Freescale MC68HC08JK8CDW Microcontroller Datasheet

Freescale Semiconductor, Inc.
Addendum
HC908JL8AD/D
Rev. 0, 5/2002
Freescale Semiconductor, Inc...
Addendum to
MC68HC908JL8
Technical Data
This addendum provides update and additional information to the
MC68HC908JL8 Technical Data, Rev. 2
(Motorola document number MC68HC908JL8/D)
MC68HC08JL8
MC68HC08JK8
The MC68HC08JL8 is the ROM part equivalent to the MC68HC908JL8. The
entire MC68HC908JL8 data book apply to this ROM device, with exceptions
outlined in this addendum.
Table 1. Summary of MC68HC08JL8 and MC68HC908JL8 Differences
MC68HC08JL8
MC68HC908JL8
Memory ($DC00–$FBFF)
8,192 bytes ROM
8,192 bytes FLASH
User vectors ($FFDC–$FFFF)
36 bytes ROM
36 bytes FLASH
Registers at $FE08 and $FFCF
Not used;
locations are reserved.
FLASH related registers.
$FE08 — FLCR
$FFCF — FLBPR
Mask option register ($FFD0)
Defined by mask; read only.
Read/write FLASH register.
Monitor ROM
($FC00–$FDFF and $FE10–$FFCE)
$FC00–$FDFF: Not used.
$FE10–$FFCE: Used for
testing purposes only.
Used for testing and FLASH
programming/erasing.
Available Packages
20-pin PDIP (MC68HC08JK8)
20-pin SOIC (MC68HC08JK8)
28-pin PDIP
28-pin SOIC
32-pin SDIP
32-pin LQFP
20-pin PDIP (MC68HC908JK8)
20-pin SOIC (MC68HC908JK8)
28-pin PDIP
28-pin SOIC
32-pin SDIP
32-pin LQFP
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
HC908JL8AD/D
MCU Block Diagram
Figure 1 shows the block diagram of the MC68HC08JL8.
Memory Map
The MC68HC08JL8 has 8,192 bytes of user ROM from $DC00 to $FBFF, and
36 bytes of user ROM vectors from $FFDC to $FFFF. On the MC68HC908JL8,
these memory locations are FLASH memory.
Figure 2 shows the memory map of the MC68HC08JL8.
INTERNAL BUS
USER ROM — 8,192 BYTES
PORTA
CONTROL AND STATUS REGISTERS — 64 BYTES
PTA7/KBI7**‡
PTA6/KBI6**¥
PTA5/KBI5**‡
PTA4/KBI4**‡
PTA3/KBI3**‡
PTA2/KBI2**‡
PTA1/KBI1**‡
PTA0/KBI0**‡
PORTB
ARITHMETIC/LOGIC
UNIT (ALU)
PTB7/ADC7
PTB6/ADC6
PTB5/ADC5
PTB4/ADC4
PTB3/ADC3
PTB2/ADC2
PTB1/ADC1
PTB0/ADC0
KEYBOARD INTERRUPT
MODULE
8-BIT ANALOG-TO-DIGITAL
CONVERTER MODULE
DDRA
CPU
REGISTERS
2-CHANNEL TIMER INTERFACE
MODULE 1
2-CHANNEL TIMER INTERFACE
MODULE 2
MONITOR ROM — 447 BYTES
BREAK
MODULE
USER ROM VECTORS — 36 BYTES
RC OSCILLATOR
INTERNAL OSCILLATOR
POWER-ON RESET
MODULE
* RST
SYSTEM INTEGRATION
MODULE
LOW-VOLTAGE INHIBIT
MODULE
* IRQ
EXTERNAL INTERRUPT
MODULE
VDD
POWER
VSS
ADC REFERENCE
COMPUTER OPERATING
PROPERLY MODULE
PORTD
OSC2/RCCLK
ADC12/T2CLK
SERIAL COMMUNICATIONS
INTERFACE MODULE
PTE
¥
CRYSTAL OSCILLATOR
DDRD
OSC1
DDRB
USER RAM — 256 BYTES
DDRE
Freescale Semiconductor, Inc...
M68HC08 CPU
* Pin contains integrated pull-up device.
** Pin contains programmable pull-up device.
† 25mA open-drain if output pin.
‡ LED direct sink pin.
¥ Shared pin: OSC2/RCCLK/PTA6/KBI6.
# Pins available on 32-pin packages only.
## Pins available on 28-pin and 32-pin packages only.
Shaded blocks indicate differences to MC68HC908JL8
Figure 1. MC68HC08JL8 Block Diagram
Addendum to MC68HC908JL8 Technical Data
For More Information On This Product,
Go to: www.freescale.com
PTD7/RxD**†‡
PTD6/TxD**†‡
PTD5/T1CH1
PTD4/T1CH0
PTD3/ADC8‡
PTD2/ADC9‡
PTD1/ADC10
PTD0/ADC11
#
##
#
##
PTE1/T2CH1
#
PTE0/T2CH0
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
HC908JL8AD/D
MC68HC08JL8 MC68HC08JK8
$0000
↓
$003F
I/O REGISTERS
64 BYTES
$0040
↓
$005F
RESERVED
32 BYTES
$0060
↓
$015F
RAM
256 BYTES
$0160
↓
$DBFF
UNIMPLEMENTED
55,968 BYTES
$DC00
↓
$FBFF
ROM
8,192 BYTES
$FC00
↓
$FDFF
UNIMPLEMENTED
512 BYTES
$FE00
BREAK STATUS REGISTER (BSR)
$FE01
RESET STATUS REGISTER (RSR)
$FE02
RESERVED
$FE03
BREAK FLAG CONTROL REGISTER (BFCR)
$FE04
INTERRUPT STATUS REGISTER 1 (INT1)
$FE05
INTERRUPT STATUS REGISTER 2 (INT2)
$FE06
INTERRUPT STATUS REGISTER 3 (INT3)
$FE07
RESERVED
$FE08
RESERVED
$FE09
↓
$FF0B
RESERVED
$FE0C
BREAK ADDRESS HIGH REGISTER (BRKH)
$FE0D
BREAK ADDRESS LOW REGISTER (BRKL)
$FE0E
BREAK STATUS AND CONTROL REGISTER (BRKSCR)
$FE0F
RESERVED
$FE10
↓
$FFCE
MONITOR ROM
447 BYTES
$FFCF
RESERVED
$FFD0
MASK OPTION REGISTER (MOR) — READ ONLY
$FFD1
↓
$FFDB
RESERVED
11 BYTES
$FFDC
↓
$FFFF
USER ROM VECTORS
36 BYTES
Figure 2. MC68HC08JL8 Memory Map
Addendum to MC68HC908JL8 Technical Data
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
HC908JL8AD/D
Reserved Registers
The two registers at $FE08 and $FFCF are reserved locations on the
MC68HC08JL8.
On the MC68HC908JL8, these two locations are the FLASH control register
and the FLASH block protect register respectively.
Mask Option
Register
The mask option register at $FFD0 is read only. The value is defined by mask
option (hard-wired connections) specified at the time as the ROM code
submission.
Freescale Semiconductor, Inc...
On the MC68HC908JL8, the MOR is implemented as a FLASH, which can be
programmed, erased, and read.
Monitor ROM
The monitor program (monitor ROM: $FE10–$FFCE) on the MC68HC08JL8 is
for device testing only. $FC00–$FDFF are unused.
Electrical
Specifications
Electrical specifications for the MC68HC908JL8 apply to the MC68HC08JL8,
except for the parameters indicated below.
DC Electrical
Characteristics
Table 2. DC Electrical Characteristics (5V)
Characteristic(1)
Symbol
VDD supply current, fOP = 8MHz
RC oscillator option
IDD
Typ(2)
Min
Max
Unit
Values same as, and characterized from
MC68HC908JL8, but not tested.
Low-voltage inhibit, trip falling voltage
VTRIPF
3.55 (3.60)(3)
4.02 (4.25)
4.48 (4.48)
V
Low-voltage inhibit, trip rising voltage
VTRIPR
3.66 (3.75)
4.13 (4.40)
4.59 (4.63)
V
Max
Unit
1. VDD = 4.5 to 5.5 Vdc, VSS = 0 Vdc, TA = TL to TH, unless otherwise noted.
2. Typical values reflect average measurements at midpoint of voltage range, 25 °C only.
3. The numbers in parenthesis are MC68HC908JL8 values.
Table 3. DC Electrical Characteristics (3V)
Characteristic(1)
Symbol
VDD supply current, fOP = 4MHz
RC oscillator option
IDD
Low-voltage inhibit, trip voltage
(No hysteresis implemented for 3V LVI)
VLVI3
Typ(2)
Min
Values same as, and characterized from
MC68HC908JL8, but not tested.
2.1 (2.18)(3)
2.4 (2.49)
1. VDD = 2.7 to 3.3 Vdc, VSS = 0 Vdc, TA = TL to TH, unless otherwise noted.
2. Typical values reflect average measurements at midpoint of voltage range, 25 °C only.
3. The numbers in parenthesis are MC68HC908JL8 values.
Addendum to MC68HC908JL8 Technical Data
For More Information On This Product,
Go to: www.freescale.com
2.69 (2.68)
V
Freescale Semiconductor, Inc.
HC908JL8AD/D
MC68HC08JL8 MC68HC08JK8
RC frequency, fRCCLK (MHz)
12
CEXT = 10 pF
10
MCU
5V @ 25 °C
OSC1
8
6
VDD
4
REXT
CEXT
MC68HC908JL8
MC68HC08JL8
2
0
0
10
20
30
Resistor, REXT (kΩ)
40
50
Figure 3. RC vs. Frequency (5V @25 °C)
14
RC frequency, fRCCLK (MHz)
Freescale Semiconductor, Inc...
14
12
CEXT = 10 pF
10
MCU
3V @ 25 °C
OSC1
8
6
VDD
REXT
4
CEXT
MC68HC908JL8
MC68HC08JL8
2
0
0
10
20
30
Resistor, REXT (kΩ)
40
50
Figure 4. RC vs. Frequency (3V @25 °C)
Memory
Characteristics
Table 4. Memory Characteristics
Characteristic
RAM data retention voltage
Symbol
Min
Max
Unit
VRDR
1.3
—
V
Notes:
Since MC68HC08JL8 is a ROM device, FLASH memory electrical characteristics do not apply.
Addendum to MC68HC908JL8 Technical Data
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
HC908JL8AD/D
MC68HC08JL8
Order Numbers
These part numbers are generic numbers only. To place an order, ROM code
must be submitted to the ROM Processing Center (RPC).
Table 5. MC68HC08JL8 Order Numbers
Freescale Semiconductor, Inc...
MC Order Number
Operating
Temperature Range
MC68HC08JK8CP
–40 °C to +85 °C
MC68HC08JK8MP
–40 °C to +125 °C
MC68HC08JK8CDW
–40 °C to +85 °C
MC68HC08JK8MDW
–40 °C to +125 °C
MC68HC08JL8CP
–40 °C to +85 °C
MC68HC08JL8MP
–40 °C to +125 °C
MC68HC08JL8CDW
–40 °C to +85 °C
MC68HC08JL8MDW
–40 °C to +125 °C
MC68HC08JL8CSP
–40 °C to +85 °C
MC68HC08JL8MSP
–40 °C to +125 °C
MC68HC08JL8CFA
–40 °C to +85 °C
MC68HC08JL8MFA
–40 °C to +125 °C
NOTE: Temperature grade "M" is available for VDD = 5V only.
Addendum to MC68HC908JL8 Technical Data
For More Information On This Product,
Go to: www.freescale.com
Package
20-pin PDIP
20-pin SOIC
28-pin PDIP
28-pin SOIC
32-pin SDIP
32-pin LQFP
Freescale Semiconductor, Inc.
HC908JL8AD/D
AMENDMENTS TO MC68HC908JL8/D, REV. 2
AMENDMENTS TO MC68HC908JL8/D, REV. 2
Keyboard Interrupt
Page 243, Figure 15-2. Keyboard Interrupt Block Diagram — Replace with
the following block diagram:
INTERNAL BUS
Freescale Semiconductor, Inc...
NOTE:
To prevent false interrupts, user should use software
to debounce keyboard interrupt inputs.
KBI0
ACKK
VDD
VECTOR FETCH
DECODER
KEYF
RESET
.
KBIE0
D
CLR
Q
SYNCHRONIZER
.
CK
TO PULLUP ENABLE
.
KEYBOARD
INTERRUPT FF
KBI7
KEYBOARD
INTERRUPT
REQUEST
IMASKK
MODEK
KBIE7
TO PULLUP ENABLE
Computer Operating
Properly (COP)
From:
Page 254, 16.8.2 Stop Mode — Replace the two paragraphs:
Stop mode turns off the ICLK input to the COP if the STOP_ICLKDIS bit is set
in configuration register 2 (CONFIG2). Service the COP immediately before
entering or after exiting stop mode to ensure a full COP timeout period after
entering or exiting stop mode.
After reset, the STOP_ICLKDIS bit is clear by default and ICLK is enabled
during stop mode.
To:
Stop mode turns off the ICLK input to the COP and clears the COP prescaler.
Service the COP immediately before entering or after exiting stop mode to
ensure a full COP timeout period after entering or exiting stop mode.
To prevent inadvertently turning off the COP with a STOP instruction, a
configuration option is available that disables the STOP instruction. When the
STOP bit in the configuration register has the STOP instruction is disabled,
execution of a STOP instruction results in an illegal opcode reset.
Addendum to MC68HC908JL8 Technical Data
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Home Page:
www.freescale.com
email:
[email protected]
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
(800) 521-6274
480-768-2130
[email protected]
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku
Tokyo 153-0064, Japan
0120 191014
+81 2666 8080
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate,
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
For Literature Requests Only:
Freescale Semiconductor
Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
(800) 441-2447
303-675-2140
Fax: 303-675-2150
LDCForFreescaleSemiconductor
@hibbertgroup.com
RoHS-compliant and/or Pb- free versions of Freescale products have the functionality
and electrical characteristics of their non-RoHS-compliant and/or non-Pb- free
counterparts. For further information, see http://www.freescale.com or contact your
Freescale sales representative.
For information on Freescale.s Environmental Products program, go to
http://www.freescale.com/epp.
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters which may be
provided in Freescale Semiconductor data sheets and/or specifications can and do
vary in different applications and actual performance may vary over time. All operating
parameters, including “Typicals” must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters which may be
provided in Freescale Semiconductor data sheets and/or specifications can and do
vary in different applications and actual performance may vary over time. All operating
parameters, including “Typicals” must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
HC908JL8AD/D
Rev. 0
5/2003
For More Information On This Product,
Go to: www.freescale.com