ON MC74LVXT4051D Analog multiplexer demultiplexer high-performance silicon-gate cmo Datasheet

MC74LVXT4051
Analog Multiplexer/
Demultiplexer
High–Performance Silicon–Gate CMOS
The MC74LVXT4051 utilizes silicon–gate CMOS technology to
achieve fast propagation delays, low ON resistances, and low leakage
currents. This analog multiplexer/demultiplexer controls analog
voltages that may vary across the complete power supply range (from
VCC to VEE).
The LVXT4051 is similar in pinout to the LVX8051, the HC4051A,
and the metal–gate MC14051B. The Channel–Select inputs determine
which one of the Analog Inputs/Outputs is to be connected, by means
of an analog switch, to the Common Output/Input. When the Enable
pin is HIGH, all analog switches are turned off.
The Channel–Select and Enable inputs are compatible with standard
TTL levels. These inputs are over–voltage tolerant (OVT) for level
translation from 6.0 V down to 3.0 V.
This device has been designed so the ON resistance (RON) is more
linear over input voltage than the RON of metal–gate CMOS analog
switches and High–Speed CMOS analog switches.
•
•
•
•
•
•
MARKING DIAGRAMS
16
9
LVXT4051
AWLYYWW
SO–16
D SUFFIX
CASE 751B
1
8
16
9
LVXT
4051
AWLYWW
TSSOP–16
DT SUFFIX
CASE 948F
1
8
Select Pins Compatible with TTL Levels
Fast Switching and Propagation Speeds
16
Low Crosstalk Between Switches
Analog Power Supply Range (VCC – VEE) = 3.0 V to 3.0 V
Digital (Control) Power Supply Range (VCC – GND) = 2.5 to 6.0 V
Improved Linearity and Lower ON Resistance Than Metal–Gate,
HSL, or VHC Counterparts
Low Noise
•
• Designed to Operate on a Single Supply with VEE = GND, or Using
•
http://onsemi.com
Split Supplies up to 3.0 V
Break–Before–Make Circuitry
LVXT4051
ALYW
SO EIAJ–16
M SUFFIX
CASE 966
A
L, WL
Y, YY
W, WW
9
1
8
= Assembly Location
= Wafer Lot
= Year
= Work Week
ORDERING INFORMATION
Device
 Semiconductor Components Industries, LLC, 2002
January, 2002 – Rev. 3
1
Package
Shipping
MC74LVXT4051D
SO–16
48 Units/Rail
MC74LVXT4051DR2
SO–16
2500 Units/Reel
MC74LVXT4051DT
TSSOP–16
96 Units/Rail
MC74LVXT4051DTR2
TSSOP–16
2500 Units/Reel
MC74LVXT4051M
SO EIAJ–16
48 Units/Rail
MC74LVXT4051MEL
SO EIAJ–16
2000 Units/Reel
Publication Order Number:
MC74LVXT4051/D
MC74LVXT4051
FUNCTION TABLE
VCC
X2
X1
X0
X3
A
B
C
16
15
14
13
12
11
10
9
1
X4
2
X6
3
X
4
X7
Control Inputs
Enable
C
L
L
L
L
L
L
L
L
H
L
L
L
L
H
H
H
H
X
5
6
7
8
X5 Enable VEE GND
Figure 1. Pin Connection and Marking Diagram
(Top View)
Select
B
A
L
L
H
H
L
L
H
H
X
X = Don’t Care
Single–Pole, 8–Position Plus Common Off
X0
X1
X2
ANALOG
INPUTS/OUTPUTS
13
14
15
3
X3 12
1
X4
5
X5
X6 2
X7
MULTIPLEXER/
DEMULTIPLEXER
4
A 11
10
B
9
C
6
ENABLE
CHANNEL
SELECT INPUTS
PIN 16 = VCC
PIN 8 = GND
PIN 7 = VEE
Figure 2. Logic Diagram
http://onsemi.com
2
X
COMMON
OUTPUT/INPUT
L
H
L
H
L
H
L
H
X
ON Channels
X0
X1
X2
X3
X4
X5
X6
X7
NONE
MC74LVXT4051
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
Î
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
MAXIMUM RATINGS (Note 1)
Symbol
Parameter
Value
Unit
7.0 to 0.5
0.5 to 7.0
0.5 to 7.0
V
VEE 0.5 to VCC 0.5
V
0.5 to 7.0
V
VEE
Negative DC Supply Voltage
(Referenced to GND)
VCC
Positive DC Supply Voltage
(Referenced to GND)
(Referenced to VEE)
VIS
Analog Input Voltage
VIN
Digital Input Voltage
I
DC Current, Into or Out of Any Pin
TSTG
Storage Temperature Range
TL
Lead Temperature, 1 mm from Case for 10 Seconds
TJ
Junction Temperature under Bias
JA
Thermal Resistance
PD
Power Dissipation in Still Air,
MSL
Moisture Sensitivity
FR
Flammability Rating
VESD
ESD Withstand Voltage
Human Body Model (Note 2)
Machine Model (Note 3)
Charged Device Model (Note 4)
2000
200
1000
V
ILATCH–UP
Latch–Up Performance
Above VCC and Below GND at 125°C (Note 5)
300
mA
(Referenced to GND)
V
20
mA
65 to 150
C
260
C
150
C
SOIC
TSSOP
143
164
°C/W
SOIC
TSSOP
500
450
mW
Level 1
Oxygen Index: 30% – 35%
UL–94–VO (0.125 in)
1. Absolute maximum continuous ratings are those values beyond which damage to the device may occur. Extended exposure to these
conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute maximum–rated
conditions is not implied.
2. Tested to EIA/JESD22–A114–A.
3. Tested to EIA/JESD22–A115–A.
4. Tested to JESD22–C101–A.
5. Tested to EIA/JESD78.
RECOMMENDED OPERATING CONDITIONS
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
Min
Max
Unit
VEE
Symbol
Negative DC Supply Voltage
Parameter
(Referenced to GND)
6.0
GND
V
VCC
Positive DC Supply Voltage
(Referenced to GND)
(Referenced to VEE)
2.5
2.5
6.0
6.0
V
VIS
Analog Input Voltage
VEE
VCC
V
VIN
Digital Input Voltage
TA
Operating Temperature Range, All Package Types
tr, tf
Input Rise/Fall Time
(Channel Select or Enable Inputs)
(Note 6) (Referenced to GND)
0
6.0
V
55
125
C
0
0
100
20
ns/V
VCC = 3.0 V 0.3 V
VCC = 5.0 V 0.5 V
6. Unused inputs may not be left open. All inputs must be tied to a high–logic voltage level or a low–logic input voltage level.
90
419,300
47.9
100
178,700
20.4
110
79,600
9.4
120
37,000
4.2
130
17,800
2.0
140
8,900
1.0
TJ = 80C
117.8
TJ = 90C
1,032,200
TJ = 100C
80
TJ = 110C
Time, Years
TJ = 120C
Time, Hours
FAILURE RATE OF PLASTIC = CERAMIC
UNTIL INTERMETALLICS OCCUR
TJ = 130C
Junction
Temperature °C
NORMALIZED FAILURE RATE
DEVICE JUNCTION TEMPERATURE VERSUS
TIME TO 0.1% BOND FAILURES
1
1
10
100
1000
TIME, YEARS
Figure 3. Failure Rate vs. Time Junction Temperature
http://onsemi.com
3
MC74LVXT4051
DC CHARACTERISTICS – Digital Section (Voltages Referenced to GND)
VCC
V
Guaranteed Limit
55 to 25°C
85°C
125°C
Unit
VIH
Minimum High–Level Input Voltage,
Channel–Select or Enable Inputs
3.0
4.5
5.5
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
V
VIL
Maximum Low–Level Input Voltage,
Channel–Select or Enable Inputs
3.0
4.5
5.5
0.5
0.8
0.8
0.5
0.8
0.8
0.5
0.8
0.8
V
IIN
Maximum Input Leakage Current,
Channel–Select or Enable Inputs
VIN = 6.0 or GND
0 V to 6.0 V
0.1
1.0
1.0
A
ICC
Maximum Quiescent Supply
Current (per Package)
Channel Select, Enable and
VIS = VCC or GND
6.0
4.0
40
80
A
Symbol
Parameter
Condition
ÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎ
ÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎ
ÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎ
DC ELECTRICAL CHARACTERISTICS – Analog Section
Symbol
Parameter
Test Conditions
Guaranteed Limit
VCC
V
VEE
V
55 to 25°C
85C
125C
Unit
RON
Maximum “ON” Resistance
VIN = VIL or VIH
VIS = ½ (VCC – VEE)
|IS| = 2.0 mA
(Figure 4)
3.0
4.5
3.0
0
0
3.0
86
37
26
108
46
33
120
55
37
∆RON
Maximum Difference in “ON”
Resistance Between Any
Two Channels in the Same
Package
VIN = VIL or VIH
VIS = ½ (VCC – VEE)
|IS| = 2.0 mA
3.0
4.5
3.0
0
0
3.0
15
13
10
20
18
15
20
18
15
Maximum Off–Channel
Leakage Current, Any One
Channel
Vin = VIL or VIH;
VIO = VCC or GND;
Switch Off (Figure 3)
5.5
+3.0
0
–3.0
0.1
0.1
0.5
0.5
1.0
1.0
A
Maximum Off–Channel
Leakage Current,
Common Channel
Vin = VIL or VIH;
VIO = VCC or GND;
Switch Off (Figure 4)
5.5
+3.0
0
–3.0
0.2
0.2
2.0
2.0
4.0
4.0
Maximum On–Channel
Leakage Current,
Channel–to–Channel
Vin = VIL or VIH;
Switch–to–Switch =
VCC or GND; (Figure 5)
5.5
+3.0
0
–3.0
0.2
0.2
2.0
2.0
4.0
4.0
Ioff
Ion
A
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎ
AC CHARACTERISTICS (Input tr = tf = 3 ns)
Guaranteed Limit
Symbol
tBBM
Parameter
Minimum Break–Before–Make
Time
Test Conditions
VIN = VIL or VIH
VIS = VCC
RL = 300 CL = 35 pF
(Figures 12 and 13)
VEE
V
Min
Typ*
85C
125C
Unit
3.0
4.5
3.0
0.0
0.0
3.0
1.0
1.0
1.0
6.5
5.0
3.5
–
–
–
–
–
–
ns
*Typical Characteristics are at 25C.
http://onsemi.com
4
55 to 25C
VCC
V
MC74LVXT4051
AC CHARACTERISTICS (CL = 50 pF, Input tr = tf = 3 ns)
Guaranteed Limit
Symbol
Parameter
VCC
V
VEE
V
55 to 25°C
Min
Typ
85°C
Max
Min
125°C
Max
Min
Max
Unit
tPLH,
tPHL
Maximum Propagation Delay,
Channel–Select to Analog
Output
(Figures 16 and 17)
2.5
3.0
4.5
3.0
0
0
0
3.0
40
28
23
23
45
30
25
25
50
35
30
28
ns
tPLZ,
tPHZ
Maximum Propagation Delay,
Enable to Analog Output (Figures 14 and 15)
2.5
3.0
4.5
3.0
0
0
0
3.0
40
28
23
23
45
30
25
25
50
35
30
28
ns
tPZL,
tPZH
Maximum Propagation Delay,
Enable to Analog Output (Figures 14 and 15)
2.5
3.0
4.5
3.0
0
0
0
3.0
40
28
23
23
45
30
25
25
50
35
30
28
ns
CPD
Power Dissipation Capacitance (Figure 18) (Note 7)
45
pF
CIN
Maximum Input Capacitance, Channel–Select or Enable Inputs
10
pF
CI/O
Maximum Capacitance
(All Switches Off)
10
10
1.0
pF
Typical @ 25°C, VCC = 5.0 V, VEE = 0V
Analog I/O
Common O/I
Feedthrough
7. Used to determine the no–load dynamic power consumption: PD = CPD VCC
2f
+ ICC VCC .
ADDITIONAL APPLICATION CHARACTERISTICS (GND = 0 V)
Symbol
Parameter
Condition
Typ
VCC
V
VEE
V
25°C
Unit
BW
Maximum On–Channel
Bandwidth or Minimum
Frequency Response
VIS = ½ (VCC – VEE)
Ref and Test Attn = 10 dB
Source Amplitude = 0 dB
(Figure 7)
3.0
4.5
6.0
3.0
0.0
0.0
0.0
3.0
80
80
80
80
MHz
VISO
Off–Channel Feedthrough
Isolation
f = 1 MHz; VIS = ½ (VCC – VEE)
Adjust Network Analyzer output to 10 dBm on each
output from the power splitter.
(Figures 8 and 9)
3.0
4.5
6.0
3.0
0.0
0.0
0.0
3.0
70
70
70
70
dB
VONL
Maximum Feedthrough
On Loss
VIS = ½ (VCC – VEE)
Adjust Network Analyzer output to 10 dBm on each
output from the power splitter.
(Figure 11)
3.0
4.5
6.0
3.0
0.0
0.0
0.0
3.0
2
2
2
2
dB
Q
Charge Injection
VIN = VCC to VEE, fIS = 1 kHz, tr = tf = 3 ns
RIS = 0 , CL= 1000 pF, Q = CL * ∆VOUT
(Figure 10)
5.0
3.0
3.0
0.0
9.0
12
pC
THD
Total Harmonic Distortion
THD + Noise
fIS = 1 MHz, RL = 10 K, CL = 50 pF,
VIS = 5.0 VPP sine wave
VIS = 6.0 VPP sine wave
(Figure 19)
6.0
3.0
0.0
3.0
0.10
0.05
http://onsemi.com
5
%
MC74LVXT4051
PLOTTER
PROGRAMMABLE
POWER
SUPPLY
MINI
COMPUTER
DC ANALYZER
VCC
DEVICE
UNDER TEST
ANALOG IN
COMMON OUT
GND
GND
Figure 4. On Resistance, Test Set–Up
VCC
VCC
16
VEE
VCC
A
A
OFF
NC
VCC
COMMON O/I
OFF
VEE
VEE
6
7
8
Figure 5. Maximum Off Channel Leakage Current,
Any One Channel, Test Set–Up
HP4195A
Network Anl
S1 R1 T1
6
7
8
Figure 6. Maximum On Channel Leakage Current,
Channel to Channel, Test Set–Up
0.1 F
VIS
HP11667B
Pwr Splitter
VCC
100 K
0.1 F
ON
All untested Analog I/O pins
OFF
50 K
VEE
6
7
8
N/C
COMMON O/I
ANALOG I/O
VIL
VIH
VCC
ON
VEE
OFF
VCC
16
A
9 – 11
Channel Selects
connected to address
pins on HP4195A and
appropriately configured
to test each switch.
Figure 7. Maximum On Channel Bandwidth, Test Set–Up
http://onsemi.com
6
MC74LVXT4051
HP4195A
Network Anl
S1 R1 T1
0.1 F
HP11667B
Pwr Splitter
0.1 F
VIS
VCC
100 K
16
OFF
All untested Analog I/O pins
ON
50 K
VEE
6
7
8
Channel Selects
connected to address
pins on HP4195A and
appropriately configured
to test each switch.
9 – 11
Config = Network
Format = T/R (dB)
CAL = Trans Cal
VISO(dB) = 20 log (VT1/VR1)
Display = Rectan XAB
Scale Ref = Auto Scale
View = Off, Off, Off
Trig = Cont Mode
Source Amplitude = 13 dB
Reference Attenuation = 20 dB
Test Attenuation = 0 dB
Figure 8. Maximum Off Channel Feedthrough Isolation, Test Set–Up
HP4195A
Network Anl
S1 R1 T1
HP11667B
Pwr Splitter
0.1 F
VIS
VCC
100 K
0.1 F
16
OFF
ON
50 K
All untested Analog I/O pins
50 VEE
6
7
8
Config = Network
Format = T/R (dB)
CAL = Trans Cal
Display = Rectan XAB
Scale Ref = Auto Scale
View = Off, Off, Off
Trig = Cont Mode
Source Amplitude = 13 dB
Reference Attenuation = 20 dB
Test Attenuation = 0 dB
9 – 11
Channel Selects
connected to address
pins on HP4195A and
appropriately configured
to test each switch.
VISOC(dB) = 20 log (VT1/VR1)
Figure 9. Maximum Common–Channel Feedthrough Isolation, Test Set–Up
http://onsemi.com
7
MC74LVXT4051
VCC
16
ON/OFF
VOUT
OFF/ON
VIN
Enable
VEE
6
RIS
7
8
CL *
Bias Channel Selects to
test each combination of
analog inputs to common
analog output.
9 – 11
*Includes all probe and jig capacitance.
VIH
VIS
VIL
Q = CL * VOUT
VOUT
VOUT
Figure 10. Charge Injection, Test Set–Up
HP4195A
Network Anl
S1 R1 T1
0.1 F
HP11667B
Pwr Splitter
0.1 F
VIS
VCC
100 K
16
ON
All untested Analog I/O pins
OFF
50 VEE
6
7
8
Config = Network
Format = T/R (dB)
CAL = Trans Cal
Display = Rectan XAB
Scale Ref = Auto Scale
View = Off, Off, Off
Trig = Cont Mode
Source Amplitude = 13 dB
Reference Attenuation = 20 dB
Test Attenuation = 20 dB
9 – 11
Channel Selects
connected to address
pins on HP4195A and
appropriately configured
to test each switch.
VONL(dB) = 20 log (VT1/VR1)
Figure 11. Maximum On Channel Feedthrough On Loss, Test Set–Up
http://onsemi.com
8
MC74LVXT4051
Tek 11801B
DSO
COM INPUT
VCC
VCC
VIN
VOH
16
80%
OFF
ON
VEE
80% of
VOH
CL
RL
Channel Selects connected
to VIN and appropriately
configured to test each switch.
6
7
8
9 – 11
GND
tBBM
VIN
50 Figure 12. Break–Before–Make, Test Set–Up
Figure 13. Break–Before–Make Time
VCC
VCC
16
VCC
CHANNEL
SELECT
COMMON
O/I
TEST
POINT
ON/OFF
ANALOG I/O
50%
OFF/ON
GND
tPLH
ANALOG
OUT
CL *
6
7
8
tPHL
50%
CHANNEL SELECT
*Includes all probe and jig capacitance.
Figure 14. Propagation Delays, Channel Select
to Analog Out
tf
GND
POSITION 1 WHEN TESTING tPHZ AND tPZH
1
POSITION 2 WHEN TESTING tPLZ AND tPZL
tr
90%
50%
10%
ENABLE
tPZL
ANALOG
OUT
tPLZ
VCC
2
GND
HIGH
IMPEDANCE
10%
tPHZ
90%
VCC
VCC
16
1
50%
tPZH
ANALOG
OUT
Figure 15. Propagation Delay, Test Set–Up
Channel Select to Analog Out
ANALOG I/O
ON/OFF
2
VOL
1 KΩ
TEST
POINT
CL *
ENABLE
VOH
50%
HIGH
IMPEDANCE
Figure 16. Propagation Delays, Enable to
Analog Out
6
7
8
Figure 17. Propagation Delay, Test Set–Up
Enable to Analog Out
http://onsemi.com
9
MC74LVXT4051
VCC
A
VCC
ON/OFF
NC
OFF/ON
VIL
15
10 – 11,
13 – 14
12
Channel
Select
Figure 18. Power Dissipation Capacitance, Test Set–Up
HP3466
DMM
V
COM
HP3466
DMM
V
COM
HP E3630A
DC Pwr Supply
COM
20 V
HP 339
Distortion Measurement Set
20 V
Analyzer
Input COM
Oscillator
Output COM
16
ON
RL
OFF
50 K
6
7
8
9 – 11
CL
Channel Selects connected
to DC bias supply or ground
and appropriately configured
to test each switch.
Figure 19. Total Harmonic Distortion, Test Set–Up
http://onsemi.com
10
MC74LVXT4051
APPLICATIONS INFORMATION
outputs to VCC or GND through a low value resistor helps
minimize crosstalk and feedthrough noise that may be
picked up by an unused switch.
Although used here, balanced supplies are not a
requirement. The only constraints on the power supplies are
that:
VEE – GND = 0 to 6 volts
VCC – GND = 2.5 to 6 volts
VCC – VEE = 2.5 to 6 volts
and VEE GND
When voltage transients above VCC and/or below VEE are
anticipated on the analog channels, external Germanium or
Schottky diodes (Dx) are recommended as shown in
Figure 22. These diodes should be able to absorb the
maximum anticipated current surges during clipping.
The Channel Select and Enable control pins should be at
VCC or GND logic levels. VCC being recognized as a logic
high and GND being recognized as a logic low. In this
example:
VCC = 5 V = logic high
GND = 0 V = logic low
The maximum analog voltage swing is determined by the
supply voltages VCC and VEE. The positive peak analog
voltage should not exceed VCC. Similarly, the negative peak
analog voltage should not go below VEE. In this example,
the difference between VCC and VEE is five volts. Therefore,
using the configuration of Figure 21, a maximum analog
signal of five volts peak–to–peak can be controlled. Unused
analog inputs/outputs may be left floating (i.e., not
connected). However, tying unused analog inputs and
3.0 V
3.0 V
16
ANALOG
SIGNAL
3.0 V
3.0 V
6
7
8
3.0 V
ANALOG
SIGNAL
ON
11
10
9
5 V
5 V
3.0 V
16
ANALOG
SIGNAL
GND
TO EXTERNAL CMOS
CIRCUITRY 0 to 3.0 V
DIGITAL SIGNALS
6
7
8
Figure 20. Application Example
ANALOG
SIGNAL
ON
11
10
9
VCC
Dx
16
VCC
Dx
ON/OFF
Dx
Dx
VEE
VEE
VEE
7
8
Figure 22. External Germanium or Schottky Clipping Diodes
http://onsemi.com
11
GND
TO EXTERNAL CMOS
CIRCUITRY 0 to 5 V
DIGITAL SIGNALS
Figure 21. Application Example
VCC
5 V
MC74LVXT4051
A
11
13
LEVEL
SHIFTER
14
B
10
15
LEVEL
SHIFTER
12
C
9
1
LEVEL
SHIFTER
5
ENABLE
6
2
LEVEL
SHIFTER
4
3
Figure 23. Function Diagram, LVXT4051
http://onsemi.com
12
X0
X1
X2
X3
X4
X5
X6
X7
X
MC74LVXT4051
PACKAGE DIMENSIONS
SOIC–16
D SUFFIX
CASE 751B–05
ISSUE J
–A–
16
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
9
–B–
1
P
8 PL
0.25 (0.010)
8
M
B
S
G
R
K
F
X 45 C
–T–
SEATING
PLANE
J
M
D
16 PL
0.25 (0.010)
M
T B
S
A
S
http://onsemi.com
13
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0
7
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0
7
0.229
0.244
0.010
0.019
MC74LVXT4051
PACKAGE DIMENSIONS
TSSOP–16
DT SUFFIX
CASE 948F–01
ISSUE O
16X K REF
0.10 (0.004)
0.15 (0.006) T U
M
T U
V
S
S
S
ÇÇ
ÉÉ
ÇÇ
ÉÉ
ÇÇ
K
K1
2X
L/2
16
9
J1
B
–U–
L
SECTION N–N
J
PIN 1
IDENT.
8
1
N
0.15 (0.006) T U
S
0.25 (0.010)
A
–V–
M
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH.
PROTRUSIONS OR GATE BURRS. MOLD FLASH OR
GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER
SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED
0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE DETERMINED AT
DATUM PLANE -W-.
N
F
DETAIL E
–W–
C
0.10 (0.004)
–T– SEATING
PLANE
H
D
DETAIL E
G
http://onsemi.com
14
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
MILLIMETERS
MIN
MAX
4.90
5.10
4.30
4.50
--1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.18
0.28
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0
8
INCHES
MIN
MAX
0.193
0.200
0.169
0.177
--0.047
0.002
0.006
0.020
0.030
0.026 BSC
0.007
0.011
0.004
0.008
0.004
0.006
0.007
0.012
0.007
0.010
0.252 BSC
0
8
MC74LVXT4051
PACKAGE DIMENSIONS
SOIC EIAJ–16
M SUFFIX
CASE 966–01
ISSUE O
16
LE
9
Q1
M
E HE
1
8
L
DETAIL P
Z
D
e
VIEW P
A
DIM
A
A1
b
c
D
E
e
HE
L
LE
M
Q1
Z
A1
b
0.13 (0.005)
c
M
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS D AND E DO NOT INCLUDE MOLD
FLASH OR PROTRUSIONS AND ARE MEASURED
AT THE PARTING LINE. MOLD FLASH OR
PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006)
PER SIDE.
4. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
5. THE LEAD WIDTH DIMENSION (b) DOES NOT
INCLUDE DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08 (0.003)
TOTAL IN EXCESS OF THE LEAD WIDTH
DIMENSION AT MAXIMUM MATERIAL CONDITION.
DAMBAR CANNOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT. MINIMUM SPACE
BETWEEN PROTRUSIONS AND ADJACENT LEAD
TO BE 0.46 ( 0.018).
0.10 (0.004)
http://onsemi.com
15
MILLIMETERS
MIN
MAX
--2.05
0.05
0.20
0.35
0.50
0.18
0.27
9.90
10.50
5.10
5.45
1.27 BSC
7.40
8.20
0.50
0.85
1.10
1.50
10 0
0.70
0.90
--0.78
INCHES
MIN
MAX
--0.081
0.002
0.008
0.014
0.020
0.007
0.011
0.390
0.413
0.201
0.215
0.050 BSC
0.291
0.323
0.020
0.033
0.043
0.059
10 0
0.028
0.035
--0.031
MC74LVXT4051
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2700
Email: [email protected]
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
http://onsemi.com
16
MC74LVXT4051/D
Similar pages