FUJITSU SEMICONDUCTOR DATA SHEET DS07-12512-8E 8-bit Proprietary Microcontroller CMOS F2MC-8L MB89190/190A Series MB89191/193/195/P195/PV190 MB89191A/191AH/193A/193AH/195A/P195A/PV190A ■ OUTLINE The MB89190/190A series microcontrollers contain various resources such as timers, serial interfaces, A/D converters, external interrupts, and remote-control functions, as well as an F2MC*-8L CPU core for low-voltage and high-speed operations. These single-chip microcontrollers are suitable for small devices such as remote controllers with compact packages. *: F2MC stands for FUJITSU Flexible Microcontroller. ■ FEATURES • Minimum execution time: 0.95 µs at 4.2 MHz (VCC = 2.7 V) • F2MC-8L family CPU core • Two timers 8/16-bit timer/counter 20-bit timebase counter • Serial interface 8-bit synchronous serial (Selectable transfer direction allows communication with various equipment.) (Continued) ■ PACKAGE 28-pin Plastic SOP 28-pin Plastic DIP 28-pin Plastic SH-DIP 48-pin Ceramic MQFP (FPT-28P-M17) (DIP-28P-M05) (DIP-28P-M03) (MQP-48C-P01) MB89190/190A Series (Continued) • External interrupts Edge detection (Selectable edge): 3 channels Low-level interrupt (Wake-up function): 8 channels • A/D converter (MB89190A series only) 8-bit successive approximation type: 8 channels • Built-in remote-control transmitting frequency generator • Low-power consumption modes Stop mode (Almost no current consumption occurs because oscillation stops.) Sleep mode (The current consumption is reduced about 1/3 of that during normal operation because the CPU stops.) • Packages SOP-28, SH-DIP-28, and DIP-28 ■ PRODUCT LINEUP Part number Item MB89191 MB89191A MB89191AH MB89193 MB89193A MB89193AH MB89195 MB89195A Classification Mask ROM products ROM size 4 K × 8 bits (internal mask ROM) RAM size 128 × 8 bits 16 K × 8 bits (internal mask ROM) MB89PV190 MB89PV190A One-time product For development and evaluation 16 K × 8 bits 32 K × 8 bits (internal PROM, (external ROM) to be programmed with generalpurpose EPROM programmer) 256 × 8 bits CPU functions The number of basic instructions: Instruction bit length: Instruction length: Data bit length: Minimum execution time: Interrupt processing time: Ports Output port (N channel open drain): 4 (also serves as peripherals for MB89190A series)or 6 (for MB89190 series) I/O port (CMOS): 16 (also serves as peripherals) Total: 20 or 22 Timer counter 2 8 K × 8 bits (internal mask ROM) MB89P195 MB89P195A 136 8 bits 1 to 3 bytes 1, 8, and 16 bits 0.95 µs at 4.2 MHz 8.57 µs at 4.2 MHz 2 channels of 8-bit timer counter or one 16-bit event counter (operation clock: 1.9 µs, 30.4 µs, and 487.6 µs at 4.2 MHz, and external clock) Serial I/O 8 bits LSB/MSB first selectable Transfer clock (external, 1.9 µs, 7.6 µs, 30.4 µs at 4.2 MHz) A/D converter (MB89190A series only) 8 bits x 8 channels A/D conversion mode (conversion time: 41.9 µs at 4.2 MHz) Sense mode (conversion time: 11.9 µs at 4.2 MHz) Capable of continuous activation by an internal timer. Reference voltage input (Continued) MB89190/190A Series (Continued) Part number Item External interrupt 1 MB89191 MB89191A MB89191AH MB89193 MB89193A MB89193AH MB89195 MB89195A MB89P195 MB89P195A MB89PV190 MB89PV190A 3 independent channels (selectable edge, interrupt vector, and interrupt source flag) Rising/falling/both edge selectable Used for wake-up from stop/sleep mode. (Edge detection is also permitted in the stop mode.) External interrupt 2 (Wake-up function) 8 channels (low-level interrupt only) Remote-control transmitting frequency generator The pulse width and cycle are software-programmable. Standby mode Sleep mode and stop mode Process CMOS Operating voltage* 2.2 V to 6.0 V 2.7 V to 6.0 V EPROM for use MBM27C256A20TVM *: Varies with conditions such as operating frequencies (see “■ Electrical Characteristics.”) It differs from the operating voltage of an A/D converter. ■ PACKAGE AND CORRESPONDING PRODUCTS MB89191 MB89191A MB89191AH MB89193 MB89193A MB89193AH MB89195 MB89195A Package MB89P195 MB89P195A × DIP-28P-M05 × DIP-28P-M03 : Available × × FPT-28P-M17 MQP-48C-P01 MB89PV190 MB89PV190A × × * × : Not available * : A socket (manufacturer: Sun Hayato Co., Ltd.) for pin pitch conversion is available. 48QF-28SOP-8L: (MQP-48C-P01) → for conversion to FPT-28P-M17 Inquiry: Sun Hayato Co., Ltd.: TEL (81)-3-3986-0403 FAX (81)-3-5396-9106 Note: For more information on each package, see “■ Package Dimensions.” 3 MB89190/190A Series ■ DIFFERENCES AMONG PRODUCTS 1. Memory Size Before evaluating using the piggyback model, verify its difference from the model that will actually be used. Take particular care on the following points: • On the MB89191/191A, addresses 0140H to 0180H cannot be used for register banks. • The stack area, etc., is set in the upper limit of the RAM. 2. Current Consumption • In the case of MB89PV190/PV190A, added is the current consumed by the EPROM which is connected to the top socket. • When operated at low speed, the products with an OTPROM (EPROM) will consume more current than the products with a mask ROM. However, the same is current consumption in the sleep/stop mode. (For more information, see “■ Electrical Characteristics.”) 3. Mask Options Functions that can be selected as options and how to designate these options vary with product. Before using options, check “■ Mask Options.” Take particular care on the following points: • Pull-up resistor optional cannot be set for P00 to P03, and P40 to P45 on the MB89191A/193A/195A/P195A. • The power-on reset option is fixed as “enabled” for MB89P195/P195A. • Options are fixed on the MB89PV190/PV190A. 4. MB89191AH/MB89193AH MB89191AH/193AH are “L” level heavy output current drive type of P30 to P32 and P40 to P43 of MB89191A/ 193A.Characteristics other than “L” level output of P30 to P32 and P40 to P43 are the same as MB89191A/193A. 4 MB89190/190A Series ■ PIN ASSIGNMENT (TOP VIEW) P04/INT24 1 28 VCC P05/INT25 2 27 P03/INT23/AN7 P06/INT26 3 26 P02/INT22/AN6 P07/INT27 4 25 P01/INT21/AN5 TEST 5 24 P00/INT20/AN4 RST 6 23 P45/AVR X0 7 22 P44/AVSS X1 8 21 P43/AN3 VSS 9 20 P42/AN2 P37/BZ/RCO 10 19 P41/AN1 P36/INT12 11 18 P40/AN0 P35/INT11 12 17 P30/SCK P34/TO/INT10 13 16 P31/SO P33/EC 14 15 P32/SI (FPT–28P–M17) (DIP–28P–M03) (DIP–28P–M05) 5 MB89190/190A Series P35/INT11 N. C. N. C. N. C. N. C. N. C. VSS N. C. N. C. N. C. N. C. N. C. 48 47 46 45 44 43 42 41 40 39 38 37 68 67 66 65 64 63 62 61 (Top view) P34/TO/INT10 1 P33/EC 2 P32/SI 3 69 P31/SO 4 70 P30/SCK 5 71 Each pin inside the dashed line is for MB89PV190/PV190A units only. 36 N. C. 35 N. C. 60 34 P36/INT12 59 33 P37/BZ/RCO 58 32 X1 57 31 X0 56 30 RST 74 55 29 TEST P43/AN3 9 75 54 28 P07/INT27 P44/AVSS 10 76 53 27 P06/INT26 P45/AVR 11 26 P05/INT25 P00/INT20/AN4 12 25 P04/INT24 13 14 15 16 17 18 19 20 21 22 23 24 P01/INT21/AN5 N. C. N. C. N. C. N. C. V CC N. C. N. C. N. C. N. C. P02/INT22/AN6 P03/INT23/AN7 52 8 51 P42/AN2 50 73 49 7 80 P41/AN1 79 72 78 6 77 P40/AN0 (MQP-48C-P01) • Pin assignment on the package top (MB89PV190/PV190A only) Pin no. Pin name Pin no. Pin name Pin no. Pin name Pin no. Pin name 49 VPP 57 N.C. 65 O4 73 OE 50 A12 58 A2 66 O5 74 N.C. 51 A7 59 A1 67 O6 75 A11 52 A6 60 A0 68 O7 76 A9 53 A5 61 O1 69 O8 77 A8 54 A4 62 O2 70 CE 78 A13 55 A3 63 O3 71 A10 79 A14 56 N.C. 64 VSS 72 N.C. 80 VCC N.C.: Internally connected. Do not use. 6 MB89190/190A Series ■ PIN DESCRIPTION Pin no. Pin name SOP*1, DIP*2 SH-DIP*3 MQFP*4 7 31 X0 8 32 X1 5 29 6 Circuit type Function A Clock oscillation pins TEST B Test input pin Connect directly to VSS. 30 RST C Reset I/O pin This pin consists of an N-ch open-drain output with a pull-up resistor and of hysteresis input. A low level is output from this pin by internal source. The internal circuit is initialized by the input of a low level. 24 to 27 12 13, 23, 24 P00/INT20/ AN4 to P03/ INT23/AN7 G General-purpose I/O ports Also serve as external interrupt input pins. In the MB89190A series, also serve as analog input pins. External interrupt input is of hysteresis input type. 1 to 4 25 to 28 P04/INT24 to P07/INT27 D General-purpose I/O ports Also serve as external interrupt input. External interrupt input is of hysteresis input type. 17 5 P30/SCK D General-purpose I/O port Also serves as clock I/O for the 8-bit serial I/O interface. The serial I/O clock input is of hysteresis input type with a built-in noise filter. 16 4 P31/SO E General-purpose I/O port Also serves as a serial I/O data output pin. 15 3 P32/SI D General-purpose I/O port Also serves as a serial I/O data input pin. The serial I/O data input is of hysteresis input type with a built-in noise filter. 14 2 P33/EC D General-purpose I/O port Also serves as an external clock input pin for the 8bit timer/counter. External clock input of the 8-bit timer/counter is hysteresis input type with a built-in noise filter. 13 1 P34/TO/ INT10 D General-purpose I/O port Also serves as the overflow output and external interrupt input for the 8-bit timer/counter. External interrupt input is of hysteresis input type with a built-in noise filter. *1: *2: *3: *4: FPT-28P-M17 DIP-28C-M05 DIP-28P-M03 MQP-48C-P01 (Continued) 7 MB89190/190A Series (Continued) Pin no. MQFP*4 12 48 P35/INT11 11 34 P35/INT12 10 33 18 to 21 6 to 9 23 *1: *2: *3: *4: 8 Pin name SOP*1, DIP*2 SH-DIP*3 Circuit type Function D General-purpose I/O port Also serve as external interrupt input pins. External interrupt input is of hysteresis input type with a built-in noise filter. P37/BZ/RCO E General-purpose I/O port Also serves as a buzzer output pin and remotecontrol output pin. P40/AN0 to P43/AN3 F N-ch open-drain output ports Also serve as analog input pins for the A/D converter. 11 P45/AVR F In the MB89190A series, also serves as a reference voltage input pin for the A/D converter. In the MB89190 series, serves as an N-ch opendrain output port. 22 10 P44/AVSS F In the MB89190A series, also serves as a power pin for the A/D converter, and should be applied the same voltage as VSS to. In the MB89190 series, also serves as an N-ch open-drain output port. 28 18 VCC — Power supply pin 9 42 VSS — Power supply (GND) pin FPT-28P-M17 DIP-28P-M05 DIP-28P-M03 MQP-48C-P01 MB89190/190A Series • External EPROM pins (MB89PV190/PV190A) Pin no. Pin name I/O Function 49 VPP O “H” level output pin 79 78 50 75 71 76 77 51 52 53 54 55 58 59 60 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 O Address output pins 61 62 63 65 66 67 68 69 O1 O2 O3 O4 O5 O6 O7 O8 I Data input pins 70 CE O ROM chip enable pin Outputs “H” during standby. 73 OE O ROM output enable pin Outputs “L” at all times. 80 VCC O EPROM power pin 64 VSS O Power supply (GND) pin 9 MB89190/190A Series ■ I/O CIRCUIT TYPE Type A Circuit Remarks • Oscillation feedback registor of approximately 1 MΩ at 5 V X1 X0 • When crystal and ceramic oscillators are selected optionally Standby control signal X1 X0 • When CR oscillation is selected optionally Standby control signal B C • Output pull-up resistor (P-ch): Approx. 50 kΩ at 5 V • Hysteresis input R P-ch N-ch D • CMOS output • CMOS input • Hysteresis input (resource input) R P-ch P-ch N-ch • Pull-up resistor optional (Continued) 10 MB89190/190A Series (Continued) Type Circuit Remarks E • CMOS output • CMOS input R P-ch P-ch N-ch • Pull-up resistor optional F • N-ch open-drain output • Analog input R Pch Nch Analog input G • Pull-up resistor optional (MB89190 series only) • • • • R P-ch CMOS output CMOS input Hysteresis input (resource input) Analog input P-ch N-ch Analog input • Pull-up resistor optional (MB89190 series only) 11 MB89190/190A Series ■ HANDLING DEVICES 1. Preventing Latch-up Latchup may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input or output pins other than medium- and high-voltage pins or if higher than the voltage which shows on “ 1. Absolute Maximum Ratings” in “■ Electrical Characteristics” is applied between VCC to VSS. When latchup occurs, power supply current increases rapidly and might thermally damage elements. When using, take great care not to exceed the absolute maximum ratings. Also, take care to prevent the analog power supply (AVCC and AVR) and analog input from exceeding the digital power supply (VCC) when the analog system power supply is turned on and off. 2. Treatment of Unused Input Pins Leaving unused input pins open could cause malfunctions. They should be connected to pull-up or pull-down resistor. 3. Treatment of Power Supply Pins on Microcontrollers with A/D and D/A Converters Connect to be AVCC=DAVC=VCC and AVSS=AVR=VSS even if the A/D and D/A converters are not in use. 4. Treatment of N.C. Pin Be sure to leave (internally connected) N.C. pins open. 5. Power Supply Voltage Fluctuations Although operation is assured within the rated range of VCC power supply voltage, a rapid fluctuation of the voltage could cause malfunctions within the rated range. Stabilizing voltage supplied to the IC is therefore important. As stabilization guidelines, it is recommended to control power so that VCC ripple fluctuations (P-P value) will be less than 10% of the standard VCC value at the commercial frequency (50 to 60 Hz) and the transient fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when power is switched. 6. Precautions when Using an External Clock Even when an external clock is used, oscillation stabilization time is required for power-on reset (optional) and release from stop mode. 12 MB89190/190A Series ■ PROGRAMMING TO PROM ON THE MB89P195/P195A The MB89P195/P195A can program data in the internal PROM using a dedicated conversion adaptor and specified general-purpose EPROM programmer. 1. Memory Space Address in normal operation mode EPROM mode (Corresponding addresses on the EPROM programmer) 0000 H I/O 0080 H RAM 0180 H 8000 H Not available 0000 H Vacancy (Read value FFH) C000 H 4000 H PROM 16 K FFFF H EPROM 16 K 7FFF H • Programming procedure (1) Load program data into the ROM programmer at addresses 4000H to 7FFFH. (Addresses 0C000H to 0FFFFH in the operation mode correspond to 4000H to 7FFFH in ROM programmer. See the illustration above.) (2) Set the data at addresses 0000H to 3FFFH of the programmer ROM in the ROM programmer, to FFH. (3) Program in the successive-address write mode of the ROM programmer. Note: Program must be started at the address 00000H. For details, contact our Sales Division. 13 MB89190/190A Series 2. Recommended Screening Conditions High-temperature aging is recommended as the pre-assembly screening procedure for a product with a blanked OTPROM microcontroller program. Program, verify Aging +150 °C for 48 h Data verification Assembly 3. Programming Yield Due to its nature, bit programming test can’t be conducted as Fujitsu delivery test. For this reason, a programming yield of 100% cannot be assured at all times. 4. EPROM Programmer Socket Adapter Recommended programmer manufacturer and programmer name Part no. MB89P195 MB89P195A MB89P195PF MB89P195APF Package Compatible socket adapter Sun Hayato Co., Ltd. Minato Electronics Inc. MODEL1890A (ver.2.2) + OU-910 (ver.4.1) Data I/O Co., Ltd. UNISITE (ver.5.0 or later) DIP-28 ROM-28DP28DP-8L Recommended Recommended SOP-28 ROM-28SOP28DP-8L Recommended Recommended Inquiry: Sun Hayato Co., Ltd.: TEL: (81)-3-3986-0403 FAX: (81)-3-5396-9106 Minato Electronics Inc.: TEL: USA (1)-916-348-6066 JAPAN (81)-45-591-5611 Data I/O Co., Ltd.: TEL: USA/ASIA (1)-206-881-6444 EUROPE (49)-8-985-8580 14 3900 (ver.2.8 or later) 2900 (ver.3.8 or later) MB89190/190A Series ■ PROGRAMMING TO THE EPROM WITH PIGGYBACK/EVALUATION DEVICE 1. EPROM for Use MBM27C256A-20TVM 2. Programming Socket Adapter To program to the EPROM using an EPROM programmer, use the socket adapter (manufacturer: Sun Hayato Co., Ltd.) below. Package Adapter socket part number LCC-32 ROM-32LC-28DP-YS Inquiry: Sun Hayato Co., Ltd.: TEL (81)-3-3986-0403 FAX (81)-3-5396-9106 3. Memory Space Address in normal operation mode Address when writing to EPROM (Corresponding addresses on the EPROM programmer) 0000 H I/O 0080 H RAM 0180 H Not available 8000 H 0000 H EPROM 32 K PROM 32 K FFFF H 7FFF H 4. Programming to the EPROM (1) Set the EPROM programmer for MBM27C256A. (2) Load program data into the EPROM programmer at 0000H to 7FFFH. (3) Program to 0000H to 7FFFH with the EPROM programmer. 15 MB89190/190A Series ■ BLOCK DIAGRAM X0 Oscillator (Max. 4.2 MHz) X1 Timebase timer Internal bus Clock control Reset circuit (WDT) RST 4 Port 0 CMOS I/O port 8-bit timer/counter P34/TO /INT10 8-bit timer/counter P33/EC External interrupt (Wake-up) P04/INT24 to P07/INT27 P00/INT20/AN4 to 4 P03/INT23/AN7 P30/SCK P45*/AVR P44*/AV SS Port 4 (MB89190A only) P40/AN0 to P43/AN3 P32/SI P31/SO Port 3 8-bit A/D converter 8-bit serial P35/INT11 External interrupt 4 P36/INT12 N-ch open-drain output port Remote-control transmit frequency generator P37/BZ/RCO Buzzer output RAM CMOS I/O port F2MC-8L CPU ROM The other pins TEST, VCC, V SS 16 *: In the MB89190A series, P44 and P45 serve only as AVR and AV ss pins, respectively, and cannot be used as ports. The MB89190 has no built-in A/D converter. MB89190/190A Series ■ CPU CORE 1. Memory Space The microcontrollers of MB89190/190A series offer a 64 Kbytes of memory for storing all of I/O, data, and program areas. The I/O area is allocated from the lowest address. The data area is allocated immediately above the I/O area. The data area can be divided into register, stack, and direct areas according to the application. The program area is allocated from exactly the opposite end of I/O area, that is, the highest address. The tables of interrupt reset vectors, and vector call instructions are allocated from the highest address within the program area. The memory space of the MB89190/190A series is structured below: Memory Space MB89191/191A 0000 H MB89193/193A 0000 H I/O 0080 H MB89195/195A MB89P195/P195A 0000 H I/O 0080 H MB89PV190/PV190A 0000 H I/O 0080 H I/O 0080 H Vacancy 00C0 H 0100 H RAM RAM 0100 H Register RAM 0100 H Register RAM 0100 H Register Register 0140 H 0180 H 0180 H 0180 H Not available Not available Not available Not available 8000 H C000 H External ROM Program PROM (Mask ROM) E000 H F000 H Mask ROM Mask ROM FFFF H FFFF H FFFF H FFFF H 17 MB89190/190A Series 2. Registers The F2MC-8L family has two types of registers; dedicated hardware registers and general-purpose memory registers. The following dedicated registers are provided: Program counter (PC): A 16-bit-long register for indicating the instruction storage positions Accumulator (A): A 16-bit-long temporary register for arithmetic operations, etc. When the instruction is an 8-bit data processing instruction, the lower byte is used. Temporary accumulator (T): A 16-bit-long register which is used for arithmetic operations with the accumulator. When the instruction is an 8-bit data processing instruction, the lower byte is used. Index register (IX): A 16-bit-long register for index modification Extra pointer (EP) : A 16-bit-long pointer for indicating a memory address Stack pointer (SP) : A 16-bit-long pointer for indicating a stack area Program status (PS) : A 16-bit-long register for storing a register pointer, a condition code Initial value 16 bits FFFDH : Program counter PC A : Accumulator T : Temporary accumulator Indeterminate IX : Index register Indeterminate EP : Extra pointer Indeterminate SP : Stack pointer Indeterminate PS : Program status Indeterminate I-flag = 0, IL1, 0 = 11 The other bit values are indeterminate The PS can further be divided into higher 8 bits for use as a register bank pointer (RP) and the lower 8 bits for use as a condition code register (CCR) (see the diagram below). Structure of the Program Status Register 15 PS 14 13 12 RP 10 9 8 Vacancy Vacancy Vacancy RP 18 11 7 6 H I 5 4 IL1, 0 3 2 1 0 N Z V C CCR MB89190/190A Series The RP indicates the address of the register bank currently in use. The relationship between the pointer contents and the actual address is based on the conversion rule illustrated below. Rule for Conversion of Actual Addresses of the General-purpose Register Area RP Lower OP codes “0” “0” “0” “0” “0” “0” “0” “1” R4 R3 R2 R1 R0 b2 ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ b1 b0 ↓ ↓ Generated addresses A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 The CCR consists of bits indicating the results of arithmetic operations and the contents of transfer data, and bits for control of CPU operations at the time of an interrupt. H-flag: Set to ‘1’ when a carry or a borrow from bit 3 to bit 4 occurs as a result of an arithmetic operation. Cleared to ‘0’ otherwise. This flag is for decimal adjustment instructions. I-flag: Interrupt is enabled when this flag is set to ‘1’. Interrupt is disabled when the flag is cleared to ‘0’. Cleared to ‘0’ at the reset. IL1, 0: Indicates the level of the interrupt currently allowed. Processes an interrupt only if its request level is higher than the value indicated by this bit. IL1 IL0 Interrupt level 0 0 0 1 1 0 2 1 1 3 1 High-low High Low N-flag: Set to ‘1’ if the MSB becomes ‘1’ as the result of an arithmetic operation. Cleared to ‘0’ otherwise. Z-flag: Set to ‘1’ when an arithmetic operation results in 0. Cleared to ‘0’ otherwise. V-flag: Set to ‘1’ if the complement on ‘2’ overflows as a result of an arithmetic operation. Cleared to ‘0’ if the overflow does not occur. C-flag: Set to ‘1’ when a carry or a borrow from bit 7 occurs as a result of an arithmetic operation. Cleared to ‘0’ otherwise. Set to ‘1’ the shift-out value in the case of a shift instruction. 19 MB89190/190A Series The following general-purpose registers are provided: General-purpose registers: An 8-bit-long register for storing data The general-purpose registers are of 8 bits and located in register banks of the memory. One bank contains eight registers and up to a total of 16 banks can be used on the MB89190/190A (8 banks on MB89191/191A). The bank currently in use is indicated by the register bank pointer. (RP) Note: The number of register banks that can be used varies with the RAM size. Register Bank Configuraiton This address = 0100 H + 8 × (RP) R0 R1 R2 R3 R4 R5 R6 R7 16 banks (8 banks for the MB89191/191A) Memory area 20 MB89190/190A Series ■ I/O MAP Address Read/write Register name 00H (R/W) PDR0 Port 0 data register 01H (W) DDR0 Port 0 data direction register 02H (R/W) ENI0 Port 0 input enable register 03H to 07H Register description Vacancy 08H (R/W) STBC Standby control register 09H (R/W) WDTC Watchdog control register 0AH (R/W) TBTC Time-base timer control register 0BH 0CH Vacancy (R/W) PDR3 Port 3 data register 0DH (W) DDR3 Port 3 data direction register 0EH (R/W) PDR4 Port 4 data register 0FH (R/W) BUZR Buzzer register 10H to 13H Vacancy 14H (R/W) RCR1 Remote-control transmit control register 1 15H (R/W) RCR2 Remote-control transmit control register 2 16H Vacancy 17H Vacancy 18H (R/W) T2CR Timer 2 control register 19H (R/W) T1CR Timer 1 control register 1AH (R/W) T2DR Timer 2 data register 1BH (R/W) T1DR Timer 1 data register 1CH (R/W) SMR Serial mode register 1DH (R/W) SDR Serial data register 1EH Vacancy 1FH Vacancy 20H (R/W) ADC1 A/D converter control register 1 21H (R/W) ADC2 A/D converter control register 2 22H (R/W) ADCD A/D converter data register 23H (R/W) EIC1 24H (R/W) EIC2 25H to 31H External interrupt control register 1 External interrupt control register 2 Vacancy 32H (R/W) EIE2 External interrupt 2 enable register 33H (R/W) EIF2 External interrupt 2 flag register 7CH (W) ILR1 Interrupt level register 1 7DH (W) ILR2 Interrupt level register 2 7EH (W) ILR3 Interrupt level register 3 34H to 7BH 7FH Vacancy Vacancy Note: Do not use vacancies. 21 MB89190/190A Series ■ ELECTRICAL CHARACTERISTICS 1. Absolute Maximum Rating (AVSS = VSS = 0.0 V) Parameter Symbol Value Unit Remarks Min. Max. VCC VSS – 0.3 VSS + 7.0 V AVR VSS – 0.3 VSS + 7.0 V Must not exceed VCC + 0.3 V. MB89190A series only EPROM program voltage VPP VSS – 0.3 VSS + 13.0 V MB89P195/P195A only Input voltage VI VSS – 0.3 VCC + 0.3 V Output voltage VO VSS – 0.3 VCC + 0.3 V IOL1 10 mA Except P33 and P34 (Except P30 toP34 and P40 to P43 for MB89191AH/193AH) IOL2 20 mA P33, P34(P30 toP34 and P40 to P43 for MB89191AH/193AH) mA Except P33 and P34 (Except P30 toP34 and P40 to P43 for MB89191AH/193AH) Average value (operating current × operation rate) Power supply voltage “L” level maximum output current IOLAV1 4 “L” level average output current IOLAV2 8 mA P33 and P34(P30 toP34 and P40 to P43 for MB89191AH/193AH) Average value (operating current × operation rate) “L” level total average output current ΣIOLAV 20 mA Average value (operating current × operation rate) “L” level total maximum output current ΣIOL 100 mA “H” level maximum output current IOH1 –10 mA Except P33, P34, and P37 IOH2 –20 mA P33, P34, P37 IOHAV1 –2 mA Except P33, P34, and P37 Average value (operating current × operation rate) IOHAV2 –4 mA Except P33, P34, and P37 Average value (operating current × operation rate) “H” level total average output current ΣIOHAV –10 mA Average value (operating current × operation rate) “H” level total maximum output current ΣIOH –30 mA Power consumption PD 200 mW Operating temperature Ta –40 +85 °C Storage temperature Tstg –55 +150 °C “H” level average output current WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. 22 MB89190/190A Series 2. Recommended Operating Conditions (VSS = 0.0 V) Symbol Parameter Power supply voltage VCC Value Unit Remarks 6.0* V Normal operation assurance range* MB89191/191A/193/193A/195/195A 2.7* 6.0* V Normal operation assurance range* MB89P195/P195A/PV190/PV190A 1.5 6.0 V Retains the RAM state in the stop mode Min. Max. 2.2* A/D converter reference input voltage AVR 0.0 VCC V Operating temperature TA –40 +85 °C *: These values vary with the operation frequency and the assured analog operation range. See Figure 1 and “ 5. A/D Converter Electrical Characteristics.” Operating voltage (V) 6 Analog accuracy assured in the Vcc = 3.5 V to 6.0 V range. 5 Operation assurance range 4 3 2 1 1 2 3 4 Main clock operation frequency (at an instruction cycle of 4/Fc) (MHz) 4.0 2.0 0.95 (µs) Minimum execution time (instruction cycle) (µs) Note: The shaded area is assured only for the MB89191/191A/193/193A/195/195A. Figure 1 Operating Voltage vs. Main Clock Operating Frequency Figure 1 indicates the operating frequency of the external oscillator at an instruction cycle of 4/FC. 23 MB89190/190A Series WARNING: Recommended operating conditions are normal operating ranges for the semiconductor device. All the device’s electrical characteristics are warranted when operated within these ranges. Always use semiconductor devices within the recommended operating conditions. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representative beforehand. 3. DC Characteristics Parameter Symbol VIH P00 to P07, P30 to P37, TEST 0.7 VCC VCC + 0.3 V VIHS RST, INT10 to INT12, EC, SCK, SI, INT20 to INT27 0.8 VCC VCC + 0.3 V VIL P00 to P03, P33 to P36, TEST VSS − 0.3 0.3 VCC V VILS RST, INT10 to INT12, EC, SCK, SI, INT 20 to INT27 VSS − 0.3 0.2 VCC V VD P40 to P44 VSS − 0.3 VSS + 0.3 V VOH1 P00 to P07, P30 to P32, P35, P36 IOH = –2.0 mA 2.4 V VOH2 P33, P34 IOH = –15 mA 2.4 V VOH3 P37 IOH = –7.0 mA 2.4 V VOL1 P00 to P07, P40 to P45, P30 to P32, P35 to P37 “H” level input voltage “L” level input voltage Open-drain output pin applied voltage “H” level output voltage “L” level output voltage Pin (VCC = +5.0 V, AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Value Condition Unit Remarks Min. Typ. Max. IOL = 1.8 mA 0.4 V P00 to P07, P35 to P37 VOL2 RST MB89191AH/ 193AH IOL = 4.0 mA 0.4 V P33, P34 IOL = 12 mA VOL3 0.4 V P30 to P34, P40 to P43 Input leakage current(Hi-z output leakage current) Except MB89191AH/ 193AH Except MB89191AH/ 193AH MB89191AH/ 193AH ILI1 P00 to P07, P30 to P37, TEST 0.0 V < VI < VCC ±5 µA Without pull-up resistor Open-drain output leakage current (Off ILD1 state) P40 to P45 0.0 V < VI < VCC ±1 µA Without pull-up resistor (Continued) 24 MB89190/190A Series (Continued) Parameter Pull-up resistance Symbol RPULL Pin P00 to P07, P30 to P37, P40 to P45, RST ICC Power supply voltage* (VCC = 5.0 V, AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Value Condition Unit Remarks Min. Typ. Max. VI = 0.0 V 25 50 100 kΩ — 5 10 MB89191/ 191A/193/ mA 193A/195/ 195A/PV190/ PV190A — 7 12 mA FC = 4.2 MHz VCC MB89P195/ P195A ICCS FC = 4.2 MHz — 3 7 mA Sleep mode ICCH TA = +25 °C — — 1 µA ICCA FC = 4.2 MHz During A/D converter operation — 6 13 MB89191A/ mA 193A/195A/ PV190A — 8 15 mA MB89P195A — 10 — pF Input capacitance CIN Except AVR, f = 1 MHz AVSS, VCC, and VSS Stop mode *: For the MB89PV190/PV190A, the current consumption of a connected EPROM and ICE is not included. The mesurement condition of the power supply current are set as VCC = 5.0 V with an external clock. 25 MB89190/190A Series 4. AC Characteristics (1) Reset Timing (VCC = +5.0 V±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Value Condition Unit Remarks Min. Max. Symbol Parameter RST “L” pulse width tZLZH — 16 tXCYL — ns Note: tXCYL is the oscillation period (1/FC) input to the X0 pin. t ZLZH RST 0.2 VCC 0.2 VCC (2) Power-on Reset (AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Parameter Symbol Power supply rising time tR Power supply cut-off time tOFF Condition — Value Unit Min. Max. — 50 ms 1 — ms Remarks Due to repeated operations Note: Make sure that power supply rises within the oscillation stabilization time selected. If power supply voltage needs to be varied in the course of operation, a smooth voltage rise is recommended. t OFF tR 2.0 V VCC 26 0.2 V 0.2 V 0.2 V MB89190/190A Series (3) Clock Timings Symbol Parameter Pin Condition (AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Value Unit Remarks Min. Max. Clock frequency FC X0, X1 — 1 4.2 MHz Clock cycle time tXCYL X0, X1 — 238 1000 ns Input clock pulse width PWH PWL X0 — 20 — ns External clock Input clock pulse risilng/falling time tCR tCF X0 — — 10 ns External clock X0, X1 Timings and Conditions of Applied Voltage t XCYL PWH PWL t CF t CR 0.8 VCC 0.8 VCC X0 0.2 VCC 0.2 VCC 0.2 VCC Clock Conditions When a crystal or ceramic resonator is used X0 When an external clock is used X1 X0 X1 Open (4) Instruction Cycles (AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Parameter Instruction cycle (minimum execution time) Symbol tinst Value (typical) Unit Remarks 4/FC µs tinst = 0.95 µs when operating at FC = 4.2 MHz 27 MB89190/190A Series (5) Recommended Resonator Manufacturers • Sample Application of Piezoelectric Resonator (FAR Series) X0 X1 R C1*2 FAR*1 C2*2 *1: Fujitsu Acoustic Resonator FAR part number (built-in capacitor type) FAR-C4SA-04000- 01M Inquiry: FUJITSU LIMITED 28 Frequency Dumping (MHz) resistor 4.00 200 Ω Initial deviation of FAR frequency (TA = +25°C) Temperature characteristics of FAR frequency (TA = –20°C to +60°C) Loading capacitors*2 ±0.5% ±0.5% Built-in MB89190/190A Series • Sample Application of Ceramic Resonator X0 X1 R C1 * C2 • Mask ROM products Resonator manufacturer* Murata Mfg. Co., Ltd. TDK. Co., Ltd. Resonator Frequency (MHz) CSA2.00MG040 CST2.00MG040 CSA4.00MG CST4.00MGW CSTCS4.00MG0C5 CCR4.0MC3 FCR4.0MC5 4.00 Resonator Frequency (MHz) 2.00 4.00 C1 (pF) C2 (pF) R 100 Built-in 30 Built-in Built-in Built-in Built-in 100 Built-in 30 Built-in Built-in Built-in Built-in Not required Not required Not required Not required Not required Not required Not required C1 (pF) C2 (pF) R 30 Built-in 100 Built-in 30 Built-in 30 Built-in 100 Built-in 30 Built-in 1 kΩ 1 kΩ Not required Not required Not required Not required • One-time products Resonator manufacturer* Murata Mfg. Co., Ltd. Inquiry: CSA3.20MGCA CST3.20MGA CSA3.20MGA040 CST3.20MGWA040 CSA3.58MGCA CST3.58MGWHA 3.20 3.58 Murata Mfg. Co., Ltd •Murata Electronics North America. Inc.: TEL 1-404-436-1300 •Murata Europe Mnagement GmbH: TEL 49-911-66870 •Murata Electronics Singapore (Pte.) Ltd.: TEL 65-758-4233 TDK Corporation •TDK Corporation of America Chicago Regional Office: TEL 1-708-803-6100 •TDK Electronics Europe GmbH Components Division: TEL 49-2102-9450 •TDK Singapore (PTE) Ltd.: TEL 65-273-5022 •TDK Hongkong Co., Ltd.: TEL 852-736-2238 •Korea Branch, TDK Corporation: TEL 82-2-554-6633 29 MB89190/190A Series (6) Serial I/O Timings (VCC = 5.0 V±10%, AVSS = VSS= 0.0 V, TA = –40°C to +85°C) Parameter Symbol Pin Serial clock cycle time tSCYC SCK SCK ↓ → SO time tSLOV SCK, SO Valid SI → SCK ↑ tIVSH SI, SCK SCK ↑ → valid SI hold time tSHIX SCK, SI Serial clock “H” pulse width tSHSL Serial clock “L” pulse width tSLSH SCK ↓ → SO time tSLOV SCK, SO Valid SI → SCK ↑ tIVSH SI, SCK SCK ↑ → valid SI hold time tSHIX SCK, SI Condition Internal clock operation SCK External clock operation Value Max. 2 tinst* — µs –200 200 ns 1/2 tinst* — µs 1/2 tinst* — µs 1 tinst* — µs 1 tinst* — µs 0 200 ns 1/2 tinst* — µs 1/2 tinst* — µs *: For information on tinst, see “(4) Instruction Cycles.” Internal Shift Clock Mode t SCYC SCK 2.4 V 0.8 V 0.8 V t SLOV 2.4 V SO 0.8 V SI t IVSH t SHIX 0.8 VCC 0.8 VCC 0.2 VCC 0.2 VCC External Shift Clock Mode t SLSH SCK SO t SHSL 0.8 VCC 0.2 VCC 0.2 VCC t SLOV 2.4 V 0.8 V t SI 30 IVSH t SHIX 0.8 VCC 0.8 VCC 0.2 VCC 0.2 VCC Unit Min. 0.8 VCC Remarks MB89190/190A Series (7) Peripheral Input Timings (VCC = 5.0 V±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Value Pin Unit Remarks Min. Max. Symbol Parameter Peripheral input “H” pulse width 1 tILIH1 Peripheral input “L” pulse width 1 tIHIL1 EC, INT10 to INT12, INT20 to INT27 2 tinst* — µs 2 tinst* — µs *: For information on tinst, see “(4) Instruction Cycles.” Peripheral Input Timing Diagram t IHIL t ILIH EC INT10 to INT12 INT20 to INT27 0.8 VCC 0.2 VCC 0.8 VCC 0.2 VCC (VCC = 5.0 V±10%, AVSS= VSS = 0.0 V, TA = –40°C to +85°C) Parameter Symbol Value Pin Min. Typ. Max. Unit Peripheral input “H” noise limit width tIHNC EC, SI, SCK INT10 to INT12 7 15 23 ns Peripheral input “L” noise limit width tILNC EC, SI, SCK INT10 to INT12 7 15 23 ns Remarks Peripheral Input Timing Diagram t ILNC EC, SCK, S1 INT10 to INT12 t IHNC 0.8 VCC 0.2 VCC 0.8 VCC 0.2 VCC 31 MB89190/190A Series 5. A/D Converter Electrical Characteristics (MB89190A Series Only) (AVCC = VCC = 3.5 V to 6.0 V, AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Parameter Symbol Pin Resolution Condition — Total error — Linearity error Differential linearity error Zero transition voltage VOT AVR = AVCC — Full-scale transition voltage VFST Inter channel disparity A/D mode conversion time — Sense mode conversion time Analog port input current Unit Min. Typ. Max. — — 8 bit — — ±1.5 LSB — — ±1.0 LSB — — ±0.9 LSB AVSS +2.0 LSB mV AVR mV AVSS –1.0 LSB AVSS +0.5 LSB AVR –3.0 LSB AVR –1.5 LSB — — 0.5 LSB — 44 tinst* — µs — 12 tinst* — µs — — 10 µA 0 — AVR V 0 — VCC V — 100 300 µA — — 1 µA Remarks — IAIN Analog input voltage AN0 to AN7 — Reference voltage IR Reference voltage supply current Value AVR IRH AVR = VCC = 5.0 V when A/ D conversion is operating *: For information on tinst, see “(4) Instruction Cycles” in “4. AC Characteristics.” 6. A/D Converter Glossary • Resolution Analog changes that are identifiable by the A/D converter. When the number of bits is 8, analog voltage can be divided into 28=256. Linearity error (unit: LSB) The deviation of the straight line connecting the zero transition point (“0000 0000” ↔ “0000 0001”) with the full-scale transition point (“1111 1110” ↔ “1111 1111”) from actual conversion characteristics. Differential linearity error (unit: LSB) The deviation of input voltage needed change the output code by 1 LSB from the theoretical value. • Total error (unit: LSB) The difference between theoretical and actual conversion values. 32 MB89190/190A Series Digital output 1111 1111 • • • • • • • • • • • • • • • • • • • • 0000 0000 0000 Theoretical conversion value 1111 1110 Actual conversion value (1LSB × N + VOT) 1LSB = AVR 256 Linearity error VNT – (1LSB × N + VOT) 1LSB = Linearity error Differential linearity error = V( N + 1 ) T – VNT –1 1LSB = Total error VNT – (1LSB × N + 1LSB) 1LSB 0010 0001 0000 VOT VNT V( N + I )T VFST Analog input 7. Notes on Using A/D Converter • Input impedance of analog input pins The A/D converter used for the MB89190A series contains a sample hold circuit as illustrated below to fetch analog input voltage into the sample hold capacitor for eight instruction cycles after starting A/D conversion. For this reason, if the output impedance of the external circuit for the analog input is high, analog input voltage might not stabilize within the analog input sampling period. Therefore, it is recommended to keep the output impedance of the external circuit low (below 10 kΩ). Note that if the impedance cannot be kept low, it is recommended to connect an external capacitor of approx. 0.1 µF for the analog input pin. Analog input equivalent circuit Sample hold circuit, . C =. 33 pF Analog input pin Comparator If the analog input impedance is higher than 10 kΩ, it is recommended to connect an external capacitor of approx. 0.1 µF. . R =. 6 kΩ Close for 8 instruction cycles after starting A/D conversion. Analog channel selector • Error The smaller the AVR-AVSS, the greater the error would become relatively. 33 MB89190/190A Series ■ EXAMPLE CHARACTERISTICS (1) “L” Level Output Voltage VOL1 vs. IOL VCC = 2.5 V VCC = 3.0 V VCC = 2.0 V VOL (V) 0.30 VOL (V) 0.6 VCC = 4.0 V TA = +25°C 0.25 VCC = 5.0 V VCC = 6.0 V 0.20 0.2 0.05 0.1 2 3 4 5 IOL (mA) VOL3 vs. IOL VOL (V) 1.2 VCC = 2.0 V VCC = 2.5 V TA = +25°C 1.0 0.8 VCC = 3.0 V 0.6 VCC = 4.0 V VCC = 5.0 V VCC = 6.0 V 0.4 0.2 0.0 34 0.4 0.10 1 0 2 4 6 8 10 12 14 16 18 20 IOL (mA) VCC = 5.0 V VCC = 6.0 V 0.5 0.3 0 VCC = 4.0 V TA = +25°C 0.15 0.00 VOL2 vs. IOL VCC = 2.5 V VCC = 3.0 V VCC = 2.0 V 0.0 0 1 2 3 4 5 6 7 8 9 10 IOL (mA) MB89190/190A Series (2) “H” Level Output Voltage VOH1 vs. IOH VCC = 4.0 V VCC = 2.5 V VCC = 2.0 V VCC = 3.0 V VCC - VOH (V) 0.6 TA = +25°C 0.5 VOH2 vs. IOH VCC = 5.0 V VCC = 6.0 V VCC - VOH (V) VCC = 3.0 V 3.0 TA = +25°C VCC = 2.5 V 2.5 0.4 2.0 0.3 1.5 0.2 1.0 0.1 0.5 0.0 0 –1 –2 –3 –4 –5 IOH (mA) 0.0 VCC = 2.0 V VCC = 4.0 V VCC = 5.0 V VCC = 6.0 V 0 –4 –8 – 12 – 16 – 20 IOH (mA) VOH3 vs. IOH VCC - VOH (V) VCC = 2.0 V 1.2 TA = + 25°C VCC = 2.5 V VCC = 3.0 V 1.0 0.8 VCC = 4.0 V 0.6 VCC = 5.0 V VCC = 6.0 V 0.4 0.2 0.0 0 –2 –4 –6 –8 – 10 IOH (mA) (3) “H” Level Input Voltage/“L” Level Input Voltage (CMOS Input) (4) “H” Level Input Voltage/“L” Level Input Voltage (Hysteresis Input) VIN vs. VCC VIN (V) 5.0 4.5 TA = +25°C 4.0 TA= +25°C 3.5 VIHS 3.0 4.0 2.5 3.5 VILS 2.0 3.0 1.5 2.5 1.0 2.0 0.5 1.5 0.0 1.0 0 0.5 0.0 VIN vs. VCC VIN (V) 5.0 4.5 0 1 2 3 4 5 6 7 VCC (V) 1 2 3 4 5 6 7 VCC (V) VIHS: Threshold when input voltage in hysteresis characteristics is set to “H” level VILS: Threshold when input voltage in hysteresis characteristics is set to “L” level 35 MB89190/190A Series (5) Power Supply Current (External Clock) ICC vs. VCC ICC (mA) 6 ICCS vs. VCC ICCS (mA) 1.50 TA = +25°C TA = +25°C 5 Fc = 4.2 MHz 1.25 Fc = 4.2 MHz 4 1.00 Fc = 3.0 MHz 3 Fc = 3.0 MHz 0.75 2 0.50 Fc = 1.0 MHz 1 Fc = 1.0 MHz 0.25 0 0.00 1 2 3 4 5 6 7 2 1 3 4 5 6 7 VCC (V) 5 6 7 AVR (V) VCC (V) ICCH vs. VCC ICCH (µA) 2.0 IR vs. AVR IR (µA) 150 TA = +25°C 1.8 TA = +25°C 1.6 125 1.4 100 1.2 1.0 75 0.8 50 0.6 0.4 25 0.2 0 0 1 2 3 4 5 6 7 1 2 3 VCC (V) (6) Pull-up Resistance RPULL vs. VCC RPULL (kΩ) 1000 TA = +25°C 100 10 36 1 2 3 4 5 6 VCC (V) 4 MB89190/190A Series ■ MASK OPTION LIST Part number No. MB89191 MB89191A MB89193 MB89193A MB89195 MB89195A when Specifying procedure Specify ordering masking 1 2 P00 to P07 Selectable by pin Port pull-up P30 to P37 resistors P00 to P03 Selectable Not P40 to P45 by pin available Power-on reset • Power-on reset provided • No power-on reset • 218/FC (approx. 62.4 ms) • 216/FC (approx. 15.6 ms) • 212/FC (approx. 0.98 ms) • 22/FC (approx. 0 ms) MB89P195A –101*2 Specify when ordering masking None Selectable by pin None –201*2 MB89PV190 MB89PV190A Fixed None Not available Selectable Not None by pin available Not available Selectable Provided Provided Provided Selectable Fixed to 216/FC Selectable Fixed to 216/FC Provided Provided Selection of oscillation stabilization wait time (at 4.2 MHz)*1 3 MB89P195 4 Reset pin output • Reset output provided • No reset output Selectable Provided Selectable 5 Oscillation type of clock 1 Crystal and ceramic oscillators 2 CR Selectable “1” only Selectable “1” only Provided Fixed to 216/FC “1” only *1: The oscillation stabilization time is generated by dividing the original clock oscillation. The time described in this item should be used as a rough guideline since the oscillation cycle is unstable immediately after oscillation starts. “FC” indicates the original oscillation frequency. *2: –101 and –201 are provided respectively for the MB89P195 and MB89P195A OTP versions as the standard products. 37 MB89190/190A Series ■ ORDERING INFORMATION Part number MB89191PF MB89193PF MB89195PF MB89P195PF-101PF MB89191APF MB89191AHPF MB89193APF MB89193AHPF MB89195APF MB89P195APF-201PF MB89191P-SH MB89193P-SH MB89195P-SH MB89191AP-SH MB89191AHP-SH MB89193AP-SH MB89193AHP-SH MB89195AP-SH MB89191P MB89193P MB89195P MB89P195P-101P MB89191AP MB89191AHP MB89193AP MB89193AHP MB89195AP MB89P195AP-201P MB89PV190CF MB89PV190ACF 38 Package 28-pin Plastic SOP (FPT-28P-M17) 28-pin Plastic SH-DIP (DIP-28C-M03) 28-pin Plastic DIP (DIP-28P-M05) 48-pin Ceramic MQFP (MQP-48C-P01) Remarks MB89190/190A Series ■ PACKAGE DIMENSION 28-pin Plastic SOP (FPT-28P-M17) +0.25 17.75 –0.20 28 15 +.010 .699 –.008 Details of "B" part Details of "A" part 0.15(.006) 0.35(.014) 11.80±0.30 (.465±.012) INDEX 8.60±0.20 (.339±.008) 0.20(.008) 0.20(.008) "A" 0.18(.007) MAX 0.68(.027) MAX 1 0.18(.007) MAX 0.68(.027) MAX 14 1.27(.050) TYP 0.45±0.10 (.018±.004) 0.13(.005) M 2.80(.110)MAX (Mounting height) 0.15±0.05 (.006±.002) "B" 0.10(.004) 16.51(.650) REF C 0.80±0.20 (.031±.008) 10.20±0.30 (.402±.012) Dimensions in mm (inches) 1994 FUJITSU LIMITED F28048S-1C-1 28-pin Plastic DIP (DIP-28P-M05) 0(0)MIN (STAND OFF) +0.20 35.73 –0.30 +.008 1.407 –.012 INDEX-1 13.80±0.25 (.543±.010) INDEX-2 +0.50 +0.50 0.99 –0 .039 1.52 –0 +.020 –0 +.020 .060 –0 0.51(.020)MIN 4.96(.195)MAX 0.25±0.05 (.010±.002) 3.00(.118)MIN 1.58(.062) MAX C 1994 FUJITSU LIMITED D28013S-3C-2 2.54(.100) TYP 0.46±0.08 (.018±.003) 15.24(.600) TYP 15°MAX Dimensions in mm (inches) 39 MB89190/190A Series 28-pin Plastic SH-DIP (DIP-28P-M03) +0.20 26.00 –0.30 1.024 +.008 –.012 INDEX-1 9.10±0.25 (.358±.010) INDEX-2 4.85(.191)MAX 0.51(.020)MIN 0.25±0.05 (.010±.002) 3.00(.118)MIN 0.45±0.10 (.018±.004) +0.50 1.00 –0 10.16(.400) TYP +.020 .039 –0 1.778±0.18 (.070±.007) 23.114(.910)REF 1.778(.070) MAX C 15° Dimensions in mm (inche 1994 FUJITSU LIMITED D28012S-3C-3 48-pin Ceramic MQFP (MQP-48C-P01) 17.20(.677)TYP PIN No.1 INDEX 15.00±0.25 (.591±.010) 14.82±0.35 (.583±.014) 1.50(.059)TYP 8.80(.346)REF 1.00(.040)TYP 0.80±0.22 (.0315±.0087) PIN No.1 INDEX 1.02±0.13 (.040±.005) +0.13 10.92 –0.0 +.005 .430 –0 7.14(.281) 8.71(.343) TYP TYP PAD No.1 INDEX 0.30(.012)TYP +0.45 4.50(.177)TYP 1.10 –0.25 +.018 .043 –.010 0.40±0.08 (.016±.003) 0.60(.024)TYP 8.50(.335)MAX 0.15±0.05 (.006±.002) C 40 1994 FUJITSU LIMITED M48001SC-4-2 Dimensions in mm (inches) MB89190/190A Series FUJITSU LIMITED All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information and circuit diagrams in this document are presented as examples of semiconductor device applications, and are not intended to be incorporated in devices for actual use. Also, FUJITSU is unable to assume responsibility for infringement of any patent rights or other rights of third parties arising from the use of this information or circuit diagrams. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that Fujitsu will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan. F0112 FUJITSU LIMITED Printed in Japan