LINER LTC2301IMS

LTC2301/LTC2305
1-/2-Channel, 12-Bit ADCs
with I2C Compatible Interface
DESCRIPTION
FEATURES
n
n
n
n
n
n
n
n
n
n
n
n
n
n
12-Bit Resolution
Low Power: 1.5mW at 1ksps, 35μW Sleep Mode
14ksps Throughput Rate
Internal Reference
Low Noise: SNR = 73.5dB
Guaranteed No Missing Codes
Single 5V Supply
2-wire I2C Compatible Serial Interface with 9
Addresses Plus One Global for Synchronization
Fast Conversion Time: 1.3μs
1-Channel (LTC2301) and 2-Channel (LTC2305)
Versions
Unipolar or Bipolar Input Ranges (Software
Selectable)
Internal Conversion Clock
Guaranteed Operation from –40°C to 125°C
(MSOP Package)
12-Pin 4mm × 3mm DFN and 12-Pin MSOP
Packages
APPLICATIONS
n
n
n
n
n
n
Industrial Process Control
Motor Control
Accelerometer Measurements
Battery Operated Instruments
Isolated and/or Remote Data Acquisition
Power Supply Monitoring
The LTC®2301/LTC2305 are low noise, low power, 1-/2channel, 12-bit successive approximation ADCs with an I2C
compatible serial interface. These ADCs include an internal
reference and a fully differential sample-and-hold circuit
to reduce common-mode noise. The LTC2301/LTC2305
operate from an internal clock to achieve a fast 1.3μs
conversion time.
The LTC2301/LTC2305 operate from a single 5V supply
and draw just 300μA at a throughput rate of 1ksps. The
ADC enters nap mode when not converting, reducing the
power dissipation.
The LTC2301/LTC2305 are available in small 12-pin
4mm × 3mm DFN and 12-pin MSOP packages. The internal 2.5V reference further reduces PCB board space
requirements.
The low power consumption and small size make the
LTC2301/LTC2305 ideal for battery operated and portable
applications, while the 2-wire I2C compatible serial interface
makes these ADCs a good match for space-constrained
systems.
12-Bit I2C ADC Famly
Input Channels
Part Number
1
2
8
LTC2301
LTC2305
LTC2309
L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
BLOCK DIAGRAM
Integral Nonlinearity vs Output Code (LTC2305)
5V
10μF
1.00
0.1μF
0.75
VDD
CH0(IN+)
ANALOG INPUT
0V TO 4.096V UNIPOLAR CH1(IN+)
±2.048V BIPOLAR
ANALOG
INPUT
MUX
+
AD1
AD0
12-BIT
SAR ADC
–
I2C
PORT
0.50
INL (LSB)
LTC2301
LTC2305
SCL
SDA
–0.50
2.2μF
PIN NAMES IN PARENTHESES
REFER TO LTC2301
GND
23015 TA01a
0.00
–0.25
VREF
INTERNAL
2.5V REF
0.25
0.1μF
–0.75
REFCOMP
10μF
–1.00
0
1024
2048
3072
OUTPUT CODE
4096
23015 TA01b
23015f
1
LTC2301/LTC2305
ABSOLUTE MAXIMUM RATINGS
(Notes 1,2)
Supply Voltage (VDD) ................................ –0.3V to 6.0V
Analog Input Voltage
CH0(IN+), CH1(IN–), REF,
REFCOMP .....................(GND – 0.3V) to (VDD + 0.3V)
Digital Input Voltage..........(GND – 0.3V) to (VDD + 0.3V)
Digital Output Voltage .......(GND – 0.3V) to (VDD + 0.3V)
Power Dissipation ...............................................500mW
Operating Temperature Range
LTC2301C/LTC2305C ............................... 0°C to 70°C
LTC2301I/LTC2305I.............................. –40°C to 85°C
LTC2301H/LTC2305H (Note 13) ......... –40°C to 125°C
Storage Temperature Range................... –65°C to 150°C
PIN CONFIGURATION
LTC2305
LTC2301
TOP VIEW
TOP VIEW
GND
1
12 AD0
GND
1
12 AD0
SDA
2
11 AD1
SDA
2
11 AD1
SCL
3
10 VDD
SCL
3
GND
4
9
GND
4
9
GND
+
5
8
REFCOMP
6
7
VREF
13
GND
CH0
5
8
REFCOMP
IN
CH1
6
7
VREF
IN–
13
10 VDD
DE PACKAGE
12-LEAD (4mm × 3mm) PLASTIC DFN
DE PACKAGE
12-LEAD (4mm × 3mm) PLASTIC DFN
TJMAX = 150°C, θJA = 43°C/W
EXPOSED PAD (PIN 13) IS GND, MUST BE SOLDERED TO PCB
TJMAX = 150°C, θJA = 43°C/W
EXPOSED PAD (PIN 13) IS GND, MUST BE SOLDERED TO PCB
LTC2305
LTC2301
TOP VIEW
GND
SDA
SCL
GND
CH0
CH1
1
2
3
4
5
6
12
11
10
9
8
7
AD0
AD1
VDD
GND
REFCOMP
VREF
MS PACKAGE
12-LEAD PLASTIC MSOP
TJMAX = 150°C, θJA = 130°C/W
TOP VIEW
GND
SDA
SCL
GND
IN+
IN–
1
2
3
4
5
6
12
11
10
9
8
7
AD0
AD1
VDD
GND
REFCOMP
VREF
MS PACKAGE
12-LEAD PLASTIC MSOP
TJMAX = 150°C, θJA = 130°C/W
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC2301CDE#PBF
LTC2301CDE#TRPBF
2301
12-Lead (3mm × 4mm) Plastic DFN
0°C to 70°C
LTC2301IDE#PBF
LTC2301IDE#TRPBF
2301
12-Lead (3mm × 4mm) Plastic DFN
–40°C to 85°C
LTC2305CDE#PBF
LTC2305CDE#TRPBF
2305
12-Lead (3mm × 4mm) Plastic DFN
0°C to 70°C
LTC2305IDE#PBF
LTC2305IDE#TRPBF
2305
12-Lead (3mm × 4mm) Plastic DFN
–40°C to 85°C
LTC2301CMS#PBF
LTC2301CMS#TRPBF
2301
12-Lead Plastic MSOP
0°C to 70°C
LTC2301IMS#PBF
LTC2301IMS#TRPBF
2301
12-Lead Plastic MSOP
–40°C to 85°C
LTC2301HMS#PBF
LTC2301HMS#TRPBF
2301
12-Lead Plastic MSOP
–40°C to 125°C
LTC2305CMS#PBF
LTC2305CMS#TRPBF
2305
12-Lead Plastic MSOP
0°C to 70°C
23015f
2
LTC2301/LTC2305
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC2305IMS#PBF
LTC2305IMS#TRPBF
2305
12-Lead Plastic MSOP
–40°C to 85°C
LTC2305HMS#PBF
LTC2305HMS#TRPBF
2305
12-Lead Plastic MSOP
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
CONVERTER AND MULTIPLEXER CHARACTERISTICS
The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 4)
PARAMETER
CONDITIONS
MIN
TYP
MAX
l
±0.4
±1
LSB
Differential Linearity Error
l
±0.3
±1
LSB
Bipolar Zero Error
l
±0.5
±8
l
Resolution (No Missing Codes)
Integral Linearity Error
(Note 5)
(Note 6)
12
Bits
Bipolar Zero Error Drift
Unipolar Zero Error
0.002
l
(Note 6)
UNITS
±0.7
LSB
LSB/°C
±6
LSB
Unipolar Zero Error Drift
0.002
Unipolar Zero Error Match (LTC2305)
±0.1
±1
LSB
l
l
±1
±0.9
±10
±9
LSB
LSB
l
l
±0.5
±0.7
Bipolar Full-Scale Error
External Reference (Note 7)
REFCOMP = 4.096V (Note 7)
Bipolar Full-Scale Error Drift
External Reference
Unipolar Full-Scale Error
External Reference (Note 7)
REFCOMP = 4.096V (Note 7)
Unipolar Full-Scale Error Drift
External Reference
LSB/°C
0.05
LSB/°C
±10
±6
0.05
Unipolar Full-Scale Error Match (LTC2305)
±0.1
LSB
LSB
LSB/°C
±2
LSB
ANALOG INPUT
The l denotes the specifications which apply over the full operating temperature range, otherwise
specifications are at TA = 25°C. (Note 4)
SYMBOL
PARAMETER
CONDITIONS
VIN+
Absolute Input Range (CH0, CH1, IN+)
(Note 8)
l
–0.05
MIN
TYP
REFCOMP
V
VIN–
Absolute Input Range (CH0, CH1, IN–)
Unipolar (Note 8)
Bipolar (Note 8)
l
–0.05
–0.05
0.25 • REFCOMP
0.75 • REFCOMP
V
V
VIN+ – VIN–
Input Differential Voltage Range
VIN = VIN+ – VIN– (Unipolar)
VIN = VIN+ – VIN– (Bipolar)
l
IIN
Analog Input Leakage Current
CIN
Analog Input Capacitance
CMRR
Input Common Mode Rejection Ratio
0 to REFCOMP
±REFCOMP/2
l
Sample Mode
Hold Mode
MAX
UNITS
V
V
±1
μA
55
5
pF
pF
70
dB
23015f
3
LTC2301/LTC2305
DYNAMIC ACCURACY
The l denotes the specifications which apply over the full operating temperature range,
otherwise specifications are at TA = 25°C and AIN = –1dBFS. (Notes 4,9)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
SINAD
Signal-to-(Noise + Distortion) Ratio
fIN = 1kHz
l
71
73.4
SNR
Signal-to-Noise Ratio
THD
Total Harmonic Distortion
fIN = 1kHz
l
71
73.5
fIN = 1kHz
l
SFDR
Spurious Free Dynamic Range
fIN = 1kHz, First 5 Harmonics
l
Channel-to-Channel Isolation
–91
79
MAX
UNITS
dB
dB
–77
dB
92
dB
fIN = 1kHz
–109
dB
Full Linear Bandwidth
fIN = 1kHz
700
kHz
–3dB Input Linear Bandwidth
(Note 10)
25
MHz
13
ns
240
ns
Aperture Delay
Transient Response
Full-Scale Step
INTERNAL REFERENCE CHARACTERISTICS
The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Notes 4)
PARAMETER
CONDITIONS
VREF Output Voltage
IOUT = 0
VREF Output Tempco
IOUT = 0
VREF Output Impedance
–0.1mA ≤ IOUT ≤ 0.1mA
VREFCOMP Output Voltage
IOUT = 0
VREF Line Regulation
VDD = 4.75V to 5.25V
l
MIN
TYP
MAX
UNITS
2.46
2.50
2.54
V
±25
ppm/°C
8
kΩ
4.096
V
0.8
mV/V
I2C INPUTS AND DIGITAL OUTPUTS
The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Notes 4)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
VIH
High Level Input Voltage
l
VIL
Low Level Input Voltage
l
VIHA
High Level Input Voltage for Address Pins A1, A0
l
VILA
Low Level Input Voltage for Address Pins A1, A0
l
0.25
RINH
Resistance from A1, A0 to VDD to Set Chip
Address Bit to 1
l
10
kΩ
RINL
Resistance from A1, A0 to GND to Set Chip
Address Bit to 0
l
10
kΩ
RINF
Resistance from A1, A0 to GND or VDD to Set
Chip Address Bit to Float
l
2
II
Digital Input Current
VIN = VDD
l
–10
VHYS
Hysteresis of Schmitt Trigger Inputs
(Note 8)
l
0.25
VOL
Low Level Output Voltage (SDA)
I = 3mA
l
tOF
Output Fall Time VIN(MIN) to VIL(MAX)
Bus Load CB 10pF to 400pF (Note 11)
l
tSP
Input Spike Suppression
CCAX
External Capacitance Load on Chip Address Pins
(A1, A0) for Valid Float
2.85
V
1.5
4.75
V
V
V
MΩ
10
μA
V
0.4
V
250
ns
l
50
ns
l
10
pF
20 + 0.1CB
23015f
4
LTC2301/LTC2305
POWER REQUIREMENTS
The l denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. (Note 4)
SYMBOL
PARAMETER
CONDITIONS
MIN
l
4.75
TYP
MAX
UNITS
VDD
Supply Voltage
5
5.25
V
IDD
Supply Current
Nap Mode
Sleep Mode
14ksps Sample Rate
SLP Bit = 0, Conversion Done
SLP Bit = 1, Conversion Done
l
l
l
2.3
225
7
3.5
400
15
mA
μA
μA
PD
Power Dissipation
Nap Mode
Sleep Mode
14ksps Sample Rate
SLP Bit = 0, Conversion Done
SLP Bit = 1, Conversion Done
l
l
l
11.5
1.125
35
17.5
2
75
mW
mW
μW
I2C TIMING CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 4)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
400
kHz
fSCL
SCL Clock Frequency
l
tHD(SDA)
Hold Time (Repeated) Start Condition
l
0.6
μs
tLOW
Low Period of the SCL Pin
l
1.3
μs
tHIGH
High Period of the SCL Pin
l
0.6
μs
tSU(STA)
Set-Up Time for a Repeated Start
Condition
l
0.6
μs
tHD(DAT)
Data Hold Time
l
0
tSU(DAT)
Data Set-Up Time
l
100
tr
Rise Time for SDA/SCL Signals
(Note 11)
l
20 + 0.1CB
300
ns
tf
Fall Time for SDA/SCL Signals
(Note 11)
l
20 + 0.1CB
300
ns
0.6
μs
1.3
μs
tSU(STO)
Set-Up Time for Stop Condition
l
tBUF
Bus Free Time Between a Second Start
Condition
l
0.9
μs
ns
ADC TIMING CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 4)
SYMBOL
PARAMETER
CONDITIONS
fSMPL
Throughput Rate (Successive Reads)
tCONV
Conversion Time
tACQ
Acquisition Time
(Note 8)
tREFWAKE
REFCOMP Wakeup Time (Note 12)
CREFCOMP = 10μF, CREF = 2.2μF
MIN
TYP
l
l
MAX
14
1.3
l
200
UNITS
ksps
1.6
μs
240
ns
ms
23015f
5
LTC2301/LTC2305
ELECTRICAL CHARACTERISTICS
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: All voltage values are with respect to ground.
Note 3: When these pin voltages are taken below ground or above VDD,
they will be clamped by internal diodes. These products can handle input
currents greater than 100mA below ground or above VDD without latchup.
Note 4: VDD = 5V, fSMPL = 14kHz, internal reference unless otherwise
noted.
Note 5: Integral nonlinearity is defined as the deviation of a code from a
straight line passing through the actual endpoints of the transfer curve.
The deviation is measured from the center of the quantization band.
Note 6: Bipolar zero error is the offset voltage measured from –0.5LSB
when the output code flickers between 0000 0000 0000 and 1111 1111
1111. Unipolar zero error is the offset voltage measured from 0.5LSB
when the output code flickers between 0000 0000 0000 and 0000 0000
0001.
Note 7: Full-scale bipolar error is the worst-case of –FS or FS untrimmed
deviation from ideal first and last code transitions and includes the effect
of offset error. Unipolar full-scale error is the deviation of the last code
transition from ideal and includes the effect of offset error.
Note 8: Guaranteed by design, not subject to test.
Note 9: All specifications in dB are referred to a full-scale ±2.048V input
with a 2.5V reference voltage.
Note 10: Full linear bandwidth is defined as the full-scale input frequency
at which the SINAD degrades to 60dB or 10 bits of accuracy.
Note 11: CB = capacitance of one bus line in pF (10pF ≤ CB ≤ 400pF)
Note 12: REFCOMP wakeup time is the time required for the REFCOMP pin
to settle within 0.5LSB at 12-bit resolution of its final value after waking up
from sleep mode.
Note 13: High temperatures degrade operating lifetimes. Operating lifetime
is derated at temperatures greater than 105°C.
23015f
6
LTC2301/LTC2305
TYPICAL PERFORMANCE CHARACTERISTICS
(LTC2301) TA = 25°C, VDD = 5V, fSMPL = 14ksps, unless otherwise noted.
1.00
1.00
0.75
0.75
0.50
0.50
0.25
0.25
0.00
–0.25
0.00
–0.25
–0.50
–0.50
–0.75
–0.75
–1.00
1024
0
2048
3072
OUTPUT CODE
4096
1kHz Sine Wave
8192 Point FFT Plot
MAGNITUDE (dB)
Differential Nonlinearity
vs Output Code
DNL (LSB)
INL (LSB)
Integral Nonlinearity
vs Output Code
–1.00
1024
0
2048
3072
OUTPUT CODE
4096
23015 G01
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
–140
SNR = 73.2 dB
SINAD = 73.1 dB
THD = –80dB
0
1
2
3
4
5
FREQUENCY (kHz)
23015 G02
Supply Current
vs Sampling Frequency
7
6
23015 G03
Offset Error vs Temperature
Full-Scale Error vs Temperature
2.5
1.5
4
2.0
1.0
2
1.5
1.0
0.5
0.5
BIPOLAR
0.0
UNIPOLAR
–0.5
0
0.1
1
10
SAMPLING FREQUENCY (ksps)
100
FULL-SCALE ERROR (LSB)
OFFSET ERROR (LSB)
SUPPLY CURRENT (mA)
UNIPOLAR
–1.0
–50
–25
0
50
25
75
TEMPERATURE (°C)
100
23015 G04
BIPOLAR
0
–2
–4
–6
–50
125
–25
0
50
25
75
TEMPERATURE (°C)
100
23015 G06
23015 G05
Supply Current vs Temperature
Analog Input Leakage Current
vs Temperature
Sleep Current vs Temperature
2.4
125
10
1000
1.8
1.6
800
LEAKAGE CURRENT (nA)
2.2
SLEEP CURRENT (μA)
SUPPLY CURRENT (mA)
900
8
6
4
2
700
600
500
400
300
200
100
1.4
–50
–25
25
75
0
50
TEMPERATURE (°C)
100
125
23015 G07
0
–50
–25
25
75
0
50
TEMPERATURE (°C)
100
125
23015 G08
0
–50
–25
25
75
0
50
TEMPERATURE (°C)
100
125
23015 G09
23015f
7
LTC2301/LTC2305
TYPICAL PERFORMANCE CHARACTERISTICS
(LTC2305) TA = 25°C, VDD = 5V, fSMPL = 14ksps, unless otherwise noted.
Differential Nonlinearity
vs Output Code
1.00
0.75
0.75
0.50
0.50
0.25
0.25
0.00
–0.25
0.00
–0.25
–0.50
–0.50
–0.75
–0.75
–1.00
–1.00
1024
0
2048
3072
OUTPUT CODE
1kHz Sine Wave
8192 Point FFT Plot
4096
1024
0
2048
3072
OUTPUT CODE
4096
Supply Current
vs Sampling Frequency
Offset Error vs Temperature
FULL-SCALE ERROR (LSB)
OFFSET ERROR (LSB)
0.5
0.0
UNIPOLAR
0.5
1
10
SAMPLING FREQUENCY (ksps)
100
2
3
4
5
FREQUENCY (kHz)
–0.5
–50
–25
0
50
25
75
TEMPERATURE (°C)
100
2
BIPOLAR
0
UNIPOLAR
–2
–4
–6
–50
125
–25
0
50
25
75
TEMPERATURE (°C)
100
Analog Input Leakage Current
vs Temperature
Sleep Current vs Temperature
2.4
125
23015 G15
23015 G14
23015 G13
Supply Current vs Temperature
7
6
Full-Scale Error vs Temperature
BIPOLAR
0
0.1
1
4
2.0
1.0
0
23015 G12
1.0
2.5
1.5
SNR = 73.2 dB
SINAD = 73.1 dB
THD = –80dB
23015 G11
23015 G10
SUPPLY CURRENT (mA)
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
–140
MAGNITUDE (dB)
1.00
DNL (LSB)
INL (LSB)
Integral Nonlinearity
vs Output Code
1000
10
800
1.8
1.6
LEAKAGE CURRENT (nA)
2.2
SLEEP CURRENT (μA)
SUPPLY CURRENT (mA)
900
8
6
4
700
600
500
400
CH(ON)
300
CH(OFF)
200
2
100
1.4
–50
–25
25
75
0
50
TEMPERATURE (°C)
100
125
23015 G16
0
–50
–25
25
75
0
50
TEMPERATURE (°C)
100
125
23015 G17
0
–50
–25
25
75
0
50
TEMPERATURE (°C)
100
125
23015 G18
23015f
8
LTC2301/LTC2305
PIN FUNCTIONS
(LTC2301)
GND (Pins 1, 4, 9): Ground. All GND pins must be connected to a solid ground plane.
SDA (Pin 2): Bidirectional Serial Data Line of the I2C Interface. In transmitter mode (Read), the conversion result
is output at the SDA pin, while in receiver mode (Write),
the DIN word is input at the SDA pin to configure the ADC.
The pin is high impedance during the data input mode and
is an open drain output (requires an appropriate pull-up
device to VDD) during the data output mode.
SCL (Pin 3): Serial Clock Pin of the I2C Interface. The
LTC2301 can only act as a slave and the SCL pin only accepts an external serial clock. Data is shifted into the SDA
pin on the rising edges of the SCL clock and output through
the SDA pin on the falling edges of the SCL clock.
IN+, IN– (Pins 5, 6): Positive (IN+) and negative (IN–)
differential analog inputs.
VREF (Pin 7): 2.5V Reference Output. Bypass to GND with
a minimum 2.2μF tantalum capacitor or low ESR ceramic
capacitor. The internal reference may be overdriven by an
external 2.5V reference at this pin.
REFCOMP (Pin 8): Reference Buffer Output. Bypass to
GND with a 10μF low ESR ceramic or tantalum and 0.1μF
ceramic capacitor in parallel. Nominal output voltage is
4.096V. The internal reference buffer driving this pin is
disabled by grounding VREF, allowing REFCOMP to be
overdriven by an external source (see Figure 5c).
VDD (Pin 10): 5V Analog Supply. The range of VDD is 4.75V
to 5.25V. Bypass VDD to GND with a 0.1μF ceramic and a
10μF low ESR ceramic or tantalum capacitor in parallel.
AD1 (Pin 11): Chip Address Control Pin. This pin is configured as a three-state (LOW, HIGH, Floating) address
control bit for the device I2C address. See Table 2 for
address selection.
AD0 (Pin 12): Chip Address Control Pin. This pin is configured as a three-state (LOW, HIGH, Floating) address
control bit for the device I2C address. See Table 2 for
address selection.
GND (Pin 13 – DFN Package Only): Exposed Pad Ground.
Must be soldered directly to ground plane.
23015f
9
LTC2301/LTC2305
PIN FUNCTIONS
(LTC2305)
GND (Pins 1, 4, 9): Ground. All GND pins must be connected to a solid ground plane.
SDA (Pin 2): Bidirectional Serial Data Line of the I2C Interface. In transmitter mode (Read), the conversion result
is output at the SDA pin, while in receiver mode (Write),
the DIN word is input at the SDA pin to configure the ADC.
The pin is high impedance during the data input mode and
is an open drain output (requires an appropriate pull-up
device to VDD) during the data output mode.
SCL (Pin 3): Serial Clock Pin of the I2C Interface. The
LTC2305 can only act as a slave and the SCL pin only accepts an external serial clock. Data is shifted into the SDA
pin on the rising edges of the SCL clock and output through
the SDA pin on the falling edges of the SCL clock.
CH0-CH1 (Pins 5, 6): Channel 0 and Channel 1 Analog
Inputs. CH0 and CH1 can be configured as single-ended
or differential input channels. See the Analog Input Multiplexer section.
VREF (Pin 7): 2.5V Reference Output. Bypass to GND with
a minimum 2.2μF tantalum capacitor or low ESR ceramic
capacitor. The internal reference may be overdriven by an
external 2.5V reference at this pin.
REFCOMP (Pin 8): Reference Buffer Output. Bypass to
GND with a 10μF low ESR ceramic or tantalum and 0.1μF
ceramic capacitor in parallel. Nominal output voltage is
4.096V. The internal reference buffer driving this pin is
disabled by grounding VREF, allowing REFCOMP to be
overdriven by an external source (see Figure 5c).
VDD (Pin 10): 5V Analog Supply. The range of VDD is 4.75V
to 5.25V. Bypass VDD to GND with a 0.1μF ceramic and a
10μF low ESR ceramic or tantalum capacitor in parallel.
AD1 (Pin 11): Chip Address Control Pin. This pin is configured as a three-state (LOW, HIGH, Floating) address
control bit for the device I2C address. See Table 2 for
address selection.
AD0 (Pin 12): Chip Address Control Pin. This pin is configured as a three-state (LOW, HIGH, Floating) address
control bit for the device I2C address. See Table 2 for
address selection.
GND (Pin 13 – DFN Package Only): Exposed Pad Ground.
Must be soldered directly to ground plane.
23015f
10
LTC2301/LTC2305
FUNCTIONAL BLOCK DIAGRAM
VDD
AD1
AD0
LTC2301
LTC2305
CH0(IN+)
CH1(IN–)
+
ANALOG
INPUT
MUX
12-BIT
SAR ADC
I2C
PORT
SCL
8k
VREF
SDA
–
INTERNAL
2.5V REF
GAIN = 1.6384x
PIN NAMES IN PARENTHESES
REFER TO LTC2301
GND
REFCOMP
23015 BD
TIMING DIAGRAM
Definition of Timing for Fast/Standard Mode Devices on the I2C Bus
SDA
tSU(DAT)
tLOW
tf
tHD(SDA)
tf
tr
tSP
tr
tBUF
SCL
tHD(SDA)
S
tHD(DAT)
tHIGH
tSU(STA)
tSU(STO)
Sr
P
S
23015 TD
S = START, Sr = REPEATED START, P = STOP
23015f
11
LTC2301/LTC2305
APPLICATIONS INFORMATION
Overview
The LTC2301/LTC2305 are low noise, 1-/2-channel, 12-bit
successive approximation register (SAR) A/D converters
with an I2C compatible serial interface. The LTC2301/
LTC2305 both include a precision internal reference. The
LTC2305 includes a 2-channel analog input multiplexer
(MUX) while the LTC2301 includes an input MUX that allows
the polarity of the differential input to be selected. These
ADCs can operate in either unipolar or bipolar mode. Unipolar mode should be used for single-ended operation with
the LTC2305, since single-ended input signals are always
referenced to GND. A sleep mode option is also provided
to further reduce power during inactive periods.
The LTC2301/LTC2305 communicate through a 2-wire
I2C compatible serial interface. Conversions are initiated
by signaling a stop condition after the part has been
successfully addressed for a read/write operation. The
device will not acknowledge an external request until the
conversion is finished. After a conversion is finished, the
device is ready to accept a read/write request. Once the
LTC2301/LTC2305 is addressed for a read operation, the
device begins outputting the conversion result under the
control of the serial clock (SCL). There is no latency in the
conversion result. There are 12 bits of output data followed
by four trailing zeros. Data is updated on the falling edges
of SCL, allowing the user to reliably latch data on the rising edge of SCL. A write operation may follow the read
operation by using a repeat start or a stop condition may
be given to start a new conversion. By selecting a write
operation, these ADCs can be programmed by a 6-bit DIN
word. The DIN word configures the MUX and programs
various modes of operation.
During a conversion, the internal 12-bit capacitive chargeredistribution DAC output is sequenced through a successive approximation algorithm by the SAR starting from the
most significant bit (MSB) to the least significant bit (LSB).
The sampled input is successively compared with binary
weighted charges supplied by the capacitive DAC using
a differential comparator. At the end of a conversion, the
DAC output balances the analog input. The SAR contents
(a 12-bit data word) that represent the sampled analog
input are loaded into 12 output latches that allow the data
to be shifted out via the I2C interface.
Programming the LTC2301 and LTC2305
The software compatible LTC2301/LTC2305/LTC2309 family features a 6-bit DIN word to program various modes of
operation. Don’t care bits (X) are ignored. The SDA data
bits are loaded on the rising edge of SCL during a write
operation, with the S/D bit loaded on the first rising edge
and the SLP bit on the sixth rising edge (see Figure 7b
in the I2C Interface section). The input data word for the
LTC2305 is defined as follows:
S/D O/S
X
X
UNI SLP
S/D = SINGLE-ENDED/DIFFERENTIAL BIT
O/S = ODD/SIGN BIT
UNI = UNIPOLAR/BIPOLAR BIT
SLP = SLEEP MODE BIT
For the LTC2301, the input word is defined as:
X
O/S
X
X
UNI SLP
Analog Input Multiplexer
The analog input MUX is programmed by the S/D and
O/S bits of the DIN word for the LTC2305 and the O/S
bit of the DIN word for the LTC2301. Table 1 and Table 2
list the MUX configurations for all combinations of the
configuration bits. Figure 1a shows several possible MUX
configurations and Figure 1b shows how the MUX can be
reconfigured from one conversion to the next.
Table 1. Channel Configuration for the LTC2305
S/D
O/S
CH0
CH1
0
0
+
–
0
1
–
+
1
0
+
1
1
+
23015f
12
LTC2301/LTC2305
APPLICATIONS INFORMATION
Driving the Analog Inputs
Table 2. Channel Configuration for the LTC2301
O/S
IN+
IN–
0
+
–
1
–
+
2 Single-Ended
1 Differential
+ (–)
– (+) {
+
+
CH0
CH1
CH0
CH1
LTC2305
LTC2305
GND (–)
1 Differential
+ (–)
– (+) {
CH0
CH1
Input Filtering
The noise and distortion of the input amplifier and other
circuitry must be considered since they will add to the
ADC noise and distortion. Therefore, noisy input circuitry
should be filtered prior to the analog inputs to minimize
noise. A simple 1-pole RC filter is sufficient for many
applications.
LTC2301
23015 F01a
Figure 1a. Example MUX Configurations
1st Conversion
+
–{
CH0
CH1
LTC2305
The analog inputs of the LTC2301/LTC2305 are easy to
drive. Each of the analog inputs of the LTC2305 (CH0 and
CH1) can be used as single-ended input relative to GND
or as a differential pair. The analog inputs of the LTC2301
(IN+, IN–) are always configured as a differential pair.
Regardless of the MUX configuration, the “+” and “–“
inputs are sampled at the same instant. Any unwanted
signal that is common to both inputs will be reduced by
the common mode rejection of the sample-and-hold circuit. The inputs draw only one small current spike while
charging the sample-and-hold capacitors during the acquire
mode. In conversion mode, the analog inputs draw only
a small leakage current. If the source impedance of the
driving circuit is low, the ADC inputs can be driven directly.
Otherwise, more acquisition time should be allowed for a
source with higher impedance.
2nd Conversion
–
+
{
CH0
CH1
LTC2305
GND (–)
23015 F01b
Figure 1b. Changing the MUX Assignment “On the Fly”
The analog inputs of the LTC2301/LTC2305 can be modeled
as a 55pF capacitor (CIN) in series with a 100Ω resistor
(RON) as shown in Figure 2a. CIN gets switched to the
selected input once during each conversion. Large filter
RC time constants will slow the settling of the inputs. It
is important that the overall RC time constants be short
enough to allow the analog inputs to completely settle to
12-bit resolution within the acquisition time (tACQ) if DC
accuracy is important.
When using a filter with a large CFILTER value (e.g. 1μF),
the inputs do not completely settle and the capacitive input
switching currents are averaged into a net DC current(IDC).
In this case, the analog input can be modeled by an equivalent resistance (REQ = 1/(fSMPL • CIN)) in series with an
ideal voltage source (VREFCOMP/2) as shown in Figure 2b.
23015f
13
LTC2301/LTC2305
APPLICATIONS INFORMATION
The magnitude of the DC current is then approximately IDC
= (VIN – VREFCOMP/2)/REQ, which is roughly proportional to
VIN. To prevent large DC drops across the resistor RFILTER,
a filter with a small resistor and large capacitor should be
chosen. When running at the maximum throughput rate
of 14ksps, the input current equals 1.5μA at VIN = 4.096V,
which amounts to a full-scale error of 0.5LSBs when using
a filter resistor (RFILTER) of 333Ω. Applications requiring
lower sample rates can tolerate a larger filter resistor for
the same amount of full-scale error.
Figures 3a and 3b show respective examples of input
filtering for single-ended and differential inputs. For the
single-ended case in Figure 4a, a 50Ω source resistor
and a 2000pF capacitor to ground on the input will limit
the input bandwidth to 1.6MHz. High quality capacitors
and resistors should be used in the RC filter since these
components can add distortion. NPO and silver mica type
dielectric capacitors have excellent linearity. Carbon surface
mount resistors can generate distortion from self heating
Dynamic Performance
Fast Fourier Transform (FFT) test techniques are used to
test the ADC’s frequency response, distortion and noise
at the rated throughput. By applying a low distortion
sine wave and analyzing the digital output using an FFT
algorithm, the ADC’s spectral content can be examined
for frequencies outside the fundamental.
Signal-to-Noise and Distortion Ratio (SINAD)
The signal-to-noise and distortion ratio (SINAD) is the
ratio between the RMS amplitude of the fundamental input
frequency to the RMS amplitude of all other frequency
components at the A/D output. The output is band-limited
to frequencies from above DC and below half the sampling
ANALOG
INPUT
INPUT
CH0, CH1,
IN+, IN–
RSOURCE
and from damage that may occur during soldering. Metal
film surface mount resistors are much less susceptible
to both problems.
RON =
100Ω
50Ω
CH0, CH1
2000pF
LTC2301
LTC2305
VIN
LTC2305
CIN =
55pF
CFILTER
REFCOMP
10μF
0.1μF
23015 F03a
23015 F02a
Figure 2a. Analog Input Equivalent Circuit
RFILTER
IDC
Figure 3a. Optional RC Input Filtering for Single-Ended Input
1000pF
INPUT
(CH0, CH1,
IN+, IN–)
50Ω
LTC2301
REQ =
LTC2305
1/(fSMPL • CIN)
VIN
CFILTER
+
–
DIFFERENTIAL
ANALOG
INPUTS
CH0, IN+
1000pF
50Ω
LTC2301
LTC2305
CH1, IN–
1000pF
VREFCOMP/2
REFCOMP
23015 F02b
10μF
0.1μF
23015 F03b
Figure 2b. Analog Input Equivalent
Circuit for Large Filter Capacitances
Figure 3b. Optional RC Input Filtering for Differential Inputs
23015f
14
LTC2301/LTC2305
APPLICATIONS INFORMATION
MAGNITUDE (dB)
frequency. Figure 4 shows a typical SINAD of 73.2dB with
a 14kHz sampling rate and a 1kHz input. A SNR of 73.3dB
can be achieved with the LTC2301/LTC2305.
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
–140
SNR = 73.2dB
SINAD = 73.1dB
THD = –80dB
a 0.1μF ceramic capacitor for best noise performance. The
internal reference buffer can also be overdriven from 1V
to VDD with an external reference at REFCOMP as shown
in Figure 5c. To do so, VREF must be grounded to disable
the reference buffer. This will result in an input range of
0V to VREFCOMP in unipolar mode and ±0.5 • VREFCOMP in
bipolar mode.
R1
8k
VREF
2.5V
BANDGAP
REFERENCE
2.2μF
REFCOMP
4.096V
0
1
2
3
4
5
FREQUENCY (kHz)
7
6
REFERENCE
AMP
+
10μF
R2
0.1μF
23015 F04
Figure 4. 1kHz Sine Wave 8192 Point FFT Plot
R3
GND
LTC2301
LTC2305
Total Harmonic Distortion (THD)
23015 F05a
Total Harmonic Distortion (THD) is the ratio of the RMS
sum of all harmonics of the input signal to the fundamental
itself. The out-of-band harmonics alias into the frequency
band between DC and half the sampling frequency(fSMPL/2).
THD is expressed as:
V2 2 + V3 2 + V4 2 ... + VN 2
THD = 20log
V1
Figure 5a. LTC2301/LTC2305 Reference Circuit
5V
0.1μF
VIN
LT1790A-2.5
VOUT
VREF
2.2μF
where V1 is the RMS amplitude of the fundamental frequency and V2 through VN are the amplitudes of the second
through Nth harmonics.
LTC2301
LTC2305
REFCOMP
+
10μF
0.1μF
GND
Internal Reference
The LTC2301/LTC2305 have an on-chip, temperature
compensated bandgap reference that is factory trimmed
to 2.5V (Refer to Figure 5a). It is internally connected
to a reference amplifier and is available at VREF (Pin 7).
VREF should be bypassed to GND with a 2.2μF tantalum
capacitor to minimize noise. An 8k resistor is in series
with the output so that it can be easily overdriven by an
external reference if more accuracy and/or lower drift are
required as shown in Figure 5b. The reference amplifier
gains the VREF voltage by 1.638 to 4.096V at REFCOMP.
To compensate the reference amplifier, bypass REFCOMP
with a 10μF ceramic or tantalum capacitor in parallel with
23015 F05b
Figure 5b. Using the LT1790A-2.5 as an External Reference
5V
0.1μF
VREF
VIN
LT1790A-4.096
VOUT
LTC2301
LTC2305
REFCOMP
+
10μF
0.1μF
GND
23015 F05c
Figure 5c. Overdriving REFCOMP Using the LT1790A-4.096
23015f
15
LTC2301/LTC2305
APPLICATIONS INFORMATION
Internal Conversion Clock
Start Condition
The internal conversion clock is factory trimmed to
achieve a typical conversion time (tCONV) of 1.3μs and a
maximum conversion time of 1.6μs over the full operating
temperature range.
I2C Interface
Stop Condition
SDA
S
SCL
SDA
SCL
P
23015 F06
Figure 6. Timing Diagrams of Start and Stop Conditions
I2C
inThe LTC2301/LTC2305 communicate through an
terface. The I2C interface is a 2-wire open-drain interface
supporting multiple devices and multiple masters on a
single bus. The connected devices can only pull the serial
data line (SDA) low and can never drive it high. SDA is
required to be externally connected to the supply through
a pull-up resistor. When the data line is not being driven
low, it is high. Data on the I2C bus can be transferred at
rates up to 100kbits/s in the standard mode and up to
400kbits/s in the fast mode.
Each device on the I2C bus is recognized by a unique
address stored in the device and can only operate either
as a transmitter or receiver, depending on the function of
the device. A device can also be considered as a master
or a slave when performing data transfers. A master is
the device which initiates a data transfer on the bus and
generates the clock signals to permit the transfer. Devices
addressed by the master are considered slaves.
The LTC2301/LTC2305 can only be addressed as slaves.
Once addressed, they can receive configuration bits (DIN
word) or transmit the last conversion result. The serial clock
line (SCL) is always an input to the LTC2301/LTC2305 and
the serial data line (SDA) is bidirectional. These devices
support the standard mode and the fast mode for data
transfer speeds up to 400kbits/s (see Timing Diagram
section for definition of the I2C timing).
The Start and Stop Conditions
Referring to Figure 6, a Start (S) condition is generated
by transitioning SDA from high to low while SCL is high.
The bus is considered to be busy after the Start condition.
When the data transfer is finished, a Stop (P) condition
is generated by transitioning SDA from low to high while
SCL is high. The bus is free after a Stop condition is generated. Start and Stop conditions are always generated
by the master.
When the bus is in use, it stays busy if a Repeated Start
(Sr) is generated instead of a Stop condition. The Repeated
Start timing is functionally identical to the Start and is
used for writing and reading from the device before the
initiation of a new conversion.
Data Transferring
After the Start condition, the I2C bus is busy and data
transfer can begin between the master and the addressed
slave. Data is transferred over the bus in groups of nine
bits, one byte followed by one acknowledge (ACK) bit.
The master releases the SDA line during the ninth SCL
clock cycle. The slave device can issue an ACK by pulling
SDA low or issue a Not Acknowledge (NAK) by leaving
the SDA line high impedance (the external pull-up resistor
will hold the line high). Change of data only occurs while
the SCL line is low.
Data Format
After a Start condition, the master sends a 7-bit address
followed by a read/write (R/W) bit. The R/W bit is 1 for
a read request and 0 for a write request. If the 7-bit
address matches one of the LTC2301/LTC2305’s 9 pinselectable addresses (see Table 2), the ADC is selected.
When the ADC is addressed during a conversion, it will
not acknowledge R/W requests and will issue a NAK by
leaving the SDA line high. If the conversion is complete,
the LTC2301/LTC2305 issues an ACK by pulling the SDA
line low. The LTC2301/LTC2305 has two registers. The
12-bit wide output register contains the last conversion
result. The 6-bit wide input register configures the input
MUX and the operating mode of the ADC.
23015f
16
LTC2301/LTC2305
APPLICATIONS INFORMATION
Output Data Format
The output register contains the last conversion result.
After each conversion is completed, the device automatically enters either nap or sleep mode depending on the
setting of the SLP bit (see Nap Mode and Sleep Mode
sections). When the LTC2301/LTC2305 is addressed for
a read operation, it acknowledges by pulling SDA low and
acts as a transmitter. The master/receiver can read up to
two bytes from the LTC2301/LTC2305. After a complete
read operation of 2 bytes, a Stop condition is needed to
initiate a new conversion. The device will NAK subsequent
read operations while a conversion is being performed.
The data output stream is 16 bits long and is shifted out
on the falling edges of SCL (see Figure 7a). The first bit
is the MSB and the 12th bit is the LSB of the conversion
1
2
3
4
5
6
7
8
9
result. The remaining four bits are zero. Figures 13 and 14
are the transfer characteristics for the bipolar and unipolar
modes. Data is output on the SDA line in 2’s complement
format for bipolar readings and in straight binary for
unipolar readings.
Input Data Format
When the LTC2301/LTC2305 is addressed for a write
operation, it acknowledges by pulling SDA low during
the low period before the 9th cycle and acts as a receiver.
The master/transmitter can then send 1 byte to program
the device. The input byte consists of the 6-bit DIN word
followed by two bits that are ignored by the ADC and are
considered don’t cares (X) (see Figure 7b). The input bits
are latched on the rising edge of SCL during the write
operation.
1
2
3
4
5
6
7
8
9
•••
SCL
SDA
A6
A5
A4
A3
A2
A1
A0
B11
R/W
START BY
MASTER
ACK BY
ADC
B10
B9
B8
B7
B6
B5
•••
B4
ACK BY
MASTER
MOST SIGNIFICANT DATA BYTE
ADDRESS FRAME
READ 1 BYTE
1
SCL
(CONTINUED)
2
3
4
5
6
7
8
9
•••
CONVERSION
INITIATED
SDA
(CONTINUED)
•••
B3
B2
B1
STOP
BY MASTER
B0
NAK BY
MASTER
LEAST SIGNIFICANT DATA BYTE
READ 1 BYTE
23015 F07a
Figure 7a. Timing Diagram for Reading from the LTC2301/LTC2305
NOTE: S/D BIT IS A DON’T CARE (X) FOR THE LTC2301
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
SCL
CONVERSION
INITIATED
SDA
A6
A5
A4
A3
A2
A1
START BY
MASTER
A0
S/D
R/W
ACK BY
ADC
ADDRESS FRAME
O/S
X
X
UNI
SLP
X
DIN WORD
WRITE 1 BYTE
X
ACK BY
ADC
STOP BY
MASTER
23015 F07b
Figure 7b. Timing Diagram for Writing to the LTC2301/LTC2305
23015f
17
LTC2301/LTC2305
APPLICATIONS INFORMATION
After power-up, the ADC initiates an internal reset cycle
which sets the DIN word to all 0s (S/D=O/S=UNI=SLP=0).
A write operation may be performed if the default state
of the ADC’s configuration is not desired. Otherwise, the
ADC must be properly addressed and followed by a Stop
condition to initiate a conversion.
Table 2. Address Assignment
Initiating a New Conversion
The LTC2301/LTC2305 awakens from either nap or sleep
when properly addressed for a read/write operation. A
Stop command may then be issued after performing the
read/write operation to trigger a new conversion.
The LTC2301/LTC2305 have two address pins (AD0 and
AD1) that may be tied high, low or left floating to enable
one of the 9 possible addresses (see Table 2).
In addition to the configurable addresses listed in Table 2,
the LTC2301/LTC2305 also contain a global address
(1110111) which may be used for synchronizing multiple
LTC2301/LTC2305s or other I2C LTC230X SAR ADCs (see
Synchronizing Multiple LTC2301/LTC2305s with Global
Address Call section).
CONVERSION
NAP
R
ACK
READ
DATA OUTPUT
P
ADDRESS
LOW
LOW
0001000
LOW
FLOAT
0001001
LOW
HIGH
0001010
FLOAT
HIGH
0001011
FLOAT
FLOAT
0011000
FLOAT
LOW
0011001
HIGH
LOW
0011010
HIGH
FLOAT
0011011
HIGH
HIGH
0101000
In applications where the same input channel is sampled
each cycle, conversions can be continuously performed
and read without a write cycle (see Figure 8). The DIN word
remains unchanged from the last value written into the
device. If the device has not been written to since powerup, the DIN word defaults to all 0s (S/D=O/S=UNI=SLP=0).
At the end of a read operation, a Stop condition may be
given to start a new conversion. At the conclusion of the
conversion cycle, the next result may be read using the
method described above. If the conversion cycle is not
concluded and a valid address selects the device, the
LTC2301/LTC2305 generates a NAK signal indicating the
conversion cycle is in progress.
LTC2301/LTC2305 Address
7-BIT ADDRESS
AD0
Continuous Read
Issuing a Stop command after the 8th SCL clock pulse of
the address frame and before the completion of a read/write
operation will also initiate new conversion, but the output
result may not be valid due to lack of adequate acquisition
time (see Acquisition section).
S
AD1
S
CONVERSION
7-BIT ADDRESS
R
NAP
ACK
READ
DATA
OUTPUT
P
CONVERSION
23015 F08
Figure 8. Consecutive Reading with the Same Configuration
23015f
18
LTC2301/LTC2305
APPLICATIONS INFORMATION
Continuous Read/Write
Once the conversion cycle is complete, the LTC2301/
LTC2305 can be written to and then read from using the
Repeated Start (Sr) command. Figure 9 shows a cycle which
begins with a data Write, a repeated Start, followed by a
Read and concluded with a Stop command. The following
conversion begins after all 16 bits are read out of the device
or after a Stop command. The following conversion will
be performed using the newly programmed data.
Nap Mode
Synchronizing Multiple LTC2301/LTC2305s with a
Global Address Call
In applications where several LTC2301/LTC2305s or other
I2C SAR ADCs from Linear Technology Corporation are
used on the same I2C bus, all converters can be synchronized through the use of a global address call. Prior to
issuing the global address call, all converters must have
completed a conversion cycle. The master then issues a
Start, followed by the global address 1110111, and a write
request. All converters will be selected and acknowledge
S
7-BIT ADDRESS
CONVERSION
NAP
W
ACK
WRITE
the request. The master then sends a write byte (optional)
followed by the Stop command. This will update the
channel selection (optional) and simultaneously initiate
a conversion for all ADCs on the bus (see Figure 10).
In order to synchronize multiple converters without changing the channel, a Stop command may be issued after
acknowledgement of the global write command. Global
read commands are not allowed and the converters will
NAK a global read request.
Sr
DATA OUTPUT
The ADCs enter nap mode after a conversion is complete
(tCONV) if the SLP bit is set to a logic 0. The supply current
decreases to 225μA in nap mode between conversions,
thereby reducing the average power dissipation as the
sample rate decreases. For example, the LTC2301/LTC2305
draw an average of 300μA at a 1ksps sampling rate. The
LTC2301/LTC2305 keep only the reference (VREF) and
reference buffer (REFCOMP) circuitry active when in nap
mode.
7-BIT ADDRESS
CONVERSION
R
ACK
READ
DATA
OUTPUT
P
CONVERSION
23015 F09
Figure 9. Write, Read, Start Conversion
SCL
SDA
S
CONVERSION
LTC2301/LTC2305
LTC2301/LTC2305
GLOBAL ADDRESS
W
NAP
ACK
LTC2301/LTC2305
WRITE (OPTIONAL)
DATA OUTPUT
P
CONVERSION OF ALL LTC2301/05s
23015 F10
Figure 10. Synchronize Multiple LTC2301/LTC2305s with a Global Address Call
23015f
19
LTC2301/LTC2305
APPLICATIONS INFORMATION
Sleep Mode
performed, acquisition of the input signal begins on the
rising edge of the 9th clock pulse following the address
frame as shown in Figure 12a.
The ADCs enter sleep mode after a conversion is complete
(tCONV) if the SLP bit is set to a logic 1. The ADCs draw
only 7μA in sleep mode, provided that none of the digital
inputs are switching. When the LTC2301/LTC2305 are
properly addressed, the ADCs are released from sleep
mode and require 200ms (tREFWAKE) to wake up and charge
the respective 2.2μF and 10μF bypass capacitors on the
VREF and REFCOMP pins. A new conversion should not
be initiated before this time as shown in Figure 11.
If a write operation is being performed, acquisition of the
input signal begins on the falling edge of the sixth clock
cycle after the DIN word has been shifted in as shown in
Figure 12b. The LTC2301/LTC2305 will acquire the signal
from the input channel that was most recently programmed
by the DIN word. A minimum of 240ns is required to acquire
the input signal before initiating a new conversion.
Acquisition
Board Layout and Bypassing
The LTC2301/LTC2305 begin acquiring the input signal at
different instances depending on whether a read or write
operation is being performed. If a read operation is being
To obtain the best performance, a printed circuit board with
a solid ground plane is required. Layout for the printed
board should ensure digital and analog signal lines are
S
7-BIT ADDRESS
CONVERSION
R/W
ACK
SLEEP
P
tREFWAKE
CONVERSION
23015 F11
Figure 11. Exiting Sleep Mode and Starting a New Conversion
1
2
3
4
5
6
7
8
9
1
2
SCL
ACQUISITION BEGINS
SDA
A6
A5
A4
A3
A2
A1
A0
R/W
B11
tACQ
B10
23015 F12a
Figure 12a. Timing Diagram Showing Acquisition During a Read Operation
5
6
7
8
9
1
2
3
4
5
6
7
8
9
SCL
ACQUISITION BEGINS
SDA
A2
A1
A0
R/W
S/D
O/S
X
X
UNI SLP
X
X
tACQ
23015 F12b
Figure 12b. Timing Diagram Showing Acquisition During a Write Operation
23015f
20
LTC2301/LTC2305
APPLICATIONS INFORMATION
for the common return of these bypass capacitors is essential to the low noise operation of the ADC. These traces
should be as wide as possible. See Figure 15a–15e for a
suggested layout.
111...111
011...111
BIPOLAR
ZERO
011...110
111...110
000...001
OUTPUT CODE
OUTPUT CODE (TWO’S COMPLEMENT)
separated as much as possible. Care should be taken not
to run any digital signals alongside an analog signal. All
analog inputs should be shielded by GND. VREF, REFCOMP
and VDD should be bypassed to the ground plane as close
to the pin as possible. Maintaining a low impedance path
000...000
111...111
111...110
FS = 4.096V
1LSB = FS/2n
1LSB = 1mV
100...001
100...000
–FS/2
–1 0V 1
LSB
LSB
INPUT VOLTAGE (V)
100...001
100...000
011...111 UNIPOLAR
ZERO
011...110
FS = 4.096V
1LSB = FS/2n
1LSB = 1mV
000...001
000...000
FS/2 – 1LSB
0V
FS – 1LSB
INPUT VOLTAGE (V)
23015 F13
Figure 13. Bipolar Transfer Characteristics (2’s Complement)
23015 F14
Figure 14. Unipolar Transfer Characteristics (Straight Binary)
Figure 15a. Top Silkscreen
23015f
21
LTC2301/LTC2305
APPLICATIONS INFORMATION
Figure 15b. Topside
Figure 15c. Layer 2 Ground Plane
Figure 15d. Layer 3 Power Plane
Figure 15e. Bottomside
23015f
22
LTC2301/LTC2305
PACKAGE DESCRIPTION
DE/UE Package
12-Lead Plastic DFN (4mm × 3mm)
(Reference LTC DWG # 05-08-1695)
4.00 ±0.10
(2 SIDES)
7
0.70 ±0.05
3.60 ±0.05
2.20 ±0.05
0.40 ± 0.10
12
R = 0.05
TYP
3.30 ±0.05
1.70 ± 0.05
PACKAGE
OUTLINE
0.25 ± 0.05
R = 0.115
TYP
PIN 1
TOP MARK
(NOTE 6)
0.200 REF
0.50 BSC
3.30 ±0.10
3.00 ±0.10
(2 SIDES)
1.70 ± 0.10
0.75 ±0.05
6
0.25 ± 0.05
1
PIN 1 NOTCH
R = 0.20 OR
0.35 × 45°
CHAMFER
(UE12/DE12) DFN 0806 REV D
0.50 BSC
2.50 REF
2.50 REF
0.00 – 0.05
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING PROPOSED TO BE A VARIATION OF VERSION
(WGED) IN JEDEC PACKAGE OUTLINE M0-229
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
MS Package
12-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1668 Rev Ø)
0.889 p 0.127
(.035 p .005)
5.23
(.206)
MIN
3.20 – 3.45
(.126 – .136)
4.039 p 0.102
(.159 p .004)
(NOTE 3)
0.65
(.0256)
BSC
0.42 p 0.038
(.0165 p .0015)
TYP
12 11 10 9 8 7
RECOMMENDED SOLDER PAD LAYOUT
0.254
(.010)
DETAIL “A”
3.00 p 0.102
(.118 p .004)
(NOTE 4)
4.90 p 0.152
(.193 p .006)
0o – 6o TYP
0.406 p 0.076
(.016 p .003)
REF
GAUGE PLANE
0.53 p 0.152
(.021 p .006)
DETAIL “A”
0.18
(.007)
SEATING
PLANE
1.10
(.043)
MAX
0.22 – 0.38
(.009 – .015)
TYP
1 2 3 4 5 6
0.650
(.0256)
BSC
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
0.86
(.034)
REF
0.1016 p 0.0508
(.004 p .002)
MSOP (MS12) 1107 REV Ø
23015f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
23
LTC2301/LTC2305
TYPICAL APPLICATION
Driving the LTC2305 with ±10V Input Signals Using a Precision Attenuator
5V
IN
OUT
LT1790-2.5
0.1μF
1μF
5V
GND
10V
10μF
0.1μF
7
8
450k
50k
9 150k
10
1.7k
1.7k
LTC2305
–
450k
1 450k
AD1 AD0
VDD
+
4pF
LT1991
6 100Ω
CH0
47pF
CH1
450k
ANALOG
INPUT
MUX
+
–
SCL
I2C
PORT
12-BIT
SAR ADC
CONTROL
LOGIC
(FPGA, CPLD,
DSP, ETC)
SDA
2 150k
±10V
INPUT
SIGNAL
3
50k
4pF
4
INTERNAL
2.5V REF
5
VREF
2.2μF
–10V
REFCOMP
GND
0.1μF
10μF
23015 TA02
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC1417
14-Bit, 400ksps Serial ADC
20mW, Unipolar or Bipolar, Internal Reference, SSOP-16 Package
LTC1468/LT1469
Single/Dual 90MHz, 22V/μs, 16-Bit Accurate Op Amps Low Input Offset: 75μV/125μV
LTC1609
16-Bit, 200ksps Serial ADC
65mW, Configurable Bipolar and Unipolar Input Ranges, 5V Supply
LTC1790
Micropower Low Dropout Reference
60μA Supply Current, 10ppm/°C, SOT-23 Package
LTC1850/LTC1851
10-Bit/12-Bit, 8-Channel, 1.25Msps ADC
Parallel Output, Programmable MUX and Sequencer, 5V Supply
LTC1852/LTC1853
10-Bit/12-Bit, 8-Channel, 400ksps ADC
Parallel Output, Programmable MUX and Sequencer, 3V or 5V Supply
LTC1860/LTC1861
12-Bit, 1-/2-Channel 250ksps ADC in MSOP
850μA at 250ksps, 2μA at 1ksps, SO-8 and MSOP Packages
LTC1860L/LTC1861L 3V, 12-Bit, 1-/2-Channel 150ksps ADC
450μA at 150ksps, 10μA at 1ksps, SO-8 and MSOP Packages
LTC1863/LTC1867
6.5mW, Unipolar or Bipolar, Internal Reference, SSOP-16 Package
12-/16-Bit, 8-Channel 200ksps ADC
LTC1863L/LTC1867L 3V, 12-/16-Bit, 8-Channel 175ksps ADC
2mW, Unipolar or Bipolar, Internal Reference, SSOP-16 Package
LTC1864/LTC1865
850μA at 250ksps, 2μA at 1ksps, SO-8 and MSOP Packages
16-Bit, 1-/2-Channel 250ksps ADC in MSOP
LTC1864L/LTC1865L 3V, 16-Bit, 1-/2-Channel 150ksps ADC in MSOP
450μA at 150ksps, 10μA at 1ksps, SO-8 and MSOP Packages
LTC2302/LTC2306
12-Bit, 1-/2-Channel 500ksps SPI ADCs in
3mm × 3mm DFN
14mW at 500ksps, Single 5V Supply, Software Compatible with LTC2308
LTC2308
12-Bit, 8-Channel 500ksps SPI ADC
5V, Internal Reference, 4mm × 4mm QFN Package, Software Compatible
with LTC2302/LTC2306
LTC2309
12-Bit, 8-Channel ADC with I2C Interface
5V, Internal Reference, 4mm × 4mm QFN and 20-Pin TSSOP Packages,
Software Compatible with LTC2301/LTC2305
LTC2451/LTC2453
Easy-to-Use, Ultra-Tiny 16-Bit I2C Delta Sigma ADCs
2 LSB INL, 50nA Sleep Current, 60Hz Output Rate, 3mm × 2mm DFN
Package, Single-Ended/Differential Inputs
LTC2487/LTC2489/
LTC2493
2-/4-Channel Easy Drive I2C Delta Sigma ADCs
16-/24-Bits, PGA and Temp Sensor, 4mm × 3mm DFN Packages
LTC2495/LTC2497/
LTC2499
8-/16-Channel Easy Drive I2C Delta Sigma ADCs
16-/24-Bits, PGA and Temp Sensor, 5mm × 7mm QFN Packages
23015f
24 Linear Technology Corporation
LT 0808 • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2008