MOTOROLA MC68HC05BD3 Hcmos microcontroller Datasheet

Freescale Semiconductor, Inc.
MC68HC05BD3D/H
TECHNICAL DATA
Freescale Semiconductor, Inc...
MC68HC05BD3
HC05
MC68HC05BD3
MC68HC705BD3
MC68HC05BD5
TECHNICAL
DATA
!MOTOROLA
!MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
GENERAL DESCRIPTION
1
PIN DESCRIPTION AND I/O PORTS
2
MEMORY AND REGISTERS
3
RESETS AND INTERRUPTS
4
MULTI-FUNCTION TIMER
5
PULSE WIDTH MODULATION
6
M-BUS SERIAL INTERFACE
7
SYNC SIGNAL PROCESSOR
8
CPU CORE AND INSTRUCTION SET
9
LOW POWER MODES
10
OPERATING MODES
11
ELECTRICAL SPECIFICATIONS
12
MECHANICAL SPECIFICATIONS
13
MC68HC705BD3
14
TPG
MC68HC05BD5
For More Information On This Product,
Go to: www.freescale.com
15
1
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
1
GENERAL DESCRIPTION
2
PIN DESCRIPTION AND I/O PORTS
3
MEMORY AND REGISTERS
4
RESETS AND INTERRUPTS
5
MULTI-FUNCTION TIMER
6
PULSE WIDTH MODULATION
7
M-BUS SERIAL INTERFACE
8
SYNC SIGNAL PROCESSOR
9
CPU CORE AND INSTRUCTION SET
10
LOW POWER MODES
11
OPERATING MODES
12
ELECTRICAL SPECIFICATIONS
13
MECHANICAL SPECIFICATIONS
14
MC68HC705BD3
15
MC68HC05BD5
For More Information On This Product,
Go to: www.freescale.com
TPG
2
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
MC68HC05BD3
MC68HC705BD3
MC68HC05BD5
High-density complementary
metal oxide semiconductor
(HCMOS) microcontroller unit
All Trade Marks recognized. This document contains information on new products. Specifications and information herein are
subject to change without notice.
All products are sold on Motorola’s Terms & Conditions of Supply. In ordering a product covered by this document the
Customer agrees to be bound by those Terms & Conditions and nothing contained in this document constitutes or forms part
of a contract (with the exception of the contents of this Notice). A copy of Motorola’s Terms & Conditions of Supply is available
on request.
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty,
representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any
liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including
without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All
operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts.
Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed,
intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a
situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended
or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly
or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and !are registered
trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
The Customer should ensure that it has the most up to date version of the document by contacting its local Motorola office.
This document supersedes any earlier documentation relating to the products referred to herein. The information contained
in this document is current at the date of publication. It may subsequently be updated, revised or withdrawn.
 MOTOROLA LTD., 1996
TPG
For More Information On This Product,
Go to: www.freescale.com
3
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Conventions
Register and bit mnemonics are defined in the paragraphs describing them.
An overbar is used to designate an active-low signal, eg: RESET.
Unless otherwise stated, blank cells in a register diagram indicate that the bit is
either unused or reserved; shaded cells indicate that the bit is not described in the
following paragraphs; ‘u’ is used to indicate an undefined state (on reset).
TPG
For More Information On This Product,
Go to: www.freescale.com
4
Freescale Semiconductor, Inc.
CUSTOMER FEEDBACK QUESTIONNAIRE (MC68HC05BD3D/H)
Motorola wishes to continue to improve the quality of its documentation. We would welcome your feedback on the publication you
have just received. Having used the document, please complete this card (or a photocopy of it, if you prefer).
1.
How would you rate the quality of the document? Check one box in each category.
Excellent
Organization
Readability
Understandability
Accuracy
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
Excellent
❏
❏
❏
❏
❏
Tables
Table of contents
Index
Page size/binding
Overall impression
Poor
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
Comments:
2.
What is your intended use for this document? If more than one option applies, please rank them (1, 2, 3).
❏
❏
❏
Selection of device for new application
System design
Training purposes
3.
❏
Please specify:
How well does this manual enable you to perform the task(s) outlined in question 2?
Completely
– Cut along this line to remove –
Other
Not at all
Comments:
❏ ❏ ❏ ❏
4.
How easy is it to find the information you are looking for?
Easy
Difficult
Comments:
❏ ❏ ❏ ❏
5.
Is the level of technical detail in the following sections sufficient to allow you to understand how the device functions?
Too little detail
SECTION 1
GENERAL DESCRIPTION
SECTION 2
PIN DESCRIPTION AND I/O PORTS
SECTION 3
MEMORY AND REGISTERS
SECTION 4
RESETS AND INTERRUPTS
SECTION 5
MULTI-FUNCTION TIMER
SECTION 6
PULSE WIDTH MODULATION
SECTION 7
M-BUS SERIAL INTERFACE
SECTION 8
SYNC SIGNAL PROCESSOR
SECTION 9
CPU CORE AND INSTRUCTION SET
SECTION 10
LOW POWER MODES
SECTION 11
OPERATING MODES
SECTION 12
ELECTRICAL SPECIFICATIONS
SECTION 13
MECHANICAL SPECIFICATIONS
SECTION 14
MC68HC705BD3
SECTION 15
MC68HC05BD5
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
Too much detail
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
Comments:
6.
Have you found any errors? If so, please comment:
7.
From your point of view, is anything missing from the document? If so, please say what:
TPG
✂
Freescale Semiconductor, Inc...
Illustrations
❏
❏
❏
❏
❏
Poor
For More Information On This Product,
Go to: www.freescale.com
5
Freescale Semiconductor, Inc.
✂
8.
How could we improve this document?
9.
How would you rate Motorola’s documentation?
Excellent
– In general
– Against other semiconductor suppliers
Poor
❏ ❏
❏ ❏
❏❏
❏❏
10. Which semiconductor manufacturer provides the best technical documentation?
11. Which company (in any field) provides the best technical documentation?
Less than 1 year
❏
1–3 years
❏
3–5 years
❏
More than 5 years
❏
– Second fold back along this line –
By air mail
Par avion
Motorola Semiconductors H.K. Ltd.,
13/F, Prosperity Centre,
77-81 Container Port Road,
Kwai Chung, N.T.,
HONG KONG.
– Cut along this line to remove –
FIX STAMP HERE
– First fold back along this line –
Freescale Semiconductor, Inc...
12. How many years have you worked with microprocessors?
F.A.O. HKG CSIC Technical Publications
(re: MC68HC05BD3D/H)
!MOTOROLA
Semiconductor Products Sector
Asia Pacific Group
FAX: (852) 2485-0548
– Third fold back along this line –
13. Currently there is some discussion in the semiconductor industry regarding a move towards providing data sheets in electronic
form. If you have any opinion on this subject, please comment.
14. We would be grateful if you would supply the following information (at your discretion), or attach your card.
Name:
Position:
Phone No:
FAX No:
Department:
Company:
Address:
Thank you for helping us improve our documentation,
HKG CSIC Technical Publications , Motorola Semiconductors H.K. Ltd., Hong Kong.
TPG
– Finally, tuck this edge into opposite flap –
For More Information On This Product,
Go to: www.freescale.com
6
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
TABLE OF CONTENTS
Paragraph
Number
TITLE
Page
Number
1
GENERAL DESCRIPTION
1.1
Features.................................................................................................................1-1
2
PIN DESCRIPTION AND I/O PORTS
2.1
PIN DESCRIPTIONS.............................................................................................2-1
2.2
Pin Assignments ....................................................................................................2-2
2.3
INPUT/OUTPUT PORTS.......................................................................................2-3
2.3.1
Port A ...............................................................................................................2-3
2.3.2
Port B ...............................................................................................................2-3
2.3.3
Port C ...............................................................................................................2-4
2.3.4
Port D ...............................................................................................................2-4
2.3.5
Input/Output Programming...............................................................................2-4
2.3.6
Port C and D Configuration Registers..............................................................2-5
3
MEMORY AND REGISTERS
3.1
3.2
3.3
3.4
3.5
3.6
3.7
Registers ...............................................................................................................3-1
RAM (MC68HC05BD3)..........................................................................................3-1
RAM (MC68HC705BD3/MC68HC05BD5).............................................................3-1
ROM (MC68HC05BD3) .........................................................................................3-2
ROM (MC68HC05BD5) .........................................................................................3-2
EPROM (MC68HC705BD3) ..................................................................................3-2
Bootstrap ROM ......................................................................................................3-2
TPG
MC68HC05BD3
MOTOROLA
i
For More Information On This Product,
Go to: www.freescale.com
7
Freescale Semiconductor, Inc.
Paragraph
Number
TITLE
Page
Number
Freescale Semiconductor, Inc...
4
RESETS AND INTERRUPTS
4.1
RESETS ................................................................................................................4-1
4.1.1
Power-On Reset (POR) ...................................................................................4-1
4.1.2
RESET Pin.......................................................................................................4-1
4.1.3
Illegal Address (ILADR) Reset.........................................................................4-2
4.1.4
Computer Operating Properly (COP) Reset ....................................................4-2
4.2
INTERRUPTS........................................................................................................4-3
4.2.1
Non-maskable Software Interrupt (SWI) ..........................................................4-3
4.2.2
Maskable Hardware Interrupts.........................................................................4-5
4.2.2.1
External Interrupt (IRQ)..............................................................................4-5
4.2.2.2
Sync Signal Processor Interrupt.................................................................4-7
4.2.2.3
M-Bus Interrupts.........................................................................................4-7
4.2.2.4
Multi-Function Timer Interrupts ..................................................................4-8
5
MULTI-FUNCTION TIMER
5.1
5.2
5.3
MFT Counter Register ...........................................................................................5-1
MFT Control and Status Register ..........................................................................5-1
COP Watchdog......................................................................................................5-2
6
PULSE WIDTH MODULATION
6.1
6.2
PWM Registers .....................................................................................................6-1
General Operation .................................................................................................6-1
7
M-BUS SERIAL INTERFACE
7.1
M-Bus Interface Features ......................................................................................7-1
7.2
M-Bus Protocol ......................................................................................................7-2
7.2.1
START Signal...................................................................................................7-3
7.2.2
Slave Address Transmission ............................................................................7-3
7.2.3
Data Transfer....................................................................................................7-4
7.2.4
Repeated START Signal ..................................................................................7-4
7.2.5
STOP Signal ....................................................................................................7-4
7.2.6
Arbitration Procedure .......................................................................................7-4
7.2.7
Clock Synchronization .....................................................................................7-5
7.2.8
Handshaking....................................................................................................7-5
7.3
M-Bus Registers ....................................................................................................7-5
TPG
MOTOROLA
ii
MC68HC05BD3
For More Information On This Product,
Go to: www.freescale.com
8
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Paragraph
Number
TITLE
Page
Number
7.3.1
M-Bus Address Register (MADR) ....................................................................7-6
7.3.2
M-Bus Frequency Register (MFDR).................................................................7-6
7.3.3
M-Bus Control Register (MCR) ........................................................................7-7
7.3.4
M-Bus Status Register (MSR)..........................................................................7-8
7.3.5
M-Bus Data I/O Register (MDR) ......................................................................7-9
7.4
Programming Considerations ................................................................................7-11
7.4.1
Initialization ......................................................................................................7-11
7.4.2
Generation of a START Signal and the First Byte of Data Transfer..................7-11
7.4.3
Software Responses after Transmission or Reception of a Byte .....................7-11
7.4.4
Generation of the STOP Signal........................................................................7-12
7.4.5
Generation of a Repeated START Signal ........................................................7-13
7.4.6
Slave Mode ......................................................................................................7-13
7.4.7
Arbitration Lost .................................................................................................7-13
8
SYNC SIGNAL PROCESSOR
8.1
Functional Blocks...................................................................................................8-1
8.1.1
Polarity Correction............................................................................................8-1
8.1.1.1
Separate Vertical Sync Input ......................................................................8-2
8.1.1.2
Separate Horizontal Or Composite Sync Input ..........................................8-3
8.1.2
Sync Detection.................................................................................................8-3
8.1.3
Free-running Pseudo Sync Signal Generator ..................................................8-4
8.1.4
Sync Separation...............................................................................................8-4
8.1.5
Vertical Sync Pulse Reshaper..........................................................................8-5
8.1.6
Sync Signal Counters ......................................................................................8-5
8.2
VSYNC Interrupt....................................................................................................8-5
8.3
Registers ...............................................................................................................8-7
8.3.1
Sync Signal Control & Status Register (SSCSR).............................................8-7
8.3.2
Vertical Frequency Registers (VFRS) ..............................................................8-9
8.3.3
Line Frequency Registers (LFRs) ....................................................................8-9
8.3.4
Sync Signal Control Register (SSCR)..............................................................8-10
8.3.5
Horizontal Sync Period Width Register (HPWR)..............................................8-10
8.4
System Operation ..................................................................................................8-11
9
CPU CORE AND INSTRUCTION SET
9.1
Registers ...............................................................................................................9-1
9.1.1
Accumulator (A) ...............................................................................................9-1
9.1.2
Index register (X)..............................................................................................9-2
9.1.3
Program counter (PC) ......................................................................................9-2
9.1.4
Stack pointer (SP) ............................................................................................9-2
9.1.5
Condition code register (CCR).........................................................................9-2
TPG
MC68HC05BD3
MOTOROLA
iii
For More Information On This Product,
Go to: www.freescale.com
9
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Paragraph
Number
TITLE
Page
Number
9.2
Instruction set ........................................................................................................9-3
9.2.1
Register/memory Instructions ..........................................................................9-4
9.2.2
Branch instructions ..........................................................................................9-4
9.2.3
Bit manipulation instructions ............................................................................9-4
9.2.4
Read/modify/write instructions.........................................................................9-4
9.2.5
Control instructions ..........................................................................................9-4
9.2.6
Tables...............................................................................................................9-4
9.3
Addressing modes.................................................................................................9-11
9.3.1
Inherent............................................................................................................9-11
9.3.2
Immediate ........................................................................................................9-11
9.3.3
Direct ...............................................................................................................9-11
9.3.4
Extended..........................................................................................................9-12
9.3.5
Indexed, no offset ............................................................................................9-12
9.3.6
Indexed, 8-bit offset .........................................................................................9-12
9.3.7
Indexed, 16-bit offset .......................................................................................9-12
9.3.8
Relative ............................................................................................................9-13
9.3.9
Bit set/clear ......................................................................................................9-13
9.3.10
Bit test and branch...........................................................................................9-13
10
LOW POWER MODES
10.1
10.2
10.3
STOP Mode.........................................................................................................10-1
WAIT Mode..........................................................................................................10-1
COP Watchdog Timer Considerations.................................................................10-2
11
OPERATING MODES
11.1
11.2
11.3
User Mode (Normal Operation) ...........................................................................11-2
Self-Check Mode .................................................................................................11-2
Bootstrap Mode ...................................................................................................11-4
12
ELECTRICAL SPECIFICATIONS
12.1
12.2
12.3
12.4
12.5
12.6
Maximum Ratings................................................................................................12-1
Thermal Characteristics ......................................................................................12-1
DC Electrical Characteristics...............................................................................12-2
Control Timing .....................................................................................................12-3
M-Bus Timing ......................................................................................................12-4
Sync Signal Processor Timing.............................................................................12-5
TPG
MOTOROLA
iv
MC68HC05BD3
For More Information On This Product,
Go to: www.freescale.com
10
Freescale Semiconductor, Inc.
Paragraph
Number
TITLE
Page
Number
13
MECHANICAL SPECIFICATIONS
Freescale Semiconductor, Inc...
13.1
13.2
42-Pin SDIP Package (Case 858-01) ..................................................................13-1
40-Pin DIP Package (Case 711-03).....................................................................13-1
14
MC68HC705BD3
14.1
14.2
14.3
14.3.1
14.3.2
14.4
Features...............................................................................................................14-1
Memory Map........................................................................................................14-1
EPROM Programming .........................................................................................14-1
Programming Control Register (PCR)............................................................14-3
EPROM Programming Sequence ..................................................................14-3
DC Electrical Characteristics ...............................................................................14-4
15
MC68HC05BD5
15.1
15.2
15.3
Features...............................................................................................................15-1
Memory Map........................................................................................................15-1
DC Electrical Characteristics ...............................................................................15-3
TPG
MC68HC05BD3
MOTOROLA
v
For More Information On This Product,
Go to: www.freescale.com
11
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
THIS PAGE LEFT BLANK INTENTIONALLY
TPG
MOTOROLA
vi
MC68HC05BD3
For More Information On This Product,
Go to: www.freescale.com
12
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
LIST OF FIGURES
Figure
Number
1-1
2-1
2-2
2-3
3-1
4-1
4-2
4-3
6-1
7-1
7-2
7-3
7-4
8-1
8-2
8-3
8-4
8-5
8-6
9-1
9-2
10-1
11-1
11-2
11-3
12-1
14-1
15-1
TITLE
Page
Number
MC68HC05BD3/MC68HC705BD3/MC68HC05BD5 Block Diagram ......................1-2
Pin Assignment for 40-pin DIP Package.................................................................2-2
Pin Assignment for 42-pin SDIP Package ..............................................................2-3
Parallel Port I/O Circuitry ........................................................................................2-6
Memory Map ..........................................................................................................3-3
Power-On Reset and RESET Timing......................................................................4-2
Interrupt Stacking Order .........................................................................................4-4
External Interrupt Circuit and Timing ......................................................................4-6
8-Bit PWM Output Waveforms................................................................................6-2
M-Bus Interface Block Diagram ..............................................................................7-2
M-Bus Transmission Signal Diagram ......................................................................7-3
Clock Synchronization ............................................................................................7-5
Flowchart of M-Bus Interrupt Routine.....................................................................7-10
Sync Signal Processor Block Diagram ...................................................................8-2
Sync Signal Polarity Correction ..............................................................................8-3
Sync Separator.......................................................................................................8-4
Sync Signal Counters Block Diagram.....................................................................8-6
Vertical Frequency Counter Timing ........................................................................8-6
Typical Monitor System Operation..........................................................................8-12
Programming model ...............................................................................................9-1
Stacking order ........................................................................................................9-2
WAIT Flowchart ....................................................................................................10-2
Flowchart of Mode Entering .................................................................................11-1
Self-Check Mode Timing ......................................................................................11-2
MC68HC05BD3 Self-Test Circuit..........................................................................11-3
M-Bus Timing........................................................................................................12-4
MC68HC705BD3 Memory Map............................................................................14-2
MC68HC05BD5 Memory Map..............................................................................15-2
TPG
MC68HC05BD3
MOTOROLA
vii
For More Information On This Product,
Go to: www.freescale.com
\
13
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
THIS PAGE LEFT BLANK INTENTIONALLY
TPG
MOTOROLA
viii
MC68HC05BD3
For More Information On This Product,
Go to: www.freescale.com
14
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
LIST OF TABLES
Table
Number
2-1
2-2
3-1
4-1
5-1
7-1
8-1
9-1
9-2
9-3
9-4
9-5
9-6
9-7
9-8
11-1
11-2
12-1
12-2
12-3
12-4
12-5
14-1
14-2
15-1
TITLE
Page
Number
I/O Pin Functions ....................................................................................................2-4
Configuration for PC6 and PC7 ..............................................................................2-5
Register Outline......................................................................................................3-4
Reset/Interrupt Vector Addresses ..........................................................................4-4
COP Reset and RTI Rates .....................................................................................5-3
M-Bus Prescaler .....................................................................................................7-6
Vertical Frame Frequencies ....................................................................................8-9
MUL instruction.......................................................................................................9-5
Register/memory instructions.................................................................................9-5
Branch instructions .................................................................................................9-6
Bit manipulation instructions...................................................................................9-6
Read/modify/write instructions ...............................................................................9-7
Control instructions.................................................................................................9-7
Instruction set .........................................................................................................9-8
M68HC05 opcode map...........................................................................................9-10
Mode Selection.....................................................................................................11-2
Self-Check Report ................................................................................................11-4
DC Electrical Characteristics for MC68HC05BD3 ................................................12-2
Control Timing ......................................................................................................12-3
M-Bus Interface Input Signal Timing.....................................................................12-4
M-Bus Interface Output Signal Timing..................................................................12-4
Sync Signal Processor Timing..............................................................................12-5
MC68HC705BD3 Programming Boards...............................................................14-1
DC Electrical Characteristics for MC68HC705BD3 ..............................................14-4
DC Electrical Characteristics for MC68HC05BD5 ................................................15-3
TPG
MC68HC05BD3
MOTOROLA
ix
For More Information On This Product,
Go to: www.freescale.com
15
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
THIS PAGE LEFT BLANK INTENTIONALLY
TPG
MOTOROLA
x
MC68HC05BD3
For More Information On This Product,
Go to: www.freescale.com
16
Freescale Semiconductor, Inc.
1
1
Freescale Semiconductor, Inc...
GENERAL DESCRIPTION
The MC68HC05BD3 HCMOS microcontroller is a member of the M68HC05 Family of low-cost
single-chip microcontrollers. This 8-bit microcontroller unit (MCU) contains an on-chip oscillator,
CPU, RAM, ROM, parallel I/O capability with pins programmable as input or output, M-Bus serial
interface system (I2C), Pulse Width Modulator, Multi-Function Timer, and Sync Signal Processor.
These features make it particularly suitable as a multi-sync computer monitor MCU.
The MC68HC05BD5 is functionally equivalent to MC68HC05BD3, with increase RAM and ROM.
The MC68HC705BD3 is an EPROM version of the MC68HC05BD5. All references to the
MC68HC05BD3 apply equally to the MC68HC705BD3 and MC68HC05BD5, unless otherwise
stated. References specific to the MC68HC705BD3 are italicized in the text and also, for quick
reference, they are summarized in Section 14. References to MC68HC05BD5 are summarized in
Section 15.
1.1
Features
•
Fully static chip design featuring the industry standard 8-bit M68HC05 core
•
Power saving Wait mode
•
128 bytes of on-chip RAM for MC68HC05BD3
256 bytes for MC68HC705BD3 and MC68HC05BD5
•
3.75K-bytes of user ROM for MC68HC05BD3
7.75K-bytes of user ROM for MC68HC05BD5
7.75K-bytes of user EPROM for MC68HC705BD3
•
24 bidirectional I/O lines: 14 dedicated and 10 multiplexed I/O lines.
4 of the 14 dedicated I/O lines and 6 of the MUXed I/O lines have +10V open-drain O/Ps.
•
16 channels PWM outputs: 8 dedicated, +10V open-drain PWM channels and
8 multiplexed with I/O lines of which 6 of them have +10V open-drain outputs.
•
M-Bus Serial Interface (I2C-bus†)
•
Multi-Function Timer (MFT) with Periodic Interrupt
•
COP watchdog reset
†
I2C-bus is a proprietary Philips interface bus
TPG
MC68HC05BD3
GENERAL DESCRIPTION
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
1-1
17
Freescale Semiconductor, Inc.
Horizontal and Vertical Sync Signal Processor
•
Self-check mode
•
Available in 40-pin DIP and 42-pin SDIP packages
DDR A
•
8
PA0 - PA7
7.75K-Bytes EPROM for MC68HC705BD3
DDR B
128 Bytes for MC68HC05BD3
256 Bytes for MC68HC705BD3 & MC68HC05BD5
SELF-CHECK ROM - 224 Bytes
for MC68HC05BD3 & MC68HC05BD5 only
PORT B
RAM
PB0
PB1
4
PB2* - PB5*
BOOTSTRAP ROM - 480 Bytes
for MC68HC705BD3 only
7
M68HC05
CPU
PWM0*
PWM1*
PWM2*
PWM3*
PWM4*
PWM5*
PWM6*
PWM7*
0
ACCUMULATOR
7
0
PWM
INDEX REGISTER
5
12
0 0 0 0 0 1 1
0
PC0/PWM8*
PC1/PWM9*
PC2/PWM10*
PC3/PWM11*
PC4/PWM12*
PC5/PWM13*
PC6/PWM14/VTTL
PC7/PWM15/HTTL
STACK POINTER
0
DDR C
4
PROGRAM COUNTER
RESET
RESET
7
0
1 1 1 H I N Z C
CONDITION CODE REGISTER
SYNC
SIGNAL
PROCESSOR
(SSP)
MFT
(with COP)
EXTAL
OSC
÷2
XTAL
VSYNC
HSYNC
POWER
M-BUS
VDD
PORT D
IRQ/VPP
PORT C
15
0 0
DDR D
Freescale Semiconductor, Inc...
USER ROM
3.75K-Bytes for MC68HC05BD3
7.75K-Bytes for MC68HC05BD5
PORT A
1
PD0/SDA†
PD1/SCL†
VSS
* +10V open-drain
† +5V open-drain if the pin is configured as SDA or SCL
Figure 1-1 MC68HC05BD3/MC68HC705BD3/MC68HC05BD5 Block Diagram
TPG
MOTOROLA
1-2
GENERAL DESCRIPTION
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
18
Freescale Semiconductor, Inc.
2
2
Freescale Semiconductor, Inc...
PIN DESCRIPTION AND I/O PORTS
This section provides a description of the functional pins and I/O programming of the
MC68HC05BD3 microcontroller.
2.1
PIN DESCRIPTIONS
40-pin DIP
PIN No.
42-pin SDIP
PIN No.
VDD, VSS
5, 6
5, 7
IRQ/VPP
15
16
RESET
4
4
7, 8
8, 9
PA0-PA7
23-16
24-17
PB0-PB5
14-9
15-10
PC0/PWM8
to
PC5/PWM13
26-31
27-32
PIN NAME
XTAL, EXTAL
DESCRIPTION
Power is supplied to the MCU using these two pins. VDD is power and
VSS is ground.
In the user mode this pin an external hardware interrupt IRQ. It is
software programmable to provide two choices of interrupt triggering
sensitivity. These options are:
1) negative edge-sensitive triggering only, or
2) both negative edge-sensitive and level sensitive triggering.
In the bootstrap mode on the MC68HC705BD3, this is the EPROM
programming voltage input pin.
The active low RESET input is not required for start-up, but can be
used to reset the MCU internal state and provide an orderly software
start-up procedure.
These pins provide connections to the on-chip oscillator. The
oscillator can be driven by a AT-crystal circuit or a ceramic resonator
with a frequency of 4.2 MHz. EXTAL may also be driven by an
external oscillator if an external crystal/resonator circuit is not used.
See Figure 11-3 for values of crystal circuit external components.
These eight I/O lines comprise port A. The state of any pin is software
programmable. All port A lines are configured as input during power
on or external reset.
These six I/O lines comprise port B. The state of any pin is software
programmable. All port B lines are configured as input during power
on or external reset. PB2 to PB5 are +10V open-drain pins.
These six port C pins are +10V open-drain type. The state of any pin
is software programmable. All port C lines are configured as input
during power on or external reset.
These pins become PWM output channels 8 to 13 by setting the
appropriate bits in Configuration register 1 ($0A).
TPG
MC68HC05BD3
PIN DESCRIPTION AND I/O PORTS
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
2-1
19
Freescale Semiconductor, Inc.
2
PIN NAME
40-pin DIP
PIN No.
42-pin SDIP
PIN No.
PC6/PWM14/VTTL,
PC7/PWM15/HTTL
32, 33
33, 34
PD0/SDA,
PD1/SCL
24, 25
25, 26
3-1, 38-34
3-1, 40-38, 36,
35
Freescale Semiconductor, Inc...
PWM0 to PWM7
HSYNC, VSYNC
2.2
39, 40
41, 42
DESCRIPTION
These two port C I/O lines are shared with the PWM and Sync Signal
Processor. Configuration for use are set by the Configuration
register 1 ($0A) and Configuration register 2 ($0B).
These two port D I/O lines are shared with the M-Bus lines SDA and
SCL. When configured as M-Bus lines in Configuration
register 2 ($0B), these pins become +5V open-drain pins.
These eight pins are dedicated for the 8-bit PWM channel 0 to 7.
These two pins are for video sync signals input from the host
computer. The polarity of the input signals can either be positive or
negative. These two pins contain internal Schmitt triggers as part of
their inputs to improve noise immunity
Pin Assignments
PWM2
1
40
VSYNC
PWM1
2
39
HSYNC
PWM0
3
38
PWM3
RESET
4
37
PWM4
VDD
5
36
PWM5
VSS
6
35
PWM6
XTAL
7
34
PWM7
EXTAL
8
33
PC7/PWM15/HTTL
PB5
9
32
PC6/PWM14/VTTL
PB4
10
31
PC5/PWM13
PB3
11
30
PC4/PWM12
PB2
12
29
PC3/PWM11
PB1
13
28
PC2/PWM10
PB0
14
27
PC1/PWM9
IRQ/VPP
15
26
PC0/PWM8
PA7
16
25
PD1/SCL
PA6
17
24
PD0/SDA
PA5
18
23
PA0
PA4
19
22
PA1
PA3
20
21
PA2
Figure 2-1 Pin Assignment for 40-pin DIP Package
TPG
MOTOROLA
2-2
PIN DESCRIPTION AND I/O PORTS
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
20
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
PWM2
PWM1
PWM0
RESET
VDD
NC
VSS
XTAL
EXTAL
PB5
PB4
PB3
PB2
PB1
PB0
IRQ/VPP
PA7
PA6
PA5
PA4
PA3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
2
VSYNC
HSYNC
PWM3
PWM4
PWM5
NC
PWM6
PWM7
PC7/PWM15/HTTL
PC6/PWM14/VTTL
PC5/PWM13
PC4/PWM12
PC3/PWM11
PC2/PWM10
PC1/PWM9
PC0/PWM8
PD1/SCL
PD0/SDA
PA0
PA1
PA2
Figure 2-2 Pin Assignment for 42-pin SDIP Package
2.3
INPUT/OUTPUT PORTS
In the User Mode there are 24 bidirectional I/O lines arranged as 4 I/O ports (Port A, B, C, and D).
The individual bits in these ports are programmable as either inputs or outputs under software
control by the data direction registers (DDRs). Also, if enabled by software, Port C and D will have
additional functions as PWM outputs, M-Bus I/O and Sync Signal Processor outputs.
2.3.1
Port A
Port A is an 8-bit bidirectional port which does not share any of its pins with other subsystems.
The Port A data register is at $00 and the data direction register (DDR) is at $04. Reset does not
affect the data register, yet clears the data direction register, thereby returning the ports to inputs.
Writing a one to a DDR bit sets the corresponding port bit to output mode.
2.3.2
Port B
Port B is a 6-bit bidirectional port which does not share any of its pins with other subsystems. PB2
to PB5 are +10V open-drain port pins. The Port B data register is at $01 and the data direction
register (DDR) is at $05. Reset does not affect the data register, yet clears the data direction
register, thereby returning the ports to inputs. Writing a one to a DDR bit sets the corresponding
port bit to output mode.
TPG
MC68HC05BD3
PIN DESCRIPTION AND I/O PORTS
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
2-3
21
Freescale Semiconductor, Inc.
2.3.3
Freescale Semiconductor, Inc...
2
Port C
Port C is an 8-bit bidirectional port which shares pins with PWM and SSP subsystem. See
Section 6 for a detailed description of PWM and Section 8 for a detailed description of SSP. These
pins are configured to PWM output when the corresponding bits in the Configuration register 1 are
set, except PC6 and PC7. PC6 and PC7 are configured to SSP outputs when the corresponding
bits in the Configuration register 2 are set. The Port C data register is at $02 and the data direction
register (DDR) is at $06. Reset does not affect the data register, but clears the data direction
register, thereby returning the ports to inputs. Writing a one to a DDR bit sets the corresponding
port bit to output mode.
2.3.4
Port D
Port D is a 2-bit bidirectional port which shares pins with M-Bus subsystem. See Section 7 for a
detailed description of M-Bus. These pins are configured to the corresponding functions when the
corresponding bits in the Configuration register 2 are set. They are +5V open-drain I/O pins when
used as M-Bus I/O. The Port D data register is at $03 and the data direction register (DDR) is at
$07. Reset does not affect the data register, yet clears the data direction register, thereby returning
the ports to inputs. Writing a one to a DDR bit sets the corresponding port bit to output mode.
2.3.5
Input/Output Programming
Bidirectional port lines may be programmed as an input or an output under software control. The
direction of the pins is determined by the state of the corresponding bit in the port data direction
register (DDR). Each port has an associated DDR. Any I/O port pin is configured as an output if
its corresponding DDR bit is set. A pin is configured as an input if its corresponding DDR bit is
cleared.
During Reset, all DDRs are cleared, which configure all port pins as inputs. The data direction
registers are capable of being written to or read by the processor. During the programmed output
state, a read of the data register actually reads the value of the output data latch and not the I/O
pin.
Table 2-1 I/O Pin Functions
R/W
0
0
1
1
DDR
0
1
0
1
I/O Pin Function
The I/O pin is in input mode. Data is written into the output data latch.
Data is written into the output data latch and output to the I/O pin.
The state of the I/O pin is read.
The I/O pin is in an output mode. The output data latch is read.
TPG
MOTOROLA
2-4
PIN DESCRIPTION AND I/O PORTS
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
22
Freescale Semiconductor, Inc.
2.3.6
Port C and D Configuration Registers
Port C and Port D are shared with PWM, M-Bus and SSP. The configuration registers at $0A and
$0B are used to configure those I/O pins. They are default to zero after power-on reset. Setting
these bits will set the corresponding pins to the corresponding functions, except PC6 and PC7.
For example, setting SCL and SDA bits of register $0B will configure Port D pins 1 and 0 as M-Bus
pins, regardless of DDR1 and DDR0 settings.
Freescale Semiconductor, Inc...
Address bit 7
Configuration Register 1
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
2
State
on reset
$000A PWM15 PWM14 PWM13 PWM12 PWM11 PWM10 PWM9 PWM8 0000 0000
Address bit 7
Configuration Register 2
$000B
HTTL
bit 6
bit 5
bit 4
bit 3
bit 2
VTTL
bit 1
bit 0
State
on reset
SCL
SDA
0000 0000
PC7 and PC6 are shared with both PWM and SSP. When HTTL and VTTL in $000B are set, PC7
and PC6 are configured as HTTL and VTTL outputs respectively, regardless of the status of
PWM15 and PWM14 in $000A. That is, HTTL and VTTL settings override PWM15 and PWM14
settings.
Table 2-2 Configuration for PC6 and PC7
PWM15
0
0
1
1
HTTL
0
1
0
1
Result of PC7
PC7
HTTL
PWM15
HTTL
PWM14
0
0
1
1
VTTL
0
1
0
1
Result of PC6
PC6
VTTL
PWM14
VTTL
TPG
MC68HC05BD3
PIN DESCRIPTION AND I/O PORTS
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
2-5
23
Freescale Semiconductor, Inc.
2
DATA DIRECTION
REGISTER BIT
Freescale Semiconductor, Inc...
INTERNAL
MC68HC05
CONNECTIONS
LATCHED OUTPUT
DATA BIT
OUTPUT
I/O PIN
INPUT
REGISTER
BIT
INPUT I/O
(a)
TYPICAL PORT
DATA DIRECTION REGISTER
7
6
5
4
3
2
1
0
DDR 7
DDR 6
DDR 5
DDR 4
DDR 3
DDR 2
DDR 1
DDR 0
Px2
Px1
TYPICAL PORT REGISTER
I/O PORT LINES
Px7
Px6
Px5
Px3
Px4
Px0
(b)
VDD
NOTE:
(1) IP = INPUT PROTECTION
(2) LATCH-UP PROTECTION NOT SHOWN
PORT DATA
&
P
PORT DDR
PAD
+
N
IP
INTERNAL LOGIC
(c)
Figure 2-3 Parallel Port I/O Circuitry
TPG
MOTOROLA
2-6
PIN DESCRIPTION AND I/O PORTS
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
24
Freescale Semiconductor, Inc.
3
3
Freescale Semiconductor, Inc...
MEMORY AND REGISTERS
The MC68HC05BD3/MC68HC705BD3/MC68HC05BD5 has a 16K-byte memory map consisting
of registers, user ROM/EPROM, user RAM, self-check/bootstrap ROM, and I/O as shown in
Figure 3-1.
3.1
Registers
All the I/O, control and status registers of the MC68HC05BD3 are contained within the first 48-byte
block of the memory map (address $0000 to $002F).
3.2
RAM (MC68HC05BD3)
The user RAM consists of 128 bytes of memory, from $0080 to $00FF. This is shared with a 64
byte stack area. The stack begins at $00FF and counts down to $00C0.
3.3
RAM (MC68HC705BD3/MC68HC05BD5)
The user RAM consists of 256 bytes of memory, from $0080 to $017F. This is shared with a 64
byte stack area. The stack begins at $00FF and counts down to $00C0.
Note:
Using the stack area for data storage or temporary work locations requires care to
prevent the data from being overwritten due to stacking from an interrupt or subroutine
call.
TPG
MC68HC05BD3
MEMORY AND REGISTERS
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
3-1
25
Freescale Semiconductor, Inc.
3.4
ROM (MC68HC05BD3)
The user ROM consists of 3.75K-bytes of memory, from $3000 to $3EFF.
3
3.5
ROM (MC68HC05BD5)
Freescale Semiconductor, Inc...
The user ROM consists of 7.75K-bytes of memory, from $2000 to $3EFF.
3.6
EPROM (MC68HC705BD3)
The user EPROM consists of 7.75K-bytes of memory, from $2000 to $3EFF.
3.7
Bootstrap ROM
This is available on the MC68HC705BD3 device only. It stores the on-chip program for
programming the user EPROM.
TPG
MOTOROLA
3-2
MEMORY AND REGISTERS
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
26
Freescale Semiconductor, Inc.
$002F
$0030
I/O
48 Bytes
$0000
$002F
$0030
Unused
$007F
$0080
$00C0
Freescale Semiconductor, Inc...
$00FF
$0100
I/O
48 Bytes
Stack
64 Bytes
$0000
Unused
Unused
$007F
$0080
$00C0
$00FF
Port A Data Register
Port B Data Register
Port C Data Register
Port D Data Register
Port A Data Direction Register
Port B Data Direction Register
Port C Data Direction Register
Port D Data Direction Register
MFT Control and Status Register
MFT Timer Counter Register
Configuration Register 1
Configuration Register 2
SSP Control and Status Register
Vertical Frequency High Register
Vertical Frequency Low Register
Line Frequency High Register
Line Frequency Low Register
Sync Signal Control Register
Unused
Unused
Unused
Unused
Unused
MBUS Address Register
MBUS Frequency Divider Register
MBUS Control Register
MBUS Status Register
MBUS Data Register
Unused
Programming Control Register
HSYNC Period Width Register
Reserved
PWM0
PWM1
PWM2
PWM3
PWM4
PWM5
PWM6
PWM7
PWM8
PWM9
PWM10
PWM11
PWM12
PWM13
PWM14
PWM15
I/O
48 Bytes
$002F
$0030
$007F
$0080
User RAM
128 Bytes
MC68HC705BD3
MC68HC05BD5
MC68HC05BD3
$0000
$00C0
Stack
64 Bytes
$00FF
User RAM
256 Bytes
User RAM
256 Bytes
$017F
$0180
Stack
64 Bytes
$017F
$0180
Unused
Unused
Unused
$1DFF
$1E00
Bootstrap ROM
480 Bytes
$1FDF
$1FE0
$1FFF
$2000
$1FFF
$2000
$2FFF
$3000
Unused
User EPROM
7936 Bytes
User ROM
7936 Bytes
User ROM
3840 Bytes
$3EFF
$3F00
$3FDF
$3FE0
$3FEF
$3FF0
$3FFF
Self-Check
Program
224 Bytes
Self-Check
Vectors
16 Bytes
User Vectors
16 Bytes
$3EFF
$3F00
$3FDF
$3FE0
$3FEF
$3FF0
$3FFF
Self-Check
Program
224 Bytes
Self-Check
Vectors
16 Bytes
User Vectors
16 Bytes
$3EFF
$3F00
Unused
$3FDF
$3FE0
$3FEF
$3FF0
Bootstrap
Vectors
16 Bytes
User Vectors
16 Bytes
$00
$01
$02
$03
$04
$05
$06
$07
$08
$09
$0A
$0B
3
$0C
$0D
$0E
$0F
$10
$11
$12
$13
$14
$15
$16
$17
$18
$19
$1A
$1B
$1C
$1D
$1E
$1F
$20
$21
$22
$23
$24
$25
$26
$27
$28
$29
$2A
$2B
$2C
$2D
$2E
$2F
$3FFF
$3FF0
$3FF2
$3FF4
$3FF6
$3FF8
$3FFA
$3FFC
$3FFE
Reserved
Reserved
MFT
MBUS
SSP
IRQ
SWI
RESET
Figure 3-1 Memory Map
TPG
MC68HC05BD3
MEMORY AND REGISTERS
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
3-3
27
Freescale Semiconductor, Inc.
Table 3-1 Register Outline
Freescale Semiconductor, Inc...
3
Register Name
Port A data
$0000
Port B data
$0001
Port C data
$0002
Port D data
$0003
Port A data direction
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
State
on reset
PA7
PA6
PA5
PA4
PA3
PA2
PA1
PA0
undefined
PB5
PB4
PB3
PB2
PB1
PB0
undefined
PC7
PC6
PC5
PC4
PC3
PC2
PC1
PC0
undefined
PD1
PD0
undefined
Address bit 7
$0004 DDRA7 DDRA6 DDRA5 DDRA4 DDRA3 DDRA2 DDRA1 DDRA0 0000 0000
Port B data direction
$0005
Port C data direction
$0006 DDRC7 DDRC6 DDRC5 DDRC4 DDRC3 DDRC2 DDRC1 DDRC0 0000 0000
Port D data direction
$0007
MFT control and status
$0008
DDRB5 DDRB4 DDRB3 DDRB2 DDRB1 DDRB0 --00 0000
DDRD1 DDRD0
TOF
RTIF
TOFIE
RTIE
IRQN
RT1
RT0
---- --00
0000 0-11
MFT timer counter
$0009 MFTCR7 MFTCR6 MFTCR5 MFTCR4 MFTCR3 MFTCR2 MFTCR1 MFTCR0 0000 0000
Configuration 1
$000A PWM15 PWM14 PWM13 PWM12 PWM11 PWM10 PWM9 PWM8 0000 0000
Configuration 2
$000B
HTTL
SCL
SDA
00-- --00
SSP control and status
$000C
VPOL HPOL VDET HDET SOUT INSRTB FOUT
VTTL
VSIN
0000 0000
Vertical frequency high
$000D
0
0
0
VF12
VF11
VF10
VF9
VF8
0000 0000
Vertical frequency low
$000E
VF7
VF6
VF5
VF4
VF3
VF2
VF1
VF0
0000 0000
Line frequency high
$000F HOVER
0
0
0
LF11
LF10
LF9
LF8
0000 0000
Line frequency low
$0010
LF7
LF6
LF5
LF4
LF3
LF2
LF1
LF0
0000 0000
Sync signal control
$0011
VSIE
0
0
0
0
0
0
0
0000 0000
Unused
$0012
Unused
$0013
Unused
$0014
Unused
$0015
Unused
$0016
MBUS address
$0017
MAD7 MAD6 MAD5 MAD4 MAD3 MAD2 MAD1
MBUS frequency divider
$0018
FD4
FD3
TXAK
0000 000-
FD2
FD1
FD0
---0 0000
SRW
MIF
RXAK 1000 -001
MD2
MD1
MD0
undefined
ELAT
PGM
---- --00
MBUS control
$0019
MEN
MIEN
MSTA
MTX
MBUS status
$001A
MCF
MASS
MBB
MAL
MBUS data
$001B
MD7
MD6
MD5
MD4
Unused
$001C
Programming Control
$001D
HSYNC period width
$001E HPWR7 HPWR6 HPWR5 HPWR4 HPWR3 HPWR2 HPWR1 HPWR0 0000 0000
Reserved
MD3
0000 0---
$001F
TPG
MOTOROLA
3-4
MEMORY AND REGISTERS
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
28
Freescale Semiconductor, Inc.
Table 3-1 Register Outline
Freescale Semiconductor, Inc...
Register Name
Address bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
State
on reset
0PWM
$0020 0PWM4 0PWM3 0PWM2 0PWM1 0PWM0 0BRM2 0BRM1 0BRM0 0000 0000
1PWM
$0021 1PWM4 1PWM3 1PWM2 1PWM1 1PWM0 1BRM2 1BRM1 1BRM0 0000 0000
2PWM
$0022 2PWM4 2PWM3 2PWM2 2PWM1 2PWM0 2BRM2 2BRM1 2BRM0 0000 0000
3PWM
$0023 3PWM4 3PWM3 3PWM2 3PWM1 3PWM0 3BRM2 3BRM1 3BRM0 0000 0000
4PWM
$0024 4PWM4 4PWM3 4PWM2 4PWM1 4PWM0 4BRM2 4BRM1 4BRM0 0000 0000
5PWM
$0025 5PWM4 5PWM3 5PWM2 5PWM1 5PWM0 5BRM2 5BRM1 5BRM0 0000 0000
6PWM
$0026 6PWM4 6PWM3 6PWM2 6PWM1 6PWM0 6BRM2 6BRM1 6BRM0 0000 0000
7PWM
$0027 7PWM4 7PWM3 7PWM2 7PWM1 7PWM0 7BRM2 7BRM1 7BRM0 0000 0000
8PWM
$0028 8PWM4 8PWM3 8PWM2 8PWM1 8PWM0 8BRM2 8BRM1 8BRM0 0000 0000
9PWM
$0029 9PWM4 9PWM3 9PWM2 9PWM1 9PWM0 9BRM2 9BRM1 9BRM0 0000 0000
10PWM
$002A 10PWM4 10PWM3 10PWM2 10PWM1 10PWM0 10BRM2 10BRM1 10BRM0 0000 0000
11PWM
$002B 11PWM4 11PWM3 11PWM2 11PWM1 11PWM0 11BRM2 11BRM1 11BRM0 0000 0000
12PWM
$002C 12PWM4 12PWM3 12PWM2 12PWM1 12PWM0 12BRM2 12BRM1 12BRM0 0000 0000
13PWM
$002D 13PWM4 13PWM3 13PWM2 13PWM1 13PWM0 13BRM2 13BRM1 13BRM0 0000 0000
14PWM
$002E 14PWM4 14PWM3 14PWM2 14PWM1 14PWM0 14BRM2 14BRM1 14BRM0 0000 0000
15PWM
$002F 15PWM4 15PWM3 15PWM2 15PWM1 15PWM0 15BRM2 15BRM1 15BRM0 0000 0000
3
TPG
MC68HC05BD3
MEMORY AND REGISTERS
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
3-5
29
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
3
THIS PAGE LEFT BLANK INTENTIONALLY
TPG
MOTOROLA
3-6
MEMORY AND REGISTERS
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
30
Freescale Semiconductor, Inc.
4
Freescale Semiconductor, Inc...
RESETS AND INTERRUPTS
4.1
4
RESETS
The MC68HC05BD3 can be reset in four ways: by the initial power-on reset function, by an active
low input to the RESET pin, by an opcode fetch from an illegal address, and by a COP watchdog
timer reset. Any of these resets will cause the program to go to its starting address, specified by
the contents of memory locations $3FFE and $3FFF, and cause the interrupt mask of the
Condition Code register to be set.
4.1.1
Power-On Reset (POR)
The power-on reset occurs when a positive transition is detected on the supply voltage, VDD. The
power-on reset is used strictly for power-up conditions, and should not be used to detect any drops
in the power supply voltage. There is no provision for a power-down reset. The power-on circuitry
provides for a 4064 tcyc delay from the time that the oscillator becomes active. If the external
RESET pin is low at the end of the 4064 tcyc time out, the processor remains in the reset condition
until RESET goes high. The user must ensure that VDD has risen to a point where the MCU can
operate properly prior to the time the 4064 POR cycles have elapsed. If there is doubt, the external
RESET pin should remain low until such time that VDD has risen to the minimum operating voltage
specified.
4.1.2
RESET Pin
The RESET input pin is used to reset the MCU to provide an orderly software start-up procedure.
When using the external reset, the RESET pin must stay low for a minimum of 1.5tcyc. The
RESET pin contains an internal Schmitt Trigger as part of its input to improve noise immunity.
TPG
MC68HC05BD3
RESETS AND INTERRUPTS
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
4-1
31
Freescale Semiconductor, Inc.
t
VDDR
VDD
VDD THRESHOLD (TYPICALLY 1-2V)
XTAL PIN1
toxov
Freescale Semiconductor, Inc...
4
4064 tcyc
tcyc
INTERNAL
CLOCK2
INTERNAL
ADDRESS
BUS2
INTERNAL
DATA
BUS2
3FFE
NEW
PCL
3FFF
NEW
PCH
NEW PC
3FFE
OP
CODE
3FFE
3FFF
NEW PC
PCL
OP
CODE
PCH
tRL =1.5tCYC
3
RESET
NOTES:
1. XTAL is not meant to represent frequency. It is only used to represent time.
2. Internal clock, internal address bus, and internal data bus signals are not available externally.
3. Next rising edge of internal clock after rising edge of RESET initiates reset sequence.
Figure 4-1 Power-On Reset and RESET Timing
4.1.3
Illegal Address (ILADR) Reset
The MCU monitors all opcode fetches. If an illegal address space is accessed during an opcode
fetch, an internal reset is generated. Illegal address spaces consist of all unused locations within
the memory map and the I/O registers (see Figure 3-1). Because the internal reset signal is used,
the MCU comes out of an ILADR reset in the same operating mode it was in when the opcode was
fetched.
4.1.4
Computer Operating Properly (COP) Reset
The MCU contains a watchdog timer that automatically times out if not reset (cleared) within a
specific amount of time by a program reset sequence.
TPG
MOTOROLA
4-2
RESETS AND INTERRUPTS
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
32
Freescale Semiconductor, Inc.
Note:
COP time-out is prevented by periodically writing a “0” to bit 0 of address $3FF0.
If the watchdog timer is allowed to time-out, an internal reset is generated to reset the MCU.
Because the internal reset signal is used, the MCU comes out of a COP reset in the same
operating mode it was in when the COP time-out was generated.
The COP reset function is always enabled.
See Section 5.3 for more information on the COP watchdog timer.
Freescale Semiconductor, Inc...
4
4.2
INTERRUPTS
The MCU can be interrupted by different sources – four maskable hardware interrupt and one
non-maskable software interrupt:
•
External signal on the IRQ pin
•
Multi-Function Timer (MFT)
•
M-Bus Interface (MBUS)
•
Sync Signal Processor (SSP)
•
Software Interrupt Instruction (SWI)
If the interrupt mask bit (I-bit) of the CCR is set, all maskable interrupts (internal and external) are
disabled. Clearing the I-bit enables interrupts.
Interrupts cause the processor to save the register contents on the stack and to set the interrupt
mask (I-bit) to prevent additional interrupts. The RTI instruction causes the register contents to be
recovered from the stack and normal processing to resume.
Unlike reset, hardware interrupts do not cause the current instruction execution to be halted, but
are considered pending until the current instruction is complete. The current instruction is the one
already fetched and being operated on. When the current instruction is complete, the processor
checks all pending hardware interrupts. If interrupts are not masked (CCR I-bit clear) the
processor proceeds with interrupt processing; otherwise, the next instruction is fetched and
executed.
Table 4-1 shows the relative priority of all the possible interrupt sources.
4.2.1
Non-maskable Software Interrupt (SWI)
The software interrupt (SWI) is an executable instruction and a non-maskable interrupt: it is
execute regardless of the state of the I-bit in the CCR. If the I-bit is zero (interrupt enabled), SWI
is executed after interrupts that were pending when the SWI was fetched, but before interrupts
generated after the SWI was fetched. The SWI interrupt service routine address is specified by
the contents of memory locations $3FFC and $3FFD.
TPG
MC68HC05BD3
RESETS AND INTERRUPTS
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
4-3
33
Freescale Semiconductor, Inc.
$00C0 (BOTTOM OF STACK)
$00C1
UNSTACKING
ORDER
Freescale Semiconductor, Inc...
4
$00C2
•
•
•
•
•
•
CONDITION CODE REGISTER
5
1
4
2
ACCUMULATOR
3
3
INDEX REGISTER
2
4
PROGRAM COUNTER (HIGH BYTE)
1
5
PROGRAM COUNTER (LOW BYTE)
STACKING
ORDER
•
•
•
•
•
•
$00FD
$00FE
$00FF (TOP OF STACK)
Figure 4-2 Interrupt Stacking Order
Table 4-1 Reset/Interrupt Vector Addresses
Register
–
–
–
SSCR
MSR
MFTCSR
–
–
Flag Name
–
–
–
–
MIF
TOF
RTIF
–
–
Interrupt
Reset
Software
External Interrupt
VSYNC
M-Bus
Timer Overflow
Real Time Interrupt
–
–
CPU Interrupt
RESET
SWI
IRQ
SSP
MBUS
Vector Address
$3FFE-$3FFF
$3FFC-$3FFD
$3FFA-$3FFB
$3FF8-$3FF9
$3FF6-$3FF7
MFT
$3FF4-$3FF5
–
–
$3FF2-$3FF3
$3FF0-$3FF1
Priority
highest
lowest
TPG
MOTOROLA
4-4
RESETS AND INTERRUPTS
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
34
Freescale Semiconductor, Inc.
4.2.2
Maskable Hardware Interrupts
If the interrupt mask bit (I-bit) of the CCR is set, all maskable interrupts (internal and external) are
masked. Clearing the I-bit allows interrupt processing to occur.
Freescale Semiconductor, Inc...
Note:
The internal interrupt latch is cleared in the first part of the interrupt service routine;
therefore, one external interrupt pulse could be latched and serviced as soon as the
I-bit is cleared.
4.2.2.1
4
External Interrupt (IRQ)
The external interrupt IRQ can be software configured for “negative-edge” or “negative-edge and
level” sensitive triggering by the IRQN bit in the Multi-Function TImer Control and Status
register.
Address bit 7
MFT Control and Status
$0008
TOF
bit 6
bit 5
bit 4
bit 3
RTIF
TOFIE
RTIE
IRQN
bit 2
bit 1
bit 0
State
on reset
RT1
RT0
0000 0-11
IRQN
1 (set)
–
0 (clear) –
Negative edge triggering for IRQ only
Level and negative edge triggering for IRQ
When the signal of the external interrupt pin, IRQ, satisfies the condition selected, an external
interrupt occurs. The actual processor interrupt is generated only if the interrupt mask bit of the
condition code register is also cleared. When the interrupt is recognized, the current state of the
processor is pushed onto the stack and the interrupt mask bit in the condition code register is set.
This masks further interrupts until the present one is serviced. The service routine address is
specified by the contents $3FFA & $3FFB.
The interrupt logic recognizes negative edge transitions and pulses (special case of negative
edges) on the external interrupt line. Figure 4-3 shows both a block diagram and timing for the
interrupt line (IRQ) to the processor. The first method is used if pulses on the interrupt line are
spaced far enough apart to be serviced. The minimum time between pulses is equal to the number
of cycles required to execute the interrupt service routine plus 21 cycles. Once a pulse occurs, the
next pulse should not occur until the MCU software has exited the routine (an RTI occurs). The
second configuration shows several interrupt lines wired-OR to perform the interrupt at the
processor. Thus, if the interrupt lines remain low after servicing one interrupt, the next interrupt is
recognized.
Note:
The internal interrupt latch is cleared in the first part of the service routine; therefore,
one (and only one) external interrupt pulse could be latched during tILIL and serviced
as soon as the I bit is cleared.
TPG
MC68HC05BD3
RESETS AND INTERRUPTS
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
4-5
35
Freescale Semiconductor, Inc.
IRQN bit
&
+
4
Freescale Semiconductor, Inc...
&
VDD
Q
D
IRQ pin
External
Interrupt
Request
I BIT (CCR)
C
Q
R
Power-On Reset
+
External Reset
External Interrupt
being serviced
(read of vectors)
(a) Interrupt Function Diagram
EDGE SENSITIVE TRIGGER
CONDITION
IRQ
tILIH
tILIL
tILIL
The minimum pulse width tILIH is one
internal bus period. The period tILIL
should not be less than the number of
tCYC cycles it takes to execute the
interrupt service routine plus 21 tcyc
cycles.
LEVEL SENSITIVE TRIGGER
CONDITION
If after servicing an interrupt the IRQ
pin remains low, then the next interrupt
is recognized. Normally used with wired
OR connection.
Wired ORed
Interrupt signals
Normally used with pull-up resistors for
wired-OR connection.
IRQ
(b) Interrupt Mode Diagram
Figure 4-3 External Interrupt Circuit and Timing
TPG
MOTOROLA
4-6
RESETS AND INTERRUPTS
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
36
Freescale Semiconductor, Inc.
4.2.2.2
Sync Signal Processor Interrupt
The VSYNC interrupt is generated by the Sync Signal Processor (SSP) after a vertical sync pulse
is detected as described in Section 8. The interrupt enable bit, VSIE, for the VSYNC interrupt is
located at bit 7 of Sync Signal Control register (SSCR) at $0011. The I-bit in the CCR must be
cleared in order for the VSYNC interrupt to be enabled. This interrupt will vector to the interrupt
service routine located at the address specified by the contents of $3FF8 and $3FF9. The VSYNC
interrupt latch will be cleared automatically by fetching of these vectors.
4
Freescale Semiconductor, Inc...
Refer to Section 8 for detailed description of Sync Signal Processor.
4.2.2.3
M-Bus Interrupts
M-Bus interrupt is enabled when the M-Bus Interrupt Enable bit (MIEN) of M-Bus Control register
is set, provided the interrupt mask bit of the Condition Code register is cleared. The interrupt
service routine address is specified by the contents of memory location $3FF6 and $3FF7.
Address bit 7
M-Bus Status Register
$001A
MCF
bit 6
bit 5
bit 4
MAAS
MBB
MAL
bit 3
bit 2
bit 1
SRW
MIF
bit 0
State
on reset
RXAK 1000 0001
MIF - M-Bus Interrupt
1 (set)
–
0 (clear) –
An M-Bus interrupt has occurred.
An M-Bus interrupt has not occurred.
When this bit is set, an interrupt is generated to the CPU if MIEN is set. This bit is set when one
of the following events occurs:
1) Completion of one byte of data transfer. It is set at the falling edge of the 9th
clock - MCF set.
2) A match of the calling address with its own specific address in slave mode MAAS set.
3) A loss of bus arbitration - MAL set.
This bit must be cleared by software in the interrupt routine.
MCF - Data Transfer Complete
1 (set)
–
0 (clear) –
A byte transfer has been completed.
A byte is being transfer.
MAAS - Addressed as Slave
1 (set)
–
0 (clear) –
Currently addressed as a slave.
Not currently addressed.
TPG
MC68HC05BD3
RESETS AND INTERRUPTS
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
4-7
37
Freescale Semiconductor, Inc.
Then CPU needs to check the SRW bit and set its MTX bit accordingly. Writing to the M-Bus
Control register clears this bit.
MAL - Arbitration Lost
1 (set)
–
0 (clear) –
Freescale Semiconductor, Inc...
4
Lost arbitration in master mode.
No arbitration lost.
Refer to Section 7 for detailed description of M-Bus Interface.
4.2.2.4
Multi-Function Timer Interrupts
There are two interrupt sources, TOF and RTIF bits of Multi-Function Timer Control and Status
Register. The interrupt service routine address is specified by the contents of memory location
$3FF4 and $3FF5.
Address bit 7
MFT Control and Status Register
$0008
TOF
bit 6
bit 5
bit 4
bit 3
RTIF
TOFIE
RTIE
IRQN
bit 2
bit 1
bit 0
State
on reset
RT1
RT0
0000 0011
TOF - Timer Overflow
1 (set)
–
0 (clear) –
8-bit ripple timer overflow has occurred.
No 8-bit ripple timer overflow has occurred.
This bit is set when the 8-bit ripple counter overflows from $FF to $00; a timer overflow interrupt
will occur, if TOFIE is set. TOF is cleared by writing a “0” to the bit.
RTIF - Real Time Interrupt Flag
1 (set)
–
0 (clear) –
A real time interrupt has occurred.
A real time interrupt has not occurred.
The clock frequency that drives the RTI circuit is E/16384, giving a maximum interrupt period of
8.19ms at a bus clock rate of 2MHz. A CPU interrupt request will be generated if RTIE is set. RTIF
is cleared by writing a “0” to the bit.
Refer to Section 5 for detailed description of Multi-Function Timer.
TPG
MOTOROLA
4-8
RESETS AND INTERRUPTS
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
38
Freescale Semiconductor, Inc.
5
Freescale Semiconductor, Inc...
MULTI-FUNCTION TIMER
The MFT provides miscellaneous functions to the MC68HC05BD3 MCU. It includes a timer
overflow function, real-time interrupt, and COP watchdog. The external interrupt (IRQ) triggering
option is also set by this module’s MFT Control and Status Register.
5
The clock base for this module is derived from the bus clock divided by four. For a 2MHz E (CPU)
clock, the clock base is 0.5MHz. This clock base is then divided by an 8-stage ripple counter to
generate the timer overflow. Timer overflow rate is thus E/1024. The output of this 8-stage ripple
counter then drives a 4-stage divider to generate real time interrupt. Hence, the clock base for real
time interrupt is E/16384. Real time interrupt rate is selected by RT0 and RT1 bits of MFT Control
and Status register. The interrupt rates are E/16384, (E/16384)/2, (E/16384)/4, and (E/16384)/8.
The selected real time interrupt rate is then divided by 8 to generate COP reset.
5.1
MFT Counter Register
The MFT counter register (MFTCR) can be read at location $0009. It is cleared by reset.
5.2
MFT Control and Status Register
Address bit 7
MFT Control and Status Register
$1C
TOF
bit 6
bit 5
bit 4
bit 3
RTIF
TOFIE
RTIE
IRQN
bit 2
bit 1
bit 0
State
on reset
RT1
RT0
0000 0011
Register bit definitions:
TOF - Timer Overflow
1 (set)
–
0 (clear) –
8-bit ripple timer overflow has occurred.
No 8-bit ripple timer overflow has occurred.
TPG
MC68HC05BD3
MULTI-FUNCTION TIMER
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
5-1
39
Freescale Semiconductor, Inc.
This bit is set when the 8-bit ripple counter overflows from $FF to $00; a timer overflow interrupt
will occur, if TOFIE (bit 5) is set. TOF is cleared by writing a “0” to the bit.
RTIF - Real Time Interrupt Flag
1 (set)
–
Freescale Semiconductor, Inc...
0 (clear) –
A real time interrupt has occurred.
A real time interrupt has not occurred.
When RTIF is set, a CPU interrupt request is generated if RITE is set. The clock frequency that
drives the RTI circuit is E/16384 giving a maximum interrupt period of 8.19ms at a bus rate of
2MHz. RTIF is cleared by writing a “0” to the bit.
5
TOFIE - Timer Overflow Interrupt Enable
1 (set)
–
TOF interrupt is enabled.
0 (clear) –
TOF interrupt is disabled.
RTIE - Real Time Interrupt Enable
1 (set)
–
Real time interrupt is enabled.
0 (clear) –
Real time interrupt is disabled.
IRQN - IRQ Pin Trigger Option
1 (set)
–
0 (clear) –
Negative edge triggering for IRQ only
Level and negative edge triggering for IRQ
RT1, RT0 - Rate Select for COP watchdog and RTI
See Section 5.3 on watchdog reset.
5.3
COP Watchdog
The COP (Computer Operating Properly) watchdog timer function is implemented by using the
output of the Multi-Function Timer counter. The minimum COP reset rates are controlled by RT0
and RT1 of MFT Control and Status register. If the COP circuit times out, an internal reset is
generated and the reset vector is fetched (at $3FFE & $3FFF). Preventing a COP time-out is
achieved by writing a “0” to bit 0 of address $3FF0. The COP counter has to be cleared periodically
by software with a period less than COP reset rate. The COP watchdog timer is always enabled
and continues to count in Wait mode.
TPG
MOTOROLA
5-2
MULTI-FUNCTION TIMER
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
40
Freescale Semiconductor, Inc.
Table 5-1 COP Reset and RTI Rates
RT1
RT0
0
0
1
1
0
1
0
1
Freescale Semiconductor, Inc...
Note:
Minimum COP reset period
COP
E clock = 2MHz
E/16384/7/1
57.344ms
E/16384/7/2
114.688ms
E/16384/7/4
229.376ms
E/16384/7/8
458.752ms
RTI period
RTI
E clock = 2MHz
E/16384/1
8.192ms
E/16384/2
16.384ms
E/16384/4
32.768ms
E/16384/8
65.536ms
RT0 and RT1 should only be changed immediately after COP
watchdog timer has been reset.
5
TPG
MC68HC05BD3
MULTI-FUNCTION TIMER
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
5-3
41
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
5
THIS PAGE LEFT BLANK INTENTIONALLY
TPG
MOTOROLA
5-4
MULTI-FUNCTION TIMER
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
42
Freescale Semiconductor, Inc.
6
Freescale Semiconductor, Inc...
PULSE WIDTH MODULATION
The MC68HC05BD3 has 16 PWM channels. Channel 0 to 7 are dedicated PWM channels.
Channel 8 to 15 are shared with port C I/O pins, and are selected by the respective bits in
Configuration register 1. PWM channels 0 to 13 are +10V open-drain type; therefore a pull-up
resistor is required at each of the pins.
6
6.1
PWM Registers
Each PWM channel has an 8-bit register which contains a 5-bit PWM in the MSB portion and a
3-bit binary rate multiplier (BRM) in the LSB portion. The PWM channel data registers are located
from $20 to $2F.
bit 2
bit 1
bit 0
State
on reset
0BRM2
0BRM1
0BRM0
0000 0000
$002F 15PWM4 15PWM3 15PWM2 15PWM1 15PWM0 15BRM2 15BRM1 15BRM0
0000 0000
Address
0PWM
$0020
bit 7
bit 6
bit 4
bit 3
0PWM4 0PWM3 0PWM2 0PWM1 0PWM0
:
:
15PWM
6.2
bit 5
General Operation
The value programmed in the 5-bit PWM portion will determine the pulse length of the output. The
clock to the 5-bit PWM portion is the E clock and the repetition rate of the output is hence 62.5KHz
at 2MHz E clock.
The 3-bit BRM will generate a number of narrow pulses which are equally distributed among an
8-PWM-cycle. The number of pulses generated is equal to the number programmed in the 3-bit
BRM portion. Example of the waveforms are shown in Figure 6-1.
Combining the 5-bit PWM together with the 3-bit BRM, the average duty cycle at the output will be
(M+N/8)/32, where M is the content of the 5-bit PWM portion, and N is the content of the 3-bit BRM
portion. Using this mechanism, a true 8-bit resolution PWM is achieved.
TPG
MC68HC05BD3
PULSE WIDTH MODULATION
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
6-1
43
Freescale Semiconductor, Inc.
The value of each PWM Data Register is continuously compared with the content of an internal
counter to determine the state of each PWM channel output pin. Double buffering is not used in
this PWM design.
32T=16µs
Freescale Semiconductor, Inc...
M=$00
T
M=$01
6
31T
16T
M=$0F
16T
31T
M=$1F
Pulse inserted at end of PWM cycle
depends on setting of N.
T
T=1 CPU clock period (0.5µs if CPU clock=2MHz)
M = value set in 5-bit PWM (bit3-bit7)
N = value set in 3-bit BRM (bit0-bit2)
N
xx1
x1x
1xx
PWM cycles where pulses are inserted in a 8-cycle frame
4
2, 6
1, 3, 5, 7
Number of inserted
pulses in a 8-cycle frame
1
2
4
Figure 6-1 8-Bit PWM Output Waveforms
TPG
MOTOROLA
6-2
PULSE WIDTH MODULATION
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
44
Freescale Semiconductor, Inc.
7
Freescale Semiconductor, Inc...
M-BUS SERIAL INTERFACE
M-Bus (Motorola Bus) is a two-wire, bidirectional serial bus which provides a simple, efficient way
for data exchange between devices. It is fully compatible with the I2C bus standard. This two-wire
bus minimizes the interconnection between devices and eliminates the need for address
decoders; resulting in less PCB traces and economic hardware structure. This bus is suitable for
applications requiring communications in a short distance among a number of devices. The
maximum data rate is 100Kbit/s. The maximum communication length and number of devices that
can be connected are limited by a maximum bus capacitance of 400pF.
The M-Bus system is a true multi-master bus, including arbitration to prevent data collision if two
or more masters intend to control the bus simultaneously. It may be used for rapid testing and
alignment of end products via external connections to an assembly-line computer.
7.1
7
M-Bus Interface Features
•
Compatible with I2C bus standard
•
Multi-master operation
•
32 software programmable serial clock frequencies
•
Software selectable acknowledge bit
•
Interrupt driven byte-by-byte data transfer
•
Arbitration lost driven interrupt with automatic mode switching from master to slave
•
Calling address identification interrupt
•
Generate/detect the start, stop and acknowledge signals
•
Repeated START signal generation
•
Bus busy detection
TPG
MC68HC05BD3
M-BUS SERIAL INTERFACE
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
7-1
45
Freescale Semiconductor, Inc.
Internal bus
8
Control register
Status register
MEN MIEN MSTA MTX TXAK
MAL
SRW
MIF
RXAK
Frequency
divider
register
Address
register
M-Bus
interrupt
Interrupt
Freescale Semiconductor, Inc...
MCF MAAS MBB
Address
comparator
M-Bus clock
generator
sync logic
SCL
control
SCL
START, STOP
detector and
arbitration
7
START, STOP
generator and
timing sync
TX shift
register
RX shift
register
TX
control
RX
control
SDA
control
SDA
Figure 7-1 M-Bus Interface Block Diagram
7.2
M-Bus Protocol
Normally, a standard communication is composed of four parts,
1) START signal,
2) slave address transmission,
3) data transfer, and
4) STOP signal.
They are described briefly in the following sections and illustrated in Figure 7-2.
TPG
MOTOROLA
7-2
M-BUS SERIAL INTERFACE
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
46
Freescale Semiconductor, Inc.
MSB
SCL
1
1
0
0
0
0
1
LSB
MSB
1
1
LSB
1
0
0
0
0
1
Acknowledge bit
1
No acknowledge
SDA
Freescale Semiconductor, Inc...
START signal
STOP signal
MSB
SCL
1
1
0
0
0
0
1
LSB
MSB
1
1
LSB
1
0
0
0
Acknowledge bit
0
1
1
No acknowledge
SDA
START signal
repeated START signal
STOP signal
7
Figure 7-2 M-Bus Transmission Signal Diagram
7.2.1
START Signal
When the bus is free, i.e., no master device is occupying the bus (both SCL and SDA lines are at
logic high), a master may initiate communication by sending a START signal. As shown in
Figure 7-2, a START signal is defined as a high to low transition of SDA while SCL is high. This
signal denotes the beginning of a new data transfer (each data transfer may contain several bytes
of data) and wakes up all slaves.
7.2.2
Slave Address Transmission
The first byte of data transfer immediately following the START signal is the slave address
transmitted by the master. This is a seven bits long calling address followed by a R/W bit. The R/W
bit dictates the slave of the desired direction of data transfer.
Only the slave with matched address will respond by sending back an acknowledge bit by pulling
the SDA low at the 9th clock; see Figure 7-2.
TPG
MC68HC05BD3
M-BUS SERIAL INTERFACE
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
7-3
47
Freescale Semiconductor, Inc.
7.2.3
Data Transfer
Once a successful slave addressing is achieved, the data transfer can proceed byte by byte in a
direction specified by the R/W bit sent by the calling master.
Freescale Semiconductor, Inc...
Each data byte is 8 bits long. Data can be changed only when SCL is low and must be held stable
when SCL is high as shown in Figure 7-2. One clock pulse is for one bit of data transfer, MSB is
transferred first. Each data byte has to be followed by an acknowledge bit. Hence, one complete
data byte transfer requires 9 clock pulses.
If the slave receiver does not acknowledge the master, the SDA line should be left high by the
slave, the master can then generate a STOP signal to abort the data transfer or a START signal
(repeated START) to commence a new calling.
If the master receiver does not acknowledge the slave transmitter after one byte transmission, it
means an “end of data” to the slave. The slave shall release the SDA line for the master to
generate STOP or START signal.
7
7.2.4
Repeated START Signal
As shown in Figure 7-2, a repeated START signal is to generate a START signal without first
generating a STOP signal to terminate the communication. This is used by the master to
communicate with another slave or with the same slave in a different mode (transmit/receive
mode) without releasing the bus.
7.2.5
STOP Signal
The master can terminate the communication by generating a STOP signal to free the bus.
However, the master may generate a START signal followed by a calling command without
generating a STOP signal first. This is called repeat START. A STOP signal is defined as a low to
high transition of SDA while SCL is at a logical high; see Figure 7-2.
7.2.6
Arbitration Procedure
This interface circuit is a true multi-master system which allows more than one master to be
connected. If two or more masters try to control the bus at the same time, a clock synchronization
procedure determines the bus clock. The clock low period is equal to the longest clock low period
among the masters; and the clock high period is the shortest among the masters. A data
arbitration procedure determines the priority. A master will lose arbitration if it transmits a logic “1”
while the others transmit logic “0”, the losing master will immediately switch over to slave receive
mode and stops its data and clock outputs. The transition from master to slave mode will not
generate a STOP condition. Meanwhile, a software bit will be set by hardware to indicate loss of
arbitration.
TPG
MOTOROLA
7-4
M-BUS SERIAL INTERFACE
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
48
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
7.2.7
Clock Synchronization
Since wire-AND logic is performed on the SCL line, a high to low transition on SCL line will affect
the devices connected to the bus. The devices start counting their low period and once a device's
clock has gone low, it will hold the SCL line low until the clock high state is reached. However, the
change of low to high in this device clock may not change the state of the SCL line, if another
device clock is still in its low period. Therefore synchronized clock SCL will be held low by the
device which releases SCL to a logic high in the last place. Devices with shorter low periods enter
a high wait state during this time (see Figure 7-3). When all devices concerned have counted off
their low period, the synchronized clock SCL line will be released and go high. All of them will start
counting their high periods. The first device to complete its high period will again pull the SCL line
low.
WAIT
Start counting high period
SCL1
7
SCL2
SCL
Internal counter reset
Figure 7-3 Clock Synchronization
7.2.8
Handshaking
The clock synchronization mechanism can be used as a handshake in data transfer. Slave device
may hold the SCL low after completion of one byte transfer (9 bits). In such case, it will halt the
bus clock and force the master clock in a wait state until the slave releases the SCL line.
7.3
M-Bus Registers
There are five registers used in the M-Bus interface, these are discussed in the following
paragraphs.
TPG
MC68HC05BD3
M-BUS SERIAL INTERFACE
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
7-5
49
Freescale Semiconductor, Inc.
7.3.1
M-Bus Address Register (MADR)
Address
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
$0017
MAD7
MAD6
MAD5
MAD4
MAD3
MAD2
MAD1
bit 0
State
on reset
0000 0000
Freescale Semiconductor, Inc...
MAD1-MAD7 are the slave address bits of the M-Bus module.
7.3.2
M-Bus Frequency Register (MFDR)
Address
bit 7
bit 6
bit 5
$0018
bit 4
bit 3
bit 2
bit 1
bit 0
State
on reset
FD4
FD3
FD2
FD1
FD0
0000 0000
FD0-FD4 are used for clock rate selection. The serial bit clock frequency is equal to the CPU clock
divided by the divider shown in Table 7-1.
7
Table 7-1 M-Bus Prescaler
FD4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
FD3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
FD2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
FD1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
FD0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
DIVIDER
22
24
28
34
44
48
56
68
88
96
112
136
176
192
224
272
FD4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
FD3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
FD2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
FD1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
FD0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
DIVIDER
352
384
448
544
704
768
896
1088
1408
1536
1792
2176
2816
3072
3584
4352
For a 4MHz external crystal operation (2MHz internal operating frequency), the serial bit clock
frequency of M-Bus ranges from 460Hz to 90,909Hz.
TPG
MOTOROLA
7-6
M-BUS SERIAL INTERFACE
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
50
Freescale Semiconductor, Inc.
7.3.3
M-Bus Control Register (MCR)
Address
bit 7
bit 6
bit 5
bit 4
bit 3
$0019
MEN
MIEN
MSTA
MTX
TXAK
bit 2
bit 1
bit 0
State
on reset
0000 0000
Register bit definitions:
Freescale Semiconductor, Inc...
MEN - M-Bus Enable
1 (set)
–
M-Bus interface system enabled.
0 (clear) –
M-Bus interface system disabled.
MIEN - M-Bus Interrupt Enable
1 (set)
–
M-Bus interrupt enabled.
0 (clear) –
M-Bus interrupt disabled.
This bit enables the MIF (in MSR) for M-Bus interrupts.
7
MSTA - Master/Slave Select
1 (set)
–
0 (clear) –
M-Bus is set for master mode operation.
M-Bus is set for slave mode operation.
Upon reset, this bit is cleared. When this bit is changed from 0 to 1, a START signal is generated
on the bus, and the master mode is selected. When this bit is changed from 1 to 0, a STOP signal
is generated and the operation mode changes from master to slave. In master mode, a bit clear
immediately followed by a bit set of this bit generates a repeated START signal without generating
a STOP signal.
MTX - Transmit/Receive Mode Select
1 (set)
–
0 (clear) –
M-Bus is set for transmit mode.
M-Bus is set for receive mode.
TXAK - Acknowledge Enable
1 (set)
–
0 (clear) –
Do not send acknowledge signal.
Send acknowledge signal at 9th clock bit.
If cleared, an acknowledge signal will be sent out to the bus at the 9th clock bit after receiving one
byte of data. If set, no acknowledge signal response. This is an active low control bit.
TPG
MC68HC05BD3
M-BUS SERIAL INTERFACE
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
7-7
51
Freescale Semiconductor, Inc.
7.3.4
M-Bus Status Register (MSR)
Address
bit 7
bit 6
bit 5
bit 4
$001A
MCF
MAAS
MBB
MAL
bit 3
bit 2
bit 1
bit 0
State
on reset
SRW
MIF
RXAK
1000 0001
The MIF and MAL bits are software clearable; while the other bits are read only.
Freescale Semiconductor, Inc...
MCF - Data Transfer Complete
1 (set)
–
0 (clear) –
A byte transfer has been completed.
A byte is being transfer.
When MCF is set, the MIF (M-Bus interrupt) bit is also set. An M-Bus interrupt is generated if the
MIEN bit is set.
MAAS - Addressed as Slave
1 (set)
7
–
0 (clear) –
Currently addressed as a slave.
Not currently addressed.
This MAAS bit is set when its own specific address (M-Bus Address register) matches the calling
address. When MAAS is set, the MIF (M-Bus interrupt) bit is also set. An interrupt is generated if
the MIEN bit is set. Then CPU needs to check the SRW bit and set its MTX bit accordingly. Writing
to the M-Bus Control register clears this bit.
MBB - Bus Busy
1 (set)
–
0 (clear) –
M-Bus busy.
M-Bus idle.
This bit indicates the status of the bus. When a START signal is detected, MBB is set. When a
STOP signal is detected, it is cleared.
MAL - Arbitration Lost
1 (set)
–
0 (clear) –
Lost arbitration in master mode.
No arbitration lost.
This arbitration lost flag is set when the M-Bus master loses arbitration during a master
transmission mode. When MAL is set, the MIF (M-Bus interrupt) bit is also set. This bit must be
cleared by software.
TPG
MOTOROLA
7-8
M-BUS SERIAL INTERFACE
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
52
Freescale Semiconductor, Inc.
SRW - Slave R/W Select
1 (set)
–
0 (clear) –
Read from slave, from calling master
Write to slave from calling master.
When MAAS is set, the R/W command bit of the calling address sent from the master is latched
into this SRW bit. By checking this bit, the CPU can then select slave transmit/receive mode by
configuring MTX bit of the M-Bus Control register.
Freescale Semiconductor, Inc...
MIF - M-Bus Interrupt
1 (set)
–
0 (clear) –
An M-Bus interrupt has occurred.
An M-Bus interrupt has not occurred.
When this bit is set, an interrupt is generated to the CPU if MIEN is set. This bit is set when one
of the following events occurs:
1) Completion of one byte of data transfer. It is set at the falling edge of the 9th
clock - MCF set.
2) A match of the calling address with its own specific address in slave mode MAAS set.
7
3) A loss of bus arbitration - MAL set.
This bit must be cleared by software in the interrupt routine.
RXAK - Receive Acknowledge
1 (set)
–
0 (clear) –
No acknowledgment signal detected.
Acknowledgment signal detected after 8 bits data transmitted.
If cleared, it indicates an acknowledge signal has been received after the completion of 8 bits data
transmission on the bus. If set, no acknowledge signal has been detected at the 9th clock. This is
an active low status flag.
7.3.5
M-Bus Data I/O Register (MDR)
Address
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
State
on reset
$001B
MD7
MD6
MD5
MD4
MD3
MD2
MD1
MD0
uuuu uuuu
In master transmit mode, data written into this register is sent to the bus automatically, with the
most significant bit out first. In master receive mode, reading of this register initiates receiving of
the next byte data. In slave mode, the same function applies after it has been addressed.
TPG
MC68HC05BD3
M-BUS SERIAL INTERFACE
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
7-9
53
Freescale Semiconductor, Inc.
Clear MIF
Y
Freescale Semiconductor, Inc...
TX
Last byte
transmitted?
TX/RX?
Y
N
RX
N
Last byte to
be read?
N
Master Mode?
Arbitration
Lost?
Y
Y
Clear MAL
Generate
STOP
signal
N
MAAS=1?
Y
N
7
RXAK=0?
N
Last 2nd
byte to read?
Y
N
MAAS=1?
RX
Y
ACK from
receiver?
Y
Generate
STOP
signal
Y
TX
TXAK=1
Write to MDR
TX/RX?
Read from MDR
Write to MDR
N
N
SRW=1?
N
Y
Set RX mode
Set TX mode
Dummy read MDR
Write to MDR
RTI
Figure 7-4 Flowchart of M-Bus Interrupt Routine
TPG
MOTOROLA
7-10
M-BUS SERIAL INTERFACE
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
54
Freescale Semiconductor, Inc.
7.4
Programming Considerations
7.4.1
Initialization
Reset will put the M-Bus Control register to its default status. Before the interface can be used to
transfer serial data, the following initialization procedure must be carried out.
1) Update Frequency Divider Register (MFDR) to select an SCL frequency.
Freescale Semiconductor, Inc...
2) Update M-Bus Address Register (MADR) to define its own slave address.
3) Set MEN bit of M-Bus Control Register (MCR) to enable the M-Bus interface
system.
4) Modify the bits of M-Bus Control Register (MCR) to select Master/Slave
mode, Transmit/Receive mode, interrupt enable or not.
7.4.2
Generation of a START Signal and
the First Byte of Data Transfer
After completion of the initialization procedure, serial data can be transmitted by selecting the
master transmit mode. If the device is connected to a multi-master bus system, the state of the
M-Bus busy bit (MBB) must be tested to check if the serial bus is free. If the bus is free (MBB=0),
the START condition and the first byte (the slave address) can be sent. An example program which
generates the START signal and transmits the first data byte (slave address) is shown below:
SEI
BRSET
CHFLAG
TXSTART
BSET
BSET
LDA
STA
CLI
7.4.3
;
5,MSR,CHFLAG ;
;
;
4,MCR
;
5,MCR
;
;
#CALLING
;
MDR
;
;
;
7
DISABLE INTERRUPT
CHECK THE MBB BIT OF THE
STATUS REGISTER. IF IT IS
SET, WAIT UNTIL IT IS CLEAR
SET TRANSMIT MODE
SET MASTER MODE
i.e. GENERATE START CONDITION
GET THE CALLING ADDRESS
TRANSMIT THE CALLING
ADDRESS
ENABLE INTERRUPT
Software Responses after Transmission or
Reception of a Byte
Upon the completion of the transmission or reception of a data byte, the data transferring bit (MCF)
will be set, indicating one byte communication has been finished. The M-Bus interrupt bit (MIF)
will also be set to generate an M-Bus interrupt if the interrupt is enabled. Software must clear the
TPG
MC68HC05BD3
M-BUS SERIAL INTERFACE
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
7-11
55
Freescale Semiconductor, Inc.
MIF bit in the interrupt routine first. The MCF bit can be cleared by reading the M-Bus Data I/O
Register (MDR) in receive mode or writing to the MDR in transmit mode. Software may serve the
M-Bus I/O in the main program by monitoring the MIF bit if the interrupt is disabled. The following
is an example of a software response by a master in transmit mode in the interrupt routine (see
Figure 7-4).
ISR
BCLR
BRCLR
1,MSR
5,MCR,SLAVE
;
;
;
4,MCR,RECEIVE ;
;
0,MSR,END
;
;
;
DATABUF
;
MDR
;
Freescale Semiconductor, Inc...
BRCLR
BRSET
TRANSMIT
7.4.4
7
LDA
STA
CLEAR THE MIF FLAG
CHECK THE MSTA FLAG,
BRANCH IF SLAVE MODE
CHECK THE MODE FLAG,
BRANCH IF IN RECEIVE MODE
CHECK ACK FROM RECEIVER
IF NO ACK, END OF
TRANSMISSION
GET THE NEXT BYTE OF DATA
TRANSMIT THE DATA
Generation of the STOP Signal
A data transfer ends with a STOP signal generated by the master device. A master in transmit
mode can simply generate a STOP signal after all the data have been transmitted. The following
is an example showing how a STOP condition is generated by a master in transmit mode.
MASTX
BRSET 0,MSR,END
LDA
TXCNT
BEQ
LDA
STA
DEC
BRA
END
BCLR
EMASTX RTI
END
DATABUF
MDR
TXCNT
EMASTX
5,MCR
;
;
;
;
;
;
;
;
;
;
;
IF NO ACK, BRANCH TO END
GET VALUE FROM THE
TRANSMITTING COUNTER
IF NO MORE DATA, BRANCH TO
END
GET NEXT BYTE OF DATA
TRANSMIT THE DATA
DECREASE THE TXCNT
EXIT
GENERATE A STOP CONDITION
RETURN FROM INTERRUPT
If a master receiver wants to terminate a data transfer, it must inform the slave transmitter by not
acknowledging the last byte of data. This can be achieved by setting the transmit acknowledge bit
(TXAK) before reading the 2nd last byte of data. Before reading the last byte of data, a STOP
signal must be generated first. The following is an example showing how a STOP signal is
generated by a master in receive mode.
MASR
DEC
BEQ
LDA
DECA
BNE
RXCNT
ENMASR
RXCNT
NXMAR
; LAST BYTE TO BE READ
; CHECK LAST 2ND BYTE TO BE READ
; NOT LAST ONE OR LAST SECOND
TPG
MOTOROLA
7-12
M-BUS SERIAL INTERFACE
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
56
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
LAMAR
BSET
3,MCR
BRA
ENMASR BCLR
NXMAR
5,MCR
NXMAR
MDR
RXBUF
LDA
STA
RTI
7.4.5
; LAST SECOND, DISABLE ACK
; TRANSMITTING
; LAST ONE, GENERATE 'STOP'
; SIGNAL
; READ DATA AND STORE
Generation of a Repeated START Signal
At the end of data transfer, if the master still wants to communicate on the bus, it can generate
another START signal followed by another slave address without first generating a STOP signal.
A program example is as shown.
RESTART
7.4.6
BCLR
BSET
5,MCR
5,MCR
LDA
STA
#CALLING
MDR
;
;
;
;
;
;
ANOTHER START (RESTART) IS
GENERATED BY THESE TWO
CONSECUTIVE INSTRUCTIONS
GET THE CALLING ADDRESS
TRANSMIT THE CALLING
ADDRESS
7
Slave Mode
In the slave service routine, the master addressed as slave bit (MAAS) should be tested to check
if a calling of its own address has been received (Figure 7-4). If MAAS is set, software should set
the transmit/receive mode select bit (MTX bit of MCR) according to the R/W command bit (SRW).
Writing to the MCR clears the MAAS automatically. A data transfer may then be initiated by writing
to MDR or a dummy read from MDR.
In the slave transmit routine, the received acknowledge bit (RXAK) must be tested before
transmitting the next byte of data. RXAK, if set indicates the end of data signal from the master
receiver, the slave transmitter must then switch from transmit mode to receive mode by software
and a dummy read must follow to release the SCL line so that the master can generate a STOP
signal.
7.4.7
Arbitration Lost
If more than one master want to acquire the bus simultaneously, only one master can win and the
others will lose arbitration. The losing device immediately switches to slave receive mode by
M-Bus hardware. Its data output to the SDA line is stopped, but internal transmit clock still runs
until the end of the data byte transmission. An interrupt occurs when this dummy byte transmission
TPG
MC68HC05BD3
M-BUS SERIAL INTERFACE
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
7-13
57
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
is accomplished with MAL=1 and MSTA=0. If one master attempts to start transmission while the
bus is being controlled by another master, the transmission will be inhibited; the MSTA bit will be
changed from 1 to 0 without generating STOP condition; an interrupt will be generated and the
MAL bit set to indicate that the attempt to acquire the bus has failed. Considering these cases, the
slave service routine should test the MAL bit first, and software should clear the MAL bit if it is set.
7
TPG
MOTOROLA
7-14
M-BUS SERIAL INTERFACE
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
58
Freescale Semiconductor, Inc.
8
Freescale Semiconductor, Inc...
SYNC SIGNAL PROCESSOR
The functions of the SSP include polarity correction, sync separation, sync pulse reshaper, sync
pulse detectors, horizontal line counter, vertical frequency counter, and free running signals
generator. In addition, interrupt can be generated for each vertical frame at a user specified
horizontal line number.
The processor accepts either composite or separate sync inputs.
For separate sync inputs, the HTTL and VTTL outputs are identical to the incoming horizontal sync
with negative sync polarity. As for composite sync input, reassembled horizontal sync pulses can
be inserted during the vertical sync period. The VTTL output is triggered by the leading edge of
the incoming vertical sync pulse, and the sync pulse will be widened by 9.5µs.
Both HSYNC and VSYNC inputs have internal filter to improve noise immunity. Any pulse that is
shorter than an internal bus clock period, will be regarded as a glitch, and will be ignored.
Note:
8.1
8
All quoted timings in this section are based on the assumption that the internal bus
frequency is 2MHz, i.e. tCYC =0.5µs.
Functional Blocks
The architecture of the Sync Signal Processor is shown in Figure 8-1. Each of the functional
blocks are described in the following paragraphs.
8.1.1
Polarity Correction
The polarity correction block of the sync signal processor accepts the input sync signals
(HSYNC/VSYNC) and converts them to negative polarity signals, regardless of the polarity of the
inputs. The following describes the methodologies used in polarity correction.
TPG
MC68HC05BD3
SYNC SIGNAL PROCESSOR
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
8-1
59
Freescale Semiconductor, Inc.
VSIN
FOUT
V FREQ.
REGISTER
$0D
$0E
Freescale Semiconductor, Inc...
VSYNC
COUNTER
VSYNC
POLARITY
CORRECTOR
MUX
HSYNC
SYNC
DETECTOR
VDET
VSYNC
RESHAPER
VFREE
COMPOSITE
POLARITY
CORRECTOR
VTTL
MUX
R
S
CLK GEN.
HFREE
SYNC
SEPARATOR
& INSERTION
$11
8
SYNC SIGNAL
CONTROL REG.
SOUT
R
V
MUX
HTTL
H
INTERRUPT
CIRCUIT
HSYNC
COUNTER
INTERRUPT
LINE FREQ.
REGISTERS
SYNC
DETECTOR
HDET
$0F
$10
Figure 8-1 Sync Signal Processor Block Diagram
8.1.1.1
Separate Vertical Sync Input
To test the polarity of the input sync signal, the duration of the low pulse is examined. If the low
period is longer than a specific value (512µs or 1024tCYC), as in the case of positive polarity input
sync, the input sync will be inverted before output. For negative polarity input sync signal, it is
anticipated that the duration of the low pulse would be shorter than the specific value, and the input
sync signal passes through to the output without inversion.
This polarity correction is a continuous process, and the error margin is equal to the maximum
permissible sync pulse width specified (512µs or 1024tCYC). At power-up or system reset,
negative polarity at input is assumed.
TPG
MOTOROLA
8-2
SYNC SIGNAL PROCESSOR
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
60
Freescale Semiconductor, Inc.
Positive polarity pure horizontal sync signal
Freescale Semiconductor, Inc...
Negative polarity pure horizontal sync signal
Positive polarity composite sync signal
Negative polarity composite sync signal
Figure 8-2 Sync Signal Polarity Correction
8.1.1.2
Separate Horizontal Or Composite Sync Input
Since the input at HSYNC can be either a pure horizontal sync signal or a composite sync signal,
different methodologies are used in polarity correction.
8
Unlike the polarity correction for VSYNC, both the high pulse and low pulse of the sync signal at
HSYNC are examined. If the pulse, either active high or low, is longer than a certain period (8µs
or 16 tCYC), it will be regarded as a long pulse. If there are 8 consecutive low long pulses, the input
sync signal will be confirmed as a positive polarity sync signal, and will be inverted. If there are 8
consecutive high long pulses, it will be confirmed as a negative polarity sync signal.
The operation of this module is also continuous, and the error margin is equal to the period of the
pre-set number (default is 8) of horizontal sync pulses. At power-up or system reset, negative
polarity at input is assumed.
8.1.2
Sync Detection
The sync detector determines whether the incoming sync signal is active. Both sync high and low
pulse widths must be within the specific values to be regarded as active. HDET and VDET flags
will be set if the HSYNC and VSYNC signals are active, respectively.
TPG
MC68HC05BD3
SYNC SIGNAL PROCESSOR
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
8-3
61
Freescale Semiconductor, Inc.
8.1.3
Free-running Pseudo Sync Signal Generator
Freescale Semiconductor, Inc...
If either HSYNC or VSYNC is absent, a free-running sync signal generator will be enabled. It
generates a pseudo vertical sync at 63.5Hz (1/(tcyc x 31488)) and a pseudo horizontal sync at
either 48.8KHz (1/(tCYC x 41)) or 62.5KHz (1/(tCYC x 32)), depending on the status of FOUT. This
set of free running sync signals replaces the inactive sync signals at the inputs and will be fed to
the VTTL and HTTL pins if the pins are selected for VTTL and HTTL function.
8.1.4
Sync Separation
Figure 8-3 is a block diagram of the Sync Separator which includes the duration counters for the
high and low pulses, a counter for the number of valid horizontal sync pulses, a register to hold
the number of horizontal lines per frame, a logic block for horizontal and vertical sync pulse
separation, a comparator, and a sync pulse insertion circuit.
CLK
HSYNC
(After polarity correction)
load
Horizontal Sync Register
in
Horizontal sync pulse counter
8
reset
out
count
Low pulse duration counter
Comparator
equal
High pulse duration counter
finish
Sync separation logic
Sync insertion circuit
Hsync
Vsync
Figure 8-3 Sync Separator
The Low pulse duration counter examines the low pulse width of the incoming composite sync
signal. If it is within the horizontal sync pulse limit (8µs or 16 tCYC), a horizontal sync pulse is
detected and the horizontal sync pulse counter is advanced. If the low pulse is wider than the limit,
TPG
MOTOROLA
8-4
SYNC SIGNAL PROCESSOR
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
62
Freescale Semiconductor, Inc.
a vertical sync pulse is detected, and the content of the Horizontal sync pulse counter is loaded
into the Horizontal Sync Register before the Low Pulse Duration Counter is reset.
Comparator compares the values of the Horizontal Sync Pulse Counter and Horizontal Sync
Register, and gives the equal signal to the Sync Separation Logic.
Freescale Semiconductor, Inc...
High Pulse Duration Counter examines the high pulse width of the incoming composite sync
signal. If it is longer than a specific value (8µs or 16 tCYC), the vertical sync pulse has finished and
finish signal will be given to the Sync Separation Logic.
Sync Separation Logic passes the composite sync signal to the Hsync output, until there is an
“equal” signal from the comparator. The Hsync output will then output a reassembled waveform
by the Sync Insertion Circuit to emulate the HSYNC pulses, and the Vsync output is set to low at
the coming falling edge of the composite signal. After the finish signal has been sensed, the Vsync
output is fixed to high, and the Hsync output follows the composite sync input again.
8.1.5
Vertical Sync Pulse Reshaper
For separate sync inputs, the vertical sync pulse width VTTL equals to the incoming vertical sync
input. For composite sync input, the Sync Pulse Reshaper widens the VTTL pulse width by 9.5µs.
8.1.6
Sync Signal Counters
8
There are two counters (horizontal line counter and vertical frequency counter) to count the
number of horizontal sync pulses and the number of system clock cycles between two vertical
sync pulses. These two data can be read by the CPU to check the signal frequencies and can be
used to determine the video mode. Figure 8-4 shows a more detailed block diagram of these
counters. The 13-bit vertical frequency register encompasses vertical frequency range from
approximately 15Hz to 125KHz. Figure 8-5 shows the vertical frequency counter timing. It
indicates that there will be ±1 count error on the reading from the register for the same vertical
frequency.
8.2
VSYNC Interrupt
The Sync Signal Processor will generate interrupts to the CPU if the VSYNC Interrupt Enable
(VSIE) bit is set, and the I-bit in the Condition Code Register (CCR) is cleared. The interrupt will
occur at each leading edge of VSYNC.
The interrupt vector address is at $3FF8-$3FF9, and the interrupt latch is cleared automatically
by fetching of the interrupt vectors.
TPG
MC68HC05BD3
SYNC SIGNAL PROCESSOR
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
8-5
63
Freescale Semiconductor, Inc.
$0D
$0E
13-bit Vertical Frequency Register
÷16
System Clock
13-bit counter
Freescale Semiconductor, Inc...
R
Negative edge detector
VSYNC
R
HSYNC
Negative edge detector
12-bit counter
$0F
$10
12-bit Horizontal Line Count Register
Figure 8-4 Sync Signal Counters Block Diagram
8
PH2
VSYNIN
Counter signal reset
Counter resets at 4 PH2 cycles
after falling edge of VSYNIN
PH2 ÷16
case1
PH2 ÷16
case2
Counter advances at the
rising edge of the clock
1. The value of the counter will be loaded into the register before it is reset.
2. The Vertical Frequency Counter is clocked by a PH2 ÷16 clock.
3. Because of the asynchronous nature between PH2 and VSYNIN, the register
will have one more count in case 2 than in case 1.
Figure 8-5 Vertical Frequency Counter Timing
TPG
MOTOROLA
8-6
SYNC SIGNAL PROCESSOR
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
64
Freescale Semiconductor, Inc.
8.3
Registers
There are seven registers associated with the Sync Signal Processor, these are described below.
Freescale Semiconductor, Inc...
8.3.1
Sync Signal Control & Status Register (SSCSR)
Address
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
State
on reset
$000C
VPOL
HPOL
VDET
HDET
SOUT
INSRTB
FOUT
VSIN
0000 0000
VPOL - Vertical Sync Input Polarity
1 (set)
–
0 (clear) –
VSYNC input is positive polarity.
VSYNC input is negative polarity.
Vertical Sync Input Polarity flag indicates the polarity of the incoming signal at the VSYNC input.
HPOL - Horizontal Sync Input Polarity
1 (set)
–
0 (clear) –
HSYNC input is positive polarity.
HSYNC input is negative polarity.
Horizontal Sync Input Polarity flag indicates the polarity of the incoming signal at the HSYNC
input.
8
VDET - Vertical Sync Signal Detect
1 (set)
–
0 (clear) –
An active vertical sync is detected at VSYNC input.
No vertical sync signal at VSYNC input; use internal generated
Vsync for VTTL.
Vertical Sync Signal Detect flag, if set, indicates an active input vertical sync signal has been
detected. If cleared, it indicates there is no active signal, and the VTTL will output the internally
generated Vsync signal. An active vertical sync signal is defined as:
VDET = (VSYNC pulse width < 480µs or 960tCYC)·(VSYNC period < 65.5ms or 131x103tCYC)
HDET - Horizontal Sync Signal Detect
1 (set)
–
0 (clear) –
An active horizontal sync is detected at HSYNC input.
No horizontal sync signal at HSYNC input; use internal generated
Hsync for HTTL.
Horizontal Sync Signal Detect flag, if set, indicates an active input horizontal sync signal has been
detected. If cleared, it indicates there is no active signal, and the HTTL will output the internally
generated Hsync signal. An active horizontal sync signal is defined as:
HDET=(HSYNC pulse width < 8µs or 16tCYC)·(9µs or 18tCYC < HSYNC period < 128µs or 256tCYC)
TPG
MC68HC05BD3
SYNC SIGNAL PROCESSOR
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
8-7
65
Freescale Semiconductor, Inc.
SOUT - Sync Output Select
1 (set)
–
0 (clear) –
Use processed VSYNC and HSYNC inputs for VTTL and HTTL.
Use internally generated sync signals for VTTL and HTTL.
When cleared, the outputs to VTTL and HTTL are the internally generated signals. When set, the
outputs are the processed input signals. This bit can only be set if both VDET and HDET are logic
1’s, and will be cleared automatically if VDET or HDET is not logic “1”. Reset clears this bit.
Freescale Semiconductor, Inc...
INSRTB - Hsync Insertion Bit
1 (set)
–
No inserted pulses. Hsync remains high state during the vertical sync
pulse.
0 (clear) –
For composite sync inputs, emulated sync pulses will be inserted into
the Hsync signal during the vertical sync pulse.
For separate sync inputs, when this Hsync Insertion bit is cleared, sync pulses will continue to be
the Hsync signal during the Vertical Sync Pulse. For composite sync input, when this Hsync
Insertion bit is cleared, emulated sync pulses will be inserted into the Hsync signal during the
Vertical Sync Pulse. In both cases, when this bit is set, there will be no inserted pulses, and the
Hsync signal will be high during the Vertical Sync Pulse. Reset clears this bit.
FOUT - Internal Hsync Frequency Select
8
1 (set)
–
63.5Hz and 62.5KHz for VTTL and HTTL outputs respectively if
internally generated sync signals are selected.
0 (clear) –
63.5Hz and 48.8KHz for VTTL and HTTL outputs respectively if
internally generated sync signals are selected.
This bit selects the frequency of the free running Hsync signal to HTTL pin if SOUT bit is cleared.
When FOUT is set, 63.5Hz and 62.5KHz signals are output to VTTL and HTTL, respectively.
When FOUT is cleared, 63.5Hz and 48.8KHz signals are output instead. Reset clears this bits.
VSIN - Vsync Input Source
This bit selects the source of the input sync signals. Reset clears this bits.
1 (set)
–
0 (clear) –
Separated sync signals through VSYNC and HSYNC inputs.
Composite sync signal through HSYNC input
TPG
MOTOROLA
8-8
SYNC SIGNAL PROCESSOR
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
66
Freescale Semiconductor, Inc.
8.3.2
Vertical Frequency Registers (VFRS)
Freescale Semiconductor, Inc...
Address bit 7
VFHR
$000D
VFLR
$000E
VF7
bit 6
VF6
bit 5
VF5
bit 4
bit 3
bit 2
bit 1
bit 0
State
on reset
VF12
VF11
VF10
VF9
VF8
0000 0000
VF4
VF3
VF2
VF1
VF0
0000 0000
This 13-bit read only register pair contains information of the vertical frame frequency. An internal
counter counts the number of internal clocks between two VSYNC pulses. The counted value will
then be transferred to this register. The data corresponds to the period of one vertical frame. This
register can be read to determine if the frame frequency is valid, and to determine the video mode.
However, the data is not valid if VDET bit is cleared.
The frame frequency is calculated by 1/(VFR±1 x 8µs) or 1/(VFR±1 x 16tCYC).
The table below shows examples for the Vertical Frequency Register, all VFR numbers are in
hexadecimal.
Table 8-1 Vertical Frame Frequencies
VFR
$03C0
$03C1
$03C2
$04E2
$04E3
$04E4
$06F9
$06FA
$06FB
8.3.3
Min. Freq.
130.07
129.94
129.80
99.92
99.84
99.76
69.99
69.95
69.91
Max. Freq.
130.34
130.21
130.07
100.08
100.00
99.92
70.07
70.03
69.99
VFR
$0823
$0824
$0825
$09C4
$09C5
$09C6
$1FFD
$1FFE
$1FFF
Min. Freq.
59.98
59.95
59.92
49.98
49.96
49.94
15.262
15.260
15.258
Max. Freq.
60.04
60.01
59.98
50.02
50.00
49.98
15.266
15.264
15.262
8
Line Frequency Registers (LFRs)
Address bit 7
LFHR
$000F HOVER
LFLR
$0010
LF7
bit 6
bit 5
bit 4
LF6
LF5
LF4
bit 3
bit 2
bit 1
bit 0
State
on reset
LF11
LF10
LF9
LF8
0000 0000
LF3
LF2
LF1
LF0
0000 0000
This 12-bit read only register pair contains the number of horizontal lines in each vertical frame.
An internal line counter counts the horizontal sync pulses between two vertical sync pulses. The
counted value will be transferred to this register pair. HOVER bit will be set if the incoming
horizontal sync pulses between two vertical sync pulses are more than 4096 or there is no vertical
TPG
MC68HC05BD3
SYNC SIGNAL PROCESSOR
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
8-9
67
Freescale Semiconductor, Inc.
sync input. The data can be read to determine if the line frequency is valid and to determine the
video mode. However, the data is not valid if HDET or VDET bit is cleared or HOVER bit is set.
User has to determine whether the incoming signal is separate sync or composite sync. If
composite sync signal is input, the actual number of horizontal lines is the value in LFR plus one;
because the internal line counter that counts the horizontal sync pulses is rising-edge triggering.
If the incoming signal is a composite signal, one horizontal line counting is missed.
Freescale Semiconductor, Inc...
8.3.4
Sync Signal Control Register (SSCR)
Address
bit 7
$0011
VSIE
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
State
on reset
0000 0000
This is a read/write register. Interrupt will be generated at the leading edge of VSYNC if the VSIE
bit is set, I bit in CCR is cleared. The VSYNC interrupt vectors are at $3FF8 and $3FF9, and the
interrupt latch is cleared after the interrupt vectors have been fetched.
VSIE - Vsync Interrupt Enable
This bit enables and disables the Vsync interrupt.
1 (set)
8
–
Vsync interrupt enabled.
0 (clear) –
Vsync interrupt disabled.
8.3.5
Horizontal Sync Period Width Register (HPWR)
Address
$001E
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
HPWR7 HPWR6 HPWR5 HPWR4 HPWR3 HPWR2 HPWR1 HPWR0
State
on reset
0000 0000
This 8-bit read only register contains the period of incoming horizontal sync signal. It is sampled
by tCYC so the horizontal period is equal to HPWR x 0.5µs if tCYC is at 2MHz. As the incoming
horizontal sync signal is asynchronous to the system clock, the SSP is designed so that the
maximum counting error of HPWR is –2. User should use the LFR to calculate the HSYNC
frequency if very accurate frequency detection is needed. If HPWR overflows, the HDET in
SSCSR will be cleared. Therefore the minimum valid HSYNC is 256tCYC, i.e. 7.8125KHz if tCYC
equals to 2MHz.
Note:
It is not guaranteed that the HPWR counting is correct for the first HSYNC period after
the trailing edge of VSYNC.
TPG
MOTOROLA
8-10
SYNC SIGNAL PROCESSOR
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
68
Freescale Semiconductor, Inc.
8.4
System Operation
The incoming signals can be either separate HSYNC and VSYNC or composite sync through
HSYNC input. Polarity correction is performed before the sync signals go any further into the
system. The sync pulse detection block continuously monitors the signals to see if the signals are
active. If the signals are not active, the circuit switches to output the internally generated sync
signals. This will protect the circuits behind from being damaged by inactive signals.
Freescale Semiconductor, Inc...
A typical monitor system operation is summarized in Figure 8-6.
Note:
User is required to check the HDET and VDET at VSIN=0 first. If either or both are not
detected, user then set VSIN=1 to check HDET and VDET. It is because if the incoming
signal is a valid composite signal, HDET and VDET are both read 1 even VSIN=1.
Note:
Each time if VDET is not detected when VSIN=1, user needs to clear VSIN to check
VDET. If VDET is still not detected, user then set VSIN to check them again to decide
what mode it is.
8
TPG
MC68HC05BD3
SYNC SIGNAL PROCESSOR
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
8-11
69
Freescale Semiconductor, Inc.
Clear 1st_time
Init VSIN=0
A
Freescale Semiconductor, Inc...
B
VDET=0?
Y
Set VSIN=1
N
Y
Y
VDET=0?
HDET=1?
Y
N
N
HOVER=1?
Set VSIN=1
Y
B
HDET=1?
N
N
HSYNC too high
No HSYNC signal
Set Standby mode
8
VDET=0?
Set SOUT=1
Y
N
Y
Read registers
HDET=1?
N
VSIN=1?
Y
Y
1st_time=0?
N
Y
Set 1st_time=1
No HSYNC
Set Standby mode
HDET=1?
N
Clear VSIN=0
N
Clear VSIN=0
Separated sync
Set Normal mode
No VSYNC
Set Suspend mode
Composite sync
Set Normal mode
No VSYNC
No HSYNC
Set Off mode
A
Figure 8-6 Typical Monitor System Operation
TPG
MOTOROLA
8-12
SYNC SIGNAL PROCESSOR
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
70
Freescale Semiconductor, Inc.
9
Freescale Semiconductor, Inc...
CPU CORE AND INSTRUCTION SET
This section provides a description of the CPU core registers, the instruction set and the
addressing modes of the MC68HC05BD3.
9.1
Registers
The MCU contains five registers, as shown in the programming model of Figure 9-1. The interrupt
stacking order is shown in Figure 9-2.
7
0
7
0
Accumulator
Index register
15
7
0 0
15
7
0 0 0 0 0 0 0 0 1 1
7
1 1 1 H I N Z
0
9
Program counter
0
Stack pointer
0
C
Condition code register
Carry / borrow
Zero
Negative
Interrupt mask
Half carry
Figure 9-1 Programming model
9.1.1
Accumulator (A)
The accumulator is a general purpose 8-bit register used to hold operands and results of
arithmetic calculations or data manipulations.
TPG
MC68HC05BD3
CPU CORE AND INSTRUCTION SET
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
9-1
71
Freescale Semiconductor, Inc.
Unstack
Stack
0
Condition code register
Accumulator
Index register
Program counter high
Program counter low
Interrupt
Increasing
memory
address
Return
7
Decreasing
memory
address
Freescale Semiconductor, Inc...
Figure 9-2 Stacking order
9.1.2
Index register (X)
The index register is an 8-bit register, which can contain the indexed addressing value used to
create an effective address. The index register may also be used as a temporary storage area.
9.1.3
Program counter (PC)
The program counter is a 16-bit register, which contains the address of the next byte to be fetched.
9.1.4
9
Stack pointer (SP)
The stack pointer is a 16-bit register, which contains the address of the next free location on the
stack. During an MCU reset or the reset stack pointer (RSP) instruction, the stack pointer is set to
location $00FF. The stack pointer is then decremented as data is pushed onto the stack and
incremented as data is pulled from the stack.
When accessing memory, the ten most significant bits are permanently set to 0000000011. These
ten bits are appended to the six least significant register bits to produce an address within the
range of $00C0 to $00FF. Subroutines and interrupts may use up to 64 (decimal) locations. If 64
locations are exceeded, the stack pointer wraps around and overwrites the previously stored
information. A subroutine call occupies two locations on the stack; an interrupt uses five locations.
9.1.5
Condition code register (CCR)
The CCR is a 5-bit register in which four bits are used to indicate the results of the instruction just
executed, and the fifth bit indicates whether interrupts are masked. These bits can be individually
tested by a program, and specific actions can be taken as a result of their state. Each bit is
explained in the following paragraphs.
Half carry (H)
This bit is set during ADD and ADC operations to indicate that a carry occurred between bits 3 and 4.
TPG
MOTOROLA
9-2
CPU CORE AND INSTRUCTION SET
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
72
Freescale Semiconductor, Inc.
Interrupt (I)
When this bit is set, all maskable interrupts are masked. If an interrupt occurs while this bit is set,
the interrupt is latched and remains pending until the interrupt bit is cleared.
Negative (N)
When set, this bit indicates that the result of the last arithmetic, logical, or data manipulation was
negative.
Freescale Semiconductor, Inc...
Zero (Z)
When set, this bit indicates that the result of the last arithmetic, logical, or data manipulation was
zero.
Carry/borrow (C)
When set, this bit indicates that a carry or borrow out of the arithmetic logical unit (ALU) occurred
during the last arithmetic operation. This bit is also affected during bit test and branch instructions
and during shifts and rotates.
9.2
Instruction set
The MCU has a set of 62 basic instructions. They can be grouped into five different types as
follows:
–
Register/memory
–
Read/modify/write
–
Branch
–
Bit manipulation
–
Control
9
The following paragraphs briefly explain each type. All the instructions within a given type are
presented in individual tables.
This MCU uses all the instructions available in the M146805 CMOS family plus one more: the
unsigned multiply (MUL) instruction. This instruction allows unsigned multiplication of the contents
of the accumulator (A) and the index register (X). The high-order product is then stored in the
index register and the low-order product is stored in the accumulator. A detailed definition of the
MUL instruction is shown in Table 9-1.
TPG
MC68HC05BD3
CPU CORE AND INSTRUCTION SET
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
9-3
73
Freescale Semiconductor, Inc.
9.2.1
Register/memory Instructions
Most of these instructions use two operands. The first operand is either the accumulator or the
index register. The second operand is obtained from memory using one of the addressing modes.
The jump unconditional (JMP) and jump to subroutine (JSR) instructions have no register
operand. Refer to Table 9-2 for a complete list of register/memory instructions.
Freescale Semiconductor, Inc...
9.2.2
Branch instructions
These instructions cause the program to branch if a particular condition is met; otherwise, no
operation is performed. Branch instructions are two-byte instructions. Refer to Table 9-3.
9.2.3
Bit manipulation instructions
The MCU can set or clear any writable bit that resides in the first 256 bytes of the memory space
(page 0). All port data and data direction registers, timer and serial interface registers,
control/status registers and a portion of the on-chip RAM reside in page 0. An additional feature
allows the software to test and branch on the state of any bit within these locations. The bit set, bit
clear, bit test and branch functions are all implemented with single instructions. For the test and
branch instructions, the value of the bit tested is also placed in the carry bit of the condition code
register. Refer to Table 9-4.
9
9.2.4
Read/modify/write instructions
These instructions read a memory location or a register, modify or test its contents, and write the
modified value back to memory or to the register. The test for negative or zero (TST) instruction is
an exception to this sequence of reading, modifying and writing, since it does not modify the value.
Refer to Table 9-5 for a complete list of read/modify/write instructions.
9.2.5
Control instructions
These instructions are register reference instructions and are used to control processor operation
during program execution. Refer to Table 9-6 for a complete list of control instructions.
9.2.6
Tables
Tables for all the instruction types listed above follow. In addition there is a complete alphabetical
listing of all the instructions (see Table 9-7), and an opcode map for the instruction set of the
M68HC05 MCU family (see Table 9-8).
TPG
MOTOROLA
9-4
CPU CORE AND INSTRUCTION SET
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
74
Freescale Semiconductor, Inc.
Table 9-1 MUL instruction
X:A ← X*A
Multiplies the eight bits in the index register by the eight
Description bits in the accumulator and places the 16-bit result in the
concatenated accumulator and index register.
H : Cleared
I : Not affected
Condition
N : Not affected
codes
Z : Not affected
C : Cleared
Source
MUL
Addressing mode
Cycles
Bytes
Opcode
Form
Inherent
11
1
$42
Table 9-2 Register/memory instructions
Addressing modes
# Cycles
# Bytes
Opcode
Indexed
(16-bit
offset)
# Cycles
# Bytes
Opcode
Indexed
(8-bit
offset)
# Cycles
Opcode
# Cycles
# Bytes
Opcode
# Bytes
Indexed
(no
offset)
Extended
# Cycles
# Bytes
Direct
Opcode
# Cycles
Opcode
Function
# Bytes
Immediate
Mnemonic
Freescale Semiconductor, Inc...
Operation
Load A from memory
LDA
A6
2
2
B6
2
3
C6
3
4
F6
1
3
E6
2
4
D6
3
5
Load X from memory
LDX
AE
2
2
BE
2
3
CE
3
4
FE
1
3
EE
2
4
DE
3
5
Store A in memory
STA
B7
2
4
C7
3
5
F7
1
4
E7
2
5
D7
3
6
Store X in memory
STX
BF
2
4
CF
3
5
FF
1
4
EF
2
5
DF
3
6
Add memory to A
ADD
AB
2
2
BB
2
3
CB
3
4
FB
1
3
EB
2
4
DB
3
5
Add memory and carry to A
ADC
A9
2
2
B9
2
3
C9
3
4
F9
1
3
E9
2
4
D9
3
5
Subtract memory
SUB
A0
2
2
B0
2
3
C0
3
4
F0
1
3
E0
2
4
D0
3
5
Subtract memory from A
with borrow
SBC
A2
2
2
B2
2
3
C2
3
4
F2
1
3
E2
2
4
D2
3
5
AND memory with A
AND
A4
2
2
B4
2
3
C4
3
4
F4
1
3
E4
2
4
D4
3
5
OR memory with A
ORA
AA
2
2
BA
2
3
CA
3
4
FA
1
3
EA
2
4
DA
3
5
Exclusive OR memory with A
EOR
A8
2
2
B8
2
3
C8
3
4
F8
1
3
E8
2
4
D8
3
5
Arithmetic compare A
with memory
CMP
A1
2
2
B1
2
3
C1
3
4
F1
1
3
E1
2
4
D1
3
5
Arithmetic compare X
with memory
CPX
A3
2
2
B3
2
3
C3
3
4
F3
1
3
E3
2
4
D3
3
5
Bit test memory with A
(logical compare)
BIT
A5
2
2
B5
2
3
C5
3
4
F5
1
3
E5
2
4
D5
3
5
Jump unconditional
JMP
BC
2
2
CC
3
3
FC
1
2
EC
2
3
DC
3
4
Jump to subroutine
JSR
BD
2
5
CD
3
6
FD
1
5
ED
2
6
DD
3
7
9
TPG
MC68HC05BD3
CPU CORE AND INSTRUCTION SET
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
9-5
75
Freescale Semiconductor, Inc.
Table 9-3 Branch instructions
Freescale Semiconductor, Inc...
Function
Branch always
Branch never
Branch if higher
Branch if lower or same
Branch if carry clear
(Branch if higher or same)
Branch if carry set
(Branch if lower)
Branch if not equal
Branch if equal
Branch if half carry clear
Branch if half carry set
Branch if plus
Branch if minus
Branch if interrupt mask bit is clear
Branch if interrupt mask bit is set
Branch if interrupt line is low
Branch if interrupt line is high
Branch to subroutine
Mnemonic
BRA
BRN
BHI
BLS
BCC
(BHS)
BCS
(BLO)
BNE
BEQ
BHCC
BHCS
BPL
BMI
BMC
BMS
BIL
BIH
BSR
Relative addressing mode
Opcode # Bytes # Cycles
20
2
3
21
2
3
22
2
3
23
2
3
24
2
3
24
2
3
25
2
3
25
2
3
26
2
3
27
2
3
28
2
3
29
2
3
2A
2
3
2B
2
3
2C
2
3
2D
2
3
2E
2
3
2F
2
3
AD
2
6
Table 9-4 Bit manipulation instructions
9
Function
Branch if bit n is set
Branch if bit n is clear
Set bit n
Clear bit n
Mnemonic
BRSET n (n=0–7)
BRCLR n (n=0–7)
BSET n (n=0–7)
BCLR n (n=0–7)
Addressing modes
Bit set/clear
Bit test and branch
Opcode # Bytes # Cycles Opcode # Bytes # Cycles
2•n
3
5
01+2•n
3
5
10+2•n
2
5
11+2•n
2
5
TPG
MOTOROLA
9-6
CPU CORE AND INSTRUCTION SET
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
76
Freescale Semiconductor, Inc.
Table 9-5 Read/modify/write instructions
Addressing modes
# Cycles
Opcode
# Bytes
# Cycles
Opcode
# Bytes
# Cycles
Opcode
# Bytes
# Cycles
Opcode
# Bytes
# Cycles
Indexed
(8-bit
offset)
# Bytes
Increment
Decrement
Clear
Complement
Negate (two’s complement)
Rotate left through carry
Rotate right through carry
Logical shift left
Logical shift right
Arithmetic shift right
Test for negative or zero
Multiply
Indexed
(no
offset)
Direct
Opcode
Freescale Semiconductor, Inc...
Function
Inherent
(X)
Mnemonic
Inherent
(A)
INC
DEC
CLR
COM
NEG
ROL
ROR
LSL
LSR
ASR
TST
MUL
4C
4A
4F
43
40
49
46
48
44
47
4D
42
1
1
1
1
1
1
1
1
1
1
1
1
3 5C
3 5A
3 5F
3 53
3 50
3 59
3 56
3 58
3 54
3 57
3 5D
11
1
1
1
1
1
1
1
1
1
1
1
3
3
3
3
3
3
3
3
3
3
3
3C
3A
3F
33
30
39
36
38
34
37
3D
2
2
2
2
2
2
2
2
2
2
2
5
5
5
5
5
5
5
5
5
5
4
7C
7A
7F
73
70
79
76
78
74
77
7D
1
1
1
1
1
1
1
1
1
1
1
5
5
5
5
5
5
5
5
5
5
4
6C
6A
6F
63
60
69
66
68
64
67
6D
2
2
2
2
2
2
2
2
2
2
2
6
6
6
6
6
6
6
6
6
6
5
Table 9-6 Control instructions
Function
Transfer A to X
Transfer X to A
Set carry bit
Clear carry bit
Set interrupt mask bit
Clear interrupt mask bit
Software interrupt
Return from subroutine
Return from interrupt
Reset stack pointer
No-operation
Stop
Wait
Mnemonic
TAX
TXA
SEC
CLC
SEI
CLI
SWI
RTS
RTI
RSP
NOP
STOP
WAIT
9
Inherent addressing mode
Opcode # Bytes # Cycles
97
1
2
9F
1
2
99
1
2
98
1
2
9B
1
2
9A
1
2
83
1
10
81
1
6
80
1
9
9C
1
2
9D
1
2
8E
1
2
8F
1
2
TPG
MC68HC05BD3
CPU CORE AND INSTRUCTION SET
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
9-7
77
Freescale Semiconductor, Inc.
Table 9-7 Instruction set
Freescale Semiconductor, Inc...
Mnemonic
9
INH
IMM
DIR
Addressing modes
EXT REL IX
IX1
IX2
BSC BTB
H
◊
◊
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ADC
ADD
AND
ASL
ASR
BCC
BCLR
BCS
BEQ
BHCC
BHCS
BHI
BHS
BIH
BIL
BIT
BLO
BLS
BMC
BMI
BMS
BNE
BPL
BRA
BRN
BRCLR
BRSET
BSET
BSR
CLC
CLI
CLR
CMP
Address mode abbreviations
BSC Bit set/clear
IMM
Immediate
BTB
Bit test & branch
IX
Indexed (no offset)
DIR
Direct
IX1
EXT
Extended
IX2
INH
Inherent
REL
Relative
Condition codes
I
N Z
•
◊ ◊
•
◊ ◊
•
◊ ◊
•
◊ ◊
•
◊ ◊
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
◊ ◊
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
0
•
•
•
0 1
•
◊ ◊
C
◊
◊
•
◊
◊
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
◊
◊
•
•
0
•
•
◊
Condition code symbols
◊
Tested and set if true,
cleared otherwise
H
Half carry (from bit 3)
Indexed, 1 byte offset
I
Interrupt mask
•
Not affected
Indexed, 2 byte offset
N
Negate (sign bit)
?
Load CCR from stack
Z
Zero
0
Cleared
C
Carry/borrow
1
Set
Not implemented
TPG
MOTOROLA
9-8
CPU CORE AND INSTRUCTION SET
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
78
Freescale Semiconductor, Inc.
Table 9-7 Instruction set (Continued)
Freescale Semiconductor, Inc...
Mnemonic
INH
IMM
DIR
Addressing modes
EXT REL IX
IX1
IX2
BSC BTB
H
•
•
•
•
•
•
•
•
•
•
•
0
•
•
•
•
•
•
?
•
•
•
•
•
•
•
•
•
•
•
•
•
COM
CPX
DEC
EOR
INC
JMP
JSR
LDA
LDX
LSL
LSR
MUL
NEG
NOP
ORA
ROL
ROR
RSP
RTI
RTS
SBC
SEC
SEI
STA
STOP
STX
SUB
SWI
TAX
TST
TXA
WAIT
Address mode abbreviations
BSC Bit set/clear
IMM
Immediate
BTB
Bit test & branch
IX
Indexed (no offset)
DIR
Direct
IX1
EXT
Extended
IX2
INH
Inherent
REL
Relative
Condition codes
I
N Z
•
◊ ◊
•
◊ ◊
•
◊ ◊
•
◊ ◊
•
◊ ◊
•
•
•
•
•
•
•
◊ ◊
•
◊ ◊
•
◊ ◊
•
0 ◊
•
•
•
•
◊ ◊
•
•
•
•
◊ ◊
•
◊ ◊
•
◊ ◊
•
•
•
? ? ?
•
•
•
•
◊ ◊
•
•
•
1
•
•
•
◊ ◊
0
•
•
•
◊ ◊
•
◊ ◊
1
•
•
•
•
•
•
◊ ◊
•
•
•
0
•
•
C
1
◊
•
•
•
•
•
•
•
◊
◊
0
◊
•
•
◊
◊
•
?
•
◊
1
•
•
•
•
◊
•
•
•
•
•
9
Condition code symbols
◊
Tested and set if true,
cleared otherwise
H
Half carry (from bit 3)
Indexed, 1 byte offset
I
Interrupt mask
•
Not affected
Indexed, 2 byte offset
N
Negate (sign bit)
?
Load CCR from stack
Z
Zero
0
Cleared
C
Carry/borrow
1
Set
Not implemented
TPG
MC68HC05BD3
CPU CORE AND INSTRUCTION SET
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
9-9
79
MOTOROLA
9-10
BTB 2
5
BTB 2
5
BTB 2
5
3
3
BTB 2
5
BTB 2
5
BTB 2
5
BTB 2
5
BTB 2
5
BTB 2
5
BTB 2
5
BTB 2
5
BTB 2
5
BTB 2
5
BTB 2
3
3
3
3
3
3
3
3
3
3
BRCLR7
BRSET7
BRCLR6
BRSET6
BRCLR5
BRSET5
BRCLR4
BRSET4
BRCLR3
BRSET3
BTB 2
5
3
BRCLR2
3
BRSET2
BRCLR1
BRSET1
BTB 2
5
3
BRCLR0
3
BRSET0
5
BSC 2
BSC 2
5
BCLR7
BSET7
BSC 2
5
BSC 2
5
BCLR6
BSET6
BSC 2
5
BSC 2
5
BCLR5
BSET5
BSC 2
5
BCLR4
BSC 2
5
BSET4
BSC 2
5
BSC 2
5
BCLR3
BSET3
BSC 2
5
BSC 2
5
BCLR2
BSET2
BSC 2
5
BSC 2
5
BCLR1
BSET1
BSC 2
5
BSC 2
5
BCLR0
BSET0
5
BIH
BIL
BMS
BMC
BMI
BPL
REL 2
REL
3
REL 2
3
REL 2
3
REL
3
REL 2
3
REL 2
3
BHCS
REL 2
3
REL 2
3
REL 2
3
REL
3
REL 2
3
REL 2
3
REL
3
REL
3
REL 2
3
BHCC
BEQ
BNE
BCS
BCC
BLS
BHI
BRN
BRA
3
BSC
BTB
DIR
EXT
INH
IMM
Bit set/clear
Bit test and branch
Direct
Extended
Inherent
Immediate
IX
IX1
IX2
REL
A
X
Abbreviations for address modes and registers
0
0000
1
0001
2
0010
3
0011
4
0100
5
0101
6
0110
7
0111
8
1000
9
1001
A
1010
B
1011
C
1100
D
1101
E
1110
F
1111
Low
High
Branch
REL
2
0010
CLR
TST
INC
DEC
ROL
LSL
ASR
ROR
LSR
COM
NEG
DIR
3
0011
1
CLRA
TSTA
INCA
DECA
ROLA
LSLA
ASRA
RORA
LSRA
COMA
MUL
NEGA
INH 1
3
INH 1
INH 1
3
3
INH 1
INH 1
3
INH 1
3
INH 1
3
INH 1
3
3
INH 1
INH 1
3
INH
3
11
INH 1
3
CLRX
TSTX
INCX
DECX
ROLX
LSLX
ASRX
RORX
LSRX
COMX
NEGX
INH 2
3
INH 2
INH 2
3
3
INH 2
INH 2
3
INH 2
3
INH 2
3
INH 2
3
3
INH 2
INH 2
3
3
INH 2
3
CLR
TST
INC
DEC
ROL
LSL
ASR
ROR
LSR
COM
NEG
Read/modify/write
INH
IX1
5
6
0101
0110
Indexed (no offset)
Indexed, 1 byte (8-bit) offset
Indexed, 2 byte (16-bit) offset
Relative
Accumulator
Index register
DIR 1
5
DIR 1
DIR 1
4
5
DIR 1
DIR 1
5
DIR 1
5
DIR 1
5
DIR 1
5
5
DIR 1
DIR 1
5
5
DIR 1
5
INH
4
0100
IX1 1
6
IX1 1
IX1 1
5
6
IX1 1
IX1 1
6
IX1 1
6
IX1 1
6
IX1 1
6
6
IX1 1
IX1 1
6
6
IX1 1
6
9
Bit manipulation
BTB
BSC
0
1
0000
0001
CLR
TST
INC
DEC
ROL
LSL
ASR
ROR
LSR
COM
NEG
IX
7
0111
5
1
WAIT
STOP
SWI
RTS
RTI
1
1
1
1
1
1
1
INH 1
INH
2
2
INH
10
INH
INH
6
9
TXA
NOP
RSP
SEI
CLI
SEC
CLC
TAX
INH
9
1001
Control
Not implemented
IX 1
5
IX
IX
4
5
IX
IX
5
IX
5
IX
5
IX
5
5
IX
IX 1
5
1
IX 1
5
INH
8
1000
2
2
INH
2
2
INH 2
INH
2
INH 2
2
INH 2
2
INH 2
2
INH 2
2
INH
2
2
2
2
2
2
2
LDX
BSR
ADD
ORA
ADC
EOR
LDA
BIT
AND
CPX
SBC
CMP
SUB
IMM
A
1010
2
2
STX
LDX
JSR
JMP
ADD
ORA
ADC
EOR
STA
LDA
BIT
AND
CPX
SBC
CMP
SUB
3
CPU CORE AND INSTRUCTION SET
For More Information On This Product,
Go to: www.freescale.com
Bytes
1
STX
LDX
JSR
JMP
ADD
ORA
ADC
EOR
STA
LDA
BIT
AND
CPX
SBC
CMP
SUB
SUB
F
1111
EXT 3
EXT 3
5
EXT 3
4
EXT 3
6
EXT 3
3
EXT 3
4
EXT 3
4
EXT 3
4
EXT 3
4
EXT 3
5
EXT 3
4
EXT 3
4
EXT 3
4
EXT 3
4
EXT 3
4
EXT 3
4
4
IX
3
0
0000
IX2 2
IX2 2
6
IX2 2
5
IX2 2
7
IX2 2
4
IX2 2
5
IX2 2
5
IX2 2
5
IX2 2
5
IX2 2
6
IX2 2
5
IX2 2
5
IX2 2
5
IX2 2
5
IX2 2
5
IX2 2
5
5
STX
LDX
JSR
JMP
ADD
ORA
ADC
EOR
STA
LDA
BIT
AND
CPX
SBC
CMP
SUB
IX1
E
1110
Address mode
STX
LDX
JSR
JMP
ADD
ORA
ADC
EOR
STA
LDA
BIT
AND
CPX
SBC
CMP
SUB
Register/memory
EXT
IX2
C
D
1100
1101
Cycles
DIR 3
DIR 3
4
DIR 3
3
DIR 3
5
DIR 3
2
DIR 3
3
DIR 3
3
DIR 3
3
DIR 3
3
DIR 3
4
DIR 3
3
DIR 3
3
DIR 3
3
DIR 3
3
DIR 3
3
DIR 3
3
Mnemonic
Legend
2
IMM 2
REL 2
2
6
IMM 2
IMM 2
2
IMM 2
2
IMM 2
2
2
IMM 2
IMM 2
2
IMM 2
2
IMM 2
2
IMM 2
2
IMM 2
2
IMM 2
2
2
DIR
B
1011
Freescale Semiconductor, Inc...
STX
LDX
JSR
JMP
ADD
ORA
ADC
EOR
STA
LDA
BIT
AND
CPX
SBC
CMP
SUB
IX
IX
4
IX
3
IX
5
IX
2
IX
3
IX
3
IX
3
IX
3
IX
4
IX
3
IX
3
IX
3
IX
3
IX
3
IX
3
3
Low
0
0000
1
0001
2
0010
3
0011
4
0100
5
0101
6
0110
7
0111
8
1000
9
1001
A
1010
B
1011
C
1100
D
1101
E
1110
F
1111
High
Opcode in binary
Opcode in hexadecimal
IX1 1
IX1 1
5
IX1 1
4
IX1 1
6
IX1 1
3
IX1 1
4
IX1 1
4
IX1 1
4
IX1 1
4
IX1 1
5
IX1 1
4
IX1 1
4
IX1 1
4
IX1 1
4
IX1 1
4
IX1 1
4
4
IX
F
1111
Freescale Semiconductor, Inc.
Table 9-8 M68HC05 opcode map
MC68HC05BD3
TPG
80
Freescale Semiconductor, Inc.
9.3
Addressing modes
Freescale Semiconductor, Inc...
Ten different addressing modes provide programmers with the flexibility to optimize their code for
all situations. The various indexed addressing modes make it possible to locate data tables, code
conversion tables and scaling tables anywhere in the memory space. Short indexed accesses are
single byte instructions; the longest instructions (three bytes) enable access to tables throughout
memory. Short absolute (direct) and long absolute (extended) addressing are also included. One
or two byte direct addressing instructions access all data bytes in most applications. Extended
addressing permits jump instructions to reach all memory locations.
The term ‘effective address’ (EA) is used in describing the various addressing modes. The
effective address is defined as the address from which the argument for an instruction is fetched
or stored. The ten addressing modes of the processor are described below. Parentheses are used
to indicate ‘contents of’ the location or register referred to. For example, (PC) indicates the
contents of the location pointed to by the PC (program counter). An arrow indicates ‘is replaced
by’ and a colon indicates concatenation of two bytes. For additional details and graphical
illustrations, refer to the M6805 HMOS/M146805 CMOS Family Microcomputer/
Microprocessor User's Manual or to the M68HC05 Applications Guide.
9.3.1
Inherent
In the inherent addressing mode, all the information necessary to execute the instruction is
contained in the opcode. Operations specifying only the index register or accumulator, as well as
the control instruction, with no other arguments are included in this mode. These instructions are
one byte long.
9.3.2
9
Immediate
In the immediate addressing mode, the operand is contained in the byte immediately following the
opcode. The immediate addressing mode is used to access constants that do not change during
program execution (e.g. a constant used to initialize a loop counter).
EA = PC+1; PC ← PC+2
9.3.3
Direct
In the direct addressing mode, the effective address of the argument is contained in a single byte
following the opcode byte. Direct addressing allows the user to directly address the lowest 256
bytes in memory with a single two-byte instruction.
EA = (PC+1); PC ← PC+2
Address bus high ← 0; Address bus low ← (PC+1)
TPG
MC68HC05BD3
CPU CORE AND INSTRUCTION SET
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
9-11
81
Freescale Semiconductor, Inc.
9.3.4
Extended
In the extended addressing mode, the effective address of the argument is contained in the two
bytes following the opcode byte. Instructions with extended addressing mode are capable of
referencing arguments anywhere in memory with a single three-byte instruction. When using the
Motorola assembler, the user need not specify whether an instruction uses direct or extended
addressing. The assembler automatically selects the short form of the instruction.
Freescale Semiconductor, Inc...
EA = (PC+1):(PC+2); PC ← PC+3
Address bus high ← (PC+1); Address bus low ← (PC+2)
9.3.5
Indexed, no offset
In the indexed, no offset addressing mode, the effective address of the argument is contained in
the 8-bit index register. This addressing mode can access the first 256 memory locations. These
instructions are only one byte long. This mode is often used to move a pointer through a table or
to hold the address of a frequently referenced RAM or I/O location.
EA = X; PC ← PC+1
Address bus high ← 0; Address bus low ← X
9.3.6
9
Indexed, 8-bit offset
In the indexed, 8-bit offset addressing mode, the effective address is the sum of the contents of
the unsigned 8-bit index register and the unsigned byte following the opcode. Therefore the
operand can be located anywhere within the lowest 511 memory locations. This addressing mode
is useful for selecting the mth element in an n element table.
EA = X+(PC+1); PC ← PC+2
Address bus high ← K; Address bus low ← X+(PC+1)
where K = the carry from the addition of X and (PC+1)
9.3.7
Indexed, 16-bit offset
In the indexed, 16-bit offset addressing mode, the effective address is the sum of the contents of
the unsigned 8-bit index register and the two unsigned bytes following the opcode. This address
mode can be used in a manner similar to indexed, 8-bit offset except that this three-byte instruction
allows tables to be anywhere in memory. As with direct and extended addressing, the Motorola
assembler determines the shortest form of indexed addressing.
EA = X+[(PC+1):(PC+2)]; PC ← PC+3
Address bus high ← (PC+1)+K; Address bus low ← X+(PC+2)
where K = the carry from the addition of X and (PC+2)
TPG
MOTOROLA
9-12
CPU CORE AND INSTRUCTION SET
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
82
Freescale Semiconductor, Inc.
9.3.8
Relative
Freescale Semiconductor, Inc...
The relative addressing mode is only used in branch instructions. In relative addressing, the
contents of the 8-bit signed byte (the offset) following the opcode are added to the PC if, and only
if, the branch conditions are true. Otherwise, control proceeds to the next instruction. The span of
relative addressing is from –126 to +129 from the opcode address. The programmer need not
calculate the offset when using the Motorola assembler, since it calculates the proper offset and
checks to see that it is within the span of the branch.
EA = PC+2+(PC+1); PC ← EA if branch taken;
otherwise EA = PC ← PC+2
9.3.9
Bit set/clear
In the bit set/clear addressing mode, the bit to be set or cleared is part of the opcode. The byte
following the opcode specifies the address of the byte in which the specified bit is to be set or
cleared. Any read/write bit in the first 256 locations of memory, including I/O, can be selectively
set or cleared with a single two-byte instruction.
EA = (PC+1); PC ← PC+2
Address bus high ← 0; Address bus low ← (PC+1)
9.3.10
Bit test and branch
The bit test and branch addressing mode is a combination of direct addressing and relative
addressing. The bit to be tested and its condition (set or clear) is included in the opcode. The
address of the byte to be tested is in the single byte immediately following the opcode byte (EA1).
The signed relative 8-bit offset in the third byte (EA2) is added to the PC if the specified bit is set
or cleared in the specified memory location. This single three-byte instruction allows the program
to branch based on the condition of any readable bit in the first 256 locations of memory. The span
of branch is from –125 to +130 from the opcode address. The state of the tested bit is also
transferred to the carry bit of the condition code register.
9
EA1 = (PC+1); PC ← PC+2
Address bus high ← 0; Address bus low ← (PC+1)
EA2 = PC+3+(PC+2); PC ← EA2 if branch taken;
otherwise PC ← PC+3
TPG
MC68HC05BD3
CPU CORE AND INSTRUCTION SET
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
9-13
83
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
THIS PAGE LEFT BLANK INTENTIONALLY
9
TPG
MOTOROLA
9-14
CPU CORE AND INSTRUCTION SET
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
84
Freescale Semiconductor, Inc.
10
Freescale Semiconductor, Inc...
LOW POWER MODES
The MC68HC05BD3 has only one low-power operating mode–the Wait Mode. The WAIT
instruction provides the only mode that reduces the power required for the MCU by stopping CPU
internal clock. The STOP instruction is not implemented in its normal sense. The STOP instruction
will be interpreted as the NOP instruction by the CPU if it is ever encountered. The flow of the WAIT
mode is shown in Figure 10-1.
10.1
STOP Mode
Stop mode is not implemented on the MC68HC05BD3. The STOP instruction will be treated and
executed as a NOP instruction. Therefore, the I-bit in the Condition Code register will not be
cleared.
10.2
WAIT Mode
In the WAIT mode the internal processor clock is halted, suspending all processor and internal bus
activities. Other Internal clocks remain active, permitting interrupts to be generated from the
Multi-Function Timer, M-Bus Interface, and the Sync Signal Processor, or a reset to be generated
from the COP watchdog timer. The timer may be used to generate a periodic exit from the WAIT
mode. Execution of the WAIT instruction automatically clears the I-bit in the Condition Code
register, so that any hardware interrupt can wake up the MCU. All other registers, memory, and
input/output lines remain in their previous states.
10
TPG
MC68HC05BD3
LOW POWER MODES
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
10-1
85
Freescale Semiconductor, Inc.
10.3
COP Watchdog Timer Considerations
The COP watchdog timer is always enabled in MC68HC05BD3. It will reset the MCU when it times
out. For a system that must have intentional uses of the WAIT Mode, care must be taken to prevent
such situations from happening during normal operations by arranging timely interrupts to reset
the COP watchdog timer.
Freescale Semiconductor, Inc...
WAIT
External oscillator active
and
Internal Timer Clock Active
Stop internal processor clock,
Clear I bit in CCR
External
reset?
Y
N
Internal COP
reset?
Y
N
10
External H/W
reset?
Y
N
Internal
interrupt?
Y
Restart internal
processor clock
N
1. Fetch reset vector
or
2. Service interrupt
a. Stack
b. Set I bit
c. Vector to interrupt routine
Figure 10-1 WAIT Flowchart
TPG
MOTOROLA
10-2
LOW POWER MODES
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
86
Freescale Semiconductor, Inc.
11
Freescale Semiconductor, Inc...
OPERATING MODES
The MC68HC05BD3/MC68HC05BD5/MC68HC705BD3 MCU has two modes of operation, the
User Mode and the Self-Check/Bootstrap Mode. Figure 11-1 shows the flowchart of entry to these
two modes, and Table 11-1 shows operating mode selection.
5V
RESET
9V
IRQ
?
N
USER MODE
(NORMAL MODE)
Y
PB5 = VDD ?
Y
SELF-CHECK/
BOOTSTRAP
MODE
11
Note:
Self-check mode is for MC68HC05BD3/BD5
Bootstrap mode is for MC68HC705BD3
Figure 11-1 Flowchart of Mode Entering
TPG
MC68HC05BD3
OPERATING MODES
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
11-1
87
Freescale Semiconductor, Inc.
Table 11-1 Mode Selection
RESET
5V
5V
IRQ
PB5
MODE
VSS to VDD
VSS to VDD
USER
VDD
SELF-CHECK/
BOOTSTRAP
9V
+9V Rising Edge*
Freescale Semiconductor, Inc...
* Minimum hold time should be 2 clock cycles, after that it can be used as a normal IRQ
function pin.
11.1
User Mode (Normal Operation)
The normal operating mode of the MC68HC05BD3/MC68HC05BD5/MC68HC705BD3 is the user
mode. The user mode will be entered if the RESET line is brought low, and the IRQ pin is within
its normal operational range (VSS to VDD), the rising edge of the RESET will cause the MCU to
enter the user mode.
11.2
11
Self-Check Mode
The self-check mode is provided on the MC68HC05BD3 and MC68HC05BD5 for the user to
check device functions with an on-chip self-check program masked at location $3F00 to $3FDF
under minimum hardware support. The hardware is shown in Figure 11-3. Figure 11-2 is the
criteria to enter self-check mode, where PB5’s condition is latched within first two clock cycles after
the rising edge of the reset. PB5 can then be used for other purposes. After entering the self-check
mode, CPU branches to the self-check program and carries out the self-check. Self-check is a
repetitive test, i.e. if all parts are checked to be good, the CPU will repeat the self-check again.
Therefore, the LEDs attached to Port B will be flashing if the device is good; else the combination
of LEDs’ on-off pattern can show what part of the device is suspected to be bad. Table 11-2 lists
the LEDs’ on-off patterns and their corresponding indications.
+5V
PB5
+9V
IRQ
+5V
RESET
Figure 11-2 Self-Check Mode Timing
TPG
MOTOROLA
11-2
OPERATING MODES
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
88
Freescale Semiconductor, Inc.
+5V
+9V
8 x 4K7
10K
IRQ
PD0/SDA
PC0/PWM8
PC1/PWM9
PC2/PWM10
VSYNC
PC3/PWM11
HSYNC
PC4/PWM12
PC5/PWM13
XTAL
PC6/PWM14/VTTL
PC7/PWM15/HTTL
PD1/SCL
10K
4MHz
EXTAL
+5V
8 x 100
Freescale Semiconductor, Inc...
10K
2N3904
MC68HC05BD3
20p
10K
20p
1N4148
RESET
RESET
2.2µ
+5V
+
3 x 4K7
+5V
1K
PB0
D1
1K
PB1
D2
1K
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
PWM0
PWM1
PWM2
PWM3
PWM4
PWM5
PWM6
PWM7
PB2
11
+5V
PB3
D3
PB4
PB5
VDD
VSS
+
47µ
0.1µ
Figure 11-3 MC68HC05BD3 Self-Test Circuit
TPG
MC68HC05BD3
OPERATING MODES
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
11-3
89
Freescale Semiconductor, Inc.
Table 11-2 Self-Check Report
PB1
PB0
Flashing
1
1
0
1
0
1
1
0
0
0
1
1
1=LED off, 0=LED on
Freescale Semiconductor, Inc...
PB3
11.3
REMARKS
O.K. (self-check is on-going)
Bad I/O
BAD RAM
BAD ROM
BAD IRQ
Bootstrap Mode
The bootstrap mode is provided in the EPROM part (MC68HC705BD3) as a mean of
self-programming its EPROM with minimal circuitry. It is entered on the rising edge of RESET if
IRQ pin is at 1.8VDD and PB5 is at logic one. RESET must be held low for 4064 cycles after POR
(power-on reset) or for a time tRL for any other reset. The user EPROM consists of 7.75K-bytes,
from location $2000 to $3EFF.
Refer to Section 15 for further details on MC68HC705BD3.
11
TPG
MOTOROLA
11-4
OPERATING MODES
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
90
Freescale Semiconductor, Inc.
12
Freescale Semiconductor, Inc...
ELECTRICAL SPECIFICATIONS
This section contains the electrical specifications for MC68HC05BD3.
12.1
Maximum Ratings
(Voltages referenced to VSS)
RATINGS
Supply Voltage
Input Voltage
IRQ
Current Drain per pin excluding VDD and VSS
Operating Temperature
Storage Temperature Range
SYMBOL
VDD
Vin
Vin
ID
TA
Tstg
VALUE
–0.3 to +7.0
VSS –0.3 to VDD +0.3
VSS –0.3 to 2xVDD +0.3
25
0 to 70
–65 to +150
UNIT
V
V
V
mA
°C
°C
This device contains circuitry to protect the inputs against damage due to high static voltages or
electric fields. However, it is advised that normal precautions should be taken to avoid application
of any voltage higher than the maximum rated voltages to this high impedance circuit. For proper
operation it is recommended that Vin and Vout be constrained to the range VSS ≤(Vin or Vout)≤VDD.
Reliability of operation is enhanced if unused inputs are connected to an appropriate logic voltage
level (e.g. either VSS or VDD).
12.2
12
Thermal Characteristics
CHARACTERISTICS
Thermal resistance
- Plastic 40-pin DIP package
- Plastic 42-pin SDIP package
SYMBOL
VALUE
UNIT
θJA
θJA
60
60
°C/W
°C/W
TPG
MC68HC05BD3
ELECTRICAL SPECIFICATIONS
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
12-1
91
Freescale Semiconductor, Inc.
12.3
DC Electrical Characteristics
Freescale Semiconductor, Inc...
Table 12-1 DC Electrical Characteristics for MC68HC05BD3
(VDD =5.0Vdc ±10%, VSS =0Vdc, temperature range=0 to 70°C)
CHARACTERISTICS
SYMBOL
MINIMUM
Output voltage
ILOAD = –10µA
VOH
VDD-0.1
ILOAD = +10µA
VOL
–
Output high voltage (ILOAD=–5mA)
VOH
VDD-0.8
PA0-PA7, PB0-PB1, PC6-PC7, PD0-PD1
Output low voltage (ILOAD=+5mA)
PA0-PA7, PB0-PB5, PC0-PC7, PD0-PD1,
VOL
–
PWM0-PWM7
Input high voltage
PA0-PA7, PB0-PB5, PC0-PC7, PD0-PD1,
VIH
0.7xVDD
IRQ, RESET, EXTAL
2.0
VSYNC, HSYNC (TTL level)
Input low voltage
PA0-PA7, PB0-PB5, PC0-PC7, PD0-PD1,
VIL
VSS
IRQ, RESET, EXTAL
VSS
VSYNC, HSYNC (TTL level)
Supply current:
Run
IDD
–
Wait
–
I/O ports high-Z leakage current
PA0-PA7, PB0-PB5, PC0-PC7, PD0-PD1,
IIL
–
PWM0-PWM7
Input current
IIN
–
IRQ, RESET, EXTAL, VSYNC, HSYNC
Capacitance
COUT
–
ports (as input or output), RESET, IRQ,
CIN
–
EXTAL, XTAL, HSYNC, VSYNC
Notes:
(1) All values shown reflect average measurements.
TYPICAL
MAXIMUM
UNIT
–
–
–
0.1
V
V
–
–
V
–
0.4
V
–
–
VDD
VDD
V
0.2xVDD
0.8
V
4.5
0.73
20
8
mA
mA
–
±10
µA
–
1
µA
–
–
12
8
pF
pF
–
–
(2) Typical values at midpoint of voltage range, 25°C only.
(3) Wait IDD: only timer system and SSP is active.
12
(4) Run (operating) IDD, Wait IDD: measured using external square wave clock source to EXTAL (fOSC =4.2MHz),
all inputs 0.2 Vdc from rail; no dc loads, less than 50pF on all outputs, CL =20pF on EXTAL.
(5) Wait IDD: all ports configured as inputs, VIL =0.2 Vdc, VIH =VDD – 0.2 Vdc.
(6) Wait IDD is affected linearly by the EXTAL capacitance.
TPG
MOTOROLA
12-2
ELECTRICAL SPECIFICATIONS
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
92
Freescale Semiconductor, Inc.
12.4
Control Timing
Freescale Semiconductor, Inc...
Table 12-2 Control Timing
(VDD =5.0Vdc ±10%, VSS =0Vdc, temperature range=0 to 70°C)
CHARACTERISTICS
SYMBOL
MINIMUM MAXIMUM UNIT
Frequency of operation
–
4.2
MHz
Crystal option
fOSC
dc
4.2
MHz
External clock option
Internal operating frequency (fOSC/2)
Crystal
fOP
–
2.1
MHz
External clock
fOP
dc
2.1
MHz
Processor cycle time
tCYC
480
–
ns
Crystal oscillator start-up time
tOXOV
–
100
ms
External RESET pulse width
tRL
1.5
–
tCYC
Watchdog RESET output pulse width
tDOGL
1.5
–
tCYC
Watchdog time-out
tDOG
114688
917504
tCYC
Interrupt pulse width (edge-triggered)
tILIH
125
–
ns
Interrupt pulse period
tILIL
–(1)
–
tCYC
EXTAL pulse width
tOH, tOL
100
–
tCYC
Notes:
(1) The minimum period tILIL should not be less than the number of cycles it takes to execute the
interrupt service routine plus 21 tCYC.
12
TPG
MC68HC05BD3
ELECTRICAL SPECIFICATIONS
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
12-3
93
Freescale Semiconductor, Inc.
12.5
M-Bus Timing
Freescale Semiconductor, Inc...
Table 12-3 M-Bus Interface Input Signal Timing
(VDD =5.0Vdc ±10%, VSS =0Vdc, temperature range=0 to 70°C)
PARAMETER
SYMBOL
MINIMUM
START condition hold time
tHD.STA
2
Clock low period
tLOW
4.7
Clock high period
tHIGH
4
Data set-up time
tSU.DAT
250
Data hold time
tHD.DAT
0
START condition set-up time
tSU.STA
2
(for repeated START condition only)
STOP condition set-up time
tSU.STO
2
MAXIMUM
–
–
–
–
–
UNIT
tCYC
tCYC
tCYC
ns
tCYC
–
tCYC
–
tCYC
Table 12-4 M-Bus Interface Output Signal Timing
(VDD =5.0Vdc ±10%, VSS =0Vdc, temperature range=0 to 70°C)
PARAMETER
SYMBOL
MINIMUM
START condition hold time
tHD.STA
8
Clock low period
tLOW
11
Clock high period
tHIGH
11
SDA/SCL rise time (see note 1)
tR
–
SDA/SCL fall time (see note 1)
tF
–
Data set-up time
tSU.DAT
tLOW – tCYC
Data hold time
tHD.DAT
1
START condition set-up time
tSU.STA
10
(for repeated START condition only)
STOP condition set-up time
tSU.STO
10
Note:
MAXIMUM
–
–
–
1
300
–
–
UNIT
tCYC
tCYC
tCYC
µs
ns
ns
tCYC
–
tCYC
–
tCYC
1. With 200pF loading on the SDA/SCL pins
12
SDA
tR
tF
SCL
tHD.STA
tLOW
tHIGH
tSU.DAT
tHD.DAT
tSU.STA
tSU.STO
Figure 12-1 M-Bus Timing
TPG
MOTOROLA
12-4
ELECTRICAL SPECIFICATIONS
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
94
Freescale Semiconductor, Inc.
12.6
Sync Signal Processor Timing
Freescale Semiconductor, Inc...
Table 12-5 Sync Signal Processor Timing
(VDD =5.0Vdc ±10%, VSS =0Vdc, temperature range=0 to 70°C)
PARAMETER
SYMBOL
VSYNC input sync pulse
tVI.SP
HSYNC input sync pulse
tHI.SP
(except for composite sync input)
VTTL output sync pulse width for separate sync input
tVO.SP
VTTL output sync pulse width for composite sync input
tVO.CO
HTTL output sync pulse width
tHO
Free-running VTTL output sync pulse (SOUT clear)
tFVO.SP
Free-running VTTL output period (SOUT clear)
tFVO
Free-running HTTL output sync pulse (SOUT clear)
tFHO.SP
Free-running HTTL output period (SOUT clear)
tFHO
Inserted HTTL sync pulse (INSRT cleared)
tIHI.SP
Inserted HTTL period error (INSRT cleared)
tIHI.ER
VSYNC to VTTL delay (8pF loading)
tVDD
HSYNC to HTTL delay (8pF loading)
tHHD
HSYNC to VTTL delay (composite sync)
tHVD
MINIMUM
1
MAXIMUM
1
same as input
input + 9.5µs input + 10µs
same as input
128
31488
4
41/32
4
–
1
30
40
30
40
30
40
UNIT
tCYC
tCYC
tCYC
tCYC
tCYC
tCYC
tCYC
tCYC
ns
ns
ns
12
TPG
MC68HC05BD3
ELECTRICAL SPECIFICATIONS
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
12-5
95
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
THIS PAGE LEFT BLANK INTENTIONALLY
12
TPG
MOTOROLA
12-6
ELECTRICAL SPECIFICATIONS
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
96
Freescale Semiconductor, Inc.
13
Freescale Semiconductor, Inc...
MECHANICAL SPECIFICATIONS
This section provides the mechanical dimension for the 42-pin SDIP and 40-pin DIP packages for
the MC68HC05BD3.
13.1
42-Pin SDIP Package (Case 858-01)
-A42
! ! % ! ! ! #
! " $" 22
-B1
21
L
H
C
-T K
13.2
N
G
F
D 42 PL
M
J 42 PL
! °
°
°
°
! 40-Pin DIP Package (Case 711-03)
40
! ! ! #! %% ! $"
! ! ! ! !
!
! ! #
! " 21
B
1
20
A
L
C
N
J
H
G
F
D
K
M
°
°
°
°
13
TPG
MC68HC05BD3
MECHANICAL SPECIFICATIONS
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
13-1
97
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
THIS PAGE LEFT BLANK INTENTIONALLY
13
TPG
MOTOROLA
13-2
MECHANICAL SPECIFICATIONS
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
98
Freescale Semiconductor, Inc.
14
Freescale Semiconductor, Inc...
MC68HC705BD3
The MC68HC705BD3 is functionally equivalent to MC68HC05BD3, but with increased RAM size
to 256 bytes and the user ROM is replaced by an 7.75K-bytes user EPROM (located from $2000
to $3EFF). The entire MC68HC05BD3 data sheet applies to the MC68HC705BD3, with
exceptions outlined in the section.
14.1
Features
•
Functionally equivalent to MC68HC05BD3
•
256 bytes on-chip RAM
•
7.75K-bytes user EPROM
14.2
Memory Map
Figure 14-1 shows the memory map for the MC68HC705BD3.
14.3
EPROM Programming
The following programming boards are available from Motorola for programming the on-chip
EPROM in the MC68HC705BD3.
Table 14-1 MC68HC705BD3 Programming Boards
Platform board
For programming a single device at a time:
For programming up to 10 devices at a time:
M68HC705UPGMR
M68HC705UGANG
+
Adapter
M68UPA05BD3P40
for 40-pin PDIP
M68UPA05BD3B42
for 42-pin SDIP
14
TPG
MC68HC05BD3
MC68HC705BD3
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
14-1
99
Freescale Semiconductor, Inc.
MC68HC705BD3
$0000
I/O
48 Bytes
$002F
$0030
Unused
$007F
$0080
$00C0
Freescale Semiconductor, Inc...
$00FF
Stack
64 Bytes
User RAM
256 Bytes
$017F
$0180
Unused
$1DFF
$1E00
Bootstrap ROM
480 Bytes
$1FDF
$1FE0
$1FFF
$2000
Unused
User EPROM
7936 Bytes
$3EFF
$3F00
Unused
$3FDF
$3FE0
$3FEF
$3FF0
Bootstrap
Vectors
16 Bytes
User Vectors
16 Bytes
Port A Data Register
Port B Data Register
Port C Data Register
Port D Data Register
Port A Data Direction Register
Port B Data Direction Register
Port C Data Direction Register
Port D Data Direction Register
MFT Control and Status Register
MFT Timer Counter Register
Configuration Register 1
Configuration Register 2
SSP Control and Status Register
Vertical Frequency High Register
Vertical Frequency Low Register
Line Frequency High Register
Line Frequency Low Register
Sync Signal Control Register
Unused
Unused
Unused
Unused
Unused
MBUS Address Register
MBUS Frequency Divider Register
MBUS Control Register
MBUS Status Register
MBUS Data Register
Unused
Programming Control Register
HSYNC Period Width Register
Reserved
PWM0
PWM1
PWM2
PWM3
PWM4
PWM5
PWM6
PWM7
PWM8
PWM9
PWM10
PWM11
PWM12
PWM13
PWM14
PWM15
$00
$01
$02
$03
$04
$05
$06
$07
$08
$09
$0A
$0B
$0C
$0D
$0E
$0F
$10
$11
$12
$13
$14
$15
$16
$17
$18
$19
$1A
$1B
$1C
$1D
$1E
$1F
$20
$21
$22
$23
$24
$25
$26
$27
$28
$29
$2A
$2B
$2C
$2D
$2E
$2F
$3FFF
$3FF0
$3FF2
$3FF4
$3FF6
$3FF8
$3FFA
$3FFC
$3FFE
14
Reserved
Reserved
MFT
MBUS
SSP
IRQ
SWI
RESET
TPG
MOTOROLA
14-2
MC68HC705BD3
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
100
Freescale Semiconductor, Inc.
14.3.1
Programming Control Register (PCR)
The EPROM Programming Control register controls the actual programming of the EPROM in the
MC68HC705BD3.
Address
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
Freescale Semiconductor, Inc...
$001D
bit 1
bit 0
State
on reset
ELAT
PGM
---- --00
ELAT - EPROM Latch Control
1 (set)
–
0 (clear) –
EPROM address and data bus configured for programming (writes to
EPROM cause address data to be latched). EPROM is in
programming mode and cannot be read if ELAT is 1. This bit is not
able be set when no VPP voltage is applied to the VPP pin.
EPROM address and data bus configured for normal reads.
PGM - EPROM Program Command
1 (set)
–
0 (clear) –
14.3.2
Programming power switched on to EPROM array. If ELAT≠1 then
PGM=0.
Programming power switched off to EPROM array.
EPROM Programming Sequence
Programming the EPROM of the MC68HC705BD3 is as follows:
1) Set the ELAT bit.
2) Write the data to be programmed to the address to be programmed.
3) Set the PGM bit.
4) Delay for the appropriate amount of time.
5) Clear the PGM and the ELAT bits.
The last action may be carried out in a single CPU write operation. It is important to remember
that an external programming voltage must be applied to the VPP pin while programming, but
should be equal to VDD during normal operation.
Example shows address $2000 is programmed with $00.
CLR
LDX
BSET
LDA
STA
PCR
#$00
1,PCR
#$00
$2000,X
;reset PCR
;load index register with 00
;set ELAT bit
;load data=00 in to A
;latch data and address
14
TPG
MC68HC05BD3
MC68HC705BD3
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
14-3
101
Freescale Semiconductor, Inc.
BSET
JSR
CLR
0,PCR
DELAY
PCR
14.4
;program
;call delay subroutine
;reset PCR
DC Electrical Characteristics
Freescale Semiconductor, Inc...
Table 14-2 DC Electrical Characteristics for MC68HC705BD3
(VDD =5.0Vdc ±10%, VSS =0Vdc, temperature range=0 to 70°C)
CHARACTERISTICS
SYMBOL
MINIMUM
Output voltage
ILOAD = –10µA
VOH
VDD-0.1
ILOAD = +10µA
VOL
–
Output high voltage (ILOAD=–5mA)
VOH
VDD-0.8
PA0-PA7, PB0-PB1, PC6-PC7, PD0-PD1
Output low voltage (ILOAD=+5mA)
PA0-PA7, PB0-PB5, PC0-PC7, PD0-PD1,
VOL
–
PWM0-PWM7
Input high voltage
PA0-PA7, PB0-PB5, PC0-PC7, PD0-PD1,
VIH
0.7xVDD
IRQ, RESET, EXTAL
2.0
VSYNC, HSYNC (TTL level)
Input low voltage
PA0-PA7, PB0-PB5, PC0-PC7, PD0-PD1,
VIL
VSS
IRQ, RESET, EXTAL
VSS
VSYNC, HSYNC (TTL level)
Supply current:
Run
IDD
–
Wait
–
I/O ports high-Z leakage current
PA0-PA7, PB0-PB5, PC0-PC7, PD0-PD1,
IIL
–
PWM0-PWM7
Input current
IIN
–
IRQ, RESET, EXTAL, VSYNC, HSYNC
Capacitance
COUT
–
ports (as input or output), RESET, IRQ,
CIN
–
EXTAL, XTAL, HSYNC, VSYNC
Notes:
(1) All values shown reflect average measurements.
TYPICAL
MAXIMUM
UNIT
–
–
–
0.1
V
V
–
–
V
–
0.4
V
–
–
VDD
VDD
V
0.2xVDD
0.8
V
6
2
20
8
mA
mA
–
±10
µA
–
1
µA
–
–
12
8
pF
pF
–
–
(2) Typical values at midpoint of voltage range, 25°C only.
(3) Wait IDD: only timer system and SSP is active.
14
(4) Run (operating) IDD, Wait IDD: measured using external square wave clock source to EXTAL (fOSC =4.2MHz),
all inputs 0.2 Vdc from rail; no dc loads, less than 50pF on all outputs, CL =20pF on EXTAL.
(5) Wait IDD: all ports configured as inputs, VIL =0.2 Vdc, VIH =VDD – 0.2 Vdc.
(6) Wait IDD is affected linearly by the EXTAL capacitance.
TPG
MOTOROLA
14-4
MC68HC705BD3
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
102
Freescale Semiconductor, Inc.
15
Freescale Semiconductor, Inc...
MC68HC05BD5
The MC68HC05BD5 is functionally equivalent to MC68HC05BD3, but with increased RAM size of
256 bytes and ROM size of 7.75K-bytes. The entire MC68HC05BD3 data sheet applies to the
MC68HC05BD5, with exceptions outlined in the section.
15.1
Features
•
Functionally equivalent to MC68HC05BD3
•
256 bytes on-chip RAM
•
7.75K-bytes user ROM
15.2
Memory Map
Figure 15-1 shows the memory map for the MC68HC05BD5.
TPG
MC68HC05BD3
MC68HC05BD5
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
15-1
15
103
Freescale Semiconductor, Inc.
MC68HC05BD5
$0000
$002F
$0030
I/O
48 Bytes
Unused
$007F
$0080
$00C0
Freescale Semiconductor, Inc...
$00FF
Stack
64 Bytes
User RAM
256 Bytes
$017F
$0180
Unused
$1FFF
$2000
User ROM
7936 Bytes
$3EFF
$3F00
$3FDF
$3FE0
$3FEF
$3FF0
$3FFF
Self-Check
Program
224 Bytes
Self-Check
Vectors
16 Bytes
User Vectors
16 Bytes
Port A Data Register
Port B Data Register
Port C Data Register
Port D Data Register
Port A Data Direction Register
Port B Data Direction Register
Port C Data Direction Register
Port D Data Direction Register
MFT Control and Status Register
MFT Timer Counter Register
Configuration Register 1
Configuration Register 2
SSP Control and Status Register
Vertical Frequency High Register
Vertical Frequency Low Register
Line Frequency High Register
Line Frequency Low Register
Sync Signal Control Register
Unused
Unused
Unused
Unused
Unused
MBUS Address Register
MBUS Frequency Divider Register
MBUS Control Register
MBUS Status Register
MBUS Data Register
Unused
Reserved
HSYNC Period Width Register
Reserved
PWM0
PWM1
PWM2
PWM3
PWM4
PWM5
PWM6
PWM7
PWM8
PWM9
PWM10
PWM11
PWM12
PWM13
PWM14
PWM15
$3FF0
$3FF2
$3FF4
$3FF6
$3FF8
$3FFA
$3FFC
$3FFE
15
$00
$01
$02
$03
$04
$05
$06
$07
$08
$09
$0A
$0B
$0C
$0D
$0E
$0F
$10
$11
$12
$13
$14
$15
$16
$17
$18
$19
$1A
$1B
$1C
$1D
$1E
$1F
$20
$21
$22
$23
$24
$25
$26
$27
$28
$29
$2A
$2B
$2C
$2D
$2E
$2F
Reserved
Reserved
MFT
MBUS
SSP
IRQ
SWI
RESET
TPG
MOTOROLA
15-2
MC68HC05BD5
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
104
Freescale Semiconductor, Inc.
15.3
DC Electrical Characteristics
Freescale Semiconductor, Inc...
Table 15-1 DC Electrical Characteristics for MC68HC05BD5
(VDD =5.0Vdc ±10%, VSS =0Vdc, temperature range=0 to 70°C)
CHARACTERISTICS
SYMBOL
MINIMUM
Output voltage
ILOAD = –10µA
VOH
VDD-0.1
ILOAD = +10µA
VOL
–
Output high voltage (ILOAD=–5mA)
VOH
VDD-0.8
PA0-PA7, PB0-PB1, PC6-PC7, PD0-PD1
Output low voltage (ILOAD=+5mA)
PA0-PA7, PB0-PB5, PC0-PC7, PD0-PD1,
VOL
–
PWM0-PWM7
Input high voltage
PA0-PA7, PB0-PB5, PC0-PC7, PD0-PD1,
VIH
0.7xVDD
IRQ, RESET, EXTAL
2.0
VSYNC, HSYNC (TTL level)
Input low voltage
PA0-PA7, PB0-PB5, PC0-PC7, PD0-PD1,
VIL
VSS
IRQ, RESET, EXTAL
VSS
VSYNC, HSYNC (TTL level)
Supply current:
Run
IDD
–
Wait
–
I/O ports high-Z leakage current
PA0-PA7, PB0-PB5, PC0-PC7, PD0-PD1,
IIL
–
PWM0-PWM7
Input current
IIN
–
IRQ, RESET, EXTAL, VSYNC, HSYNC
Capacitance
COUT
–
ports (as input or output), RESET, IRQ,
CIN
–
EXTAL, XTAL, HSYNC, VSYNC
Notes:
(1) All values shown reflect average measurements.
TYPICAL
MAXIMUM
UNIT
–
–
–
0.1
V
V
–
–
V
–
0.4
V
–
–
VDD
VDD
V
0.2xVDD
0.8
V
7
1.3
20
8
mA
mA
–
±10
µA
–
1
µA
–
–
12
8
pF
pF
–
–
(2) Typical values at midpoint of voltage range, 25°C only.
(3) Wait IDD: only timer system and SSP is active.
(4) Run (operating) IDD, Wait IDD: measured using external square wave clock source to EXTAL (fOSC =4.2MHz),
all inputs 0.2 Vdc from rail; no dc loads, less than 50pF on all outputs, CL =20pF on EXTAL.
(5) Wait IDD: all ports configured as inputs, VIL =0.2 Vdc, VIH =VDD – 0.2 Vdc.
(6) Wait IDD is affected linearly by the EXTAL capacitance.
TPG
MC68HC05BD3
MC68HC05BD5
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
15-3
15
105
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
THIS PAGE LEFT BLANK INTENTIONALLY
15
TPG
MOTOROLA
15-4
MC68HC05BD5
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3
106
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
GENERAL DESCRIPTION
1
PIN DESCRIPTION AND I/O PORTS
2
MEMORY AND REGISTERS
3
RESETS AND INTERRUPTS
4
MULTI-FUNCTION TIMER
5
PULSE WIDTH MODULATION
6
M-BUS SERIAL INTERFACE
7
SYNC SIGNAL PROCESSOR
8
CPU CORE AND INSTRUCTION SET
9
LOW POWER MODES
10
OPERATING MODES
11
ELECTRICAL SPECIFICATIONS
12
MECHANICAL SPECIFICATIONS
13
MC68HC705BD3
14
TPG
MC68HC05BD5
For More Information On This Product,
Go to: www.freescale.com
15
107
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
1
GENERAL DESCRIPTION
2
PIN DESCRIPTION AND I/O PORTS
3
MEMORY AND REGISTERS
4
RESETS AND INTERRUPTS
5
MULTI-FUNCTION TIMER
6
PULSE WIDTH MODULATION
7
M-BUS SERIAL INTERFACE
8
SYNC SIGNAL PROCESSOR
9
CPU CORE AND INSTRUCTION SET
10
LOW POWER MODES
11
OPERATING MODES
12
ELECTRICAL SPECIFICATIONS
13
MECHANICAL SPECIFICATIONS
14
MC68HC705BD3
15
MC68HC05BD5
For More Information On This Product,
Go to: www.freescale.com
TPG
108
Freescale Semiconductor, Inc.
1
2
3
Freescale Semiconductor, Inc...
4
5
6
7
8
9
10
11
12
13
14
15
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
1
2
3
Freescale Semiconductor, Inc...
4
5
6
7
8
9
10
11
12
13
14
How to reach us:
MFAX: [email protected] – TOUCHTONE (602) 244-6609
INTERNET: http://Design-NET.com
USA/EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, Toshikatsu Otsuki, 6F Seibu-Butsuryu-Center,
3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-3521-8315
HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road,
Tai Po, N.T., Hong Kong. 852-26629298
15 !MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
MC68HC05BD3D/H
Similar pages