MAX202E–MAX213E, MAX232E/MAX241E LE AVAILAB ±15kV ESD-Protected, +5V RS-232 Transceivers General Description Next-Generation Device Features The MAX202E–MAX213E, MAX232E/MAX241E line drivers/receivers are designed for RS-232 and V.28 communications in harsh environments. Each transmitter output and receiver input is protected against ±15kV electrostatic discharge (ESD) shocks, without latchup. The various combinations of features are outlined in the Selector Guide. The drivers and receivers for all ten devices meet all EIA/TIA-232E and CCITT V.28 specifications at data rates up to 120kbps, when loaded in accordance with the EIA/TIA-232E specification. The MAX211E/MAX213E/MAX241E are available in 28pin SO packages, as well as a 28-pin SSOP that uses 60% less board space. The MAX202E/MAX232E come in 16-pin TSSOP, narrow SO, wide SO, and DIP packages. The MAX203E comes in a 20-pin DIP/SO package, and needs no external charge-pump capacitors. The MAX205E comes in a 24-pin wide DIP package, and also eliminates external charge-pump capacitors. The MAX206E/MAX207E/MAX208E come in 24-pin SO, SSOP, and narrow DIP packages. The MAX232E/MAX241E operate with four 1µF capacitors, while the MAX202E/MAX206E/MAX207E/MAX208E/ MAX211E/MAX213E operate with four 0.1µF capacitors, further reducing cost and board space. ♦ For Low-Voltage Applications MAX3222E/MAX3232E/MAX3237E/MAX3241E/ MAX3246E: ±15kV ESD-Protected Down to 10nA, +3.0V to +5.5V, Up to 1Mbps, True RS-232 Transceivers (MAX3246E Available in a UCSP™ Package) ♦ For Low-Power Applications MAX3221/MAX3223/MAX3243: 1µA Supply Current, True +3V to +5.5V RS-232 Transceivers with Auto-Shutdown™ ♦ For Space-Constrained Applications MAX3233E/MAX3235E: ±15kV ESD-Protected, 1µA, 250kbps, +3.0V/+5.5V, Dual RS-232 Transceivers with Internal Capacitors ♦ For Low-Voltage or Data Cable Applications MAX3380E/MAX3381E: +2.35V to +5.5V, 1µA, 2Tx/2Rx RS-232 Transceivers with ±15kV ESDProtected I/O and Logic Pins Ordering Information PART ________________________Applications Notebook, Subnotebook, and Palmtop Computers Battery-Powered Equipment Hand-Held Equipment TEMP RANGE PIN-PACKAGE MAX202ECPE 0°C to +70°C 16 Plastic DIP MAX202ECSE 0°C to +70°C 16 Narrow SO Ordering Information continued at end of data sheet. Pin Configurations and Typical Operating Circuits appear at end of data sheet. Functional Diagrams AutoShutdown and UCSP are trademarks of Maxim Integrated Products, Inc. Selector Guide PART NO. OF RS-232 DRIVERS NO. OF RS-232 RECEIVERS RECEIVERS ACTIVE IN SHUTDOWN NO. OF EXTERNAL CAPACITORS (µF) LOW-POWER SHUTDOWN TTL TRISTATE MAX202E 2 2 0 4 (0.1) No No MAX203E 2 2 0 None No No MAX205E 5 5 0 None Yes Yes MAX206E 4 3 0 4 (0.1) Yes Yes MAX207E 5 3 0 4 (0.1) No No MAX208E 4 4 0 4 (0.1) No No MAX211E 4 5 0 4 (0.1) Yes Yes 2 4 (0.1) Yes Yes 0 4 (1) No No 0 4 (1) Yes Yes MAX213E 4 5 Pin Configurations appear at MAX232E 2 end of data sheet. 2 Functional Diagrams continued at end of data sheet. MAX241E 4 5 UCSP is a trademark of Maxim Integrated Products, Inc. For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com. 19-0175; Rev 6; 3/05 MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers ABSOLUTE MAXIMUM RATINGS VCC..........................................................................-0.3V to +6V 20-Pin Plastic DIP (derate 11.11mW/°C above +70°C)...889mW 20-Pin SO (derate 10.00mW/°C above +70°C).............800mW 24-Pin Narrow Plastic DIP (derate 13.33mW/°C above +70°C) ...............................1.07W 24-Pin Wide Plastic DIP (derate 14.29mW/°C above +70°C) ................................1.14W 24-Pin SO (derate 11.76mW/°C above +70°C).............941mW 24-Pin SSOP (derate 8.00mW/°C above +70°C) ..........640mW 28-Pin SO (derate 12.50mW/°C above +70°C)....................1W 28-Pin SSOP (derate 9.52mW/°C above +70°C) ..........762mW Operating Temperature Ranges MAX2_ _EC_ _ .....................................................0°C to +70°C MAX2_ _EE_ _...................................................-40°C to +85°C Storage Temperature Range .............................-65°C to +165°C Lead Temperature (soldering, 10s) .................................+300°C V+ ................................................................(VCC - 0.3V) to +14V V- ............................................................................-14V to +0.3V Input Voltages T_IN ............................................................-0.3V to (V+ + 0.3V) R_IN ...................................................................................±30V Output Voltages T_OUT.................................................(V- - 0.3V) to (V+ + 0.3V) R_OUT ......................................................-0.3V to (VCC + 0.3V) Short-Circuit Duration, T_OUT....................................Continuous Continuous Power Dissipation (TA = +70°C) 16-Pin Plastic DIP (derate 10.53mW/°C above +70°C)....842mW 16-Pin Narrow SO (derate 8.70mW/°C above +70°C) .....696mW 16-Pin Wide SO (derate 9.52mW/°C above +70°C) ......762mW 16-Pin TSSOP (derate 9.4mW/°C above +70°C) ...........755mW Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VCC = +5V ±10% for MAX202E/206E/208E/211E/213E/232E/241E; VCC = +5V ±5% for MAX203E/205E/207E; C1–C4 = 0.1µF for MAX202E/206E/207E/208E/211E/213E; C1–C4 = 1µF for MAX232E/241E; TA = TMIN to TMAX; unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX MAX202E/203E 8 15 MAX205E–208E 11 20 MAX211E/213E 14 20 MAX232E 5 10 MAX241E 7 15 MAX205E/206E 1 10 MAX211E/241E 1 10 MAX213E 15 50 UNITS DC CHARACTERISTICS VCC Supply Current ICC Shutdown Supply Current No load, TA = +25°C TA = +25°C, Figure 1 mA µA LOGIC Input Pullup Current T_IN = 0V (MAX205E–208E/211E/213E/241E) 200 µA Input Leakage Current T_IN = 0V to VCC (MAX202E/203E/232E) ±10 µA T_IN; EN, SHDN (MAX213E) or EN, SHDN (MAX205E–208E/211E/241E) 0.8 V Input Threshold Low VIL Input Threshold High VIH Output-Voltage Low VOL R_OUT; IOUT = 3.2mA (MAX202E/203E/232E) or IOUT = 1.6mA (MAX205E/208E/211E/213E/241E) Output-Voltage High VOH R_OUT; IOUT = -1.0mA Output Leakage Current 2 15 T_IN 2.0 EN, SHDN (MAX213E) or EN, SHDN (MAX205E–208E/211E/241E) 2.4 EN = VCC, EN = 0V, 0V ≤ ROUT ≤ VCC, MAX205E–208E/211E/213E/241E outputs disabled V 0.4 3.5 VCC - 0.4 ±0.05 V V ±10 µA Maxim Integrated MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers ELECTRICAL CHARACTERISTICS (continued) (VCC = +5V ±10% for MAX202E/206E/208E/211E/213E/232E/241E; VCC = +5V ±5% for MAX203E/205E/207E; C1–C4 = 0.1µF for MAX202E/206E/207E/208E/211E/213E; C1–C4 = 1µF for MAX232E/241E; TA = TMIN to TMAX; unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL CONDITIONS MIN TYP -30 0.8 1.2 0.6 1.5 MAX UNITS 30 V EIA/TIA-232E RECEIVER INPUTS Input Voltage Range All parts, normal operation Input Threshold Low TA = +25°C, VCC = 5V Input Threshold High TA = +25°C, VCC = 5V Input Hysteresis VCC = 5V, no hysteresis in shutdown Input Resistance TA = +25°C, VCC = 5V MAX213E, SHDN = 0V, EN = VCC V All parts, normal operation 1.7 2.4 MAX213E (R4, R5), SHDN = 0V, EN = VCC 1.5 2.4 0.2 0.5 1.0 V 3 5 7 kΩ ±9 V EIA/TIA-232E TRANSMITTER OUTPUTS Output Voltage Swing All drivers loaded with 3kΩ to ground (Note 1) ±5 Output Resistance VCC = V+ = V- = 0V, VOUT = ±2V 300 Output Short-Circuit Current V Ω ±10 ±60 mA TIMING CHARACTERISTICS RL = 3kΩ to 7kΩ, CL = 50pF to 1000pF, one transmitter switching Maximum Data Rate 120 All parts, normal operation Receiver Propagation Delay tPLHR, tPHLR CL = 150pF MAX213E (R4, R5), SHDN = 0V, EN = VCC kbps 0.5 10 4 40 µs Receiver Output Enable Time MAX205E/206E/211E/213E/241E normal operation, Figure 2 600 ns Receiver Output Disable Time MAX205E/206E/211E/213E/241E normal operation, Figure 2 200 ns 2 µs Transmitter Propagation Delay Transition-Region Slew Rate tPLHT, tPHLT RL = 3kΩ, CL = 2500pF, all transmitters loaded TA = +25°C, VCC = 5V, RL = 3kΩ to 7kΩ, CL = 50pF to 1000pF, measured from -3V to +3V or +3V to -3V, Figure 3 3 6 30 V/µs ESD PERFORMANCE: TRANSMITTER OUTPUTS, RECEIVER INPUTS Human Body Model ESD-Protection Voltage ±15 IEC1000-4-2, Contact Discharge ±8 IEC1000-4-2, Air-Gap Discharge ±5%. Note 1: MAX211EE_ _ and MAX213EE_ _ tested with VCC = +5V ±15 kV Note 1: MAX211EE_ _ tested with VCC = +5V ±5%. Maxim Integrated 3 MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers __________________________________________Typical Operating Characteristics (Typical Operating Circuits, VCC = +5V, TA = +25°C, unless otherwise noted.) 8.0 7.0 VOH, -VOL (V) 6.5 VCC = 5.0V VOH, -VOL (V) 7.0 VCC = 5.5V VCC = 5.5V 6.5 VCC = 5.0V VCC = 4.5V VCC = 4.5V 5.0 5.0 1000 2000 3000 4000 0 5000 1000 2000 3000 4000 2000 3000 4000 5000 LOAD CAPACITANCE (pF) 30 7.0 VCC = 5.5V 6.0 ALL TRANSMITTERS LOADED DATA RATE = 120kbps RL = 3kΩ 25 SLEW RATE ( V/μs) ALL TRANSMITTERS LOADED DATA RATE = 120kbps RL = 3kΩ MAX202E-TOC4 8.0 6.5 1000 MAX211E/MAX213E/MAX241E TRANSMITTER SLEW RATE vs. LOAD CAPACITANCE MAX211E/MAX213E TRANSMITTER OUTPUT VOLTAGE vs. LOAD CAPACITANCE 7.5 0 5000 LOAD CAPACITANCE (pF) LOAD CAPACITANCE (pF) VOH, -VOL (V) VCC = 5.0V VCC = 4.5V 5.0 0 6.5 5.5 5.5 5.5 VCC = 5.5V 6.0 6.0 6.0 ALL TRANSMITTERS LOADED DATA RATE = 120kbps RL = 3kΩ 7.5 MAX202E-TOC3 7.5 7.0 VOH, -VOL (V) ALL TRANSMITTERS LOADED DATA RATE = 120kbps RL = 3kΩ MAX202E-TOC5 ALL TRANSMITTERS LOADED DATA RATE = 120kbps RL = 3kΩ MAX202E-TOC2 8.0 MAX202E-TOC1 8.0 7.5 MAX241E TRANSMITTER OUTPUT VOLTAGE vs. LOAD CAPACITANCE MAX202E/MAX203E TRANSMITTER OUTPUT VOLTAGE vs. LOAD CAPACITANCE MAX232E TRANSMITTER OUTPUT VOLTAGE vs. LOAD CAPACITANCE 20 15 10 -SLEW RATE 5 5.5 +SLEW RATE VCC = 4.5V 5.0 0 1000 VCC = 5.0V 2000 3000 LOAD CAPACITANCE (pF) 4 4000 0 5000 0 1000 2000 3000 4000 5000 LOAD CAPACITANCE (pF) Maxim Integrated MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers ____________________________Typical Operating Characteristics (continued) (Typical Operating Circuits, VCC = +5V, TA = +25°C, unless otherwise noted.) MAX205E–MAX208E TRANSMITTER OUTPUT VOLTAGE vs. LOAD CAPACITANCE 8 -SLEW RATE 6 120kbps 2.5 VCC = +4.5V, RL = 3kΩ 1 TRANSMITTER AT FULL DATA RATE 4 TRANSMITTERS AT 1/8 DATA RATE -2.5 14 12 4 2 20kbps 0 1000 2000 3000 4000 -7.5 5000 0 0 1000 LOAD CAPACITANCE (pF) 2000 3000 4000 5000 SUPPLY CURRENT (mA) 40 120kbps 35 20kbps 30 VCC = +4.5V, RL = 3kΩ 1 TRANSMITTER AT FULL DATA RATE 4 TRANSMITTERS AT 1/8 DATA RATE 2000 3000 4000 LOAD CAPACITANCE (pF) Maxim Integrated 3000 4000 5000 V+ 7.5 VOUT+ 5.0 2.5 VCC = +4.5V, RL = 3kΩ 1 TRANSMITTER AT FULL DATA RATE 4 TRANSMITTERS AT 1/8 DATA RATE 0 -2.5 -5.0 VOUT- -7.5 V- -10.0 20 1000 2000 LOAD CAPACITANCE (pF) 10.0 OUTPUT VOLTAGE (V) 240kbps 45 1000 MAX205E–MAX208E OUTPUT VOLTAGE vs. DATA RATE MAX202E TOC-09 50 0 0 LOAD CAPACITANCE (pF) MAX205E–MAX208E SUPPLY CURRENT vs. LOAD CAPACITANCE 25 FALL 8 120kbps -5.0 2 RISE 10 6 240kbps +SLEW RATE 4 16 240kbps 0 VCC = +4.5V, RL = 3kΩ 1 TRANSMITTER AT FULL DATA RATE 4 TRANSMITTERS AT 1/8 DATA RATE MAX202E TOC-08 5.0 20 18 MAX202E TOC-10 10 20kbps SLEW RATE (V/μs) SLEW RATE ( V/μs) 12 7.5 OUTPUT VOLTAGE (V) ALL TRANSMITTERS LOADED DATA RATE = 120kbps RL = 3kΩ MAX202E-TOC6 14 MAX205E–MAX208E TRANSMITTER SLEW RATE vs. LOAD CAPACITANCE MAX202E TOC-07 MAX202E/MAX203E/MAX232E TRANSMITTER SLEW RATE vs. LOAD CAPACITANCE 5000 0 30 60 90 120 150 180 210 240 DATA RATE (kbps) 5 MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers _____________________________________________________________Pin Descriptions MAX202E/MAX232E PIN DIP/SO/TSSOP 1, 3 2 4, 5 6 7, 14 8, 13 9, 12 10, 11 15 16 __ LCC 2, 4 3 5, 7 8 9, 18 10, 17 12, 15 13, 14 19 20 1, 6, 11, 16 NAME C1+, C1V+ C2+, C2VT_OUT R_IN R_OUT T_IN GND VCC N.C. FUNCTION Terminals for Positive Charge-Pump Capacitor +2VCC Voltage Generated by the Charge Pump Terminals for Negative Charge-Pump Capacitor -2VCC Voltage Generated by the Charge Pump RS-232 Driver Outputs RS-232 Receiver Inputs RS-232 Receiver Outputs RS-232 Driver Inputs Ground +4.5V to +5.5V Supply-Voltage Input No Connection—Not Internally Connected MAX203E PIN DIP 1, 2 3, 20 4,19 5,18 6, 9 7 8 10, 16 12, 17 13 14 11, 15 SO 1, 2 3, 20 4, 19 5, 18 6, 9 7 13 11, 16 10, 17 14 8 12, 15 NAME T_IN R_OUT R_IN T_OUT GND VCC C1+ C2VC1V+ C2+ FUNCTION RS-232 Driver Inputs RS-232 Receiver Outputs RS-232 Receiver Inputs RS-232 Transmitter Outputs Ground +4.5V to +5.5V Supply-Voltage Input Make no connection to this pin. Connect pins together. -2VCC Voltage Generated by the Charge Pump. Connect pins together. Make no connection to this pin. +2VCC Voltage Generated by the Charge Pump Connect pins together. MAX205E PIN 1–4, 19 5, 10, 13, 18, 24 6, 9, 14, 17, 23 NAME T_OUT R_IN R_OUT 7, 8, 15, 16, 22 11 12 T_IN GND VCC TTL/CMOS Driver Inputs. Internal pullups to VCC. Ground +4.75V to +5.25V Supply Voltage 20 EN SHDN Receiver Enable—Active Low 21 6 FUNCTION RS-232 Driver Outputs RS-232 Receiver Inputs TTL/CMOS Receiver Outputs. All receivers are inactive in shutdown. Shutdown Control—Active High Maxim Integrated MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers ________________________________________________Pin Descriptions (continued) MAX206E PIN 1, 2, 3, 24 4, 16, 23 5, 17, 22 NAME T_OUT R_IN R_OUT 6, 7, 18, 19 8 9 T_IN GND VCC TTL/CMOS Driver Inputs. Internal pullups to VCC. Ground +4.5V to +5.5V Supply Voltage 10, 12 C1+, C1- Terminals for Positive Charge-Pump Capacitor 11 13, 14 V+ C2+, C2- +2VCC Generated by the Charge Pump Terminals for Negative Charge-Pump Capacitor 15 V- 20 EN SHDN 21 FUNCTION RS-232 Driver Outputs RS-232 Receiver Inputs TTL/CMOS Receiver Outputs. All receivers are inactive in shutdown. -2VCC Generated by the Charge Pump Receiver Enable—Active Low Shutdown Control—Active High MAX207E PIN 1, 2, 3, 20, 24 4, 16, 23 5, 17, 22 NAME T_OUT R_IN R_OUT FUNCTION RS-232 Driver Outputs RS-232 Receiver Inputs TTL/CMOS Receiver Outputs. All receivers are inactive in shutdown. 6, 7, 18, 19, 21 8 9 T_IN GND VCC TTL/CMOS Driver Inputs. Internal pullups to VCC. Ground +4.75V to +5.25V Supply Voltage 10, 12 C1+, C1- Terminals for Positive Charge-Pump Capacitor 11 13, 14 V+ C2+, C2- +2VCC Generated by the Charge Pump Terminals for Negative Charge-Pump Capacitor 15 V- -2VCC Generated by the Charge Pump MAX208E PIN 1, 2, 20, 24 3, 7, 16, 23 4, 6, 17, 22 NAME T_OUT R_IN R_OUT 5, 18, 19, 21 8 9 T_IN GND VCC TTL/CMOS Driver Inputs. Internal pullups to VCC. Ground +4.5V to +5.5V Supply Voltage 10, 12 C1+, C1- Terminals for Positive Charge-Pump Capacitor 11 13, 14 V+ C2+, C2- +2VCC Generated by the Charge Pump Terminals for Negative Charge-Pump Capacitor 15 V- Maxim Integrated FUNCTION RS-232 Driver Outputs RS-232 Receiver Inputs TTL/CMOS Receiver Outputs. All receivers are inactive in shutdown. -2VCC Generated by the Charge Pump 7 MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers ________________________________________________Pin Descriptions (continued) MAX211E/MAX213E/MAX241E PIN 1, 2, 3, 28 4, 9, 18, 23, 27 NAME T_OUT R_IN 5, 8, 19, 22, 26 R_OUT 6, 7, 20, 21 10 11 12, 14 13 15, 16 17 T_IN GND VCC C1+, C1V+ C2+, C2V- 24 25 FUNCTION RS-232 Driver Outputs RS-232 Receiver Inputs TTL/CMOS Receiver Outputs. For the MAX213E, receivers R4 and R5 are active in shutdown mode when EN = 1. For the MAX211E and MAX241E, all receivers are inactive in shutdown. TTL/CMOS Driver Inputs. Only the MAX211E, MAX213E, and MAX241E have internal pullups to VCC. Ground +4.5V to +5.5V Supply Voltage Terminals for Positive Charge-Pump Capacitor +2VCC Voltage Generated by the Charge Pump Terminals for Negative Charge-Pump Capacitor -2VCC Voltage Generated by the Charge Pump EN Receiver Enable—Active Low (MAX211E, MAX241E) EN Receiver Enable—Active High (MAX213E) SHDN Shutdown Control—Active High (MAX211E, MAX241E) SHDN Shutdown Control—Active Low (MAX213E) ISHDN +5.5V 0.1μF* EN INPUT 0.1μF* +3V 0V VCC C1+ 0.1μF* 0.1μF* C1C2+ V CC C2- MAX206E MAX211E MAX213E MAX241E 400kΩ +5.5V T_IN +5.5V (0V) OUTPUT ENABLE TIME 0.1μF* +3.5V VRECEIVER OUTPUT CL = 150pF +0.8V +3V T1 TO T5 T_OUT R1 TO R5 R_OUT 0V OR +5.5V DRIVE V+ EN (EN) 3kΩ R_IN +5.5V 5kΩ SHDN (SHDN) NOTE: POLARITY OF EN IS REVERSED FOR THE MAX213E EN INPUT RECEIVER OUTPUTS 0V OUTPUT DISABLE TIME VOH VOL VOH - 0.1V RL = 1kΩ +2.5V VOL + 0.1V GND ( ) ARE FOR MAX213E * 1μF FOR MAX241E CAPACITORS MAY BE POLARIZED OR UNPOLARIZED Figure 1. Shutdown-Current Test Circuit (MAX206E, MAX211E/MAX213E/MAX241E) 8 Figure 2. Receiver Output Enable and Disable Timing (MAX205E/MAX206E/MAX211E/MAX213E/MAX241E) Maxim Integrated MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers +5V 0.1μF* +5V 0.1μF* 0.1μF* VCC C1+ 0.1μF* C2- 0.1μF* 400kΩ T_ T_IN 0V (+5V) 0V (+5V) EN (EN) V- 0.1μF* C2+ V CC C2400kΩ T_ T_OUT R_ R_OUT MAX2_ _E C1- V- C2+ V CC 0.1μF* V+ 0.1μF* 0.1μF* MAX2_ _E VCC C1+ V+ C1- 0.1μF* R_IN T_IN 3kΩ 2500pF 5kΩ R_ R_OUT 0V (+5V) 0V (+5V) SHDN (SHDN) MINIMUM SLEW-RATE TEST CIRCUIT EN (EN) T_OUT R_IN 7kΩ 50pF 5kΩ SHDN (SHDN) MAXIMUM SLEW-RATE TEST CIRCUIT ( ) ARE FOR MAX213E * 1μF FOR MAX232E/MAX241E TRANSMITTER INPUT PULL-UP RESISTORS, ENABLE, AND SHUTDOWN ARE NOT PROVIDED ON THE MAX202E, MAX203E, AND MAX232E. ENABLE AND SHUTDOWN ARE NOT PROVIDED ON THE MAX207E AND MAX208E. Figure 3. Transition Slew-Rate Circuit _______________Detailed Description The MAX202E–MAX213E, MAX232E/MAX241E consist of three sections: charge-pump voltage converters, drivers (transmitters), and receivers. These E versions provide extra protection against ESD. They survive ±15kV discharges to the RS-232 inputs and outputs, tested using the Human Body Model. When tested according to IEC1000-4-2, they survive ±8kV contactdischarges and ±15kV air-gap discharges. The rugged E versions are intended for use in harsh environments or applications where the RS-232 connection is frequently changed (such as notebook computers). The standard (non-“E”) MAX202, MAX203, MAX205– MAX208, MAX211, MAX213, MAX232, and MAX241 are recommended for applications where cost is critical. +5V to ±10V Dual Charge-Pump Voltage Converter The +5V to ±10V conversion is performed by dual charge-pump voltage converters (Figure 4). The first charge-pump converter uses capacitor C1 to double the +5V into +10V, storing the +10V on the output filter capacitor, C3. The second uses C2 to invert the +10V Maxim Integrated into -10V, storing the -10V on the V- output filter capacitor, C4. In shutdown mode, V+ is internally connected to VCC by a 1kΩ pull-down resistor, and V- is internally connected to ground by a 1kΩ pull up resistor. RS-232 Drivers With VCC = 5V, the typical driver output voltage swing is ±8V when loaded with a nominal 5kΩ RS-232 receiver. The output swing is guaranteed to meet EIA/TIA-232E and V.28 specifications that call for ±5V minimum output levels under worst-case conditions. These include a 3kΩ load, minimum V CC , and maximum operating temperature. The open-circuit output voltage swings from (V+ - 0.6V) to V-. Input thresholds are CMOS/TTL compatible. The unused drivers’ inputs on the MAX205E–MAX208E, MAX211E, MAX213E, and MAX241E can be left unconnected because 400kΩ pull up resistors to VCC are included on-chip. Since all drivers invert, the pull up resistors force the unused drivers’ outputs low. The MAX202E, MAX203E, and MAX232E do not have pull up resistors on the transmitter inputs. 9 MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers V+ S1 S2 C1+ VCC C1 S3 S5 C3 IL + S4 GND C1- C2+ S6 C2 RL + C4 S7 VCC GND IL- S8 VC2- PART fCLK RL- MAX202E MAX203E MAX205E–208E MAX211E/213E MAX232E MAX241E fCLK (kHz) 230 230 200 200 140 30 Figure 4. Charge-Pump Diagram When in low-power shutdown mode, the MAX205E/ MAX206E/MAX211E/MAX213E/MAX241E driver outputs are turned off and draw only leakage currents—even if they are back-driven with voltages between 0V and 12V. Below -0.5V in shutdown, the transmitter output is diode-clamped to ground with a 1kΩ series impedance. RS-232 Receivers The receivers convert the RS-232 signals to CMOS-logic output levels. The guaranteed 0.8V and 2.4V receiver input thresholds are significantly tighter than the ±3V thresholds required by the EIA/TIA-232E specification. This allows the receiver inputs to respond to TTL/CMOSlogic levels, as well as RS-232 levels. The guaranteed 0.8V input low threshold ensures that receivers shorted to ground have a logic 1 output. The 5kΩ input resistance to ground ensures that a receiver with its input left open will also have a logic 1 output. Receiver inputs have approximately 0.5V hysteresis. This provides clean output transitions, even with slow rise/fall-time signals with moderate amounts of noise and ringing. In shutdown, the MAX213E’s R4 and R5 receivers have no hysteresis. 10 Shutdown and Enable Control (MAX205E/MAX206E/MAX211E/ MAX213E/MAX241E) In shutdown mode, the charge pumps are turned off, V+ is pulled down to VCC, V- is pulled to ground, and the transmitter outputs are disabled. This reduces supply current typically to 1µA (15µA for the MAX213E). The time required to exit shutdown is under 1ms, as shown in Figure 5. Receivers All MAX213E receivers, except R4 and R5, are put into a high-impedance state in shutdown mode (see Tables 1a and 1b). The MAX213E’s R4 and R5 receivers still function in shutdown mode. These two awake-inshutdown receivers can monitor external activity while maintaining minimal power consumption. The enable control is used to put the receiver outputs into a high-impedance state, to allow wire-OR connection of two EIA/TIA-232E ports (or ports of different types) at the UART. It has no effect on the RS-232 drivers or the charge pumps. Note: The enable control pin is active low for the MAX211E/MAX241E (EN), but is active high for the MAX213E (EN). The shutdown control pin is active high for the MAX205E/MAX206E/MAX211E/MAX241E (SHDN), but is active low for the MAX213E (SHDN). Maxim Integrated MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers The MAX213E’s receiver propagation delay is typically 0.5µs in normal operation. In shutdown mode, propagation delay increases to 4µs for both rising and falling transitions. The MAX213E’s receiver inputs have approximately 0.5V hysteresis, except in shutdown, when receivers R4 and R5 have no hysteresis. When entering shutdown with receivers active, R4 and R5 are not valid until 80µs after SHDN is driven low. When coming out of shutdown, all receiver outputs are invalid until the charge pumps reach nominal voltage levels (less than 2ms when using 0.1µF capacitors). ±15kV ESD Protection As with all Maxim devices, ESD-protection structures are incorporated on all pins to protect against electrostatic discharges encountered during handling and assembly. The driver outputs and receiver inputs have extra protection against static electricity. Maxim’s engineers developed state-of-the-art structures to protect these pins against ESD of ±15kV without damage. The ESD structures withstand high ESD in all states: normal operation, shutdown, and powered down. After an ESD event, Maxim’s E versions keep working without latchup, whereas competing RS-232 products can latch and must be powered down to remove latchup. ESD protection can be tested in various ways; the transmitter outputs and receiver inputs of this product family are characterized for protection to the following limits: 1) ±15kV using the Human Body Model 2) ±8kV using the contact-discharge method specified in IEC1000-4-2 3) ±15kV using IEC1000-4-2’s air-gap method. ESD Test Conditions ESD performance depends on a variety of conditions. Contact Maxim for a reliability report that documents test set-up, test methodology, and test results. Human Body Model Figure 6a shows the Human Body Model, and Figure 6b shows the current waveform it generates when discharged into a low impedance. This model consists of a 100pF capacitor charged to the ESD voltage of interest, which is then discharged into the test device through a 1.5kΩ resistor. MAX211E 3V SHDN 0V 10V V+ 5V 0V V- -5V -10V 200μs/div Figure 5. MAX211E V+ and V- when Exiting Shutdown (0.1µF capacitors) Table 1a. MAX205E/MAX206E/MAX211E/ MAX241E Control Pin Configurations SHDN EN OPERATION STATUS Tx Rx 0 0 Normal Operation All Active All Active 0 1 Normal Operation All Active All High-Z 1 X Shutdown All High-Z All High-Z X = Don't care. Table 1b. MAX213E Control Pin Configurations SHDN EN OPERATION STATUS Rx Tx 1–4 1–3 4, 5 0 0 Shutdown All High-Z High-Z High-Z 0 1 Shutdown All High-Z High-Z Active* 1 0 Normal Operation All Active High-Z High-Z 1 1 Normal Operation All Active Active Active *Active = active with reduced performance Maxim Integrated 11 MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers RC 1MΩ CHARGE-CURRENTLIMIT RESISTOR HIGHVOLTAGE DC SOURCE RD 1500Ω IP 100% 90% DISCHARGE RESISTANCE Ir PEAK-TO-PEAK RINGING (NOT DRAWN TO SCALE) AMPERES Cs 100pF STORAGE CAPACITOR DEVICE UNDER TEST 36.8% 10% 0 0 TIME tRL tDL CURRENT WAVEFORM Figure 6b. Human Body Model Current Waveform Figure 6a. Human Body ESD Test Model I RD 330Ω CHARGE-CURRENTLIMIT RESISTOR DISCHARGE RESISTANCE Cs 150pF STORAGE CAPACITOR 100% 90% DEVICE UNDER TEST I PEAK HIGHVOLTAGE DC SOURCE RC 50MΩ to 100MΩ 10% Figure 7a. IEC1000-4-2 ESD Test Model t r = 0.7ns to 1ns t 30ns 60ns IEC1000-4-2 The IEC1000-4-2 standard covers ESD testing and performance of finished equipment; it does not specifically refer to integrated circuits. The MAX202E/MAX203E–MAX213E, MAX232E/MAX241E help you design equipment that meets level 4 (the highest level) of IEC1000-4-2, without the need for additional ESD-protection components. The major difference between tests done using the Human Body Model and IEC1000-4-2 is higher peak current in IEC1000-4-2, because series resistance is lower in the IEC1000-4-2 model. Hence, the ESD withstand voltage measured to IEC1000-4-2 is generally lower than that measured using the Human Body Model. Figure 7b shows the current waveform for the 8kV IEC1000-4-2 level-four ESD contact-discharge test. 12 Figure 7b. IEC1000-4-2 ESD Generator Current Waveform The air-gap test involves approaching the device with a charged probe. The contact-discharge method connects the probe to the device before the probe is energized. Machine Model The Machine Model for ESD tests all pins using a 200pF storage capacitor and zero discharge resistance. Its objective is to emulate the stress caused by contact that occurs with handling and assembly during manufacturing. Of course, all pins require this protection during manufacturing, not just RS-232 inputs and outputs. Therefore, after PC board assembly, the Machine Model is less relevant to I/O ports. Maxim Integrated MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers __________Applications Information Capacitor Selection The capacitor type used for C1–C4 is not critical for proper operation. The MAX202E, MAX206–MAX208E, MAX211E, and MAX213E require 0.1µF capacitors, and the MAX232E and MAX241E require 1µF capacitors, although in all cases capacitors up to 10µF can be used without harm. Ceramic, aluminumelectrolytic, or tantalum capacitors are suggested for the 1µF capacitors, and ceramic dielectrics are suggested for the 0.1µF capacitors. When using the minimum recommended capacitor values, make sure the capacitance value does not degrade excessively as the operating temperature varies. If in doubt, use capacitors with a larger (e.g., 2x) nominal value. The capacitors’ effective series resistance (ESR), which usually rises at low temperatures, influences the amount of ripple on V+ and V-. Use larger capacitors (up to 10µF) to reduce the output impedance at V+ and V-. This can be useful when “stealing” power from V+ or from V-. The MAX203E and MAX205E have internal charge-pump capacitors. Bypass V CC to ground with at least 0.1µF. In applications sensitive to power-supply noise generated by the charge pumps, decouple VCC to ground with a capacitor the same size as (or larger than) the chargepump capacitors (C1–C4). V+ and V- as Power Supplies A small amount of power can be drawn from V+ and V-, although this will reduce both driver output swing and noise margins. Increasing the value of the charge-pump capacitors (up to 10µF) helps maintain performance when power is drawn from V+ or V-. Driving Multiple Receivers Each transmitter is designed to drive a single receiver. Transmitters can be paralleled to drive multiple receivers. Driver Outputs when Exiting Shutdown The driver outputs display no ringing or undesirable transients as they come out of shutdown. High Data Rates These transceivers maintain the RS-232 ±5.0V minimum driver output voltages at data rates of over 120kbps. For data rates above 120kbps, refer to the Transmitter Output Voltage vs. Load Capacitance graphs in the Typical Operating Characteristics . Communication at these high rates is easier if the capacitive loads on the transmitters are small; i.e., short cables are best. Table 2. Summary of EIA/TIA-232E, V.28 Specifications PARAMETER EIA/TIA-232E, V.28 SPECIFICATIONS CONDITIONS 0 Level 3kΩ to 7kΩ load +5V to +15V 1 Level 3kΩ to 7kΩ load -5V to -15V Driver Output Level, Max No load ±25V Data Rate 3kΩ ≤ RL ≤ 7kΩ, CL ≤ 2500pF Up to 20kbps Driver Output Voltage 0 Level +3V to +15V 1 Level -3V to -15V Receiver Input Voltage Receiver Input Level Instantaneous Slew Rate, Max ±25V 3kΩ ≤ RL ≤ 7kΩ, CL ≤ 2500pF Driver Output Short-Circuit Current, Max 30V/µs 100mA V.28 1ms or 3% of the period EIA/TIA-232E 4% of the period -2V < VOUT < +2V 300Ω Transition Rate on Driver Output Driver Output Resistance Maxim Integrated 13 MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers Table 3. DB9 Cable Connections Commonly Used for EIA/TIA-232E and V.24 Asynchronous Interfaces PIN CONNECTION 1 Received Line Signal Detector (sometimes called Carrier Detect, DCD) Handshake from DCE 2 Receive Data (RD) Data from DCE 3 Transmit Data (TD) Data from DTE 4 Data Terminal Ready Handshake from DTE 5 Signal Ground Reference point for signals 6 Data Set Ready (DSR) Handshake from DCE 7 Request to Send (RTS) Handshake from DTE 8 Clear to Send (CTS) Handshake from DCE 9 Ring Indicator Handshake from DCE ____________Pin Configurations and Typical Operating Circuits (continued) +5V INPUT TOP VIEW 0.1μF* 6.3V 0.1μF 1 0.1μF* 6.3V 3 4 C1+ 1 16 VCC V+ 2 15 GND C1- 3 C2+ 4 C2- 5 0.1μF* 16V 5 C1+ 16 VCC V+ +5V TO +10V C1- VOLTAGE DOUBLER C2+ +10V TO -10V C2- VOLTAGE INVERTER V- 2 +10V 6 -10V 0.1μF* 16V 14 T1OUT MAX202E MAX232E 12 R1OUT V- 6 11 T1IN T2OUT 7 10 T2IN R2IN 8 11 13 R1IN 9 T1OUT 14 T1 TTL/CMOS INPUTS R2OUT DIP/SO/TSSOP T1IN RS-232 OUTPUTS 10 T2IN 12 R1OUT T2OUT T2 R1 TTL/CMOS OUTPUTS 7 R1IN 13 5kΩ 9 R2OUT R2 R2IN 8 RS-232 INPUTS 5kΩ PIN NUMBERS ON TYPICAL OPERATING CIRCUIT REFER TO DIP/SO/TSSOP PACKAGE, NOT LCC. * 1.0μF CAPACITORS, MAX232E ONLY. 14 GND 15 Maxim Integrated MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers ____________Pin Configurations and Typical Operating Circuits (continued) +5V INPUT TOP VIEW 0.1μF 7 VCC +5V 400kΩ 19 R2IN T1IN 2 R1OUT 3 GND MAX203E 16 C215 C2+ 6 5 RS-232 OUTPUTS 400kΩ 1 T2IN 3 R1OUT T2OUT T2 R1IN R1 TTL/CMOS OUTPUTS 18 R2OUT R2IN R2 13 C1- (C1+) 8 12 V- (C2+) 11 C2+ (C2-) C2- (V-) 10 DIP/SO RS-232 INPUTS 19 5kΩ DO NOT MAKE CONNECTION TO THESE PINS INTERNAL -10V POWER SUPPLY INTERNAL +10V POWER SUPPLY PIN NUMBERS IN () ARE FOR SO PACKAGE. 4 5kΩ 20 14 V+ (C1-) GND 9 Maxim Integrated T1OUT T1 +5V 17 V- VCC 7 C1+ (V+) T1IN TTL/CMOS INPUTS 18 T2OUT R1IN 4 T1OUT 5 2 20 R2OUT T2IN 1 8(13) 13(14) 12(10) 17 14(8) C1+ C2+ C1- C2+ V- C2- V- C2- V+ GND 6 11 (12) 15 16 10 (11) GND 9 15 MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers ____________Pin Configurations and Typical Operating Circuits (continued) +5V INPUT 0.1μF TOP VIEW 12 VCC +5V 400kΩ 8 T1IN T1 T1OUT 3 +5V 400kΩ 7 T2IN T2 T2OUT 4 +5V 400kΩ T4OUT 1 24 R3IN T3OUT 2 23 R3OUT T1OUT 3 22 T5IN T2OUT 4 21 SHDN R2IN 5 20 EN R2OUT 6 T2IN 7 18 R4IN MAX205E TTL/CMOS INPUTS 15 T3IN T1IN 8 17 R4OUT 9 16 T4IN R1IN 10 15 T3IN GND 11 14 R5OUT VCC 12 13 R5IN T3OUT 2 RS-232 OUTPUTS +5V 400kΩ 16 T4IN T4 T4OUT 1 +5V 400kΩ 19 T5OUT R1OUT T3 22 T5IN 9 R1OUT T5 R1 T5OUT 19 R1IN 10 5kΩ 6 R2OUT R2 R2IN 5 5kΩ DIP TTL/CMOS OUTPUTS 23 R3OUT R3 R3IN 24 RS-232 INPUTS 5kΩ 17 R4OUT R4 R4IN 18 5kΩ 14 R5OUT R5 R5IN 13 5kΩ 20 EN SHDN 21 GND 11 16 Maxim Integrated MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers ____________Pin Configurations and Typical Operating Circuits (continued) TOP VIEW +5V INPUT 0.1μF 6.3V 0.1μF 10 0.1μF 6.3V 0.1μF 16V 9 VCC C1+ V+ 11 +5V TO +10V VOLTAGE DOUBLER 12 C113 C2+ +10V TO -10V VOLTAGE INVERTER 14 C2- 0.1μF 16V V- 15 +5V 400kΩ T3OUT 1 24 T4OUT T1OUT 2 23 R2IN T2OUT 3 22 R2OUT R1IN 4 21 SHDN R1OUT 5 20 EN T2IN 6 19 T4IN T1IN 7 18 T3IN GND 8 17 R3OUT VCC 9 16 R3IN C1+ 10 15 V- V+ 11 14 C2- C1- 12 13 C2+ 7 T1IN T1 T1OUT 2 +5V MAX206E 400kΩ 6 T2IN T2 T2OUT 3 +5V TTL/CMOS INPUTS RS-232 OUTPUTS 400kΩ 18 T3IN T3 T3OUT 1 +5V 400kΩ 19 T4IN 5 R1OUT T4 R1 T4OUT 24 R1IN 4 5kΩ DIP/SO/SSOP TTL/CMOS OUTPUTS 22 R2OUT R2 R2IN 23 RS-232 INPUTS 5kΩ 17 R3OUT R3 R3IN 16 5kΩ 20 EN SHDN 21 GND 8 Maxim Integrated 17 MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers ____________Pin Configurations and Typical Operating Circuits (continued) +5V INPUT TOP VIEW 0.1μF 6.3V 0.1μF 10 9 VCC C1+ 0.1μF 6.3V 12 C113 C2+ 0.1μF 16V 14 C2- V+ 11 +5V TO +10V VOLTAGE DOUBLER +10V TO -10V VOLTAGE INVERTER 0.1μF 16V V- 15 +5V 400kΩ 7 T1IN T1 T1OUT 2 +5V 400kΩ T3OUT 1 24 T4OUT T1OUT 2 23 R2IN T2OUT 3 22 R2OUT R1IN 4 21 T5IN R1OUT 5 20 T5OUT T2IN 6 MAX207E 6 T2IN 7 18 T3IN GND 8 17 R3OUT VCC 9 16 R3IN C1+ 10 15 V- V+ 11 14 C2- C1- 12 13 C2+ T2OUT 3 +5V 400kΩ TTL/CMOS INPUTS 18 T3IN T3 T3OUT 1 +5V RS-232 OUTPUTS 400kΩ 19 T4IN T1IN T2 19 T4IN T4 T4OUT 24 +5V 400kΩ DIP/SO/SSOP 21 T5IN 5 R1OUT T5 R1 T5OUT 20 R1IN 4 5kΩ TTL/CMOS OUTPUTS 22 R2OUT R2 R2IN 23 RS-232 INPUTS 5kΩ 17 R3OUT R3 R3IN 16 5kΩ GND 8 18 Maxim Integrated MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers ____________Pin Configurations and Typical Operating Circuits (continued) TOP VIEW +5V INPUT 0.1μF 6.3V 0.1μF 10 9 VCC C1+ 0.1μF 6.3V 12 C113 C2+ 0.1μF 16V 14 C2- V+ 11 +5V TO +10V VOLTAGE DOUBLER +10V TO -10V VOLTAGE INVERTER 0.1μF 16V V- 15 +5V 400kΩ 5 T1IN T2OUT 1 24 T3OUT T1OUT 2 23 R3IN R2IN 3 22 R3OUT R2OUT 4 21 T4IN T1IN 5 20 T4OUT R1OUT 6 19 T3IN R1IN 7 18 T2IN GND 8 17 R4OUT MAX208E VCC 9 16 R4IN C1+ 10 15 V- V+ 11 14 C2- C1- 12 13 C2+ Ω T1OUT 2 +5V 400kΩ 18 T2IN TTL/CMOS INPUTS T2 T2OUT 1 +5V RS-232 OUTPUTS 400kΩ 19 T3IN T3 T3OUT 24 +5V 400kΩ 21 T4IN 6 R1OUT T4 R1 T4OUT 20 R1IN 7 5kΩ 4 R2OUT DIP/SO/SSOP T1 R2 TTL/CMOS OUTPUTS R2IN 3 5kΩ 22 R3OUT R3 RS-232 INPUTS R3IN 23 5kΩ 17 R4OUT R4 R4IN 16 5kΩ GND 8 Maxim Integrated 19 MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers ____________Pin Configurations and Typical Operating Circuits (continued) +5V INPUT 0.1μF* 6.3V TOP VIEW 0.1μF 12 0.1μF* 6.3V 0.1μF* 16V 11 VCC C1+ V+ 13 +5V TO +10V VOLTAGE DOUBLER 14 C115 C2+ +10V TO -10V VOLTAGE INVERTER 16 C2- 0.1μF* 16V V- 17 +5V 400kΩ 7 T1IN T1 T1OUT 2 +5V 400kΩ T3OUT 1 28 T4OUT T1OUT 2 27 R3IN T2OUT 3 26 R3OUT R2IN 4 25 SHDN (SHDN) R2OUT 5 24 EN (EN) T2IN 6 MAX211E MAX213E MAX241E 6 T2IN TTL/CMOS INPUTS 7 R1OUT 8 R1IN 9 20 T3IN GND 10 19 R5OUT T2OUT 3 +5V RS-232 OUTPUTS 400kΩ 20 T3IN T3 T3OUT 1 +5V 400kΩ 23 R4IN T1IN T2 21 T4IN 22 R4OUT 21 T4IN 8 R1OUT T4 R1 T4OUT 28 R1IN 9 5kΩ VCC 11 18 R5IN C1+ 12 17 V- V+ 13 16 C2- C1- 14 15 C2+ 5 R2OUT R2 R2IN 4 5kΩ TTL/CMOS OUTPUTS 26 R3OUT R3 SO/SSOP R3IN 27 RS-232 INPUTS 5kΩ 22 R4OUT R4 R4IN 23 5kΩ 19 R5OUT R5IN 18 5kΩ ( ) ARE FOR MAX213E ONLY * 1.0μF CAPACITORS, MAX241E ONLY 24 EN (EN) 20 R5 SHDN (SHDN) GND 10 25 Maxim Integrated MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers Ordering Information (continued) PART MAX202ECUE TEMP RANGE 0°C to +70°C MAX202ECWE PART TEMP RANGE PIN-PACKAGE PIN-PACKAGE 16 TSSOP MAX208ECNG 0°C to +70°C 24 Narrow Plastic DIP 0°C to +70°C 16 Wide SO MAX208ECWG 0°C to +70°C 24 SO MAX202EC/D 0°C to +70°C Dice* MAX208ECAG 0°C to +70°C 24 SSOP MAX202EEPE -40°C to +85°C 16 Plastic DIP MAX208EENG -40°C to +85°C 24 Narrow Plastic DIP MAX202EESE -40°C to +85°C 16 Narrow SO MAX208EEWG -40°C to +85°C 24 SO MAX202EEUE -40°C to +85°C 16 TSSOP MAX208EEAG -40°C to +85°C 24 SSOP MAX202EEWE -40°C to +85°C 16 Wide SO MAX211ECWI 0°C to +70°C 28 SO MAX203ECPP 0°C to +70°C 20 Plastic DIP MAX211ECAI 0°C to +70°C 28 SSOP MAX203ECWP 0°C to +70°C 20 SO MAX211EEWI -40°C to +85°C 28 SO -40°C to +85°C 28 SSOP MAX203EEPP -40°C to +85°C 20 Plastic DIP MAX211EEAI MAX203EEWP -40°C to +85°C 20 SO MAX213ECWI 0°C to +70°C 28 SO MAX205ECPG 0°C to +70°C 24 Wide Plastic DIP MAX213ECAI 0°C to +70°C 28 SSOP MAX205EEPG -40°C to +85°C 24 Wide Plastic DIP MAX213EEWI -40°C to +85°C 28 SO -40°C to +85°C 28 SSOP MAX206ECNG 0°C to +70°C 24 Narrow Plastic DIP MAX213EEAI MAX206ECWG 0°C to +70°C 24 SO MAX232ECPE 0°C to +70°C 16 Plastic DIP MAX206ECAG 0°C to +70°C 24 SSOP MAX232ECSE 0°C to +70°C 16 Narrow SO MAX206EENG -40°C to +85°C 24 Narrow Plastic DIP MAX232ECWE 0°C to +70°C 16 Wide SO MAX206EEWG -40°C to +85°C 24 SO MAX232EC/D 0°C to +70°C Dice* MAX206EEAG -40°C to +85°C 24 SSOP MAX232EEPE -40°C to +85°C 16 Plastic DIP MAX207ECNG 0°C to +70°C 24 Narrow Plastic DIP MAX232EESE -40°C to +85°C 16 Narrow SO MAX207ECWG 0°C to +70°C 24 SO MAX232EEWE -40°C to +85°C 16 Wide SO MAX207ECAG 0°C to +70°C 24 SSOP MAX241ECWI 0°C to +70°C 28 SO MAX207EENG -40°C to +85°C 24 Narrow Plastic DIP MAX241ECAI 0°C to +70°C 28 SSOP MAX207EEWG -40°C to +85°C 24 SO MAX241EEWI -40°C to +85°C 28 SO MAX207EEAG -40°C to +85°C 24 SSOP MAX241EEAI -40°C to +85°C 28 SSOP *Dice are specified at TA = +25°C. Maxim Integrated 21 MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers __________________________________________________________Chip Topographies MAX202E/MAX232E MAX211E/MAX213E/MAX241E T1OUT T4OUT R3IN T2OUT T3OUT V+ C1+ V CC GND R3OUT C1C2+ SHDN (SHDN) R2IN C2- R2OUT T2IN T1OUT V- 0.117" (2.972mm) R1IN EN (EN) T1IN R1OUT R4IN R1IN R4OUT T4IN GND R2IN T2OUT R1OUT T3IN R5OUT T1IN R5IN T2IN R2OUT 0.080" (2.032mm) 0.174" (4.420mm) V CC C1- C1+ V+ C2+ C2V- 0.188" (4.775mm) ( ) ARE FOR MAX213E ONLY TRANSISTOR COUNT: 123 TRANSISTOR COUNT: 542 SUBSTRATE CONNECTED TO GND SUBSTRATE CONNECTED TO GND ___________________Chip Information MAX205E/MAX206E/MAX207E/MAX208E TRANSISTOR COUNT: 328 SUBSTRATE CONNECTED TO GND 22 Maxim Integrated MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers Package Information PDIPN.EPS (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) Maxim Integrated 23 MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers Package Information (continued) 2 SSOP.EPS (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) 1 INCHES E H MILLIMETERS DIM MIN MAX MIN MAX A 0.068 0.078 1.73 1.99 A1 0.002 0.008 0.05 0.21 B 0.010 0.015 0.25 0.38 C D 0.20 0.09 0.004 0.008 SEE VARIATIONS E 0.205 e 0.212 0.0256 BSC 5.20 MILLIMETERS INCHES D D D D D 5.38 MIN MAX MIN MAX 0.239 0.239 0.278 0.249 0.249 0.289 6.07 6.07 7.07 6.33 6.33 7.33 0.317 0.397 0.328 0.407 8.07 10.07 8.33 10.33 N 14L 16L 20L 24L 28L 0.65 BSC H 0.301 0.311 7.65 7.90 L 0.025 0∞ 0.037 8∞ 0.63 0∞ 0.95 8∞ N A C B e A1 L D NOTES: 1. D&E DO NOT INCLUDE MOLD FLASH. 2. MOLD FLASH OR PROTRUSIONS NOT TO EXCEED .15 MM (.006"). 3. CONTROLLING DIMENSION: MILLIMETERS. 4. MEETS JEDEC MO150. 5. LEADS TO BE COPLANAR WITHIN 0.10 MM. 24 TITLE: PACKAGE OUTLINE, SSOP, 5.3 MM APPROVAL DOCUMENT CONTROL NO. 21-0056 REV. C 1 1 Maxim Integrated MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers Package Information (continued) INCHES N E DIM A A1 B C e E H L H MAX MIN 0.093 0.104 0.004 0.012 0.014 0.019 0.009 0.013 0.050 0.291 0.299 0.394 0.419 0.050 0.016 SOICW.EPS (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) MILLIMETERS MIN 2.35 0.10 0.35 0.23 MAX 2.65 0.30 0.49 0.32 1.27 7.40 7.60 10.65 10.00 0.40 1.27 VARIATIONS: 1 INCHES TOP VIEW DIM D D D D D D A B e FRONT VIEW MIN 0.398 0.447 0.496 0.598 0.697 MAX 0.413 0.463 0.512 0.614 0.713 MILLIMETERS MIN 10.10 11.35 12.60 15.20 17.70 MAX 10.50 11.75 13.00 15.60 18.10 N MS013 16 AA 18 AB 20 AC 24 AD 28 AE C 0∞-8∞ A1 L SIDE VIEW TITLE: PACKAGE OUTLINE, .300" SOIC DOCUMENT CONTROL NO. 21-0042 REV. B 1 1 TSSOP4.40mm.EPS APPROVAL Maxim Integrated MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, +5V RS-232 Transceivers Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. 26 © Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 The Maxim logo and Maxim Integrated are trademarks of Maxim Integrated Products, Inc.