REJ10J0528-0120 M16C Flash Starter User's Manual M38507F8SP/FP, M38517F8SP/FP, M38507F8ASP/FP Example Circuit RENESAS SINGLE-CHIP MICROCOMPUTER 740 Family Rev.1.20 2006.12.01 Revision date: Dec 01, 2006 Renesas Solutions Corp. http://www.renesas.com/ 1. Using MF_Ten-Nine Cable Vcc CON 1 Vcc 10uF Vcc 0.1uF 2 Vss JUMPER Vcc CNVss Vcc IBM PC/AT 1 2 3 4 5 6 7 8 9 10 RxD P04(LED04) /RxD2 GND TxD Connector Type Straight(HIF3FC-10PA-2.54DSA) Angle(HIF3FC-10PA-2.54DS) P05(LED05) /TxD2 15pF XIN 8MHz Pin Assignment Pin No Port 1 XOUT Signal Vcc 15pF 2 3 4 5.1k AVss Vcc 5.1k P41/INT0 P26/SCLK Vcc p0_4 42P2R-A/E,42P4B 5.1k 10-9 Cable RxD 5 5.1k 6 7 GND 8 5.1k 9 10 p0_5 TxD Push SW RESET 4.7uF 3 P27/CNTR0/SRDY1 OPEN 2. Mode Setting Vcc Vss Vcc AVss 42 2 41 3 40 4 39 5 38 6 P41/INT0 P41 7 8 BUSY P27/CNTR0/SRDY1 9 SCLK P26/SCLK1 10 TxD P25/SCL2/TxD 11 RxD P24/SDA2/RxD 12 13 14 *2 CNVss Vpp RESET 42P2R-A/E,42P4B 1 37 36 35 34 33 32 31 30 29 15 28 16 27 17 26 RESET 18 25 XIN 19 24 XOUT 20 23 Vss 21 22 *1 Mode setup method Signal CNVss P41 RESET SCLK Value 4.5 to 5.5V Vss *3 Vss Vcc Vss * 1: Connect oscillator circuit. * 2: Connect to Vcc when Vcc = 4.5V to 5.5V. Connect to Vpp (= 4.5V to 5.5V) when Vcc = 2.7V to 4.5V. * 3: It is necessary to apply Vcc only when reset is released. 4 REVISION HISTORY Rev. Description Date Page 1.00 Jul 01, 2004 - 1.10 Feb.01.2006 P3 1.20 Dec.01.2006 - Summary First edition issued The circuit chart was corrected. (TxD pin: pull-up resistance addition.) Change to Note M16C Flash Starter User's Manual M38507F8SP/FP,M38517F8SP/FP,M38507F8ASP/FP Example Circuit Publication Rev.1.20 Dec 01, 2006 Date Published by: Renesas Solutions Corp. 4-1-6, Miyahara, Yodogawa-ku, Osaka City, 532-0003, Japan ©2004 Renesas Technology Corp. and Renesas Solutions Corp., All Rights Reserved. Printed in Japan. M16C Flash Starter User's Manual M38507F8SP/FP, M38517F8SP/FP, M38507F8ASP/FP Example Circuit Renesas Solutions Corp. 4-1-6, Miyahara, Yodogawa-ku, Osaka City, 532-0003, Japan