Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type) Data Sheet 1 Chip Inductor (Chip Coil) Power Inductor (Wire Wound Type) LQH2HP_G0 Series (1008 Size) c Dimensions c Packaging Code Packaging Minimum Quantity L 180mm Embossed Tape 3000 0.9±0.1 Polarity Marking 2.5±0.2 0.85±0.3 2.0±0.2 0.85±0.3 (in mm) c Rated Value (p: packaging code) Inductance Rated Current (Based on Inductance Change) Rated Current (Based on Temperature Rise) DC Resistance Self Resonance Frequency (min.) LQH2HPN2R2MG0p 2.2µH ±20% 1640mA 1000mA 0.17ohm ±20% 80MHz LQH2HPN3R3MG0p 3.3µH ±20% 1290mA 810mA 0.27ohm ±20% 65MHz LQH2HPN4R7MG0p 4.7µH ±20% 1000mA 700mA 0.36ohm ±20% 60MHz LQH2HPN6R8MG0p 6.8µH ±20% 800mA 590mA 0.5ohm ±20% 10MHz LQH2HPN100MG0p 10µH ±20% 700mA 490mA 0.73ohm ±20% 10MHz Part Number LQH2HPN220MG0p 22µH ±20% 490mA 340mA 1.6ohm ±20% 10MHz LQH2HPN101MG0p 100µH ±20% 210mA 130mA 10ohm ±20% 5MHz Test Frequency: 1MHz Class of Magnetic Shield: Magnetic shield of magnetic powder in resin Operating Temperature Range (Self-temperature rise is not included): -40 to +85°C Only for reflow soldering. c Notice (Rated Current) Inductance will be more than the value which is 30% down from minimum rated Inductance value. When Rated Current is applied to the Products, self-generation of heat will rise to 40°C or less. Continued on the following page. oThis data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2012.5.10 http://www.murata.com/ Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type) Data Sheet 2 Continued from the preceding page. c Inductance-Frequency Characteristics (Typ.) c Inductance-Current Characteristics (Typ.) 1000 1000 100μH 100 100 100μH 10μH Inductance (μH) Inductance (μH) 22μH 10μH 6.8μH 4.7μH 3.3μH 2.2μH 10 6.8μH 22μH 4.7μH 10 3.3μH 2.2μH 1 1 0.1 0.1 1 10 Frequency (MHz) 100 0.1 10 1000 100 1000 10000 Current (mA) c Temperature Rise Characteristics (Typ.) 50 10μH 4.7μH 3.3μH 2.2μH 100μH Temperature Rise (°C) 40 6.8μH 22μH 30 20 10 0 0 350 700 Current (mA) 1050 1400 c !Caution/Notice !Caution (Rating) Do not use products beyond the rated current as this may create excessive heat. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. oThis data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2012.5.10 http://www.murata.com/