ETC1 LP1020-22 Switch-mode led driver Datasheet

Product
Specifications
LED Driver
LP1020-xx Series
Switch-Mode LED Driver
Total Power
20 Watts
Input Voltages
100 ~ 277 VAC
Number of Outputs One
ANZ#: Z095G, February 24, 2010
SPECIAL FEATURES
ELECTRICAL SPECIFICATIONS
• UL1310, Class 2 and UL879 recognized
• Single output, constant current or constant
voltage design
• IP66 compliant
• Suitable for dry and damp locations
• Designed for outdoor or indoor applications
• Suitable in standard electrical junction boxes
• Compact and lightweight
• Active PFC reduces power consumption
ENVIRONMENTAL
Input range
Frequency
Power Factor
Crest Factor
Inrush current
Input current
Efficiency
EMI filtering
Maximum power
Current Accuracy
Load regulation
Leakage Current
Hold up time
Operating temperature:
-30 to 60 º C
(De-rating : 1% per º C from 60~70ºC )
Protection
Storage temperature:
-40 to +85º C
Humidity (Non-Condensing): 5% to 95%
Cooling:
Convection
SAFETY
Vibration Frequency:
5 to 50 Hz
UL
MTBF:
>100,000 Hours at full load and 25ºC cUL
ambient conditions (MIL-217F)
CE
EMC :
Compliant to 47CFR, Part 2, Part15 and
Cispr PUB, 22 Class B
Model Number
LP1020-52
LP1020-36
LP1020-24
LP1020-22
LP1020-18
LP1020-17
LP1020-15
LP1020-13
LP1020-12
LP1020-10
Constant Voltage Mode
Output
V (DC)
A (mA)
Watts
52, ±5%
400
20
36, ±5%
550
20
24, ±5%
830
20
22, ±5%
910
20
18, ±5%
1100
20
17, ±5%
1250
20
15, ±5%
1330
20
13, ±5%
1540
20
12, ±5%
1660
20
10, ±5%
2000
20
100 ~ 304 VAC
47 to 63 Hz
> 0.92 at full load, 115VAC
1.5 max.
10.0 Amps maximum at 230VAC, cold start, 25º C
0.3 Amps maximum at 115VAC
85% typical at maximum load
47CFR, Part 2, Part 15 and Cispr PUB, 22 Class B
20W
±1% (when applicable)
±3%
300uA typ.
Half cycle minimum at 120 VAC and 80% of rated
load
Over-voltage, Over current and Short circuit
protection: Auto-recovery
UL1310, Class 2 and UL879 recognized
UL1310, Class 2 and UL879 recognized
Note: 52VDC output is not cUL recognized
Constant Current Mode
Output
V (DC)
mA(Max.)
Watts
24~ 52
400, ±5%
20
LP1020-52-Cxxxx
18~ 36
550, ±5%
20
LP1020-36-Cxxxx
12~ 24
830, ±5%
20
LP1020-24-Cxxxx
12 ~ 22
910, ±5%
20
LP1020-22-Cxxxx
9 ~ 18
1100, ±5%
20
LP1020-18-Cxxxx
9 ~ 17
1250, ±5%
20
LP1020-17-Cxxxx
9 ~ 15
1330, ±5%
20
LP1020-15-Cxxxx
7 ~ 13
1540, ±5%
20
LP1020-13-Cxxxx
7 ~ 12
1660, ±5%
20
LP1020-12-Cxxxx
7 ~ 10
2000, ±5%
20
LP1020-10-Cxxxx
Note: The output current of Constant Current models are
adjustable at factory from 50% ~ 100%.
Model Number
RECOMMEND APPLICATION SCHEMATICS
R
20W, 24VDC
LP1020
R
20W, 24VDC
LP1020-CC
This configuration is based on LED with the following parameters:
VF: 3.0V ~ 3.5V
IF: 300mA ~ 350mA A. IF: 300mA ~ 350mA
Recommended value for R is 20 ohm, 3W
INDUSTRIES CORP. 5625-A S. Arville, Las Vegas, NV 89118 Tel:702-364-9998 Fax: 702-364-1562 www.magtechind.com Anz095G
MECHANICAL DRAWING
Model Information – Single DC output
LP1020-XX – Constant Voltage Model
XX – Available Output Voltage, refer to chart above
LP1020-XXC (YYY) – Constant Current Model
C – Stands for Constant Current Model
XX – Available Output Voltage
YYY – Available Constant Current Settings, 350mA or 700mA or 1050mA
AC input cable
AWG #20, two conductors UL PLTC type or equiv.
DC output cable
AWG #20, two conductors UL PLTC type or equiv.
10 [0.39]
(2X)
4 [0.16]
(2X)
LP1020
95 [3.74]
25 [0.98]
10 [0.39]
(2X)
40 [1.57]
5 [0.20]
(2X)
DC OUTPUT
WIRES
3.6 [0.14]
(2X)
AC INPUT WIRES
5 [0.20]
(2X)
INDUSTRIES CORP. 5625-A S. Arville, Las Vegas, NV 89118 Tel:702-364-9998 Fax: 702-364-1562 www.magtechind.com Anz095G
Similar pages