LINER LT1964ES5-SDTRPBF 200ma, low noise,low dropout negative micropower regulator Datasheet

LT1964
200mA, Low Noise,
Low Dropout Negative
Micropower Regulator
FEATURES
DESCRIPTION
n
The LT®1964 is a micropower low noise, low dropout negative regulator. The device is capable of supplying 200mA
of output current with a dropout voltage of 340mV. Low
quiescent current (30μA operating and 3μA shutdown)
makes the LT1964 an excellent choice for battery-powered applications. Quiescent current is well controlled in
dropout.
n
n
n
n
n
n
n
n
n
n
n
Low Noise: 30μVRMS (10Hz to 100kHz)
Low Quiescent Current: 30μA
Low Dropout Voltage: 340mV
Output Current: 200mA
Fixed Output Voltage: –5V
Adjustable Output from –1.22V to – 20V
Positive or Negative Shutdown Logic
3μA Quiescent Current in Shutdown
Stable with 1μF Output Capacitor
Stable with Aluminum, Tantalum, or Ceramic
Capacitors
Thermal Limiting
Low Proﬁle (1mm) ThinSOT™ and (0.75mm) 8-Pin
3mm × 3mm DFN Packages
APPLICATIONS
n
n
n
Battery-Powered Instruments
Low Noise Regulator for Noise-Sensitive
Instrumentation
Negative Complement to LT1761 Family of
Positive LDOs
Other features of the LT1964 include low output noise.
With the addition of an external 0.01μF bypass capacitor,
output noise is reduced to 30μVRMS over a 10Hz to 100kHz
bandwidth. The LT1964 is capable of operating with small
capacitors and is stable with output capacitors as low
as 1μF. Small ceramic capacitors can be used without
the necessary addition of ESR as is common with other
regulators. Internal protection circuitry includes reverse
output protection, current limiting, and thermal limiting.
The device is available with a ﬁxed output voltage of –5V
and as an adjustable device with a –1.22V reference voltage. The LT1964 regulators are available in a low proﬁle
(1mm) ThinSOT and the low proﬁle (0.75mm) 8-pin
(3mm × 3mm) DFN packages.
L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. ThinSOT is
a trademark of Linear Technology Corporation. All other trademarks are the property of their
respective owners.
TYPICAL APPLICATION
10Hz to 100kHz Output Noise
–5V Low Noise Regulator
1μF
VIN
–5.4V
TO –20V
10μF
GND
SHDN
LT1964-5
IN
VOUT
100μV/DIV
BYP
30μVRMS
0.01μF
OUT
–5V AT 200mA
30μVRMS NOISE
1964 TA01a
1ms/DIV
1964 TA01b
1964fb
1
LT1964
ABSOLUTE MAXIMUM RATINGS
(Note 1)
IN Pin Voltage ........................................................ ±20V
OUT Pin Voltage (Note 11) ......................................±20V
OUT to IN Differential Voltage (Note 11) ........ –0.5V, 20V
ADJ Pin Voltage
(with Respect to IN Pin) (Note 11)............. –0.5V, 20V
BYP Pin Voltage
(with Respect to IN Pin)..................................... ±20V
SHDN Pin Voltage
(with Respect to IN Pin) (Note 11)............. –0.5V, 35V
SHDN Pin Voltage
(with Respect to GND Pin) ..........................–20V, 15V
Output Short-Circuit Duration .......................... Indeﬁnite
Operating Junction Temperature (E, I Grade)
Range (Note 10) ............................... – 40°C to 125°C
Storage Temperature Range................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec)
SOT-23 Package................................................ 300°C
PIN CONFIGURATION
LT1964
LT1964-SD
TOP VIEW
TOP VIEW
OUT
1
OUT
2
ADJ
3
SHDN
4
8 IN
9
5 OUT
GND 1
7 IN
IN 2
6 GND
SHDN 3
4 ADJ
5 BYP
S5 PACKAGE
5-LEAD PLASTIC SOT-23
TJMAX = 150°C, θJA ≈125°C/W to 250°C/W
(NOTE 13)
SEE THE APPLICATIONS INFORMATION SECTION
DD PACKAGE
8-LEAD (3mm s 3mm) PLASTIC DFN
TJMAX = 125°C, θJA = 40°C/W, θJC = 16°C/W
(NOTE 13)
EXPOSED PAD (PIN 9) IS IN, MUST BE SOLDERED TO PCB
LT1964-BYP
LT1964-5
TOP VIEW
GND 1
TOP VIEW
5 OUT
GND 1
IN 2
BYP 3
5 OUT
IN 2
BYP 3
4 ADJ
S5 PACKAGE
5-LEAD PLASTIC SOT-23
TJMAX = 150°C, θJA ≈125°C/W to 250°C/W
(NOTE 13)
SEE THE APPLICATIONS INFORMATION SECTION
4 SHDN
S5 PACKAGE
5-LEAD PLASTIC SOT-23
TJMAX = 150°C, θJA ≈125°C/W to 250°C/W
(NOTE 13)
SEE THE APPLICATIONS INFORMATION SECTION
ORDER INFORMATION
LEAD FREE FINISH
LT1964ES5-SD#PBF
LT1964ES5-BYP#PBF
LT1964ES5-5#PBF
LT1964EDD#PBF
TAPE AND REEL
LT1964ES5-SD#TRPBF
LT1964ES5-BYP#TRPBF
LT1964ES5-5#TRPBF
LT1964EDD#TRPBF
PART MARKING*
LTVX
LTVY
LTVZ
LDVM
LT1964IS5-SD#PBF
LT1964IS5-BYP#PBF
LT1964IS5-5#PBF
LT1964IDD#PBF
LT1964IS5-SD#TRPBF
LT1964IS5-BYP#TRPBF
LT1964IS5-5#TRPBF
LT1964IDD#TRPBF
LTVX
LTVY
LTVZ
LDVM
PACKAGE DESCRIPTION
5-Lead Plastic SOT-23
5-Lead Plastic SOT-23
5-Lead Plastic SOT-23
8-Lead (3mm × 3mm) Plastic DFN
5-Lead Plastic SOT-23
5-Lead Plastic SOT-23
5-Lead Plastic SOT-23
8-Lead (3mm × 3mm) Plastic DFN
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
1964fb
2
LT1964
ORDER INFORMATION
LEAD BASED FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT1964ES5-SD
LT1964ES5-SD#TR
LTVX
5-Lead Plastic SOT-23
–40°C to 125°C
LT1964ES5-BYP
LT1964ES5-BYP#TR
LTVY
5-Lead Plastic SOT-23
–40°C to 125°C
LT1964ES5-5
LT1964ES5-5#TR
LTVZ
5-Lead Plastic SOT-23
–40°C to 125°C
LT1964EDD
LT1964EDD#TR
LDVM
8-Lead (3mm × 3mm) Plastic DFN
–40°C to 125°C
LT1964IS5-SD
LT1964IS5-SD#TR
LTVX
5-Lead Plastic SOT-23
–40°C to 125°C
LT1964IS5-BYP
LT1964IS5-BYP#TR
LTVY
5-Lead Plastic SOT-23
–40°C to 125°C
LT1964IS5-5
LT1964IS5-5#TR
LTVZ
5-Lead Plastic SOT-23
–40°C to 125°C
LT1964IDD
LT1964IDD#TR
LDVM
8-Lead (3mm × 3mm) Plastic DFN
–40°C to 125°C
Consult LTC Marketing for parts speciﬁed with wider operating temperature ranges. *The temperature grade is identiﬁed by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel speciﬁcations, go to: http://www.linear.com/tapeandreel/
ELECTRICAL CHARACTERISTICS
The l denotes the speciﬁcations which apply over the full operating
temperature range, otherwise speciﬁcations are at TA = 25°C.
PARAMETER
CONDITIONS
Regulated Output Voltage
(Notes 3, 9)
LT1964-5
VIN = –5.5V, ILOAD = –1mA
–20V < VIN < –6V, –200mA < ILOAD < –1mA
ADJ Pin Voltage
(Notes 2, 3, 9)
LT1964
Line Regulation
Load Regulation
Dropout Voltage
VIN = VOUT(NOMINAL)
(Notes 4, 5)
GND Pin Current
VIN = VOUT(NOMINAL)
(Notes 4, 6)
MIN
TYP
MAX
l
–4.925
–4.850
–5
–5
–5.075
–5.150
V
V
VIN = –2V, ILOAD = –1mA
–20V < VIN < –2.8V, –200mA < ILOAD < –1mA
l
–1.202
–1.184
–1.22
–1.22
–1.238
–1.256
V
V
LT1964-5
LT1964 (Note 2)
ΔVIN = –5.5V to –20V, ILOAD = –1mA
ΔVIN = –2.8V to –20V, ILOAD = –1mA
l
l
15
1
50
12
mV
mV
LT1964-5
VIN = –6V, ΔILOAD = –1mA to –200mA
VIN = –6V, ΔILOAD = –1mA to –200mA
l
15
35
50
mV
mV
LT1964
VIN = –2.8V, ΔILOAD = –1mA to –200mA
VIN = –2.8V, ΔILOAD = –1mA to –200mA
l
2
7
15
mV
mV
0.1
0.15
0.19
V
V
0.15
0.20
0.25
V
V
0.26
0.33
0.39
V
V
0.34
0.42
0.49
V
V
30
85
300
1.3
2.5
70
180
600
3
6
μA
μA
μA
mA
mA
ILOAD = –1mA
ILOAD = –1mA
l
ILOAD = –10mA
ILOAD = –10mA
l
ILOAD = –100mA
ILOAD = –100mA
l
ILOAD = –200mA
ILOAD = –200mA
l
ILOAD = 0mA
ILOAD = –1mA
ILOAD = –10mA
ILOAD = –100mA
ILOAD = –200mA
l
l
l
l
l
UNITS
1964fb
3
LT1964
ELECTRICAL CHARACTERISTICS
The l denotes the speciﬁcations which apply over the full operating
temperature range, otherwise speciﬁcations are at TA = 25°C.
Output Voltage Noise
COUT = 10μF, CBYP = 0.01μF, ILOAD = –200mA, BW = 10Hz to 100kHz
30
ADJ Pin Bias Current
(Notes 2, 7)
30
100
nA
Minimum Input Voltage (Note 12)
ILOAD = –200mA
LT1964-BYP
LT1964-SD
l
l
–1.9
–1.6
–2.8
–2.2
V
V
Shutdown Threshold
VOUT = Off to On (Positive)
VOUT = Off to On (Negative)
VOUT = On to Off (Positive)
VOUT = On to Off (Negative)
l
l
l
l
1.6
–1.9
0.8
–0.8
2.1
–2.8
V
V
V
V
–1
±0.1
6
–3
1
15
–9
μA
μA
μA
3
10
μA
46
54
dB
350
mA
mA
SHDN Pin Current (Note 8)
VSHDN = 0V
VSHDN = 15V
VSHDN = –15V
l
Quiescent Current in Shutdown
VIN = –6V, VSHDN = 0V
Ripple Rejection
VIN – VOUT = –1.5V(Avg), VRIPPLE = 0.5VP-P,
fRIPPLE = 120Hz, ILOAD = –200mA
Current Limit
VIN = –6V, VOUT = 0V
VIN = VOUT(NOMINAL) –1.5V, ΔVOUT = 0.1V
l
VIN = 20V, VOUT, VADJ, VSHDN = Open Circuit
l
Input Reverse Leakage Current
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime
Note 2: The LT1964 (adjustable version) is tested and speciﬁed for these
conditions with the ADJ pin connected to the OUT pin.
Note 3: Operating conditions are limited by maximum junction
temperature. The regulated output voltage speciﬁcation will not apply
for all possible combinations of input voltage and output current. When
operating at maximum input voltage, the output current range must be
limited. When operating at maximum output current, the input voltage
range must be limited.
Note 4: To satisfy requirements for minimum input voltage, the LT1964
(adjustable version) is tested and speciﬁed for these conditions with an
external resistor divider (two 249k resistors) for an output voltage of
–2.44V. The external resistor divider will add a 5μA DC load on the output.
Note 5: Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a speciﬁed output current. In dropout, the
output voltage will be equal to: (VIN + VDROPOUT).
Note 6: GND pin current is tested with VIN = VOUT(NOMINAL) and a current
source load. This means the device is tested while operating in its dropout
region. This is the worst-case GND pin current. The GND pin current will
decrease slightly at higher input voltages.
0.25
–0.25
μVRMS
220
1
mA
Note 7: ADJ pin bias current ﬂows out of the ADJ pin.
Note 8: Positive SHDN pin current ﬂows into the SHDN pin. SHDN pin
current is included in the GND pin current speciﬁcation.
Note 9: For input-to-output differential voltages greater than 7V, a 50μA
load is needed to maintain regulation.
Note 10: The LT1964 is tested and speciﬁed under pulse load conditions
such that TJ ≅ TA. The LT1964E is tested at TA = 25°C. Performance at
–40°C to 125°C is assured by design, characterization and correlation with
statistical process controls. The LT1964I is guaranteed over the full –40°C
to 125°C operating junction temperature range.
Note 11: A parasitic diode exists internally on the LT1964 between the
OUT, ADJ and SHDN pins and the IN pin. The OUT, ADJ and SHDN pins
cannot be pulled more than 0.5V more negative than the IN pin during
fault conditions, and must remain at a voltage more positive than the IN
pin during operation.
Note 12: For the LT1964-BYP, this speciﬁcation accounts for the operating
threshold of the SHDN pin, which is tied to the IN pin internally. For the
LT1964-SD, the SHDN threshold must be met to ensure device operation.
Note 13: Actual thermal resistance (θJA) junction to ambient will be a
function of board layout. See the Thermal Considerations section in the
Applications Information.
1964fb
4
LT1964
TYPICAL PERFORMANCE CHARACTERISTICS
Guaranteed Dropout Voltage
450
450
400
TJ = 125°C
350
300
250
TJ = 25°C
200
150
Dropout Voltage
500
= TEST POINT
450
400
TJ ≤ 125°C
DROPOUT VOLTAGE (mV)
500
DROPOUT VOLTAGE (mV)
DROPOUT VOLTAGE (mV)
Typical Dropout Voltage
500
350
300
250
TJ ≤ 25°C
200
150
350
250
IL = –100mA
200
IL = –50mA
150
100
100
50
50
50
0
0
–40
–80
–120
–160
OUTPUT CURRENT (mA)
–200
0
–40
–80
–120
–160
OUTPUT CURRENT (mA)
–50
VIN = –6V
RL = 250k (∞ FOR LT1964-5)
IL = –5μA (0 FOR LT1964-5)
–20
–15
–10
VSHDN = 0V
–5
0
–50
–25
0
25
50
75
TEMPERATURE (°C)
IL = –1mA
100
125
125
–5.06
–5.03
–5.00
–4.97
–1.230
–1.225
–1.220
–1.215
–4.94
–1.210
–4.91
–1.205
–4.88
–50
–25
IL = –1mA
–1.235
ADJ PIN VOLTAGE (V)
OUTPUT VOLTAGE (V)
–25
100
–1.240
–5.09
VSHDN = VIN
0
25
50
75
TEMPERATURE (°C)
LT1964 ADJ Pin Voltage
–5.12
–30
–25
1964 G03
LT1964-5
Output Voltage
–35
IL = –1mA
1964 G02
Quiescent Current
–40
IL = –10mA
0
–50
–200
1964 G01
–45
IL = –200mA
300
100
0
QUIESCENT CURRENT (μA)
400
0
25
50
75
TEMPERATURE (°C)
100
125
–1.200
–50
–25
0
25
50
75
TEMPERATURE (°C)
1964 G05
100
125
1964 G06
1964 G04
LT1964-5
Quiescent Current
–40
QUIESCENT CURRENT (μA)
–35
VSHDN = VIN
–30
–25
–20
–15
–10
VSHDN = 0V
–5
0
–3.0
TJ = 25°C
RL = 250k
IL = –5μA
–35
QUIESCENT CURRENT (μA)
TJ = 25°C
RL = ∞
–30
–25
–20
–15
–10
–0
0
TJ = 25°C
VSHDN = VIN
*FOR VOUT = –5V
–2.5
–2.0
–1 –2 –3 –4 –5 –6 –7 –8 –9 –10
INPUT VOLTAGE (V)
–1.5
RL = 100
IL = –50mA*
–1.0
1964 G08
0
RL = 25
IL = –200mA*
RL = 50
IL = –100mA*
RL = 500
IL = –10mA*
–0.5
VSHDN = 0V
–5
–1 –2 –3 –4 –5 –6 –7 –8 –9 –10
INPUT VOLTAGE (V)
VSHDN = VIN
GND PIN CURRENT (mA)
–40
–0
LT1964-5
GND Pin Current
LT1964 Quiescent Current
0
–1 –2 –3 –4 –5 –6 –7 –8 –9 –10
INPUT VOLTAGE (V)
1964 G09
1964 G07
1964fb
5
LT1964
TYPICAL PERFORMANCE CHARACTERISTICS
LT1964 GND Pin Current
TJ = 25°C; VSHDN = VIN; *FOR VOUT = –1.22V
VIN = VOUT(NOMINAL) – 1V
2.0
–2.0
RL = 12.2Ω
IL = –100mA*
–1.5
–1.0
RL = 24.4Ω
IL = –50mA*
–0.5
RL = 122Ω
IL = –10mA*
0
–2.5
TJ = 25°C
–2.0
TJ = 125°C
–1.5
–1.0
0
SHDN Pin Input Current
0
–40
–80
–120
–160
OUTPUT CURRENT (mA)
SHDN PIN INPUT CURRENT (μA)
SHDN PIN INPUT CURRENT (μA)
–1.0
4
2
0
–2
–4
–6
–8
8
10
1964 G13
ON
–25
0
25
50
75
TEMPERATURE (°C)
125
ADJ Pin Bias Current
–70
VIN = –15V
POSITIVE CURRENT
FLOWS INTO THE PIN
9
–60
6
VSHDN = 15V
3
0
VSHDN = –15V
–3
–6
–9
–50
100
1964 G12
SHDN Pin Input Current
TJ = 25°C
POSITIVE CURRENT
FLOWS INTO THE PIN
OFF
–0.5
–2.5
–50
–200
12
–10
–10 –8 –6 –4 –2 0 2 4 6
SHDN PIN VOLTAGE (V)
0
1964 G11
10
6
0.5
–2.0
1964 G10
8
1.0
–1.5
–0.5
–1 –2 –3 –4 –5 –6 –7 –8 –9 –10
INPUT VOLTAGE (V)
ON
1.5
TJ = –50°C
–3.0
SHDN PIN VOLTAGE (V)
RL = 6.1Ω
IL = –200mA*
ADJ PIN BIAS CURRENT (nA)
GND PIN CURRENT (mA)
2.5
–3.5
–2.5
0
SHDN Pin Thresholds
GND Pin Current vs ILOAD
–4.0
GND PIN CURRENT (mA)
–3.0
–50
–40
–30
–20
–10
–25
0
25
50
75
TEMPERATURE (°C)
100
125
1964 G14
0
–50
–25
0
25
50
75
TEMPERATURE (°C)
100
125
1964 G15
1964fb
6
LT1964
TYPICAL PERFORMANCE CHARACTERISTICS
Current Limit
Current Limit
–600
ΔVOUT = 100mV
VIN = –7V
VOUT = 0V
–400
–300
–200
–100
–400
–300
–200
–100
–4
–8
–12
–16
INPUT/OUTPUT DIFFERENTIAL (V)
0
–50
–20
–25
0
25
50
75
TEMPERATURE (°C)
1964 G16
MINIMUM INPUT VOLTAGE (V)
RIPPLE REJECTION (dB)
VIN = VOUT(NOMINAL) – 1V +
0.5VP-P RIPPLE AT f = 120Hz
IL = –200mA
54
52
50
48
46
44
–50
–25
0
25
50
75
TEMPERATURE (°C)
40
100
125
1964 G19
COUT = 10μF
30
20
100
0
125
LT1964-BYP
Minimum Input Voltage
60
56
50
COUT = 1μF
10
100
1k
10k
FREQUENCY (Hz)
100k
LT1964, LT1964-SD
Minimum Input Voltage
–3.0
–3.0
–2.5
–2.5
–2.0
IL = –200mA
–1.5
IL = –1mA
–1.0
–0.5
0
–50
NOTE: THE MINIMUM INPUT VOLTAGE
ACCOUNTS FOR THE OPERATING
THRESHOLD OF THE SHDN PIN WHICH
IS TIED TO THE IN PIN INTERNALLY
–25
1M
1964 G18
1964 G17
Input Ripple Rejection
58
60
10
0
25
50
75
TEMPERATURE (°C)
100
125
1964 G20
MINIMUM INPUT VOLTAGE (V)
0
IL = –200mA
VIN = VOUT(NOMINAL) – 1V +
50mVRMS RIPPLE
CBYP = 0
70
RIPPLE REJECTION (dB)
–500
CURRENT LIMIT (mA)
CURRENT LIMIT (mA)
–500
0
Input Ripple Rejection
80
–600
–2.0
IL = –200mA
–1.5
IL = –1mA
–1.0
–0.5
0
–50
NOTE: THE SHDN PIN THRESHOLD
MUST BE MET TO ENSURE
DEVICE OPERATION
–25
0
25
50
75
TEMPERATURE (°C)
100
125
1964 G21
1964fb
7
LT1964
TYPICAL PERFORMANCE CHARACTERISTICS
Load Regulation
IL = –1mA TO –200mA
LOAD REGULATION (mV)
25
LT1964-5
15
10
5
LT1964
0
–50
–25
0
25
50
75
TEMPERATURE (°C)
100
125
140
10
120
CBYP = 1000pF CBYP = 100pF
1
CBYP = 0
0.1
CBYP = 0.01μF
OUTPUT NOISE (μVRMS)
OUTPUT NOISE SPECTRAL DENSITY (μV/√Hz)
30
20
RMS Output Noise vs Bypass
Capacitor
Output Noise Spectral Density
LT1964-5
COUT = 10μF
IL = –200mA
f = 10Hz TO 100kHz
100
80
60
40
LT1964
COUT = 10μF
IL = 200mA
LT1964-5
LT1964
0
0.01
10
100
1k
10k
FREQUENCY (Hz)
1964 G22
RMS Output Noise vs Load
Current
20
10
100k
100
1k
10k
CBYP (pF)
1964 G23
1964 G24
LT1964-5, 10Hz to 100kHz Output
Noise, CBYP = 0
LT1964-5, 10Hz to 100kHz Output
Noise, CBYP = 100pF
140
COUT = 10μF
LT1964-5
OUTPUT NOISE (μVRMS)
120
100
VOUT
200μV/DIV
80
CBYP = 0
VOUT
100μV/DIV
LT1964
60
40
LT1964-5
20
0
–0.01
LT1964
COUT = 10μF
ILOAD = –200mA
CBYP = 0.01μF
–0.1
–1
–10
–100
LOAD CURRENT (mA)
1ms/DIV
1964 G26
COUT = 10μF
ILOAD = –200mA
1ms/DIV
1964 G27
–1k
1964 G25
1964fb
8
LT1964
LT1964-5, 10Hz to 100kHz Output
Noise, CBYP = 1000pF
LT1964-5, 10Hz to 100kHz Output
Noise, CBYP = 0.01μF
VOUT
100μV/DIV
VOUT
100μV/DIV
COUT = 10μF
ILOAD = –200mA
1964 G28
1ms/DIV
COUT = 10μF
ILOAD = –200mA
LT1964-5, Transient Response,
CBYP = 0.01μF
0.1
OUTPUT VOLTAGE
DEVIATION (V)
VIN = –6V
CIN = 10μF
COUT = 10μF
0.2
0
–0.1
–0.2
LOAD CURRENT
(mA)
LOAD CURRENT
(mA)
OUTPUT VOLTAGE
DEVIATION (V)
LT1964-5, Transient Response,
CBYP = 0
0
–100
–200
0
400
800
1200
TIME (μs)
1600
1964 G29
1ms/DIV
2000
1964 G30
VIN = –6V
CIN = 10μF
COUT = 10μF
0.04
0.02
0
–0.02
–0.04
0
–100
–200
0
20 40 60 80 100 120 140 160 180 200
TIME (μs)
1964 G31
1964fb
9
LT1964
PIN FUNCTIONS
ADJ (Adjustable Devices only): For the Adjustable LT1964,
this is the Input to the Error Ampliﬁer. The ADJ pin has a
bias current of 30nA that ﬂows out of the pin. The ADJ pin
voltage is –1.22V referenced to ground, and the output
voltage range is –1.22V to –20V. A parasitic diode exists
between the ADJ pin and the input of the LT1964. The ADJ
pin cannot be pulled more negative than the input during
normal operation, or more than 0.5V more negative than
the input during a fault condition.
BYP: The BYP Pin is used to Bypass the Reference of
the LT1964 to Achieve Low Noise Performance from the
Regulator. A small capacitor from the output to this pin
will bypass the reference to lower the output voltage noise.
A maximum value of 0.01μF can be used for reducing
output voltage noise to a typical 30μVRMS over a 10Hz
to 100kHz bandwidth. If not used, this pin must be left
unconnected.
Exposed Pad (DFN Package Only): IN. Connect to IN
(Pins 7, 8) at the PCB.
GND: Ground.
IN: Power is Supplied to the Device Through the Input Pin.
A bypass capacitor is required on this pin if the device
is more than six inches away from the main input ﬁlter
capacitor. In general, the output impedance of a battery
rises with frequency, so it is advisable to include a bypass
capacitor in battery-powered circuits. A bypass capacitor
in the range of 1μF to 10μF is sufﬁcient.
OUT: The Output Supplies Power to the Load. A minimum
output capacitor of 1μF is required to prevent oscillations.
Larger output capacitors will be required for applications
with large transient loads to limit peak voltage transients.
A parasitic diode exists between the output and the input.
The output cannot be pulled more negative than the input
during normal operation, or more than 0.5V below the input
during a fault condition. See the Applications Information
section for more information on output capacitance and
reverse output characteristics.
SHDN: The SHDN Pin is used to put the LT1964 into a Low
Power Shutdown State. The SHDN pin is referenced to
the GND pin for regulator control, allowing the LT1964 to
be driven by either positive or negative logic. The output
of the LT1964 will be off when the SHDN pin is pulled
within ±0.8V of GND. Pulling the SHDN pin more than
–1.9V or +1.6V will turn the LT1964 on. The SHDN pin
can be driven by 5V logic or open collector logic with a
pull-up resistor. The pull-up resistor is required to supply
the pull-up current of the open collector gate, normally
several microamperes, and the SHDN pin current, typically 3μA out of the pin (for negative logic) or 6μA into
the pin (for positive logic). If unused, the SHDN pin must
be connected to VIN. The device will be shut down if the
SHDN pin is open circuit. For the LT1964-BYP, the SHDN
pin is internally connected to VIN. A parasitic diode exists
between the SHDN pin and the input of the LT1964. The
SHDN pin cannot be pulled more negative than the input
during normal operation, or more than 0.5V below the
input during a fault condition.
1964fb
10
LT1964
APPLICATIONS INFORMATION
The LT1964 is a 200mA negative low dropout regulator with
micropower quiescent current and shutdown. The device
is capable of supplying 200mA at a dropout voltage of
340mV. Output voltage noise can be lowered to 30μVRMS
over a 10Hz to 100kHz bandwidth with the addition of a
0.01μF reference bypass capacitor. Additionally, the reference bypass capacitor will improve transient response of
the regulator, lowering the settling time for transient load
conditions. The low operating quiescent current (30μA)
drops to 3μA in shutdown. In addition to the low quiescent current, the LT1964 incorporates several protection
features which make it ideal for use in battery-powered
systems. In dual supply applications where the regulator
load is returned to a positive supply, the output can be
pulled above ground by as much as 20V and still allow
the device to start and operate.
the formula in Figure 1. The value of R1 should be less
than 250k to minimize errors in the output voltage caused
by the ADJ pin bias current. Note that in shutdown the
output is turned off and the divider current will be zero.
Curves of ADJ Pin Voltage vs Temperature and ADJ Pin Bias
Current vs Temperature appear in the Typical Performance
Characteristics section.
The adjustable device is tested and speciﬁed with the ADJ
pin tied to the OUT pin and a 5μA DC load (unless otherwise
speciﬁed) for an output voltage of –1.22V. Speciﬁcations
for output voltages greater than –1.22V will be proportional to the ratio of the desired output voltage to –1.22V;
(VOUT/–1.22V). For example, load regulation for an output
current change of 1mA to 200mA is 2mV typical at VOUT =
–1.22V. At VOUT = –12V, load regulation is:
(–12V/–1.22V) • (2mV) = 19.6mV
Adjustable Operation
The adjustable version of the LT1964 has an output voltage range of –1.22V to –20V. The output voltage is set by
the ratio of two external resistors as shown in Figure 1.
The device servos the output to maintain the voltage at
the ADJ pin at –1.22V referenced to ground. The current
in R1 is then equal to –1.22V/R1 and the current in R2 is
the current in R1 plus the ADJ pin bias current. The ADJ
pin bias current, 30nA at 25°C, ﬂows through R2 out of
the ADJ pin. The output voltage can be calculated using
R1
GND
+
ADJ
VIN
LT1964
IN
R2
OUT
VOUT
1964 F01
VOUT = –1.22V(1 + R2 ) – (IADJ)(R2)
R1
VADJ = –1.22V
IADJ = 30nA AT 25°C
OUTPUT RANGE = –1.22V TO –20V
Figure 1. Adjustable Operation
Bypass Capacitance and Low Noise Performance
The LT1964 may be used with the addition of a bypass
capacitor from VOUT to the BYP pin to lower output voltage
noise. A good quality low leakage capacitor is recommended. This capacitor will bypass the reference of the
LT1964, providing a low frequency noise pole. The noise
pole provided by this bypass capacitor will lower the output voltage noise to as low as 30μVRMS with the addition
of a 0.01μF bypass capacitor. Using a bypass capacitor
has the added beneﬁt of improving transient response.
With no bypass capacitor and a 10μF output capacitor, a
–10mA to –200mA load step will settle to within 1% of
its ﬁnal value in less than 100μs. With the addition of a
0.01μF bypass capacitor, the output will stay within 1%
for the same –10mA to –200mA load step (see LT1964-5
Transient Response in the Typical Characteristics section).
However, regulator start-up time is proportional to the size
of the bypass capacitor.
Higher values of output voltage noise may be measured
if care is not exercised with regard to circuit layout and
testing. Crosstalk from nearby traces can induce unwanted
noise onto the output of the LT1964-X.
1964fb
11
LT1964
APPLICATIONS INFORMATION
Extra consideration must be given to the use of ceramic
capacitors. Ceramic capacitors are manufactured with a
variety of dielectrics, each with different behavior across
temperature and applied voltage. The most common
dielectrics used are speciﬁed with EIA temperature characteristic codes of Z5U, Y5V, X5R and X7R. The Z5U and
Y5V dielectrics are good for providing high capacitances
in a small package, but they tend to have strong voltage
and temperature coefﬁcients as shown in Figures 2 and 3.
When used with a 5V regulator, a 16V 10μF Y5V capacitor
can exhibit an effective value as low as 1μF to 2μF for the
DC bias voltage applied and over the operating temperature range. The X5R and X7R dielectrics result in more
stable characteristics and are more suitable for use as the
output capacitor. The X7R type has better stability across
temperature, while the X5R is less expensive and is available in higher values. Care still must be exercised when
using X5R and X7R capacitors; the X5R and X7R codes
only specify operating temperature range and maximum
capacitance change over temperature. Capacitance change
due to DC bias with X5R and X7R capacitors is better than
Y5V and Z5U capacitors, but can still be signiﬁcant enough
to drop capacitor values below appropriate levels. Capacitor DC bias characteristics tend to improve as component
case size increases, but expected capacitance at operating
voltage should be veriﬁed.
20
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10μF
0
CHANGE IN VALUE (%)
The LT1964 is designed to be stable with a wide range
of output capacitors. The ESR of the output capacitor
affects stability, most notably with small capacitors. A
minimum output capacitor of 1μF with an ESR of 3Ω or
less is recommended to prevent oscillations. The LT1964
is a micropower device and output transient response
will be a function of output capacitance. Larger values
of output capacitance decrease the peak deviations and
provide improved transient response for larger load current
changes. Bypass capacitors, used to decouple individual
components powered by the LT1964, will increase the
effective output capacitor value.
Voltage and temperature coefﬁcients are not the only
sources of problems. Some ceramic capacitors have a
piezoelectric response. A piezoelectric device generates
voltage across its terminals due to mechanical stress,
similar to the way a piezoelectric accelerometer or microphone works. For a ceramic capacitor the stress can be
induced by vibrations in the system or thermal transients.
The resulting voltages produced can cause appreciable
X5R
–20
–40
–60
Y5V
–80
–100
0
2
4
14
8
6
10 12
DC BIAS VOLTAGE (V)
16
1964 F02
Figure 2. Ceramic Capacitor DC Bias Characteristics
40
20
CHANGE IN VALUE (%)
Output Capacitance and Transient Response
X5R
0
–20
–40
Y5V
–60
–80
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10μF
–100
–50 –25
50
25
75
0
TEMPERATURE (°C)
100
125
1964 F03
Figure 3. Ceramic Capacitor Temperature Characteristics
1964fb
12
LT1964
APPLICATIONS INFORMATION
amounts of noise, especially when a ceramic capacitor is
used for noise bypassing. A ceramic capacitor produced
Figure 4’s trace in response to light tapping from a pencil.
Similar vibration induced behavior can masquerade as
increased output voltage noise.
For surface mount devices, heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Copper board stiffeners and plated
through-holes can also be used to spread the heat generated by power devices.
The following tables list thermal resistance for several
different board sizes and copper areas. All measurements
were taken in still air on 3/32" FR-4 board with one ounce
copper.
VOUT
1mV/DIV
Table 1. SOT-23 Thermal Resistance
COPPER AREA
LT1964-5
COUT = 10μF
CBYP = 0.01μF
ILOAD = –200mA
100ms/DIV
1964 F04
Figure 4. Noise Resulting from Tapping on a Ceramic Capacitor
Thermal Considerations
The power handling capability of the device will be limited
by the maximum rated junction temperature (125°C). The
power dissipated by the device will be made up of two
components:
1. Output current multiplied by the input/output voltage
differential: IOUT • (VIN – VOUT), and
2. Ground pin current multiplied by the input voltage:
IGND • VIN
The GND pin current can be found by examining the GND
Pin Current curves in the Typical Performance Characteristics. Power dissipation will be equal to the sum of the
two components listed above.
The LT1964 series regulators have internal thermal limiting
designed to protect the device during overload conditions.
For continuous normal conditions the maximum junction
temperature rating of 125°C must not be exceeded. It is
important to give careful consideration to all sources of
thermal resistance from junction to ambient. Additional
heat sources mounted nearby must also be considered.
TOPSIDE*
BACKSIDE
BOARD AREA
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
2500mm2
2500mm2
2500mm2
125°C/W
1000mm2
2500mm2
2500mm2
125°C/W
225mm2
2500mm2
2500mm2
130°C/W
100mm2
2500mm2
2500mm2
135°C/W
50mm2
2500mm2
2500mm2
150°C/W
*Device is mounted on topside.
Table 2. DFN Thermal Resistance
COPPER AREA
TOPSIDE*
BACKSIDE
BOARD AREA
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
2500mm2
2500mm2
2500mm2
40°C/W
1000mm2
2500mm2
2500mm2
45°C/W
225mm2
2500mm2
2500mm2
50°C/W
100mm2
2500mm2
2500mm2
62°C/W
*Device is mounted on topside.
The thermal resistance junction-to-case (θJC), measured
at Pin 2, is 60°C/W. for the SOT-23 package and is 16°C/W
measured at the backside of the exposed pad on the DFN
package
Calculating Junction Temperature
Example: Given an output voltage of –5V, an input voltage
range of –6V to –8V, an output current range of 0mA to
–100mA, and a maximum ambient temperature of 50°C,
what will the maximum junction temperature be?
The power dissipated by the device will be equal to:
1964fb
13
LT1964
APPLICATIONS INFORMATION
IOUT(MAX) • (VIN(MAX) – VOUT) + (IGND • VIN(MAX))
where,
IOUT(MAX) = –100mA
VIN(MAX) = –8V
IGND at (IOUT = –100mA, VIN = –8V) = –2mA
so,
P = –100mA • (–8V + 5V) + (–2mA • –8V) = 0.32W
The thermal resistance (junction to ambient) will be in the
range of 125°C/W to 150°C/W for the SOT-23 package
depending on the copper area. So the junction temperature
rise above ambient will be approximately equal to:
0.32W • 140°C/W = 44.2°C
The maximum junction temperature will then be equal to
the maximum junction temperature rise above ambient
plus the maximum ambient temperature or:
TJMAX = 50°C + 44.2°C = 94.2°C
Protection Features
The LT1964 incorporates several protection features
which make it ideal for use in battery-powered circuits.
In addition to the normal protection features associated
with monolithic regulators, such as current limiting and
thermal limiting, the device is protected against reverse
input voltages and reverse output voltages.
Current limit protection and thermal overload protection
are intended to protect the device against current overload
conditions at the output of the device. For normal operation,
the junction temperature should not exceed 125°C.
The output of the LT1964 can be pulled above ground
without damaging the device. If the input is left open circuit
or grounded, the output can be pulled above ground by
20V. For ﬁxed voltage versions, the output will act like a
large resistor, typically 500k or higher, limiting current ﬂow
to less than 40μA. For adjustable versions, the output will
act like an open circuit, no current will ﬂow into the pin.
If the input is powered by a voltage source, the output
will sink the short-circuit current of the device and will
protect itself by thermal limiting. In this case, grounding
the SHDN pin will turn off the device and stop the output
from sinking the short-circuit current.
Like many IC power regulators, the LT1964 series have
safe operating area protection. The safe area protection
activates at input-to-output differential voltages greater
than –7V. The safe area protection decreases the current
limit as the input-to-output differential voltage increases
and keeps the power transistor inside a safe operating
region for all values of forward input to-output voltage.
The protection is designed to provide some output current
at all values of input-to-output voltage up to the device
breakdown. A 50μA load is required at input-to-output
differential voltages greater than –7V.
When power is ﬁrst turned on, as the input voltage rises,
the output follows the input, allowing the regulator to start
up into very heavy loads. During start-up, as the input
voltage is rising, the input-to-output voltage differential
is small, allowing the regulator to supply large output
currents. With a high input voltage, a problem can occur
wherein removal of an output short will not allow the
output voltage to fully recover. Other regulators, such as
the LT1175, also exhibit this phenomenon, so it is not
unique to the LT1964 series.
The problem occurs with a heavy output load when
the input voltage is high and the output voltage is low.
Common situations are immediately after the removal of
a short-circuit or when the SHDN pin is pulled high after
the input voltage has already been turned on. The load line
for such a load may intersect the output current curve at
two points. If this happens, there are two stable operating points for the regulator. With this double intersection,
the input supply may need to be cycled down to zero and
brought up again to make the output recover.
1964fb
14
LT1964
PACKAGE DESCRIPTION
S5 Package
5-Lead Plastic TSOT-23
(Reference LTC DWG # 05-08-1635)
0.62
MAX
0.95
REF
2.90 BSC
(NOTE 4)
1.22 REF
1.4 MIN
3.85 MAX 2.62 REF
2.80 BSC
1.50 – 1.75
(NOTE 4)
PIN ONE
RECOMMENDED SOLDER PAD LAYOUT
PER IPC CALCULATOR
0.30 – 0.45 TYP
5 PLCS (NOTE 3)
0.95 BSC
0.80 – 0.90
0.20 BSC
0.01 – 0.10
1.00 MAX
DATUM ‘A’
0.30 – 0.50 REF
1.90 BSC
0.09 – 0.20
(NOTE 3)
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DRAWING NOT TO SCALE
3. DIMENSIONS ARE INCLUSIVE OF PLATING
4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
5. MOLD FLASH SHALL NOT EXCEED 0.254mm
6. JEDEC PACKAGE REFERENCE IS MO-193
S5 TSOT-23 0302 REV B
DD Package
8-Lead Plastic DFN (3mm × 3mm)
(Reference LTC DWG # 05-08-1698)
R = 0.115
TYP
5
0.38 ± 0.10
8
0.675 ±0.05
3.5 ±0.05
1.65 ±0.05
2.15 ±0.05 (2 SIDES)
3.00 ±0.10
(4 SIDES)
PACKAGE
OUTLINE
1.65 ± 0.10
(2 SIDES)
PIN 1
TOP MARK
(NOTE 6)
(DD) DFN 1203
0.200 REF
0.25 ± 0.05
0.50
BSC
2.38 ±0.05
(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
0.75 ±0.05
4
0.25 ± 0.05
1
0.50 BSC
0.00 – 0.05
2.38 ±0.10
(2 SIDES)
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1)
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON TOP AND BOTTOM OF PACKAGE
1964fb
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
15
LT1964
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1120
125mA Micropower Low Dropout Regulator with Comparator
and Shutdown
Includes 2.5V Reference and Comparator, VIN: 3.5V to 36V, IQ = 40μA,
N8 Package
LT1121
150mA Micropower Low Dropout Regulator
VIN: 4.2V to 30V, IQ = 30μA; ThinSOT, S8 and MS8 Packages
LT1129
700mA Micropower Low Dropout Regulator
VIN: 4.5V to 30V, IQ = 50μA; DD and S8 Packages
LT1175
800mA Negative Low Dropout Micropower Regulator
VIN: 4.5V to 20V, IQ = 45μA, 0.26V Dropout Voltage, S8 and
ThinSOT Packages
LT1611
Inverting 1.4MHz Switching Regulator
–5V at 150mA from 5V Input, ThinSOT Package
LT1761 Series
100mA, Low Noise, Low Dropout Micropower Regulators
VIN: 1.5V to 20V, IQ = 20μA, 20μVRMS Noise, ThinSOT Package
LT1762 Series
150mA, Low Noise, LDO Micropower Regulators
VIN: 1.5V to 20V, IQ = 25μA, 20μVRMS Noise, MS8 Package
LT1763 Series
500mA, Low Noise, LDO Micropower Regulators
VIN: 1.5V to 20V, IQ = 30μA, 20μVRMS Noise, S8 Package
LT1764A
3A, Low Noise, Fast Transient Response LDO
VIN: 1.5V to 20V, 40μVRMS Noise; DD and T5 Packages
LT1931/LT1931A
Inverting 1.2MHz/2.2MHz Switching Regulators
–5V at 350mA from 5V Input, ThinSOT Package
LT1962
300mA, Low Noise, LDO Micropower Regulator
VIN: 1.5V to 20V, IQ = 30μA, 20μVRMS Noise, MS8 Package
LT1963A
1.5A, Low Noise, Fast Transient Response LDO
VIN: 1.5V to 20V, 40μVRMS Noise; DD, T5, S8 and ThinSOT Packages
1964fb
16 Linear Technology Corporation
LT 0708 REV B • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2001

Open as PDF

Similar pages