NKK M2037TNW Miniature rocker Datasheet

Miniature Rockers
Series M
Distinctive Characteristics
Three methods of panel mounting: flat frame for flush with face or subpanel,
snap-in, and PCB.
High insulating barriers increase isolation of circuits in multipole devices
and provide added protection to contact points.
The molded diallyl phthalate case has a UL 94V-0
flammability rating.
Epoxy sealed terminals prevent entry of solder flux
and other contaminants.
Prominent external insulating barriers increase
insulation resistance and dielectric strength.
Bias guard prevents misalignment of contacts;
interlocking of actuator block with rocker and
internal guide does not allow transmission of
diagonal force on rocker to reach contact
mechanism.
Clinching of the frame to the case well above the base and
terminals provides 1,500V dielectric strength.
Actual Size
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Miniature Rockers
Series M
General Specifications
Electrical Capacity (Resistive Load)
Power Level (code W):
Logic Level (code G):
Logic/Power Level (code A):
6A @ 125V AC & 3A @ 250V AC
4A @ 30V DC for On-None-On; 3A @ 30V DC for all other circuits
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Combines W & G ratings
Note: Find additional explanation of dual rating & operating range in Supplement section.
Other Ratings
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Angle of Throw:
10 milliohms maximum for silver; 20 milliohms maximum for gold
1,000 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts and case for 1 minute minimum
50,000 operations minimum
25,000 operations minimum for silver; 50,000 operations minimum for gold;
50,000 operations minimum for silver at 3A @ 125V AC
25°
Materials & Finishes
Actuator Clip & Mounting Frame:
Body Frame:
Case:
Movable Contactor:
Movable Contacts:
Stationary Contacts:
Terminals:
Stainless Steel
Stainless steel
Diallyl phthalate resin (UL94V–0)
Phosphor bronze with silver or gold plating
Silver alloy (code W); copper with gold plating (code G); or
silver alloy with gold plating (code A)
Silver with silver plating (code W); copper or brass with gold plating (code G);
or silver with gold plating (code A)
Copper or brass with silver plating; or copper or brass with gold plating
Environmental Data
Operating Temp Range:
Humidity:
Vibration:
Shock:
Processing
Soldering:
Cleaning:
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Wave Soldering (PC version) for Gold: See Profile A in Supplement section.
Manual Soldering for Gold: See Profile A in Supplement section.
Wave Soldering (PC version) for Silver: See Profile B in Supplement section.
Manual Soldering for Silver: See Profile B in Supplement section.
Note: Actuator must be in OFF (center) position while soldering.
These devices are not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications
Flammability Standards:
UL Recognized:
CSA Certified:
UL94V–0 for case
All models recognized at 6A @ 125V AC or 3A @ 250V AC or
0.4VA maximum @ 28V DC maximum; UL File No. WOYR2.E44145;
add “/U” to end of part number to order UL mark on switch.
All models recognized at 6A @ 125V AC or 3A @ 250V AC or
0.4VA maximum @ 28V maximum; CSA File No. 023535-0-000;
add “/C” to end of part number to order CSA mark on switch.
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Series M
Flat Frame Mount Miniature Rockers
TYPICAL SWITCH ORDERING EXAMPLE
M20
1
2
POLES
1
SPDT
2
DPDT
SP3T
3
3PDT
4
4PDT
DP3T
W
TN
01
.272” (6.9mm) Wide
Flat Frame
TY
.504” (12.8mm) Wide
Flat Frame
Small Actuators (TN Frame)
CONTACT MATERIALS
& RATINGS
W
Silver; Rated 6A @ 125V
AC & 3A @ 250V AC
G
Gold; Rated 0.4VA max @
28V AC/DC max
A
Gold over Silver; Rated
6A @ 125V AC & 0.4VA
max @ 28V AC/DC max
C
ROCKERS & PADDLES
MOUNTING FRAMES
TN
D
D
.365” (9.27mm)
Wide Rocker
E
.365” (9.27mm)
Wide Paddle
F
.450” (11.43mm)
Wide Rocker
G
.450” (11.43mm)
Wide Paddle
Large Actuators (TY Frame)
J
.595” (15.11mm)
Wide Rocker
H
.595” (15.11mm)
Wide Paddle
CIRCUITS
2
ON
NONE
ON
3
ON
OFF
ON
5
ON
NONE
(ON)
8
(ON)
OFF
(ON)
9
ON
OFF
(ON)
*4
ON
ON
ON
*6
(ON)
ON
(ON)
*7
ON
ON
(ON)
TERMINALS
01
Solder Lug
03
.250” (6.35mm)
Straight PC
ROCKER & PADDLE
COLORS
IMPORTANT:
Switches are supplied without UL
& CSA marking unless specified.
Specific models & ratings noted on
General Specifications page.
( ) = Momentary
* 3-ON circuits
A
Black
B
White
C
Red
E
Yellow
F
Green
G
Blue
H
Gray
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
M2012TNW01-DC
Red .365” (9.27mm)
Wide Rocker
.272” (6.9mm) Wide Flat Frame
SPDT ON-NONE-ON Circuit
Silver Contacts with 6-Amp Rating
Solder Lug Terminals
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Series M
Flat Frame Mount Miniature Rockers
POLES & CIRCUITS
Rocker Position
) = Momentary
(
Connected Terminals
Down
Center
Up
Pole
Model
SP
M2012
M2013
M2015
M2018
M2019
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
M2022
M2023
M2025
M2028
M2029
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
M2032
M2033
M2035
M2038
M2039
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
M2042
M2043
M2045
M2048
M2049
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
DP
3P
4P
Down
Center
Throw & Schematics
Up
Note: Terminal numbers are
not actually on the switch.
SPDT
2-3
OPEN
2 (COM)
2-1
3
1
DPDT
2-3 5-6
OPEN
2
2-1 5-4
5
(COM)
3
1
6
4
3PDT
2-3 5-6
8-9
2
2-1 5-4
8-7
OPEN
5
3
1
(COM)
6
4
8
9
7
8
11
4PDT
2-3 5-6
8-9 11-12
2-1 5-4
8-7 11-10
OPEN
3
(COM)
5
2
1
9
4
6
7
12
10
For 3 Throw (3-On)
Pole
SP
Model
M2024
M2026
M2027
Down
Center
ON
(ON)
ON
ON
ON
ON
Up
Connected Terminals & Schematics
ON
(ON)
(ON)
1 (out)
3 4 (out) 6 (out)
1 (out)
2-3 5-6
DP
M2044
M2046
M2047
ON
(ON)
ON
The SP3T model utilizes a
double pole base.
External connection must be
made during field installation.
ON
ON
ON
External
Connection
2 (in)
5
ON
(ON)
(ON)
1 (out) 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out)
External
Conn
6
3
5
2
4
1
(out)
1 (out)
(out)
1 (out) 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out)
2-3 5-4
8-9 11-10
External connection must be
made during field installation.
External
Connection
8 (in)
11
External
Connection
2 (in)
5
3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out)
Common
(in)
3 4 (out) 6 (out)
2-1 5-4
External
Connection
8 (in)
11
The DP3T model utilizes a
four pole base.
(out)
1 (out)
3 4 (out) 6 (out)
2-3 5-4
External
Connection
2 (in)
5
External
Connection
8 (in)
11
2-3 5-6
8-9 11-12
External
Connection
2 (in)
5
External
Connection
5
2 (in)
External
Connection
5
2 (in)
2-1 5-4
8-7 11-10
(out)
External
Conn
Common
(in)
(out)
(out)
12
9
11
8
5
2
10
7
4
1
(out)
6
3
Common
(in)
(out)
(out)
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Flat Frame Mount Miniature Rockers
Series M
MOUNTING FRAMES
TN
.272” (6.9mm)
Wide Flat Frame
(6.9)
.272
(3.5)
.138
(29.5) (23.8)
1.161 .937
Mounting hardware kit HK-1, as shown on the
following page, must be ordered separately.
(0.6)
.024
(2.4) Dia Typ
.094
Small Actuators & Panel Cutouts for TN Frame (actuator details on the following pages)
AT4148
AT4149
AT4150
AT4151
(17.8)
.701
(23.8)
.937
(10.1)
.398
TY
(12.7)
.500
(23.8)
.937
(2.6) Dia Typ
.102
(12.4)
.490
(2.6) Dia Typ
.102
Large Actuators & Panel Cutout for TY Frame
(actuator details on the following pages)
.504” (12.8mm)
Wide Flat Frame
AT4156
AT4157
Mounting hardware kit HK-2, as shown on the
following page, must be ordered separately.
(12.8)
.504
(3.5)
.138
(28.5)
1.122
(34.9)
1.374
(41.3) (34.9)
1.626 1.374
(0.6)
.024
(3.2) Dia Typ
.126
(16.0)
.630
(3.5) Dia Typ
.138
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Flat Frame Mount Miniature Rockers
Series M
MOUNTING FRAMES (CONTINUED)
Face Panel Mounting
STANDOFF
LENGTH
Subpanel Mounting
Flat frame devices may
also be mounted to the
face panel. Standoffs
are used to recess the
actuator and achieve
an attractive front panel
appearance.
Optional Snap-in Panel Frames
Optional Hardware Kits
for Subpanel or Face Panel Mounting
Panel
Thickness
Frame
Standoff
Length
These devices are especially
designed for subpanel mounting.
When installed on a mounting
plate behind the panel, hardware
is completely concealed and
the front panel retains a clean,
attractive appearance.
Further
details are
shown in
the previous
bracketed
PC mount
subsection.
Hardware
Kit Number
TN Frame
.125” (3.175mm) .233” (5.918mm)
HK-1
TY Frame
.125” (3.175mm) .312” (7.925mm)
HK-2
Hardware kits include:
2 stainless steel screws, 2 hex nuts, 2 lockwashers, & 2 standoffs
AT064-1
AT064-2
AT065-1
AT065-2
CONTACT MATERIALS & RATINGS
W
Silver over Silver
G
Gold over Brass or Copper
Power Level
6A @ 125V AC & 3A @ 250V AC
Logic Level
0.4VA maximum @ 28V AC/DC maximum
Note: See Supplement section to find complete explanation of operating range.
A
Power Level
or Logic Level
Gold over Silver
6A @ 125V AC
or 0.4VA maximum @ 28V AC/DC maximum
Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within
the same application. See Supplement section to find complete explanation of dual rating and operating range.
TERMINALS
01
Solder Lug
(4.0)
.157
Epoxy Seal
(2.0)
.079
(2.0)
(1.1) .079
.043
Thk = (0.8)
.031
03
.250” (6.35mm)
Straight PC
(4.8)
.189
3
2
Epoxy Seal
(6.35)
(4.8) .250
.189
(1.17)
.046
Thk = (0.8)
.031
(4.7) Typ
.185
1
(1.8) Dia Typ
.073
Single Pole
3
6
2
5
1
4
(4.7) Typ
.185
(1.8) Dia Typ
.073
Double Pole
3
6
9
2
5
8
1
4
(4.8) Typ
.189
(4.7) Typ
.185
7
3
6
9
12
2
5
8
11
1
4
7
10
(1.8) Dia Typ
.073
Three Pole
(4.8) Typ
.189
(4.7) Typ
.185
(1.8) Dia Typ
.073
Four Pole
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Series M
Flat Frame Mount Miniature Rockers
ROCKERS & PADDLES
For TN Frame
AT4148 .365” (9.27mm)
Wide Rocker
D
AT4149 .365” (9.27mm)
Wide Paddle
E
Material: Polyamide
Finish: Matte
Material: Polyamide
Finish: Matte
(2.13)
.084
(9.27)
.365
(9.27)
.365
(16.87)
.664
(13.49)
.531
(3.96)
.156
(18.8)
.740
(7.9) (6.15)
.311 .242
(3.5)
.138
AT4151 .450” (11.43mm)
Wide Paddle
G
Material: Polyamide
Finish: Matte
Material: Polyamide
Finish: Matte
(2.36)
.093
(11.43)
.450
(11.43)
.450
(3.5)
.138
(16.8)
.661
AT4150 .450” (11.43mm)
Wide Rocker
F
(8.43) R
.332
(8.8)
.346
(11.8)
.465
(9.19)
.362
(3.18)
.125
(16.36)
.644
(7.7)
.303
(8.1) (6.3)
.319 .248
(3.5)
.138
(5.84) R
.230
(3.5)
.138
(11.8)
.465
For TY Frame
J
AT4156 .595” (15.11mm)
Wide Rocker
H
Material: Polyamide
Finish: Matte
AT4157 .595” (15.11mm)
Wide Paddle
Material: Polyamide
Finish: Matte
(2.36)
.093
(14.33)
.564
(4.75)
.187
(15.11)
.595
(26.78)
1.054
(29.82)
1.174
(23.01)
.906
(11.0)
.433
(8.4) (6.5)
.331 .256
(7.3)
.287
(3.5)
.138
Cap Colors
Available:
A
(13.5) R
.531
Black
B
White
(26.8)
1.055
(15.11)
.595
C
Red
E
Yellow
F
Green
G
Blue
(3.5)
.138
H
Gray
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Flat Frame Mount Miniature Rockers
Series M
TYPICAL SWITCH DIMENSIONS
TN Frame • Solder Lug
Single Pole
(12.3)
.484
(2.4) Dia Typ
.094
(3.5)
.138
Circuit Mark
This Side
(1.1) x (2.0) Typ
.043 x. 079
3
(23.8)
.937
25°
(29.5)
1.161
(7.9)
.311
(9.65)
.380
TN Frame • Solder Lug
(0.6)
.024
(10.3)
.406
(13.0)
.512
2
(0.8) Typ
.031
(6.9)
.272
(9.27)
.365
M2012TNW01-DC
(4.7) Typ
.185
1
(0.5)
.020
(2.0)
.079
(7.9)
.311
(4.5)
.177
Double Pole
(2.4) Dia Typ
.094
(12.3)
.484
(2.0) Typ
.079
(1.1) x (2.0) Typ
.043 x. 079
(3.5)
.138
Circuit Mark
This Side
(29.5)
1.161
(23.8)
.937
(0.8) Typ
.031
(7.9)
.311
(9.65)
.380
(6.9)
.272
(9.27)
.365
M2022TNW01-DC
(4.7) Typ
.185
25°
TN Frame • Solder Lug
(0.6)
.024
(10.3)
.406
(4.5)
.177
6
3
5
2
4
1
(0.5)
.020
(13.0)
.512
(4.8)
.189
(12.7)
.500
Three Pole
(12.3)
.484
(2.4) Dia Typ
.094
(3.5)
.138
(1.1) x (2.0) Typ
.043 x .079
(2.0) Typ
.079
Circuit Mark
This Side
(23.8)
.937
(4.7) Typ
.185
25°
(29.5)
1.161
(0.8) Typ
.031
(6.9)
.272
(9.27)
.365
M2032TNW01-DC
TN Frame • Solder Lug
(7.9)
.311
(9.65)
.380
(0.6)
.024
(12.4)
.488
9
6
3
8
5
2
7
4
1
(13.0)
.512
(4.8) Typ
.189
(0.5)
.020
(4.5)
.177
(17.5)
.689
Four Pole
(12.3)
.484
(2.4) Dia Typ
.094
(2.0) Typ
.079
(1.1) x (2.0) Typ
.043 x .079
(3.5)
.138
Circuit Mark
This Side
(23.8)
.937
(29.5)
1.161
M2042TNW01-DC
(4.7) Typ
.185
25°
(0.8) Typ
.031
(6.9)
.272
(7.9)
.311
(9.27)
.365
(9.65)
.380
9
6
3
11
8
5
2
10
7
4
1
(0.5)
.020
(0.6)
.024
(12.4)
.488
12
(4.5)
.177
(13.0)
.512
(4.8) Typ
.189
(22.3)
.878
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Series M
Flat Frame Mount Miniature Rockers
TYPICAL SWITCH DIMENSIONS
TY Frame • Solder Lug
Single Pole
(14.5)
.571
(3.2) Dia Typ
.126
Double Pole
(1.1) x (2.0) Typ
.043 x .079
(3.5)
.138
Circuit Mark
This Side
(41.3)
1.626
(34.9)
1.374
3
(4.7) Typ
.185
25°
2
(0.8) Typ
.031
(12.8)
.504
(15.11)
.595
(8.4)
.331
(10.0)
.394
(0.6)
.024
(10.0)
.394
(4.5)
.177
(13.0)
.512
6
3
5
2
4
1
1
(0.5)
.020
(7.9)
.311
M2012TYW01-JC
(2.0)
.079
(4.8)
.189
(13.0)
.512
(2.0) Typ
.079
Double pole has barrier between terminals.
TY Frame • Solder Lugv
Three Pole
(3.2) Dia Typ
.126
(14.5)
.571
(2.0) Typ
.079
(1.1) x (2.0) Typ
.043 x .079
(3.5)
.138
Circuit Mark
This Side
(41.3)
1.626
(34.9)
1.374
(4.7) Typ
.185
25°
(0.8) Typ
.031
(8.4)
.331
(12.8)
.504
(15.11)
.595
(10.0)
.394
(0.6)
.024
(12.1)
.476
M2032TYW01-JC
TY Frame • Solder Lug
9
6
3
8
5
2
7
4
1
(13.0)
.512
(0.5)
.020
(4.8) Typ
.189
(4.5)
.177
(17.5)
.689
Four Pole
(3.2) Dia Typ
.126
(14.5)
.571
(2.0) Typ
.079
(3.5)
.138
(1.1) x (2.0) Typ
.043 x .079
Circuit Mark
This Side
12
(41.3)
1.626
(34.9)
1.374
(4.7) Typ
.185
25°
(0.8) Typ
.031
(12.8)
.504
(15.11)
.595
(8.4)
.331
(10.0)
.394
(0.6)
.024
(12.1)
.476
9
6
3
11
8
5
2
10
7
4
1
(0.5)
.020
(4.5)
.177
(22.3)
.878
(13.0)
.512
(4.8) Typ
.189
M2042TYW01-JC
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Flat Frame Mount Miniature Rockers
Series M
LEGENDS
General information and basic specifications are presented here for customers who want to do their own legends.
Suggested Printable Area for Cap
AT4150
AT4148
ON
F
(5.76) Typ
.227
(7.75)
.305
(9.27)
.365
F
OF
OF
F
OF
(0.76) Typ
.030
ON
ON
(0.38) Typ
.015
(6.9) Typ
.272
AT4156
(0.76) Typ
.030
(0.38) Typ
.015
(4.5) Typ
.177
(0.38) Typ
.015
(10.03) Typ
.395
(11.18) Typ
.440
(0.76) Typ
.030
(9.91)
.390
(11.43)
.450
(0.76) Typ
.030
(3.36) Typ
.132
(0.76) Typ
.030
(13.59)
.535
(15.11)
.595
(0.76) Typ
.030
Shaded areas are printable areas.
Recommended Print Method:
Screen Print or Pad Print
Epoxy based ink is recommended.
Additional Method
An additional method for legends is engraving the cap.
Maximum depth for engraving is .012” (0.3mm) on the cap.
Enamel paint is recommended to fill the engraved area.
LEGEND PACKET
1. To order caps with legends contact the factory and request the M Rocker Legend Packet.
2. Once you determine your desired legend, fill out the ordering work sheet included in the packet.
3. Return the completed work sheet to receive a quotation.
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
03-07
Similar pages