PanelMatch™ I N T E G R A T E D LXM1623-12-6x 12V Dual 6W Programmable CCFL Inverter Module P R O D U C T S P ODUCTION D ATASHEET KEY FEATURES DESCRIPTION Externally Programmable Maximum Output Current Easy to Use Brightness Control RangeMAX Wide Range Dimming Output Open/Short-Circuit Protection and Automatic StrikeVoltage Regulation and Timeout Fixed Frequency Operation Rated From -20 to 70°C UL60950 E175910 The resultant “burst drive” that energizes the lamp was designed specifically to ensure that no premature lamp degradation occurs, while allowing significant power savings at lower dim levels. The modules convert DC voltage from the system battery or AC adapter directly to high frequency, high-voltage waves required to ignite and operate CCFL lamps. A 5V input inverter is also available (LXM1623-05-6x), as well as 4W versions (LXM1623-xx-4x) for driving smaller lower voltage panels. The modules design is based on Microsemi’s new LX1689 backlight controller, which provides a number of cost and performance advantages due to the controller’s high level of integration. Other benefits of this new topology are stable fixed-frequency operation, secondary-side strike-voltage regulation and both open/shorted lamp protection with fault timeout. APPLICATIONS WWW . Microsemi .C OM The LXM1623-12-6x is a Dual 6W Output Direct Drive™ CCFL (Cold Cathode Fluorescent Lamp) Inverter Module specifically designed for driving LCD backlight lamps. It is ideal for driving typical 10.4” to 15” TFT panels. LXM1623 modules provide the designer with a vastly superior display brightness range. This brightness range is achievable with virtually any LCD display. The modules are available with a dimming input that permits brightness control from either a DC voltage source or a PWM signal or external Potentiometer. The maximum output current is externally programmable over a range of 5 to 8mA in 1mA steps to allow the inverter to properly match to a wide array of LCD panel lamp current specifications. RangeMAX Digital Dimming Technique provides flicker-free brightness control in any wide range typically (50:1+) dimming application. High Brightness Displays Portable Instrumentation Desktop Displays Industrial Display Controls BENEFITS Smooth, Flicker Free 2%100% Full-Range Brightness Control Programmable output current allows inverter to mate with a wide variety of LCD panel’s specifications Output Open Circuit Voltage Regulation Minimizes Corona Discharge For High Reliability IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com PRODUCT HIGHLIGHT U D N IV E R S A L "P W M ", V , IN IM M IN G P O R P U T O T E N T IO M E T E R PW M S ig n a l 1 3 P o te n tio m e te r 2 2 D C V o lta g e S o u rc e D C W 1 3 E L E C T A B L E M O A X IM U M T O 8 M A U T P U T C U R R E N T 5 M LXM1623-12-6X S W A R M S PACKAGE ORDER INFO Copyright 2002 Rev. 1.0, 2003-11-26 PART NUMBER OUTPUT CONNECTOR LXM1623-12-61 LXM1623-12-62 LXM1623-12-63 JST SM02(8.0)B-BHS-1-TB JST SM02B-BHSS-1-TB Honda QZ-19-A3MYL #02 INVERTER MATES DIRECTLY TO PANEL CONNECTORS JST BHR-03VS-1 JST BHSR-02VS-1 HONDA QZ-19-3F01 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 1 PanelMatch™ I N T E G R A T E D LXM1623-12-6x 12V Dual 6W Programmable CCFL Inverter Module P R O D U C T S P ODUCTION D ATASHEET Input Signal Voltage (VIN1).....................................................................................................................................-0.3V to 15V Input Power ....................................................................................................................................................................... 15W Output Voltage, no load ............................................................................................................ Internally Limited to 1800VRMS Output Current ............................................................................................................................9.5mARMS (Internally Limited) Output Power (each output) ............................................................................................................................................. 6.0W Input Signal Voltage ( SLEEP Input) ..................................................................................................................... -0.3V to VIN1 Input Signal Voltage (BRITE) ...............................................................................................................................-0.3V to 5.5V Ambient Operating Temperature, zero airflow.....................................................................................................-20°C to 70°C Operating Relative Humidity, non-condensing ................................................................................................................ ≤ 90% Storage Temperature Range...............................................................................................................................-40°C to 85°C Note 1: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified terminal. WWW . Microsemi .C OM ABSOLUTE MAXIMUM RATINGS (NOTE 1) RECOMMENDED OPERATING CONDITIONS (R.C.) This module has been designed to operate over a wide range of input and output conditions. However, best efficiency and performance will be obtained if the module is operated under the condition listed in the ‘R.C.’ column. Min. and Max. columns indicate values beyond which the inverter, although operational, will not function optimally. Parameter Symbol Input Supply Voltage Range (Fully Regulated Lamp Current) Input Supply Voltage Range (Functional) Output Power (each output) Linear BRITE Control Input Voltage Range Lamp Operating Voltage Lamp Current (Full Brightness) Operating Ambient Temperature Range VIN1 PO VBRT_ADJ VLAMP IOLAMP TA Recommended Operating Conditions Min R.C. Max 10.8 12 13.2 10.2 12 5.5 13.8 6.0 2.0 720 8 70 0.5 480 5 -20 600 Units V W V VRMS mARMS °C ELECTRICAL CHARACTERISTICS Unless otherwise specified, the following specifications apply over the recommended operating condition and ambient temperature of 25°C except where otherwise noted. Parameter ` Symbol Test Conditions LXM1623-12-6x Min Typ Max Units OUTPUT PIN CHARACTERISTICS IL(MAX) Full Bright Lamp Current (each output) IL(MAX) Full Bright Lamp Current (each output) IL(MAX) Full Bright Lamp Current (each output) IL(MAX) Output Current Lamp to Lamp Deviation ILL%DEV Min. Average Lamp Current (each output) Lamp Start Voltage Operating Frequency Burst Frequency Copyright 2002 Rev. 1.0, 2003-11-26 IL(MIN) VLS fO fBURST VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC ISET1 = Ground, ISET2 = Ground VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC ISET1 = Ground, ISET2 = Open VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC ISET1 = Open, ISET2 = Ground VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC ISET1 = Open, ISET2 = Open VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC ISET1 = Open, ISET2 = Open VBRT_ADJ ≤0.5VDC, SLEEP > 2.0V, VIN1 = 12VDC ISET1 = ISET2 = Ground -20°C < TA < 70°C, VIN1 > 10.8VDC VBRT_ADJ = 2.5VDC, SLEEP > 2.0V, VIN1 = 12V Output Burst Frequency 4.4 5 5.6 mARMS 5.4 6 6.6 mARMS 6.4 7 7.6 mARMS 7.4 8 8.6 mARMS 3 10 % 0.30 mARMS 1400 1650 66 70 73 kHz 257 273 286 Hz Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 VRMS Page 2 ELECTRICALS Full Bright Lamp Current (each output) PanelMatch™ I N T E G R A T E D P R O D U C T S LXM1623-12-6x 12V Dual 6W Programmable CCFL Inverter Module P ODUCTION D ATASHEET Parameter ` Symbol ` ` LXM1623-12-6x Min Typ Max Units -300 50 µADC µADC BRITE INPUT Input Current ` Test Conditions IBRT VBRT_ADJ = 0VDC VBRT_ADJ = 3VDC Minimum Input for Max. Lamp Current VBRT_ADJ IO(LAMP) = Maximum Lamp Current Maximum Input for Min. Lamp Current VBRT_ADJ IO(LAMP) = Minimum Lamp Current 2.0 0.4 2.05 0.5 VDC VDC SLEEP INPUT RUN Mode VSLEEP 2.0 VIN1 VDC SLEEP Mode VSLEEP -0.3 0.8 VDC 0.4 V WWW . Microsemi .C OM ELECTRICAL CHARACTERISTICS (CONTINUED) Unless otherwise specified, the following specifications apply over the recommended operating condition and ambient temperature of 25°C except where otherwise noted. SET1,2 INPUT SET1,2 Low Threshold VL Input Current ISET VSET ≤ 0.4V -300 µA POWER CHARACTERISTICS Sleep Current IIN(MIN) Run Current IIN(RUN) η Efficiency VIN1 = 12VDC, SLEEP < 0.8V 0.0 VIN1 = 12VDC, SLEEP ≥ 2.0V, ISET1 = Open ISET2 = Ground, VLAMP = 600VRMS VIN1 = 12VDC, SLEEP ≥ 2.0V, ISET1 = Open ISET2 = Ground, VLAMP = 600VRMS 10 30 µADC 875 mADC 85 % FUNCTIONAL PIN DESCRIPTION CONN PIN DESCRIPTION CN1 (Molex 53261-0890) Mates with 51021-0800 housing, 50079-8100 pins. Mates with LX9501 input cable assembly CN1-1 CN1-2 CN1-3 CN1-4 VIN1 Main Input Power Supply (10.8V < VIN1 < 13.2V) GND Power Supply Return CN1-5 SLEEP CN1-6 BRITE CN1-7 SET1 SET1 MSB Connecting this pin to ground decreases the output current (see Table 1) CN1-8 SET2 SET2 LSB Connecting this pin to ground decreases the output current (see Table 1) ON/OFF Control. (0V < SLEEP < 0.8 = OFF, SLEEP >= 2.0V = ON Brightness Control (0.5V to 2.0VDC). 2.0VDC gives maximum lamp current. CN2-1 CN3-1 VHI High voltage connection to high Side of lamp. Connect to lamp terminal with shortest lead length. DO NOT connect to Ground. CN2-2 CN3-2 VLO Connection to low side of lamp. Connect to lamp terminal with longer lead length. DO NOT connect to Ground CN2, CN3 for LXM1623-12-63 (Honda QZ-19-A3MYL #02) CN2-3 CN3-3 VHI High voltage connection to high side of lamp. Connect to lamp terminal with shortest lead length. DO NOT connect to Ground. CN2-1 CN3-1 VLO Connection to low side of lamp. Connect to lamp terminal with longer lead length. DO NOT connect to Ground Copyright 2002 Rev. 1.0, 2003-11-26 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 3 ELECTRICALS CN2, CN3 for LXM1623-12-61 and -62 (JST SM02(8.0)B-BHS-1-TB or SM02B-BHSS-1-TB) PanelMatch™ I N T E G R A T E D LXM1623-12-6x 12V Dual 6W Programmable CCFL Inverter Module P R O D U C T S P ODUCTION D ATASHEET WWW . Microsemi .C OM TABLE 1 OUTPUT CURRENT SETTINGS SET1 (Pin 7) Open* Open* Ground Ground SET2 (Pin 8) Open* Ground Open* Ground Nominal Output Current 8.0mA 7.0mA 6.0mA 5.0mA * If driven by a logic signal it should be open collector or open drain only, not a voltage source. PHYSICAL DIMENSIONS LXM1623-12-6X GROUNDED MOUNTING HOLE 3MM ±.08 DIA. 6MM HEAD CLEARANCE BOTH HOLES -01 6.4 in. W 165mm SM02(8.0)B-BHS-1-TB (JST) 5.9 in. 151mm W .118 in 0.827in CN-2 3mm CN-3 21mm .708 in 18mm .551 in 14mm -03 MOUNTING HOLE 3MM ±.08 DIA. 0.0395 in Honda QZ-19-A3MYL #02 1mm 0.295in -02 SM02B-BHSS-1-TB (JST) Warning 7.5mm Max weight: 20g PCB tolerances ± 0.5mm , 4-40 recommended mounting screws High Voltage Present at high side of Transformers and Output Connectors SIMPLIFIED BLOCK DIAGRAM +3V High Voltage Transform er V BRIT E 10K Comparator + 0.5 2V DC Ramp - Ram p Gen V IN1 PACKAGE DATA +3V Transform er Driver V HI LAMP Controller OC SENSE 10K SET 1 SET 2 +3V OV SENSE 10K I SENSE V LO One of two Copyright 2002 Rev. 1.0, 2003-11-26 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 4 PanelMatch™ I N T E G R A T E D P R O D U C T S LXM1623-12-6x 12V Dual 6W Programmable CCFL Inverter Module P ODUCTION D ATASHEET 12V DAC or Pot The brightness control may be a voltage output DAC or other voltage source, a digital pot or 20K manual pot. The inverter contains an internal 10K pull-up to 3V to bias the pot, add a 1.8K resistor to set the lower threshold voltage. A 3.3V Logic Level PWM signal from a micro-controller may also be used as shown in Figure 1A. 0.45V 20K to 2.0V If you need to turn the inverter ON/OFF remotely, connect to TTL logic signal to the SLEEP input. Connect VHI to high voltage wire from the lamp. Connect VLO to the low voltage wire (wire with thinner insulation). Never connect VLO to circuit ground as this will defeat lamp current regulation. If both lamp wires have heavy high voltage insulation, connect the longest wire to VLO. This wire is typically white. Use the SET1 and SET2 (see Figure 2) inputs to select the desired maximum output current. Using these two pins in combination allows the inverter to match a wide variety of panels from different manufactures. Generally the best lamp lifetime correlates with driving the CCFL at the manufactures nominal current setting. However the SET1 and SET2 inputs allow the user the flexibility to adjust the current to the maximum allowable output current to increase panel brightness at the expense of some reduced lamp life. Although the SET pins are designed such that just leaving them open or grounding them is all that is needed to set the output current, they can also be actively set. Using a open collector or open drain logic signal will allow you to reduce the lamp current for situations where greater dim range is required, as an example in nighttime situations. In conjunction with a light sensor or other timer the panel could be set to higher brightness (maximum output current) for daytime illumination and lower brightness (minimum or typical output current) at nighttime. Since the dim ratio is a factor of both the burst duty cycle and the peak output current, using this technique the effective dim ratio can be increased greater than the burst duty cycle alone. Conversely the SET inputs could be used to overdrive the lamp temporarily to facilitate faster lamp warm up at initial lamp turn on. Of course any possible degradation on lamp life from such practices is the users responsibility since not all lamps are designed to be overdriven. The inverter has a built in fault timeout function. If the output is open (lamp disconnected or broken) or shorted the inverter will attempt to strike the lamp for several seconds. After about 2 to 4 seconds without success the inverter will shutdown. In order to restart the inverter it is necessary to toggle the sleep input or cycle the VIN1 input supply V HI LXM1623-12-6x 1.8K SLEEP SET 1 SET 2 CCFL TUBE GND V LO NC NC ONE OF TW O Figure 1 – Brightness Control (Output current set to maximum) PW M Signal from System BRITE P.W . LXM1643-12-6x 10us to 125uS 0 < P.W. < 100% of period Figure 1A – PWM Brightness Control 12V V IN1 BRITE V HI CCFL TUBE LXM1623-12-6x SLEEP SET 1 SET 2 GND V LO ONE OF TW O L L H H L 5.0mARMS H 6.0mARMS L 7.0mARMS H 8.0mARMS L=GND; H=Open Figure 2 – Max Output Current (SET1 and SET2 Inputs) Copyright 2002 Rev. 1.0, 2003-11-26 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 5 APPLICATION V IN1 BRITE WWW . Microsemi .C OM TYPICAL APPLICATION PanelMatch™ I N T E G R A T E D P R O D U C T S LXM1623-12-6x 12V Dual 6W Programmable CCFL Inverter Module P ODUCTION D ATASHEET NOTES WWW . Microsemi .C OM NOTES Preliminary Data – Information contained in this document is pre-production data and is proprietary to Microsemi. It may not be modified in any way without the express written consent of Microsemi. Product referred to herein is offered in sample form only and Microsemi reserves the right to change or discontinue this proposed product at any time. Copyright 2002 Rev. 1.0, 2003-11-26 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 6