MC34164, MC33164, NCV33164 Micropower Undervoltage Sensing Circuits The MC34164 series are undervoltage sensing circuits specifically designed for use as reset controllers in portable microprocessor based systems where extended battery life is required. These devices offer the designer an economical solution for low voltage detection with a single external resistor. The MC34164 series features a bandgap reference, a comparator with precise thresholds and built−in hysteresis to prevent erratic reset operation, an open collector reset output capable of sinking in excess of 6.0 mA, and guaranteed operation down to 1.0 V input with extremely low standby current. The MC devices are packaged in 3−pin TO−226AA, micro size TSOP−5, 8−pin SOIC−8 and Micro8™ surface mount packages. The NCV device is packaged in SOIC−8. Applications include direct monitoring of the 3.0 V or 5.0 V MPU/logic power supply used in appliance, automotive, consumer, and industrial equipment. • Temperature Compensated Reference • Monitors 3.0 V (MC34164−3) or 5.0 V (MC34164−5) Power Supplies • Precise Comparator Thresholds Guaranteed Over Temperature • Comparator Hysteresis Prevents Erratic Reset • Reset Output Capable of Sinking in Excess of 6.0 mA • Internal Clamp Diode for Discharging Delay Capacitor • Guaranteed Reset Operation With 1.0 V Input • Extremely Low Standby Current: As Low as 9.0 A • Economical TO−226AA, TSOP−5, SOIC−8 and Micro8 Surface Mount Packages • NCV Prefix for Automotive and Other Applications Requiring Site and Control Changes • Pb−Free Packages are Available http://onsemi.com 8 1 1 2 3 TO−226AA P SUFFIX CASE 29 5 8 1 1 PIN CONNECTIONS Reset 1 8 N.C. Input 2 7 N.C. N.C. 3 6 N.C. Ground 4 5 N.C. (Top View) Pin 1. 2. 3. 4. 5. Reset TSOP−5 SN SUFFIX CASE 483 Micro8 DM SUFFIX CASE 846A TSOP−5 Input SOIC−8 D SUFFIX CASE 751 Ground Input Reset NC NC TO−226AA Pin 1. Reset 2. Input 3. Ground ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet. 1.2 Vref = Sink Only Positive True Logic DEVICE MARKING INFORMATION See general marking information in the device marking section on page 9 of this data sheet. GND Figure 1. Representative Block Diagram This device contains 28 active transistors. © Semiconductor Components Industries, LLC, 2005 August, 2005 − Rev. 16 1 Publication Order Number: MC34164/D MC34164, MC33164, NCV33164 MAXIMUM RATINGS Symbol Value Unit Power Input Supply Voltage Rating Vin −1.0 to 12 V Reset Output Voltage VO −1.0 to 12 V Reset Output Sink Current ISink Internally Limited mA IF 100 mA PD RJA 700 178 mW °C/W PD RJA 700 178 mW °C/W PD RJA 520 240 mW °C/W Operating Junction Temperature TJ +150 °C Operating Ambient Temperature Range MC34164 Series MC33164 Series, NCV33164 TA Storage Temperature Range Tstg Clamp Diode Forward Current, Reset to Input Pin (Note 1) Power Dissipation and Thermal Characteristics P Suffix, Plastic Package Maximum Power Dissipation @ TA = 25°C Thermal Resistance, Junction−to−Air D Suffix, Plastic Package Maximum Power Dissipation @ TA = 25°C Thermal Resistance, Junction−to−Air DM Suffix, Plastic Package Maximum Power Dissipation @ TA = 25°C Thermal Resistance, Junction−to−Air °C 0 to +70 − 40 to +125 Electrostatic Discharge Sensitivity (ESD) Human Body Model (HBM) Machine Model (MM) °C − 65 to +150 ESD V 4000 200 Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. MC34164−3, MC33164−3 SERIES, NCV33164−3 ELECTRICAL CHARACTERISTICS (For typical values TA = 25°C, for min/max values TA is the operating ambient temperature range that applies [Notes 2 & 3], unless otherwise noted.) Characteristic Symbol Min Typ Max Unit VIH VIL VH 2.55 2.55 0.03 2.71 2.65 0.06 2.80 2.80 − − − 0.14 0.1 0.4 0.3 6.0 12 30 − − 0.02 0.02 0.5 1.0 VF 0.6 0.9 1.2 V Operating Input Voltage Range Vin 1.0 to 10 − − V Quiescent Input Current Vin = 3.0 V Vin = 6.0 V Iin − − 9.0 24 15 40 COMPARATOR Threshold Voltage High State Output (Vin Increasing) Low State Output (Vin Decreasing) Hysteresis (ISink = 100 A) V RESET OUTPUT Output Sink Saturation (Vin = 2.4 V, ISink = 1.0 mA) (Vin = 1.0 V, ISink = 0.25 mA) VOL Output Sink Current (Vin, Reset = 2.4 V) ISink V Output Off−State Leakage (Vin, Reset = 3.0 V) (Vin, Reset = 10 V) Clamp Diode Forward Voltage, Reset to Input Pin (IF = 5.0 mA) mA A IR(leak) TOTAL DEVICE A 1. Maximum package power dissipation limits must be observed. 2. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient as possible. 3. Tlow = 0°C for MC34164 Thigh = +70°C for MC34164 = − 40°C for MC33164, NCV33164 = +125°C for MC33164, NCV33164 http://onsemi.com 2 MC34164, MC33164, NCV33164 MC34164−5, MC33164−5 SERIES, NCV33164−5 ELECTRICAL CHARACTERISTICS (For typical values TA = 25°C, for min/max values TA is the operating ambient temperature range that applies [Notes 5 & 6], unless otherwise noted.) Characteristic Symbol Min Typ Max Unit VIH VIL VH 4.15 4.15 0.02 4.33 4.27 0.09 4.45 4.45 − − − 0.14 0.1 0.4 0.3 7.0 20 50 − − 0.02 0.02 0.5 2.0 VF 0.6 0.9 1.2 V Operating Input Voltage Range Vin 1.0 to 10 − − V Quiescent Input Current Vin = 5.0 V Vin = 10 V Iin − − 12 32 20 50 COMPARATOR V Threshold Voltage High State Output (Vin Increasing) Low State Output (Vin Decreasing) Hysteresis (ISink = 100 A) RESET OUTPUT Output Sink Saturation (Vin = 4.0 V, ISink = 1.0 mA) (Vin = 1.0 V, ISink = 0.25 mA) VOL Output Sink Current (Vin, Reset = 4.0 V) V ISink mA A IR(leak) Output Off−State Leakage (Vin, Reset = 5.0 V) (Vin, Reset = 10 V) Clamp Diode Forward Voltage, Reset to Input Pin (IF = 5.0 mA) TOTAL DEVICE A 4. Maximum package power dissipation limits must be observed. 5. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient as possible. 6. Tlow = 0°C for MC34164 Thigh = +70°C for MC34164 = − 40°C for MC33164, NCV33164 = +125°C for MC33164, NCV33164 7. NCV prefix is for automotive and other applications requiring site and change control. 10 RL = 82 k to Vin TA = 25°C 8.0 VO , OUTPUT VOLTAGE (V) VO , OUTPUT VOLTAGE (V) 10 6.0 4.0 2.0 0 RL = 82 k to Vin TA = 25°C 8.0 6.0 4.0 2.0 0 0 2.0 4.0 6.0 Vin, INPUT VOLTAGE (V) 8.0 0 10 Figure 2. MC3X164−3 Reset Output Voltage versus Input Voltage 2.0 4.0 6.0 Vin, INPUT VOLTAGE (V) 8.0 Figure 3. MC3X164−5 Reset Output Voltage versus Input Voltage http://onsemi.com 3 10 5.0 5.0 4.0 4.0 V O , OUTPUT VOLTAGE (V) V O , OUTPUT VOLTAGE (V) MC34164, MC33164, NCV33164 3.0 2.0 1.0 3.0 2.0 1.0 RL = 82 k to Vin TA = 25°C RL = 82 k to Vin TA = 25°C 0 2.62 2.66 2.70 2.74 0 4.22 2.78 4.26 Vin, INPUT VOLTAGE (V) Figure 4. MC3X164−3 Reset Output Voltage versus Input Voltage Upper Threshold High State Output V in , THRESHOLD VOLTAGE (V) V in , THRESHOLD VOLTAGE (V) 4.38 4.36 2.72 2.68 2.64 Lower Threshold Low State Output 2.60 −50 −25 0 25 50 75 100 Upper Threshold High State Output 4.32 4.28 4.24 Lower Threshold Low State Output 4.20 −50 125 −25 0 25 50 75 100 125 TA, AMBIENT TEMPERATURE (°C) TA, AMBIENT TEMPERATURE (°C) Figure 6. MC3X164−3 Comparator Threshold Voltage versus Temperature Figure 7. MC3X164−5 Comparator Threshold Voltage versus Temperature 50 50 TA = 25°C 40 I in, INPUT CURRENT (μ A) I in, INPUT CURRENT (μ A) 4.34 Figure 5. MC3X164−5 Reset Output Voltage versus Input Voltage 2.76 30 TA = 0°C 20 TA = 70°C 10 0 4.30 Vin, INPUT VOLTAGE (V) 0 2.0 4.0 6.0 8.0 40 20 TA = 0°C TA = 70°C 10 0 10 TA = 25°C 30 0 2.0 4.0 6.0 8.0 Vin, INPUT VOLTAGE (V) Vin, INPUT VOLTAGE (V) Figure 8. MC3X164−3 Input Current versus Input Voltage Figure 9. MC3X164−5 Input Current versus Input Voltage http://onsemi.com 4 10 MC34164, MC33164, NCV33164 4.0 Vin = 2.4 V 3.0 V OL, OUTPUT SATURATION (V) V OL, OUTPUT SATURATION (V) 4.0 TA = 70°C TA = 25°C 2.0 TA = 0°C TA = 25°C TA = 0°C 1.0 TA = 70°C 0 TA = 25°C Vin, Reset = 4 V TA = 70°C TA = 0°C 3.0 TA = 25°C 2.0 TA = 0°C 1.0 TA = 70°C 0 0 4.0 8.0 12 16 20 4.0 0 8.0 12 16 VSink, SINK CURRENT (mA) ISink, SINK CURRENT (mA) Figure 10. MC3X164−3 Reset Output Saturation versus Sink Current Figure 11. MC3X164−5 Reset Output Saturation versus Sink Current I F , FORWARD CURRENT (mA) 32 Vin = 5.0 V to 4.0 V RL = 43 k TA = 25°C Reset Vin = 0 V TA = 25°C 24 90% Vin 5.0 V 16 4.0 V Vin 8.0 10 % 43k 5.0V 4.0V Reset Ref 0 0 0.4 0.8 1.2 5.0 s/DIV 1.6 VF , FORWARD VOLTAGE (V) Figure 12. Clamp Diode Forward Current versus Voltage Figure 13. Reset Delay Time (MC3X164−5 Shown) R Input Power Supply Reset Microprocessor Circuit Reset CDLY 1.2 Vref tDLY = RCDLY In ǒ 1− GND 1 Vth(MPU) Vin A time delayed reset can be accomplished with the addition of CDLY. For systems with extremely fast power supply rise times (<500 ns) it is recommended that the RCDLY time constant be greater than 5.0 s. Vth(MPU) is the microprocessor reset input threshold. Figure 14. Low Voltage Microprocessor Reset http://onsemi.com 5 Ǔ 20 MC34164, MC33164, NCV33164 Test Data RH Iin Vin RL Power Supply Microprocessor Circuit Reset 1.2 Vref MC3X164−5 VH ≈ 4.3 RH RL + 0.06 Vth(lower) ≈ 10 RH x 10−6 GND where: RH ≤ 1.0 k 43 k ≥ RL ≥ 4.3 k VH (mV) Vth (mV) RH () RL (k) 60 103 123 160 155 199 280 262 306 357 421 530 0 1.0 1.0 1.0 2.2 2.2 2.2 4.7 4.7 4.7 4.7 4.7 0 100 100 100 220 220 220 470 470 470 470 470 43 10 6.8 4.3 10 6.8 4.3 10 8.2 6.8 5.6 4.3 Comparator hysteresis can be increased with the addition of resistor RH. The hysteresis equation has been simplified and does not account for the change of input current Iin as Vin crosses the comparator threshold (Figure 8). An increase of the lower threshold Vth(lower) will be observed due to Iin which is typically 10 A at 4.3 V. The equations are accurate to ±10% with RH less than 1.0 k and RL between 4.3 k and 43 k. Figure 15. Low Voltage Microprocessor Reset With Additional Hysteresis (MC3X164−5 Shown) Input 1.0 k Input Power Supply Reset Reset Solar Cells 1.2 Vref 1.2 Vref GND GND Figure 16. Voltage Monitor Figure 17. Solar Powered Battery Charger VCC RL MTP3055EL 270 4.3V Input Reset Overheating of the logic level power MOSFET due to insufficient gate voltage can be prevented with the above circuit. When the input signal is below the 4.3 V threshold of the MC3X164−5, its output grounds the gate of the L2 MOSFET. 1.2 Vref GND MC3X164−5 Figure 18. MOSFET Low Voltage Gate Drive Protection Using the MC3X164−5 http://onsemi.com 6 MC34164, MC33164, NCV33164 ORDERING INFORMATION Device Package MC33164D−3 Shipping † SOIC−8 MC33164D−3G SOIC−8 (Pb−Free) MC33164D−3R2 SOIC−8 MC33164D−3R2G SOIC−8 (Pb−Free) NCV33164D−3R2* SOIC−8 NCV33164D−3R2G* 98 Units / Rail 2500 Units / Tape & Reel SOIC−8 (Pb−Free) MC33164DM−3R2 Micro8 MC33164DM−3R2G Micro8 (Pb−Free) MC33164P−3 4000 Units / Tape & Reel TO−92 MC33164P−3G TO−92 (Pb−Free) MC33164P−3RA 2000 Units / Box TO−92 MC33164P−3RAG TO−92 (Pb−Free) MC33164P−3RP 2000 Units / Tape & Reel TO−92 MC33164P−3RPG TO−92 (Pb−Free) MC33164D−5 2000 Units / Pack SOIC−8 MC33164D−5G SOIC−8 (Pb−Free) MC33164D−5R2 SOIC−8 MC33164D−5R2G SOIC−8 (Pb−Free) NCV33164D−5R2* SOIC−8 NCV33164D−5R2G* 98 Units / Rail 2500 Units / Tape & Reel SOIC−8 (Pb−Free) MC33164DM−5R2 Micro8 MC33164DM−5R2G Micro8 (Pb−Free) MC33164P−5 4000 Units / Tape & Reel TO−92 MC33164P−5G TO−92 (Pb−Free) MC33164P−5RA 2000 Units / Box TO−92 MC33164P−5RAG TO−92 (Pb−Free) MC33164P−5RP 2000 Units / Tape & Reel TO−92 MC33164P−5RPG TO−92 (Pb−Free) MC34164D−3 2000 Units / Pack SOIC−8 MC34164D−3G SOIC−8 (Pb−Free) MC34164D−3R2 SOIC−8 MC34164D−3R2G SOIC−8 (Pb−Free) http://onsemi.com 7 98 Units / Rail 2500 Units / Tape & Reel MC34164, MC33164, NCV33164 ORDERING INFORMATION Device Package MC34164DM−3R2 Shipping † Micro8 MC34164DM−3R2G MC34164P−3 MC34164P−3G MC34164P−3RP MC34164P−3RPG MC34164D−5 Micro8 (Pb−Free) 4000 Units / Tape & Reel TO−92 2000 Units / Box TO−92 (Pb−Free) 2000 Units / Box TO−92 2000 Units / Pack TO−92 (Pb−Free) 2000 Units / Pack SOIC−8 MC34164D−5G SOIC−8 (Pb−Free) 98 Units / Rail MC34164D−5R2 SOIC−8 2500 Units / Tape & Reel MC34164D−5R2G SOIC−8 (Pb−Free) 2500 Units / Tape & Reel MC34164DM−5R2 Micro8 4000 Units / Tape & Reel Micro8 (Pb−Free) 4000 Units / Tape & Reel MC34164DM−5R2G MC34164SN−5T1 TSOP−5 MC34164SN−5T1G MC34164P−5 MC34164P−5G MC34164P−5RA TSOP−5 (Pb−Free) 3000 Units / Tape & Reel TO−92 2000 Units / Box TO−92 (Pb−Free) 2000 Units / Box TO−92 MC34164P−5RAG MC34164P−5RP MC34164P−5RPG TO−92 (Pb−Free) 2000 Units / Tape & Reel TO−92 2000 Units / Pack TO−92 (Pb−Free) 2000 Units / Pack *NCV33164: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 8 MC34164, MC33164, NCV33164 PIN CONNECTIONS AND MARKING DIAGRAMS SOIC−8 D SUFFIX CASE 751 TSOP−5 SN SUFFIX CASE 483 5 4 8 2 3 Micro8 MC34164DM CASE 846A 8 MIy0 YWW AWL 3x164 ALYWy G SRCYWG 1 Micro8 MC33164DM CASE 846A 8 MCy0 YWW AWL TO−92 MC3x164P−yRA MC3x164P−yRP MC3x164P−y CASE 29 MC3x1 64P−y YWW 1 1 SRC x y A WL, L YY, Y WW, W G 1 = Device Code = Device Number 3 or 4 = Suffix Number 3 or 5 = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free http://onsemi.com 9 123 MC34164, MC33164, NCV33164 PACKAGE DIMENSIONS TO−226AA P SUFFIX CASE 29−11 ISSUE AL A NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. CONTOUR OF PACKAGE BEYOND DIMENSION R IS UNCONTROLLED. 4. LEAD DIMENSION IS UNCONTROLLED IN P AND BEYOND DIMENSION K MINIMUM. B R P L SEATING PLANE K DIM A B C D G H J K L N P R V D X X G J H V C SECTION X−X 1 N N http://onsemi.com 10 INCHES MIN MAX 0.175 0.205 0.170 0.210 0.125 0.165 0.016 0.021 0.045 0.055 0.095 0.105 0.015 0.020 0.500 −−− 0.250 −−− 0.080 0.105 −−− 0.100 0.115 −−− 0.135 −−− MILLIMETERS MIN MAX 4.45 5.20 4.32 5.33 3.18 4.19 0.407 0.533 1.15 1.39 2.42 2.66 0.39 0.50 12.70 −−− 6.35 −−− 2.04 2.66 −−− 2.54 2.93 −−− 3.43 −−− MC34164, MC33164, NCV33164 PACKAGE DIMENSIONS TSOP−5 SN SUFFIX PLASTIC PACKAGE CASE 483−02 ISSUE D NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. A AND B DIMENSIONS DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. D 5 S 4 1 2 B 3 L G A DIM A B C D G H J K L M S J C 0.05 (0.002) H M K MILLIMETERS MIN MAX 2.90 3.10 1.30 1.70 0.90 1.10 0.25 0.50 0.85 1.05 0.013 0.100 0.10 0.26 0.20 0.60 1.25 1.55 0_ 10 _ 2.50 3.00 SOLDERING FOOTPRINT* 0.95 0.037 1.9 0.074 2.4 0.094 1.0 0.039 0.7 0.028 SCALE 10:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 11 INCHES MIN MAX 0.1142 0.1220 0.0512 0.0669 0.0354 0.0433 0.0098 0.0197 0.0335 0.0413 0.0005 0.0040 0.0040 0.0102 0.0079 0.0236 0.0493 0.0610 0_ 10 _ 0.0985 0.1181 MC34164, MC33164, NCV33164 PACKAGE DIMENSIONS SOIC−8 D SUFFIX CASE 751−07 ISSUE AG NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07. −X− A 8 5 S B 1 0.25 (0.010) M Y M 4 K −Y− G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE −Z− 0.10 (0.004) H D 0.25 (0.010) M Z Y S X M J S SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 12 MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8 _ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 MC34164, MC33164, NCV33164 PACKAGE DIMENSIONS Micro8 DM SUFFIX CASE 846A−02 ISSUE F NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. 846A−01 OBSOLETE, NEW STANDARD 846A−02. −A− −B− K PIN 1 ID G D 8 PL 0.08 (0.003) M T B S A DIM A B C D G H J K L S SEATING −T− PLANE 0.038 (0.0015) C L J H SOLDERING FOOTPRINT* 8X 1.04 0.041 0.38 0.015 3.20 0.126 6X 8X 4.24 0.167 0.65 0.0256 5.28 0.208 SCALE 8:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 13 MILLIMETERS MIN MAX 2.90 3.10 2.90 3.10 −−− 1.10 0.25 0.40 0.65 BSC 0.05 0.15 0.13 0.23 4.75 5.05 0.40 0.70 INCHES MIN MAX 0.114 0.122 0.114 0.122 −−− 0.043 0.010 0.016 0.026 BSC 0.002 0.006 0.005 0.009 0.187 0.199 0.016 0.028 MC34164, MC33164, NCV33164 Micro8 is a trademark of International Rectifier. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: N. American Technical Support: 800−282−9855 Toll Free Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Phone: 81−3−5773−3850 Email: [email protected] http://onsemi.com 14 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. MC34164/D