH PREVIEWS
Figure 1. Supply Current vs Supply Voltage (ON Mode)
Figure 2. LMV711/LMV715 Supply Current vs Supply Voltage (Shutdown Mode)
Figure 3. Output Positive Swing vs Supply Voltage RL = 600 Ω)
Figure 4. Output Negative Swing vs Supply Voltage RL = 600 Ω)
Figure 5. Output Positive Swing vs Supply Voltage RL = 10 kΩ)
Figure 6. Output Negative Swing vs Supply Voltage RL = 10 kΩ)
Figure 7. Output Positive Swing vs Supply Voltage (ISRC = 7 mA)
Figure 8. Output Negative Swing vs Supply Voltage (ISINK = 7 mA)
Figure 9. Input Voltage Noise vs Frequency
Figure 10. PSRR vs Frequency
Figure 11. CMRR vs Frequency
Figure 12. LMV711/LMV715 Turn-On Characteristics
Figure 13. Sourcing Current vs Output Voltage
Figure 14. Sinking Current vs Output Voltage
Figure 15. THD+N vs Frequency (VCC = 5 V)
Figure 16. THD+N vs Frequency (VCC = 2.7 V)
Figure 17. THD+N vs VOUT (VCC± = ±2.5 V)
Figure 18. THD+N vs VOUT (VCC± = ±1.35 V)
Figure 19. CCM vs VCM (VCC = 2.7 V)
Figure 20. CCM vs VCM (VCC = 5 V)
Figure 21. CDIFF vs VCM (VCC = 2.7 V)
Figure 22. CDIFF vs VCM (VCC = 5 V)
Figure 23. Open-Loop Frequency Response (VCC± = ±1.35 V)
Figure 24. Open-Loop Frequency Response (VCC± = ±1.6 V)
Figure 25. Open-Loop Frequency Response (VCC± = ±2.5 V)
Figure 26. Open-Loop Frequency Response (VCC± = ±1.35 V)
Figure 27. Open-Loop Frequency Response (VCC± = ±1.6 V)
Figure 28. Open-Loop Frequency Response (VCC± = ±2.5 V)
Figure 29. Noninverting Large Signal Pulse Response
Figure 30. Noninverting Small Signal Pulse Response Figure
Figure 31. Inverting Large Signal Pulse Response
Figure 32. Inverting Small Signal Pulse Response
Figure 33. VOS vs VCM (VCC = 2.7 V)
Figure 34. VOS vs VCM (VCC = 5 V)
8
www.ti.com
PACKAGE OPTION ADDENDUM
www.ti.com
12-May-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LMV710IDBVR
OBSOLETE
SOT-23
DBV
5
TBD
Call TI
Call TI
-40 to 85
LMV710IDBVRE4
OBSOLETE
SOT-23
DBV
5
TBD
Call TI
Call TI
-40 to 85
LMV710IDBVRG4
OBSOLETE
SOT-23
DBV
5
TBD
Call TI
Call TI
-40 to 85
LMV710IDCKR
OBSOLETE
SC70
DCK
5
TBD
Call TI
Call TI
-40 to 85
LMV710IDCKRE4
OBSOLETE
SC70
DCK
5
TBD
Call TI
Call TI
-40 to 85
LMV710IDCKRG4
OBSOLETE
SC70
DCK
5
TBD
Call TI
Call TI
-40 to 85
LMV711IDBVR
OBSOLETE
SOT-23
DBV
6
TBD
Call TI
Call TI
-40 to 85
LMV711IDBVRE4
OBSOLETE
SOT-23
DBV
6
TBD
Call TI
Call TI
-40 to 85
LMV711IDBVRG4
OBSOLETE
SOT-23
DBV
6
TBD
Call TI
Call TI
-40 to 85
LMV711IDCKR
OBSOLETE
SC70
DCK
6
TBD
Call TI
Call TI
-40 to 85
LMV711IDCKRE4
OBSOLETE
SC70
DCK
6
TBD
Call TI
Call TI
-40 to 85
LMV711IDCKRG4
OBSOLETE
SC70
DCK
6
TBD
Call TI
Call TI
-40 to 85
LMV715IDBVR
OBSOLETE
SOT-23
DBV
6
TBD
Call TI
Call TI
-40 to 85
LMV715IDBVRE4
OBSOLETE
SOT-23
DBV
6
TBD
Call TI
Call TI
-40 to 85
LMV715IDBVRG4
OBSOLETE
SOT-23
DBV
6
TBD
Call TI
Call TI
-40 to 85
LMV715IDCKR
OBSOLETE
SC70
DCK
6
TBD
Call TI
Call TI
-40 to 85
LMV715IDCKRE4
OBSOLETE
SC70
DCK
6
TBD
Call TI
Call TI
-40 to 85
LMV715IDCKRG4
OBSOLETE
SC70
DCK
6
TBD
Call TI
Call TI
-40 to 85
RB4B
REB
RB5B
RFB
RB9B
RLB
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
12-May-2014
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
Similar pages