STMICROELECTRONICS M41T315V

M41T315Y
M41T315V, M41T315W
Serial access phantom RTC supervisor
Not For New Design
Features
■
3.0V, 3.3V, or 5V operating voltage
■
Real-time clock keeps track of
tenths/hundredths of seconds, seconds,
minutes, hours, days, date of the month,
months, and years
■
Automatic leap year correction valid up to 2100
■
Automatic switch-over and deselect circuitry
■
Choice of power-fail deselect voltages:
(VPFD = power-fail deselect voltage)
– M41T315Y(a): VCC = 4.5 to 5.5V
4.25V ≤ VPFD ≤ 4.50V
– M41T315V: VCC = 3.0 to 3.6V
2.80V ≤ VPFD ≤ 2.97V
– M41T315W: VCC = 2.7 to 3.3V
2.60V ≤ VPFD ≤ 2.70V
■
No address space required to communicate
with RTC
■
Provides nonvolatile supervisor functions for
battery backup of SRAM
■
Full ±10% VCC operating range
■
Industrial operating temperature range (–40 to
+85°C)
■
Ultra-low battery supply current of 500nA (max)
■
Optional packaging includes A 28-lead SOIC
and SNAPHAT® top (to be ordered separately)
■
SNAPHAT package provides direct connection
for a snaphat top, which contains the battery
and crystal
■
RoHS compliant
– Lead-free second level interconnect
16
1
SO16 (MQ)
SNAPHAT (SH)
battery & crystal
28
1
SOH28 (MH)
a. Contact local ST sales office for availability.
November 2007
Rev 3
This is information on a product still in production but not recommended for new designs.
1/30
www.st.com
1
Contents
M41T315Y, M41T315V, M41T315W
Contents
1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3
2.1
Non-volatile supervisor operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2
Data retention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Clock operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.1
Clock register information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2
AM-PM/12/24 mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.3
Oscillator and reset bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.4
Zero bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4
Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
8
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2/30
M41T315Y, M41T315V, M41T315W
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
AC electrical characteristics (M41T315Y). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
AC electrical characteristics (M41T315V/W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
RTC register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Ablolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
DC and AC measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DC characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Crystal electrical characteristics (externally supplied) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Power down/up trip points DC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SO16 - 16-lead plastic small outline (150 mils body width), package mechanical data . . . 23
SOH28 - 28-lead plastic small outline, package mechanical data . . . . . . . . . . . . . . . . . . . 24
SH - 4-pin SNAPHAT housing for 48mAh battery and crystal, package mechanical data . 25
SH - 4-pin SNAPHAT housing for 120mAh battery and crystal, package mechanical data 26
Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SNAPHAT battery table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3/30
List of figures
M41T315Y, M41T315V, M41T315W
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
4/30
Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
16-pin SOIC connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
28-pin SOIC connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
M41T315Y/V/W to RAM/clock interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Read mode waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Write mode waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Comparison register definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Reset pulse waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
AC testing load circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Power down/up mode AC waveforms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SO16 - 16-lead plastic small outline, package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
SOH28 - 28-lead plastic small outline, package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
SH - 4-pin SNAPHAT housing for 48mAh battery and crystal, package mechanical data . 25
SH - 4-pin SNAPHAT housing for 120mAh battery and crystal, package outline . . . . . . . . 26
M41T315Y, M41T315V, M41T315W
1
Description
Description
The M41T315Y/V/W RTC Supervisor is a combination of a CMOS TIMEKEEPER® and a
nonvolatile memory supervisor. Power is constantly monitored by the memory supervisor. In
the event of power instability or absence, an external battery maintains the timekeeping
operation and provides power for a CMOS static RAM by switching on and invoking write
protection to prevent data corruption in the memory and RTC.
The clock keeps track of tenths/hundredths of seconds, seconds, minutes, hours, day, date,
month, and year information. The last day of the month is automatically adjusted for months
with less than 31 days, including leap year correction.
The clock operates in one of two formats:
●
a 12-hour mode with an AM/PM indicator;
or
●
a 24-hour mode
The nonvolatile supervisor supplies all the necessary support circuitry to convert a CMOS
RAM to a nonvolatile memory. The M41T315Y/V/W can be interfaced with RAM without
leaving gaps in memory.
The M41T315Y/V/W is supplied in a 28-lead SOIC SNAPHAT® package (which integrates
both crystal and battery in a single SNAPHAT top) or a-16 pin SOIC. The 28-pin, 330mil
SOIC provides sockets with gold plated contacts at both ends for direct connection to a
separate SNAPHAT housing containing the battery and crystal. The unique design allows
the SNAPHAT battery/crystal package to be mounted on top of the SOIC package after the
completion of the surface mount process.
Insertion of the SNAPHAT housing after reflow prevents potential battery and crystal
damage due to the high temperatures required for device surface-mounting. The SNAPHAT
housing is also keyed to prevent reverse insertion.
The 28-pin SOIC and battery/crystal packages are shipped separately in plastic anti-static
tubes or in Tape & Reel form. For the 28-lead SOIC, the battery/crystal package (e.g.,
SNAPHAT) part number is “M4TXX-BR12SH” (see Table 17 on page 28).
Caution:
Do not place the SNAPHAT battery/crystal top in conductive foam, as this will drain the
lithium button-cell battery.
5/30
Description
M41T315Y, M41T315V, M41T315W
Figure 1.
Logic diagram
VCCI VCCO
D
XI
Q
(1)
(1)
CEO
XO
M41T315Y
M41T315V
M41T315W
WE
CEI
OE
RST
(1)
VBAT
VSS
AI03902
1. For 16-pin SOIC only
Table 1.
Signal names
XI-XO
6/30
32.768 KHz crystal connection
D
Data input
Q
Data output
RST
Reset input
CEO
Chip enable output
CEI
Chip enable input
VBAT
Battery input
OE
Output enable input
WE
WRITE enable input
VCCO
Switched supply voltage output
VCCI
Supply voltage input
VSS
Ground
NC
Not connected internally
DU
Don’t Use
M41T315Y, M41T315V, M41T315W
Figure 2.
Description
16-pin SOIC connections
XI
XO
WE
VBAT(1)
VSS
D
Q
VSS
16
1
2
15
3
14
4 M41T315Y 13
M41T315V
5 M41T315W 12
6
11
7
10
8
9
VCCI
VCCO
DU
RST
OE
CEI
CEO
NC
AI03909
Figure 3.
28-pin SOIC connections
WE
NC
NC
NC
NC
NC
NC
VSS
NC
NC
D
Q
NC
VSS
1
2
3
4
5
6
M41T315Y
7 M41T315V
8 M41T315W
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
VCCI
NC
NC
VCCO
DU
NC
RST
NC
OE
NC
NC
CEI
CEO
NC
AI03910
7/30
Description
Figure 4.
M41T315Y, M41T315V, M41T315W
Block diagram
XO
32,768 Hz
CRYSTAL
CLOCK/CALENDAR LOGIC
XI
CEO
UPDATE
READ
CEI
OE
WE
CONTROL
LOGIC
TIMEKEEPER REGISTER
WRITE
POWER-FAIL
RST
ACCESS
ENABLE
SEQUENCE
DETECTOR
D
Q
I/O
BUFFERS
VCCI
COMPARISON REGISTER
DATA
INTERNAL VCC
POWER-FAIL
DETECT
LOGIC
VBAT
8/30
VCCO
AI03636B
M41T315Y, M41T315V, M41T315W
Figure 5.
Description
M41T315Y/V/W to RAM/clock interface
A0-An
A0-An
WE
WE
OE
OE
DATA I/O
D0-D7
CMOS
SRAM
CE
VCC
CEO
VCCO
OE
WE
CE
CEI
RST
D
M41T315Y/V/W
RST
VCC
Q
VCCI
VBAT
X0
BAT
X1
+
VSS
VSS
32.768 Hz
CRYSTAL
AI04258
9/30
Operation
2
M41T315Y, M41T315V, M41T315W
Operation
Figure 6 on page 11 illustrates the main elements of the device. The following paragraphs
describe the signals and functions.
Communication with the clock is established by pattern recognition of a serial bit stream of
64 bits which must be matched by executing 64 consecutive WRITE cycles containing the
proper data on data in (D). All accesses which occur prior to recognition of the 64-bit pattern
are directed to memory via the chip enable output pin (CEO).
After recognition is established, the next 64 READ or WRITE Cycles either extract or update
data in the clock and CEO remains high during this time, disabling the connected memory
(see Table 2 on page 11).
Data transfer to and from the timekeeping function is accomplished with a serial bit stream
under control of chip enable input (CEI), output enable (OE), and WRITE enable (WE).
Initially, a READ cycle using the CEI and OE control of the clock starts the pattern
recognition sequence by moving the pointer to the first bit of the 64-bit comparison register.
Next, 64 consecutive WRITE cycles are executed using the CEI and WE control of the clock.
These 64 WRITE cycles are used only to gain access to the clock.
When the first WRITE cycle is executed, it is compared to the first bit of the 64-bit
comparison register. If a match is found, the pointer increments to the next location of the
comparison register and awaits the next WRITE cycle.
If a match is not found, the pointer does not advance and all subsequent WRITE cycles are
ignored. If a READ cycle occurs at any time during pattern recognition, the present
sequence is aborted and the comparison register pointer is reset. Pattern recognition
continues for a total of 64 WRITE cycles as described above until all the bits in the
comparison register have been matched (see Figure 8 on page 14).
With a correct match for 64 bits, access to the registers is enabled and data transfer to or
from the timekeeping registers may proceed. The next 64 cycles will cause the device to
either receive data on D, or transmit data on Q, depending on the level of OE pin or the WE
pin. Cycles to other locations outside the memory block can be interleaved with CEI cycles
without interrupting the pattern recognition sequence or data transfer sequence to the
device.
For a SO16 pin package, a standard 32.768 kHz quartz crystal can be directly connected to
the M41T315Y/V/W via pins 1 and 2 (XI, XO). The crystal selected for use should have a
specified load capacitance (CL) of 12.5 pF (see Table 10 on page 21).
10/30
M41T315Y, M41T315V, M41T315W
Table 2.
Operation
Operating modes
Mode
Deselect
WRITE
READ
READ
VCC
CEI
OE
WE
D
Q
Power
4.5 to 5.5V
or
3.0 to 3.6V
or
2.7 to 3.3V
VIH
X
X
Hi-Z
Hi-Z
Standby
VIL
X
VIL
DIN
Hi-Z
Active
VIL
VIL
VIH
Hi-Z
DOUT
Active
VIL
VIH
VIH
Hi-Z
Hi-Z
Active
X
X
X
Hi-Z
Hi-Z
CMOS standby
X
X
X
Hi-Z
Hi-Z
Battery back-up mode
VSO to VPFD
Deselect
≤
Deselect
(min)(1)
VSO(1)
1. See Table 11 on page 21 for details.
2.1
Non-volatile supervisor operation
A switch is provided to direct power from the battery input or VCCI to VCCO with a maximum
voltage drop of 0.3 Volts. The VCCO output pin is used to supply uninterrupted power to
CMOS SRAM. The M41T315Y/V/W safeguards the clock and RAM data by power-fail
detection and write protection.
Power-fail detection occurs when VCCI falls below VPFD which is set by an internal bandgap
reference. The M41T315Y/V/W constantly monitors the VCCI supply pin. When VCCI is less
than VPFD, power-fail circuitry forces the chip enable output (CEO) to VCCI or VBAT-0.2 volts
for external RAM write protection. During nominal supply conditions, CEO will track CEI with
a propagation delay. Internally, the M41T315Y/V/W aborts any data transfer in progress
without changing any of the device registers and prevents future access until VCCI exceeds
VPFD. Figure 5 on page 9 illustrates a typical RAM/clock interface.
Figure 6.
Read mode waveforms
WE
tRC
tCW
tRR
tCO
CEI
tOW
tOD
OE
tOE
tODO
tOEE
tCOE
Q
DATA OUTPUT VALID
AI04259
11/30
Operation
M41T315Y, M41T315V, M41T315W
Figure 7.
Write mode waveforms
OE
tWC
tWP
tWR
WE
tWR
tCW
CEI
t DH
tDH
tDS
D
DATA INPUT STABLE
AI04261
Table 3.
AC electrical characteristics (M41T315Y)
Symbol
Parameter(1)
Min
Typ
Max
Units
tAVAV
tRC
READ cycle time
tELQV
tCO
CEI access time
55
ns
tGLQV
tOE
OE access time
55
ns
tELQX
tCOE
CEI to output low Z
5
ns
tGLQX
tOEE
OE to output low Z
5
ns
tEHQZ
tOD
CEI to output high Z
25
ns
tGHQZ
tODO
OE to output high Z
25
ns
65
ns
tRR
READ recovery
10
ns
tELEH
tCW
CEI pulse width
55
ns
tGLGH
tOW
OE pulse width
55
ns
tAVAV
tWC
WRITE cycle
65
ns
tWLWH
tWP
WRITE pulse width
55
ns
tEHAX
tWHAX
tWR(2)
WRITE recovery
10
ns
tDVEH
tDVWH
tDS(3)
Data setup
30
ns
tEHDX
tWHDX
tDH(3)
Data hold time
0
ns
tRST
RST pulse width
65
ns
1. Valid for ambient operating temperature: TA = –40 to 85°C; VCC = 4.5 to 5.5V (except where noted).
2. tWR is a function of the latter occurring edge of WE or CEI.
3. tDH and tDS are functions of the first occurring edge of WE or CEI in RAM mode.
12/30
M41T315Y, M41T315V, M41T315W
Table 4.
Operation
AC electrical characteristics (M41T315V/W)
Symbol
Parameter(1)
Min
Typ
Max
Units
tAVAV
tRC
READ cycle time
tELQV
tCO
CEI access time
85
ns
tGLQV
tOE
OE access time
85
ns
tELQX
tCOE
CEI to output low Z
5
ns
tGLQX
tOEE
OE to output low Z
5
ns
tEHQZ
tOD
CEI to output high Z
30
ns
tGHQZ
tODO
OE to output high Z
30
ns
85
ns
tRR
READ recovery
20
ns
tELEH
tCW
CEI pulse width
65
ns
tGLGH
tOW
OE pulse width
60
ns
tAVAV
tWC
WRITE cycle
85
ns
tWLWH
tWP
WRITE pulse width
60
ns
tEHAX
tWHAX
tWR(2)
WRITE recovery
25
ns
tDVEH
tDVWH
tDS(3)
Data setup
35
ns
tEHDX
tWHDX
tDH(3)
Data hold time
5
ns
tRST
RST pulse width
85
ns
1. Valid for ambient operating temperature: TA = –40 to 85°C; VCC = 4.5 to 5.5V (except where noted).
2. tWR is a function of the latter occurring edge of WE or CEI.
3. tDH and tDS are functions of the first occurring edge of WE or CEI in RAM mode.
13/30
Operation
Figure 8.
M41T315Y, M41T315V, M41T315W
Comparison register definition
Hex
Value
7
6
5
4
3
2
1
0
BYTE 0
1
1
0
0
0
1
0
1
C5
BYTE 1
0
0
1
1
1
0
1
0
3A
BYTE 2
1
0
1
0
0
0
1
1
A3
BYTE 3
0
1
0
1
1
1
0
0
5C
BYTE 4
1
1
0
0
0
1
0
1
C5
BYTE 5
0
0
1
1
1
0
1
0
3A
BYTE 6
1
0
1
0
0
0
1
1
A3
BYTE 7
0
1
0
1
1
1
0
0
5C
AI04262
Note:
Pattern recognition in “hex” is C5, 3A, A3, 5C, C5, 3A, A3, and 5C. The odds of this pattern
being accidentally duplicated and sending aberrant entries to the RTC is less than 1 in 1019.
This pattern is sent to the clock LSB to MSB.
2.2
Data retention
Most low power SRAMs on the market today can be used with the M41T315Y/V/W. There
are, however some criteria which should be used in making the final choice of an SRAM to
use. The SRAM must be designed in a way where the chip enable input disables all other
inputs to the SRAM. This allows inputs to the M41T315Y/V/W and SRAMs to be Don’t Care
once VCCI falls below VPFD(min). The SRAM should also guarantee data retention down to
VCC = 2.0 volts. The chip enable access time must be sufficient to meet the system needs
with the chip enable output propagation delays included. If the SRAM includes a second
chip enable pin (E2), this pin should be tied to VOUT.
If data retention lifetime is a critical parameter for the system, it is important to review the
data retention current specifications for the particular SRAMs being evaluated. Most SRAMs
specify a data retention current at 3.0 volts. Manufacturers generally specify a typical
condition for room temperature along with a worst case condition (generally at elevated
temperatures). The system level requirements will determine the choice of which value to
14/30
M41T315Y, M41T315V, M41T315W
Operation
use. The data retention current value of the SRAMs can then be added to the IBAT value of
the M41T315Y/V/W to determine the total current requirements for data retention. The
available battery capacity for the SNAPHAT® of your choice can then be divided by this
current to determine the amount of data retention available (see Table 17 on page 28).
For a further more detailed review of lifetime calculations, please see Application Note
AN1012.
15/30
Clock operation
3
Clock operation
3.1
Clock register information
M41T315Y, M41T315V, M41T315W
Clock information is contained in eight registers of 8 bits, each of which is sequentially
accessed 1 bit at a time after the 64-bit pattern recognition sequence has been completed.
When updating the clock registers, each must be handled in groups of 8 bits. Writing and
reading individual bits within a register could produce erroneous results. These
READ/WRITE registers are defined in Table 5 on page 17.
Data contained in the clock registers is in binary coded decimal format (BCD). Reading and
writing the registers is always accomplished by stepping though all eight registers, starting
with Bit 0 of Register 0 and ending with Bit 7 of Register 7.
3.2
AM-PM/12/24 mode
Bit 7 of the hours register is defined as the 12-hour or 24-hour mode select bit. When high,
the 12-hour mode is selected. In the 12-hour mode, Bit 5 is the AM/PM bit with logic high
being PM. In the 24-hour mode, Bit 5 is the second 10-hour bit (20-23 hours).
3.3
Oscillator and reset bits
Bits 4 and 5 of the day register are used to control the reset and oscillator functions. Bit 4
controls the reset pin input. When the Reset Bit is set to logic '1,' the reset input pin is
ignored. When the Reset Bit is set to logic '0,' a low input on the reset pin will cause the
device to abort data transfer without changing data in the timekeeping registers. Reset
operates independently of all other inputs. Bit 5 controls the oscillator. When set to logic '0,'
the oscillator turns on and the real-time clock/calendar begins to increment.
3.4
Zero bits
Registers 1, 2, 3, 4, 5, and 6 contain one (1) or more bits that will always read logic '0.' When
writing to these locations, either a logic '1' or '0' is acceptable.
16/30
M41T315Y, M41T315V, M41T315W
Table 5.
Clock operation
RTC register map
Function/range
Register
D7
D6
0
D5
D4
D3
0.1 seconds
D2
D1
D0
BCD format
0.01 seconds
seconds
00-99
1
0
10 seconds
seconds
seconds
00-59
2
0
10 minutes
minutes
minutes
00-59
3
12/24
0
10/
A/P
hrs
hours (24 hour format)
hours
01-12/
00-23
4
0
0
OSC
RST
day
01-07
5
0
0
date: day of the month
date
01-31
6
0
0
month
month
01-12
year
year
00-99
7
10 date
0
0
day of the week
10M
10 years
Keys:
A/P = AM/PM bit
12/24 = 12 or 24-hour mode bit
OSC = Oscillator bit
RST = Reset bit
0 = Must be set to ‘0’
Figure 9.
Reset pulse waveform
RST
tRST
AI04260
17/30
Maximum rating
4
M41T315Y, M41T315V, M41T315W
Maximum rating
Stressing the device above the rating listed in the “Absolute Maximum Ratings” table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the Operating sections of
this specification is not implied. Exposure to Absolute Maximum Rating conditions for
extended periods may affect device reliability. Refer also to the STMicroelectronics SURE
Program and other relevant quality documents.
Table 6.
Ablolute maximum ratings
Symbol
TA
Parameter
Value
Unit
–40 to +85
°C
–40 to +85
°C
–55 to +125
°C
260
°C
M41T315Y
–0.3 to +7.0
V
M41T315V/W
–0.3 to +4.6
V
–0.3 to VCC to +0.3
V
Operating temperature
®
TSTG
TSLD
(1)
Storage temperature (VCC, oscillator off)
SNAPHAT
SOIC
Lead solder temperature for 10 seconds
VCCI
Supply voltage (on any pin relative to Ground)
VIO
Input or output voltages
IO
Output current
20
mA
PD
Power dissipation
1
W
1. For SO package, Lead-free (Pb-free) lead finish: Reflow at peak temperature of 260°C (total thermal budget not to exceed
245°C for greater than 30 seconds).
Caution:
Negative undershoots below –0.3V are not allowed on any pin while in the Battery Back-up
mode.
Caution:
Do NOT wave solder SOIC to avoid damaging SNAPHAT sockets.
18/30
M41T315Y, M41T315V, M41T315W
5
DC and AC parameters
DC and AC parameters
This section summarizes the operating and measurement conditions, as well as the DC and
AC characteristics of the device. The parameters in the following DC and AC Characteristic
tables are derived from tests performed under the Measurement Conditions listed in the
relevant tables. Designers should check that the operating conditions in their projects match
the measurement conditions when using the quoted parameters.
Table 7.
DC and AC measurement conditions
Parameter
M41T315Y
M41T315V/W
4.5 to 5.5V
2.7 to 3.6V
–40 to +85°C
–40 to +85°C
Load capacitance (CL)
100pF
50pF
Input rise and fall times
≤ 5ns
≤ 5ns
0 to 3V
0 to 3V
1.5V
1.5V
VCC supply voltage
Ambient operating temperature
Input pulse voltages
Input and output timing ref. voltages
Figure 10. AC testing load circuit
400
DEVICE
UNDER
TEST
CL
CL includes JIG capacitance
Note:
2.0V
AI04255
50pF for M41T315V.
Table 8.
Capacitance
Parameter(1)(2)
Symbol
CIN
CIO
(3)
Min
Max
Unit
Input capacitance
10
pF
Input/output capacitance
10
pF
1. Effective capacitance measured with power supply at 5V; sampled only; not 100% tested.
2. At 25°C, f = 1MHz.
3. Outputs were deselected.
19/30
DC and AC parameters
Table 9.
Sym
M41T315Y, M41T315V, M41T315W
DC characteristics
Parameter
M41T315Y
M41T315V/W
–65
–85
Test condition(1)
Min
IIL(2)
Input leakage
current
IOL
Output leakage
current
Typ
VCC power supply
current
Min
Typ
Max
0V ≤ VIN ≤ VCC
±1
±1
µA
0V ≤ VOUT ≤ VCC
±1
±1
µA
10
6
mA
VCC0 = VCC1 – 0.3
150
100
mA
CEI = VIH
3
2
mA
CEI = VCC1 – 0.2
1
1
mA
ICC1(3) Supply current
ICCO1(4)
Max
Unit
ICC2(3)
Supply current
(TTL standby)
ICC3(3)
VCC power supply
current
VIL(5)
Input low voltage
–0.3
0.8
–0.3
0.6
V
VIH(5)
Input high voltage
2.2
VCC1 + 0.3
2.0
VCC +
0.3
V
VOL(6)
Output low voltage
0.4
V
VOH(6)
Output high
voltage
VPFD
Power fail
deselect
VSO
Battery back-up
switchover
VBAT
Battery voltage
VCEO
CEO output
voltage
IBAT(3)
Battery current
VBAT = 3.0V
TA = 25°C
VCC = 0V
0.5
0.5
µA
ICCO2(7)
Battery backup
current
VCC0 = VBAT – 0.2V
100
100
µA
IOL = 4.0 mA
IOH = –1.0 mA
0.4
2.4
2.4
4.25
4.50
2.80 (V)
2.60 (W)
VBAT
2.5
V
2.97 (V)
2.70 (W)
2.5
3.7
2.5
V
3.7
VCC1 – 0.2
or
VBAT – 0.2
VCC1 – 0.2
or
VBAT – 0.2
3. Measured without RAM connected.
4. ICCO1 is the maximum average load current the device can supply to external memory.
5. Voltages are referenced to Ground.
6. Measured with load shown in Figure 10 on page 19.
7. ICCO2 is the maximum average load current that the device can supply to memory in the battery backup mode.
20/30
V
V
1. Valid for ambient operating temperature: TA = –40 to 85°C; VCC = 4.5 to 5.5V or 2.7 to 3.6V (except where noted).
2. Applies to all input pins except RST, which is pulled internally to VCCI.
V
M41T315Y, M41T315V, M41T315W
Table 10.
DC and AC parameters
Crystal electrical characteristics (externally supplied)
Parameter(1)(2)
Symbol
fO
Resonant frequency
RS
Series resistance
CL
Load capacitance
Min
Typ
Max
Unit
32.768
kHz
60
kΩ
12.5
pF
1. These values are externally supplied. STMicroelectronics recommends the KDS DT-38:
1TA/1TC252E127, Tuning Fork Type (thruhole) or the DMX-26S: 1TJS125FH2A212, (SMD) quartz crystal
for industrial temperature operations. KDS can be contacted at kouhou@ kdsj.co.jp or
http://www.kdsj.co.jp for further information on this crystal type.
2. Load capacitors are integrated within the M41T315Y/V/W. Circuit board layout considerations for the
32.768kHz crystal of minimum trace lengths and isolation from RF generating signals should be taken into
account.
Figure 11. Power down/up mode AC waveforms
VCC
VPFD (max)
VPFD (min)
VSO
tR
tFB
tF
tREC
tPF
DON’T CARE
CEI
VBAT
tPD
0.2V
VBAT
0.2V
tPD
CEO
AI04257
Table 11.
Power down/up trip points DC characteristics
Parameter(1)(2)
Symbol
Min
Max
Unit
VPFD (max) to CEI low
1.5
2.5
ms
tF
VPFD (max) to VPFD (min) VCC fall time
300
µs
tFB
VPFD (min) to VSO VCC fall time
10
µs
tR
VPFD (min) to VPFD (max) VCC rise time
0
µs
tPF
CEI high to power-fail
0
µs
tPD(3)(4)
CEI propagation delay
tREC
M41T315Y
10
ns
M41T315V/W
15
ns
1. Valid for ambient operating temperature: TA = –40 to 85°C; VCC = 4.5 to 5.5V or 2.7 to 3.6V (except
where noted).
2. Measured at 25°C.
3. Measured with load shown in Figure 10 on page 19.
4. Input pulse rise and fall times equal 10ns
21/30
Package mechanical data
6
M41T315Y, M41T315V, M41T315W
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a lead-free second level interconnect. The category of
second Level Interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at: www.st.com.
22/30
M41T315Y, M41T315V, M41T315W
Package mechanical data
Figure 12. SO16 - 16-lead plastic small outline, package outline
A2
A
C
B
CP
e
D
N
E
H
1
A1
L
SO-b
Note:
Drawing is not to scale
Table 12.
SO16 - 16-lead plastic small outline (150 mils body width), package
mechanical data
mm
inches
Sym
Typ
Min
A
Max
Typ
Min
1.75
A1
0.10
A2
Max
0.069
0.25
0.004
1.60
0.010
0.063
B
0.35
0.46
0.014
0.018
C
0.19
0.25
0.007
0.010
D
9.80
10.00
0.386
0.394
E
3.30
4.00
0.150
0.158
-
-
-
-
H
5.80
6.20
0.228
0.244
L
0.40
1.27
0.016
0.050
a
0°
8°
0°
8°
N
16
e
CP
1.27
0.050
16
0.10
0.004
23/30
Package mechanical data
M41T315Y, M41T315V, M41T315W
Figure 13. SOH28 - 28-lead plastic small outline, package outline
A2
A
C
B
eB
e
CP
D
N
E
H
A1
L
1
SOH-A
Note:
Drawing is not to scale.
Table 13.
SOH28 - 28-lead plastic small outline, package mechanical data
mm
inches
Sym
Typ
Min
A
Typ
Min
3.05
Max
0.120
A1
0.05
0.36
0.002
0.014
A2
2.34
2.69
0.092
0.106
B
0.36
0.51
0.014
0.020
C
0.15
0.32
0.006
0.12
D
17.71
18.49
0.697
0.728
E
8.23
8.89
0.324
0.350
-
-
-
-
eB
3.20
3.61
0.126
0.142
H
11.51
12.70
0.453
0.500
L
0.41
1.27
0.016
0.050
a
0°
8°
0°
8°
N
28
e
CP
24/30
Max
1.27
0.050
28
0.10
0.004
M41T315Y, M41T315V, M41T315W
Package mechanical data
Figure 14. SH - 4-pin SNAPHAT housing for 48mAh battery and crystal, package
mechanical data
A1
A2
A
eA
A3
B
L
eB
D
E
SHTK-A
Table 14.
SH - 4-pin SNAPHAT housing for 48mAh battery and crystal, package
mechanical data
mm
inches
Sym
Typ
Min
A
Max
Typ
Min
Max
9.78
0
0.385
A1
6.73
7.24
0.265
0.285
A2
6.48
6.99
0.255
0.275
0.38
0
0.015
A3
B
0.46
0.56
0.018
0.022
D
21.21
21.84
0.835
0.860
E
14.22
14.99
0.560
0.590
eA
15.55
15.95
0.612
0.628
eB
3.20
3.61
0.126
0.142
L
2.03
2.29
0.080
0.090
25/30
Package mechanical data
M41T315Y, M41T315V, M41T315W
Figure 15. SH - 4-pin SNAPHAT housing for 120mAh battery and crystal, package
outline
A1
A2
A
eA
A3
B
L
eB
D
E
SHTK-A
Table 15.
SH - 4-pin SNAPHAT housing for 120mAh battery and crystal, package
mechanical data
mm
inches
Sym
Typ
Min
A
Typ
Min
Max
10.54
0
0.415
A1
8.00
8.51
0.315
0.335
A2
7.24
8.00
0.285
0.315
0.38
0
0.015
A3
26/30
Max
B
0.46
0.56
0.018
0.022
D
21.21
21.84
0.835
0.860
E
17.27
18.03
0.680
0.710
eA
15.55
15.95
0.612
0.628
eB
3.20
3.61
0.126
0.142
L
2.03
2.29
0.080
0.090
M41T315Y, M41T315V, M41T315W
7
Part numbering
Table 16.
Ordering information scheme
Example:
Part numbering
M41T
315Y
–65
MH
6
E
Device type
M41T
Supply voltage and write protect voltage
315Y(1) = VCC = 4.5 to 5.5V; VPFD = 4.25 to 4.50V
315V = VCC = 3.0 to 3.6V; VPFD = 2.80 to 2.97V
315W = VCC = 2.7 to 3.3V; VPFD = 2.60 to 2.70V
Speed
–65 = 65ns (315Y)
–85 = 85ns (315V/W)
Package
MH(2) = SOH28
MQ = SO16
Temperature range
6 = –40 to 85°C
Shipping method
For SOH28:
blank = Tubes (not for new design - use E)
E = Lead-free package (ECOPACK®), tubes
F = Lead-free package (ECOPACK®), tape & reel
TR = Tape & reel (not for new design - use F)
For SOH16:
blank = Tubes (not for new design - use E)
E = Lead-free package (ECOPACK®), tubes
F = Lead-free package (ECOPACK®), tape & reel
TR = Tape & reel (not for new design - use F)
1. Contact local sales office
2. The SOIC package (SOH28) requires the SNAPHAT® battery package which is ordered separately under the part number
“M4Txx-BR12SHX” in plastic tube or “M4TXX-BR12SHXTR” in tape & reel form (see Table 17 on page 28).
27/30
Part numbering
Caution:
M41T315Y, M41T315V, M41T315W
Do not place the SNAPHAT battery package “M4TXX-BR12SH” in conductive foam as it will
drain the lithium button-cell battery.
For other options, or for more information on any aspect of this device, please contact the
ST sales office nearest you.
Table 17.
28/30
SNAPHAT battery table
Part number
Description
Package
M48T28-BR12SH
Lithium battery (48mAh) SNAPHAT
SH
M48T32-BR12SH
Lithium battery (120mAh) SNAPHAT
SH
M41T315Y, M41T315V, M41T315W
8
Revision history
Revision history
Table 18.
Document revision history
Date
Revision
Changes
Jun-2001
1.0
First issue
17-Jul-2001
1.1
Basic formatting changes
18-Sep-2001
1.2
Changed pin 8 in 28-pin to VSS
27-Sep-2001
1.3
Added ambient temp to DC characteristics table (Table 9)
01-May-2002
1.4
Modify reflow time and temperature footnote (Table 6)
04-Nov-2002
1.5
Modify crystal electrical characteristics table footnotes (Table 10);
add marketing status (Table 16)
26-Mar-2003
1.6
Update test condition (Table 9)
08-Jun-2004
2.0
Reformatted; add lead-free information
26-Nov-2007
3
Reformatted document; product status Not for New Design; added
lead-free second level interconnect information to cover page and
Section 6: Package mechanical data; updated Table 6.
29/30
M41T315Y, M41T315V, M41T315W
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2007 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
30/30