M74HC279 QUAD S - R LATCH ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 13ns (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC =2µA(MAX.) at TA=25°C HIGH NOISE IMMUNITY: VNIH = V NIL = 28 % VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 4mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 279 DESCRIPTION The M74HC279 is an high speed CMOS QUAD S - R LATCH fabricated with silicon gate C 2MOS technology. DIP SOP TSSOP ORDER CODES PACKAGE TUBE DIP SOP TSSOP M74HC279B1R M74HC279M1R T&R M74HC279RM13TR M74HC279TTR All inputs are equipped with protection circuits against static discharge and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS August 2001 1/10 M74HC279 IINPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL NAME AND FUNCTION 1, 5, 10, 14 1R to 4R 1S1, 1S2, 2S, 3S1, 3S2, 4S 1Q to 4Q GND VCC Reset Inputs (Active Low) 2, 3, 6, 11, 12, 15 4, 7, 9, 13 8 16 Set Inputs (Active Low) Outputs Ground (0V) Positive Supply Voltage TRUTH TABLE S# R Q H L H L H H L L Q0 H L H NOTE : Q0 = The level of Q before the indicated input condition was established. # : For latches with double S input : H : Both S inputs high L : One of both inputs low LOGIC DIAGRAM This logic diagram has not be used to estimate propagation delays 2/10 M74HC279 ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Value Supply Voltage Unit -0.5 to +7 V -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 V DC Input Diode Current ± 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 25 mA ± 50 mA VI DC Input Voltage VO DC Output Voltage IIK ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) V 500(*) mW -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied (*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Value Supply Voltage Unit 2 to 6 V VI Input Voltage 0 to VCC V VO Output Voltage 0 to VCC V Top Operating Temperature -55 to 125 °C Input Rise and Fall Time tr, tf VCC = 2.0V 0 to 1000 ns VCC = 4.5V 0 to 500 ns VCC = 6.0V 0 to 400 ns 3/10 M74HC279 DC SPECIFICATIONS Test Condition Symbol VIH VIL VOH VOL II ICC Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Input Leakage Current Quiescent Supply Current Value TA = 25°C VCC (V) Min. 2.0 4.5 6.0 2.0 4.5 6.0 Typ. Max. 1.5 3.15 4.2 -40 to 85°C -55 to 125°C Min. Min. Max. 1.5 3.15 4.2 0.5 1.35 1.8 Max. 1.5 3.15 4.2 0.5 1.35 1.8 V 0.5 1.35 1.8 2.0 IO=-20 µA 1.9 2.0 1.9 1.9 4.5 IO=-20 µA 4.4 4.5 4.4 4.4 6.0 IO=-20 µA 5.9 6.0 5.9 5.9 4.5 IO=-4.0 mA 4.18 4.31 4.13 4.10 5.68 Unit V V 6.0 IO=-5.2 mA 2.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=20 µA 0.0 0.1 0.1 0.1 6.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=4.0 mA 0.17 0.26 0.33 0.40 6.0 IO=5.2 mA 0.18 0.26 0.33 0.40 6.0 VI = VCC or GND ± 0.1 ±1 ±1 µA 6.0 VI = VCC or GND 2 20 40 µA 5.8 5.63 5.60 V AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol Parameter tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time (S1, S2 - Q) tPLH tPHL Propagation Delay Time (S - Q) tPHL 4/10 Propagation Delay Time (R - Q) VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 Value TA = 25°C Min. Typ. Max. 30 8 7 45 15 13 38 12 10 42 14 12 75 15 13 130 26 22 100 20 17 120 24 20 -40 to 85°C -55 to 125°C Min. Min. Max. 95 19 16 165 33 28 125 25 21 150 30 26 Unit Max. 110 22 19 195 39 33 150 30 26 180 36 31 ns ns ns ns M74HC279 CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter VCC (V) Value TA = 25°C Min. Typ. Max. 10 CIN Input Capacitance 5.0 5 CPD Power Dissipation Capacitance (note 1) 5.0 18 -40 to 85°C -55 to 125°C Min. Min. Max. 10 Unit Max. 10 pF pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC TEST CIRCUIT CL = 50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM 1 : PROPAGATION DELAY TIME (f=1MHz; 50% duty cycle) 5/10 M74HC279 WAVEFORM 2 : PROPAGATION DELAY TIME (f=1MHz; 50% duty cycle) INPUT WAVEFORMS (f=1MHz; 50% duty cycle) 6/10 M74HC279 Plastic DIP-16 (0.25) MECHANICAL DATA mm. inch DIM. MIN. a1 0.51 B 0.77 TYP MAX. MIN. TYP. MAX. 0.020 1.65 0.030 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 17.78 0.700 F 7.1 0.280 I 5.1 0.201 L Z 3.3 0.130 1.27 0.050 P001C 7/10 M74HC279 SO-16 MECHANICAL DATA DIM. mm. MIN. TYP A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 9.8 10 0.385 0.393 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.62 0.024 8° (max.) PO13H 8/10 M74HC279 TSSOP16 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0° L 0.45 A 0.60 0.0256 BSC 8° 0° 0.75 0.018 8° 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080338D 9/10 M74HC279 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com 10/10