SDLS213B − DECEMBER 1983 − REVISED NOVEMBER 2004
D Dual Versions of Highly Stable SN54121
D
TYPE
MAXIMUM
OUTPUT
PULSE
LENGTH(S)
SN54221
21
SN74221
28
SN54LS221
49
SN74LS221
70
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
VCC
1Rext/Cext
1Cext
1Q
2Q
2CLR
2B
2A
SN54LS221 . . . FK PACKAGE
(TOP VIEW)
1B
1A
NC
VCC
1R ext /Cext
D
1A
1B
1CLR
1Q
2Q
2Cext
2Rext/Cext
GND
description/ordering information
1CLR
1Q
NC
2Q
2Cext
4
3 2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
2R ext/Cext
The ’221 and ’LS221 devices are dual
multivibrators with performance characteristics
virtually identical to those of the ’121 devices.
Each multivibrator features a negative-transitiontriggered input and a positive-transition-triggered
input, either of which can be used as an inhibit
input.
1Cext
1Q
NC
2Q
2CLR
GND
NC
2A
2B
D
SN54221, SN54LS221 . . . J PACKAGE
SN74221 . . . N PACKAGE
SN74LS221 . . . D, DB, N, OR NS PACKAGE
(TOP VIEW)
and SN74121 One Shots
SN54221 and SN74221 Demonstrate
Electrical and Switching Characteristics
That Are Virtually Identical to the SN54121
and SN74121 One Shots
Pinout Is Identical to the SN54123,
SN74123, SN54LS123, and SN74LS123
Overriding Clear Terminates Output Pulse
NC − No internal connection
ORDERING INFORMATION
PDIP − N
0°C to 70°C
−55°C
−55
C to 125
125°C
C
ORDERABLE
PART NUMBER
PACKAGE†
TA
Tube
TOP-SIDE
MARKING
SN74221N
SN74221N
SN74LS221N
SN74LS221N
Tube
SN74LS221D
Tape and reel
SN74LS221DR
SOP − NS
Tape and reel
SN74LS221NSR
74LS221
SSOP − DB
Tape and reel
SN74LS221DBR
LS221
SNJ54221J
SNJ54221J
SNJ54LS221J
SNJ54LS221J
SNJ54LS221FK
SNJ54LS221FK
SOIC − D
CDIP − J
Tube
LCCC − FK
Tube
LS221
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are
available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2004, Texas Instruments Incorporated
!"# $ %&'# "$ (&)*%"# +"#',
+&%#$ %! # $('%%"#$ (' #-' #'!$ '."$ $#&!'#$
$#"+"+ /""#0, +&%# (%'$$1 +'$ # '%'$$"*0 %*&+'
#'$#1 "** (""!'#'$,
(+&%#$ %!(*"# # 2343 "** (""!'#'$ "' #'$#'+
&*'$$ #-'/$' #'+, "** #-' (+&%#$ (+&%#
(%'$$1 +'$ # '%'$$"*0 %*&+' #'$#1 "** (""!'#'$,
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SDLS213B − DECEMBER 1983 − REVISED NOVEMBER 2004
description/ordering information (continued)
Pulse triggering occurs at a particular voltage level and is not directly related to the transition time of the input
pulse. Schmitt-trigger input circuitry (TTL hysteresis) for B input allows jitter-free triggering from inputs with
transition at rates as slow as 1 V/s, providing the circuit with excellent noise immunity, typically of 1.2 V. A high
immunity to VCC noise, typically of 1.5 V, also is provided by internal latching circuitry.
Once fired, the outputs are independent of further transitions of the A and B inputs and are a function of the timing
components, or the output pulses can be terminated by the overriding clear. Input pulses can be of any duration
relative to the output pulse. Output pulse length can be varied from 35 ns to the maximum by choosing
appropriate timing components. With Rext = 2 kΩ and Cext = 0, an output pulse typically of 30 ns is achieved
that can be used as a dc-triggered reset signal. Output rise and fall times are TTL compatible and independent
of pulse length. Typical triggering and clearing sequences are shown as a part of the switching characteristics
waveforms.
Pulse-width stability is achieved through internal compensation and is virtually independent of VCC and
temperature. In most applications, pulse stability is limited only by the accuracy of external timing components.
Jitter-free operation is maintained over the full temperature and VCC ranges for more than six decades of timing
capacitance (10 pF to 10 µF) and more than one decade of timing resistance (2 kΩ to 30 kΩ for the SN54221,
2 kΩ to 40 kΩ for the SN74221, 2 kΩ to 70 kΩ for the SN54LS221, and 2 kΩ to 100 kΩ for the SN74LS221).
Throughout these ranges, pulse width is defined by the relationship: tw(out) = CextRext In2 ≈ 0.7 CextRext. In
circuits where pulse cutoff is not critical, timing capacitance up to 1000 µF and timing resistance as low as 1.4 kΩ
can be used. Also, the range of jitter-free output pulse widths is extended if VCC is held to 5 V and free-air
temperature is 25°C. Duty cycles as high as 90% are achieved when using maximum recommended RT. Higher
duty cycles are available if a certain amount of pulse-width jitter is allowed.
The variance in output pulse width from device to device typically is less than ±0.5% for given external timing
components. An example of this distribution for the ’221 is shown in Figure 3. Variations in output pulse width
versus supply voltage and temperature for the ’221 are shown in Figures 4 and 5, respectively.
Pin assignments for these devices are identical to those of the SN54123/SN74123 or SN54LS123/SN74LS123
so that the ’221 or ’LS221 devices can be substituted for those products in systems not using the retrigger by
merely changing the value of Rext and/or Cext; however, the polarity of the capacitor must be changed.
FUNCTION TABLE
(each monostable multivibrator)
INPUTS
OUTPUTS
CLR
A
B
Q
Q
L
X
X
L
H
X
H
X
L
H
X
X
L
L
H
L
↑
†
†
H
†
†
H
†
†
H
↑‡
↓
L
H
† Pulsed-output patterns are tested during
AC switching at 25°C with Rext = 2 kΩ, and
Cext = 80 pF.
‡ This condition is true only if the output of
the latch formed by the two NAND gates
has been conditioned to the logic 1 state
prior to CLR going high. This latch is
conditioned by taking either A high or
B low while CLR is inactive (high).
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SDLS213B − DECEMBER 1983 − REVISED NOVEMBER 2004
timing component connections
VCC
Rext
To Cext
Terminal
To Rext/Cext
Terminal
NOTE: Due to the internal circuit, the Rext/Cext terminal never is more positive than the Cext terminal.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SDLS213B − DECEMBER 1983 − REVISED NOVEMBER 2004
schematics of inputs and outputs
SN54/74221
EQUIVALENT OF EACH INPUT
TYPICAL OF ALL OUTPUTS
VCC
VCC
100 Ω NOM
Req
Input
Output
A Input: Req = 4 kΩ NOM
B, CLR Input: Req = 2 kΩ NOM
SN54/74LS221
EQUIVALENT OF EACH INPUT
TYPICAL OF ALL OUTPUTS
VCC
VCC
120 Ω NOM
Req
Input
Output
A Input: Req = 25 kΩ NOM
B Input: Req = 15.4 kΩ NOM
CLR: Req = 12.5 kΩ NOM
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SDLS213B − DECEMBER 1983 − REVISED NOVEMBER 2004
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage range, VI (see Note 1): ’LS221 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
’221 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Package thermal impedance, θJA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73°C/W
DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82°C/W
N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67°C/W
NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
2. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions (see Note 3)
SN54221
VCC
IOH
Supply voltage
IOL
Low-level output current
∆v/∆t
MIN
NOM
4.5
5
High-level output current
Rise or fall of input pulse rate
SN74221
MAX
MIN
NOM
5.5
4.75
5
−800
16
MAX
UNIT
5.25
V
−800
µA
16
mA
B input
1*
1
V/s
A input
1*
1
V/µs
TA
Operating free-air temperature
−55
125
0
70
°C
∗ On products compliant to MIL-PRF-38535, this parameter is not production tested.
NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SDLS213B − DECEMBER 1983 − REVISED NOVEMBER 2004
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS†
VT+
Positive-going threshold voltage,
B input
VCC = MIN
VT−
Negative-going threshold voltage,
B input
VCC = MIN
MIN
SN54221
TYP‡
MAX
1.55
VIK
VOH
VCC = MIN,
VCC = MIN,
II = −12 mA
IOH = −800 µA
VOL
II
VCC = MIN,
VCC = MAX,
IOL = 16 mA
VI = 5.5 V
0.8*
1.35
2.4
3.4
CLR, B input
VCC = MAX,
VI = 2.4 V
0.2
VCC = MAX,
VI = 0.4 V
A input
IIL
CLR, B input
IOS§
ICC
VCC = MAX
Quiescent
Triggered
2*
SN74221
TYP‡
MAX
1.55
0.8
1.35
2.4
3.4
−1.5
A input
IIH
MIN
−20
VCC = MAX
2
0.2
1
1
40
80
80
−1.6
−1.6
−3.2
−3.2
−18
V
V
0.4
40
−55
V
V
−1.5
0.4
UNIT
−55
26
50*
26
50
46
80*
46
80
V
mA
µA
A
mA
mA
mA
∗ On products compliant to MIL-PRF-38535, this parameter is not production tested.
† For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
‡ All typical values are at VCC = 5 V, TA = 25°C.
§ Not more than one output should be shorted at a time, and the duration of the short circuit should not exceed one second.
timing requirements over recommended ranges of supply voltage and operating free-air
temperature
tw
Pulse duration
tsu
Setup time, inactive-state¶
Rext
External timing resistance
Cext
External timing capacitance
Output duty cycle
POST OFFICE BOX 655303
SN74221
MIN
MAX
A or B input
50
50
CLR
20
20
CLR
15
15
MAX
ns
1.4*
30*
1.4
40
kΩ
0*
1000*
0
1000
µF
67%
67%
Rext = MAX Rext
90%
90%
• DALLAS, TEXAS 75265
UNIT
ns
Rext = 2 kΩ
∗ On products compliant to MIL-PRF-38535, this parameter is not production tested.
¶ Inactive-state setup time also is referred to as recovery time.
6
SN54221
MIN
SDLS213B − DECEMBER 1983 − REVISED NOVEMBER 2004
switching characteristics VCC = 5 V, RL = 400 Ω, TA = 25_C (see Figures 1 and 2)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
SN54221
TEST CONDITIONS
MIN
A
tPLH
B
Q
Cext = 80 pF,
A
tPHL
tPHL
tPLH
tw
B
Rext = 2 kΩ
Q
TYP
MAX
TYP
MAX
45
70
45
70
35
55
35
55
50
80
50
80
40
65
40
65
Q
CLR
A or B
Q
Q or Q
SN74221
MIN
27
27
40
40
Cext = 80 pF,
Rext = 2 kΩ
Cext = 80 pF,
Rext = 2 kΩ
70
110
150
70
110
150
Cext = 0,
Rext = 2 kΩ
17
30
50
17
30
50
Cext = 100 pF,
Rext = 10 kΩ
650
700
750
650
700
750
Cext = 1 µF,
Rext = 10 kΩ
6.5*
7
7.5*
6.5
7
7.5
MAX
MIN
NOM
5.5
4.75
5
UNIT
ns
ns
ns
ms
∗ On products compliant to MIL-PRF-38535, this parameter is not production tested.
recommended operating conditions (see Note 4)
SN54LS221
VCC
IOH
Supply voltage
IOL
Low-level output current
∆v/∆t
MIN
NOM
4.5
5
High-level output current
−400
4
B input
Rise or fall of input pulse rate
SN74LS221
A input
1*
1*
MAX
UNIT
5.25
V
−400
µA
8
mA
1
V/s
1
V/µs
TA
Operating free-air temperature
−55
125
0
70
°C
∗ On products compliant to MIL-PRF-38535, this parameter is not production tested.
NOTE 4: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SDLS213B − DECEMBER 1983 − REVISED NOVEMBER 2004
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
VT+
Positive-going threshold voltage,
B input
VCC = MIN
VT−
Negative-going threshold voltage,
B input
VCC = MIN
VIK
VOH
MIN
1
VCC = MIN,
VCC = MIN,
II = −18 mA
IOH = −400 µA
VOL
VCC = MIN
IOL = 4 mA
IOL = 8 mA
II
VCC = MAX,
VI = 7 V
VCC = MAX,
VI = 2.7 V
IIH
SN54LS221
TYP‡
MAX
TEST CONDITIONS†
0.7*
0.9
2.5
3.4
CLR, B input
IOS§
ICC
VCC = MAX,
0.25
Triggered
1
V
2*
0.8
0.9
2.7
3.4
VI = 0.4 V
−20
VCC = MAX
2
V
−1.5
0.4
0.4
0.35
0.5
mA
µA
20
20
−0.4
−0.8
−0.8
−20
V
0.1
−0.4
−100
V
V
0.25
0.1
VCC = MAX
Quiescent
UNIT
−1.5
A input
IIL
SN74LS221
TYP‡
MAX
MIN
−100
4.7
11
4.7
11
19
27*
19
27
mA
mA
mA
∗ On products compliant to MIL-PRF-38535, this parameter is not production tested.
† For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
‡ All typical values are at VCC = 5 V, TA = 25°C.
§ Not more than one output should be shorted at a time, and the duration of the short circuit should not exceed one second.
timing requirements over recommended ranges of supply voltage and operating free-air
temperature
SN54LS221
MIN
tw
Pulse duration
tsu
Setup time, inactive state¶
Rext
External timing resistance
Cext
External timing capacitance
50
50
40
40
RT = 2 kΩ
RT = MAX Rext
POST OFFICE BOX 655303
MIN
CLR
∗ On products compliant to MIL-PRF-38535, this parameter is not production tested.
¶ Inactive-state setup time also is referred to as recovery time.
8
SN74LS221
A or B
CLR
Output duty cycle
MAX
• DALLAS, TEXAS 75265
15
MAX
UNIT
ns
15
ns
1.4*
70*
1.4
100
kΩ
0*
1000*
0
1000
µF
50%
50%
90%
90%
SDLS213B − DECEMBER 1983 − REVISED NOVEMBER 2004
switching characteristics VCC = 5 V, RL = 2 kΩ, TA = 25_C (see Figures 1 and 2)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
SN54LS221
TEST CONDITIONS
MIN
A
tPLH
B
Q
Cext = 80 pF,
A
tPHL
tPHL
tPLH
tw
B
Rext = 2 kΩ
Q
Q
CLR
A or B
Q
Q or Q
SN74LS221
TYP
MAX
45
MIN
TYP
MAX
70
45
70
35
55
35
55
50
80
50
80
40
65
40
65
35
55
35
55
44
65
44
65
Cext = 80 pF,
Rext = 2 kΩ
Cext = 80 pF,
Rext = 2 kΩ
70
120
150
70
120
150
Cext = 0,
Rext = 2 kΩ
20
47
70
20
47
70
Cext = 100 pF,
Rext = 10 kΩ
670
740
810
670
740
810
Cext = 1 µF,
Rext = 10 kΩ
6*
6.9
7.5*
6
6.9
7.5
UNIT
ns
ns
ns
ms
∗ On products compliant to MIL-PRF-38535, this parameter is not production tested.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SDLS213B − DECEMBER 1983 − REVISED NOVEMBER 2004
PARAMETER MEASUREMENT INFORMATION
tw
3V
B†
0V
≥ 60 ns
3V
CLR
0V
tPLH
tPHL
VOH
Q
VOL
tPHL
tPLH
VOH
Q
VOL
CONDITION 1: TRIGGER FROM B, THEN CLR
3V
B†
0V
≥ 60 ns
3V
CLR
0V
VOH
Q
VOL
CONDITION 2: TRIGGER FROM B, THEN CLR
3V
B†
0V
≥ 50 ns
≥0
tsu
3V
CLR
0V
tw
Triggered
VOH
Q
VOL
Not Triggered
CONDITION 3: CLR OVERRIDING B, THEN TRIGGER FROM B
† A is low.
Figure 1. Switching Characteristics
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SDLS213B − DECEMBER 1983 − REVISED NOVEMBER 2004
PARAMETER MEASUREMENT INFORMATION
3V
B†
0V
≥ 50 ns
≥ 50 ns
3V
CLR
0V
VOH
Q
VOL
CONDITION 4: TRIGGERING FROM POSITIVE TRANSITION OF CLR
tw
3V
A‡
0V
≥ 60 ns
3V
CLR
0V
tPLH
tPHL
VOH
Q
VOL
tPHL
tPLH
VOH
Q
VOL
CONDITION 5: TRIGGER FROM A, THEN CLR
3V
A‡
0V
tw
VOH
Q
VOL
tw
VOH
Q
VOL
CONDITION 6: TRIGGER FROM A
† A is low.
‡ B and CLR are high.
NOTES: A. Input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO ≈ 50Ω; for SN54/74221, tr ≤ 7 ns,
tf ≤ 7 ns, for SN54/74LS221, tr ≤ 15 ns, tf ≤ 6 ns.
B. All measurements are made between the 1.5-V points of the indicated transitions for the SN54/74221 or between the 1.3-V points
for the SN54/74LS221.
Figure 1. Switching Characteristics (Continued)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
SDLS213B − DECEMBER 1983 − REVISED NOVEMBER 2004
PARAMETER MEASUREMENT INFORMATION
VCC
Test
Point
RL
From Output
Under Test
(see Note B)
CL = 15 pF
(see Note A)
High-Level
Pulse
tw
Low-Level
Pulse
LOAD CIRCUIT FOR
BI-STATE
TOTEM-POLE OUTPUTS
VOLTAGE WAVEFORMS
PULSE DURATIONS
3V
Input
tPLH
3V
Timing
Input
VOH
In-Phase
Output
0V
tsu
th
tPHL
3V
Data
Input
0V
0V
tPHL
VOL
tPLH
VOH
Out-of-Phase
Output
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
NOTES: A.
B.
C.
D.
CL includes probe and jig capacitance.
All diodes are 1N3064 or equivalent.
In the examples above, the phase relationships between inputs and outputs have been chosen arbitrarily.
All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO ≈ 50 Ω and, for SN54/74221,
tr ≤ 7 ns, tf ≤ 7 ns, for SN54/74LS221, tr ≤ 15 ns, tf ≤ 6 ns.
E. All measurements are made between the 1.5-V points of the indicated transitions for the SN54/74221 or between the 1.3-V points
for the SN54/74LS221.
Figure 2. Load Circuits and Voltage Waveforms
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SDLS213B − DECEMBER 1983 − REVISED NOVEMBER 2004
TYPICAL CHARACTERISTICS (SN54/74221 ONLY)†
VARIATION IN OUTPUT PULSE
vs
SUPPLY VOLTAGE
DISTRIBUTION OF UNITS
FOR
OUTPUT PULSE
1
Relative Frequency of Occurrence
∆ t w − Variation in Output Pulse − %
VCC = 5 V
TA = 25°C
Median
+0.5%
Cext = 60 pF
Rext = 10 kΩ
TA = 25°C
0.5
tw ≈ 420 ns
at VCC = 5 V
0
− 0.5
Median
+0.5%
−1
4.5
Median
4.75
5.5
VCC − Supply Voltage − V
tw − Output Pulse
Figure 3
Figure 4
VARIATION IN OUTPUT PULSE
vs
FREE-AIR TEMPERATURE
OUTPUT PULSE
vs
TIMING RESISTOR VALUE
1
10 ms
Cext = 1 µ F
VCC = 5 V
Cext = 60 pF
Rext = 10 kΩ
1 ms
Cext = 0.1 µ F
0.5
t w − Output Pulse
∆ t w − Variation in Output Pulse − %
5.25
5
tw ≈ 420 ns
at TA = 25°C
0
100 µs
Cext = 0.01 µ F
10 µs
Cext = 1000 pF
1 µs
Cext = 100 pF
− 0.5
Cext = 10 pF
100 ns
−1
−75 −50
VCC = 5 V
TA = 25°C
10 ns
−25
0
25
50
75
100
125
1
2
TA − Free-Air Temperature − °C
See Note A
4
7 10
20
40
70 100
Rext − Timing Resistor Value − kΩ
Figure 5
Figure 6
† Data for temperatures below 0°C and above 70°C, and for supply voltages below 4.75 V and above 5.25 V are applicable for the SN54221 only.
NOTE A: These values of resistance exceed the maximum recommended for use over the full military temperature range of the SN54221.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
5962-8771101EA
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
5962-8771101EA
SNJ54221J
76042012A
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
76042012A
SNJ54LS
221FK
7604201EA
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
7604201EA
SNJ54LS221J
7604201FA
ACTIVE
CFP
W
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
7604201FA
SNJ54LS221W
JM38510/31402B2A
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
JM38510/
31402B2A
JM38510/31402BEA
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
JM38510/
31402BEA
JM38510/31402BFA
ACTIVE
CFP
W
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
JM38510/
31402BFA
M38510/31402B2A
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
JM38510/
31402B2A
M38510/31402BEA
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
JM38510/
31402BEA
M38510/31402BFA
ACTIVE
CFP
W
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
JM38510/
31402BFA
SN54221J
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
SN54221J
SN54LS221J
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
SN54LS221J
SN74221N
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
0 to 70
SN74221N
SN74221NE4
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
0 to 70
SN74221N
SN74LS221D
ACTIVE
SOIC
D
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
LS221
SN74LS221DBR
ACTIVE
SSOP
DB
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
LS221
SN74LS221DBRE4
ACTIVE
SSOP
DB
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
LS221
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2013
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
SN74LS221DBRG4
ACTIVE
SSOP
DB
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
LS221
SN74LS221DE4
ACTIVE
SOIC
D
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
LS221
SN74LS221DG4
ACTIVE
SOIC
D
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
LS221
SN74LS221DR
ACTIVE
SOIC
D
16
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
LS221
SN74LS221DRE4
ACTIVE
SOIC
D
16
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
LS221
SN74LS221DRG4
ACTIVE
SOIC
D
16
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
LS221
SN74LS221N
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
0 to 70
SN74LS221N
SN74LS221N3
OBSOLETE
PDIP
N
16
TBD
Call TI
Call TI
0 to 70
SN74LS221NE4
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
0 to 70
SN74LS221N
SN74LS221NSR
ACTIVE
SO
NS
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
74LS221
SN74LS221NSRE4
ACTIVE
SO
NS
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
74LS221
SN74LS221NSRG4
ACTIVE
SO
NS
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
74LS221
SNJ54221J
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
5962-8771101EA
SNJ54221J
SNJ54LS221FK
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
76042012A
SNJ54LS
221FK
SNJ54LS221J
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
7604201EA
SNJ54LS221J
SNJ54LS221W
ACTIVE
CFP
W
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
7604201FA
SNJ54LS221W
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2013
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF SN54221, SN54LS221, SN74221, SN74LS221 :
• Catalog: SN74221, SN74LS221
• Military: SN54221, SN54LS221
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
• Military - QML certified for Military and Defense Applications
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SN74LS221DBR
SSOP
SN74LS221DR
SN74LS221NSR
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
12.0
16.0
Q1
DB
16
2000
330.0
16.4
8.2
6.6
2.5
SOIC
D
16
2500
330.0
16.4
6.5
10.3
2.1
8.0
16.0
Q1
SO
NS
16
2000
330.0
16.4
8.2
10.5
2.5
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
SN74LS221DBR
SSOP
DB
16
2000
367.0
367.0
38.0
SN74LS221DR
SOIC
D
16
2500
333.2
345.9
28.6
SN74LS221NSR
SO
NS
16
2000
367.0
367.0
38.0
Pack Materials-Page 2
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
0,15 M
15
0,25
0,09
8,20
7,40
5,60
5,00
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
2,00 MAX
0,10
0,05 MIN
PINS **
14
16
20
24
28
30
38
A MAX
6,50
6,50
7,50
8,50
10,50
10,50
12,90
A MIN
5,90
5,90
6,90
7,90
9,90
9,90
12,30
DIM
4040065 /E 12/01
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-150
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated