MOTOROLA MCM62110FN15 32k x 9 bit synchronous dual i/o or separate i/o fast static ram with parity checker Datasheet

MOTOROLA
Order this document
by MCM62110/D
SEMICONDUCTOR TECHNICAL DATA
MCM62110
32K x 9 Bit Synchronous Dual I/O
or Separate I/O Fast Static RAM
with Parity Checker
• Single 5 V ± 10% Power Supply
• Choice of 5 V or 3.3 V ± 10% Power Supplies for Output Level
Compatibility
• Fast Access and Cycle Times: 15/17/20 ns Max
• Self–Timed Write Cycles
• Clock Controlled Output Latches
• Address, Chip Enable, and Data Input Registers
• Common Data Inputs and Data Outputs
• Dual I/O for Separate Processor and Memory Buses
• Separate Output Enable Controlled Three–State Outputs
• Odd Parity Checker During Reads
• Open Drain Output on Data Parity Error (DPE) Allowing Wire–ORing of
Outputs
• High Output Drive Capability: 85 pF/Output at Rated Access Time
• High Board Density 52 Lead PLCC Package
• Active High and Low Chip Enables for Easy Memory Depth Expansion
• Can be used as Separate I/O x9
FN PACKAGE
PLASTIC
CASE 778–02
SIE
PIE
SOE
POE
W
K
VCC
VSS
DPE
A6
A4
A2
A0
PIN ASSIGNMENT
7 6 5 4 3 2 1 52 51 50 49 48 47
8
46
9
45
10
44
11
43
12
42
13
41
14
40
15
39
16
38
17
37
18
36
19
35
20
34
21 22 23 24 25 26 27 28 29 30 31 32 33
A8
A7
A5
A3
A1
E2
E1
PDQ7
SDQ7
VSSQ
PDQ5
SDQ5
VCCQ
PDQ3
SDQ3
VSSQ
PDQ1
SDQ1
A14
A13
A12
A11
A10
VSS
VCC
A9
The MCM62110 is a 294,912 bit synchronous static random access memory
organized as 32,768 words of 9 bits, fabricated using Motorola’s high–performance silicon–gate CMOS technology. The device integrates a 32K x 9 SRAM
core with advanced peripheral circuitry consisting of address registers, two sets
of input data registers, two sets of output latches, active high and active low chip
enables, and a parity checker. The RAM checks odd parity during RAM read
cycles. The data parity error (DPE) output is an open drain type output which indicates the result of this check. This device has increased output drive capability
supported by multiple power pins. In addition, the output levels can be either 3.3 V
or 5 V TTL compatible by choice of the appropriate output bus power supply.
The device has both asynchronous and synchronous inputs. Asynchronous
inputs include the processor output enable (POE), system output enable (SOE), and
the clock (K).
The address (A0 – A14) and chip enable (E1 and E2) inputs are synchronous
and are registered on the falling edge of K. Write enable (W), processor input
enable (PIE) and system input enable (SIE) are registered on the rising edge
of K. Writes to the RAM are self–timed.
All data inputs/outputs, PDQ0 – PDQ7, SDQ0 – SDQ7, PDQP, and SDQP
have input data registers triggered by the rising edge of the clock. These pins also
have three–state output latches which are transparent during the high level of the
clock and latched during the low level of the clock.
This device has a special feature which allows data to be passed through the
RAM between the system and processor ports in either direction. This streaming
is accomplished by latching in data from one port and asynchronously output
enabling the other port. It is also possible to write to the RAM while streaming.
Additional power supply pins have been utilized for maximum performance. The
output buffer power (VCCQ) and ground pins (VSSQ) are electrically isolated from
VSS and VCC, and supply power and ground only to the output buffers. This allows
connecting the output buffers to 3.3 V instead of 5.0 V if desired. If 3.3 V output levels
are chosen, the output buffer impedance in the ‘‘high’’ state is approximately equal
to the impedance in the ‘‘low’’ state thereby allowing simplified transmission line terminations.
The MCM62110 is available in a 52–pin plastic leaded chip carrier (PLCC).
This device is ideally suited for pipelined systems and systems with multiple
data buses and multiprocessing systems, where a local processor has a bus isolated from a common system bus.
PIN NAMES
A0 – A14 . . . . . . . . . . . . . . . Address Inputs
K . . . . . . . . . . . . . . . . . . . . . . . . . Clock Input
W . . . . . . . . . . . . . . . . . . . . . . . Write Enable
E1 . . . . . . . . . . . . . Active Low Chip Enable
E2 . . . . . . . . . . . . . Active High Chip Enable
PIE . . . . . . . . . . . . . Processor Input Enable
SIE . . . . . . . . . . . . . . . System Input Enable
POE . . . . . . . . . . Processor Output Enable
SOE . . . . . . . . . . . . . System Output Enable
DPE . . . . . . . . . . . . . . . . . . Data Parity Error
PDQ0 – PDQ7 . . . . . . . Processor Data I/O
PDQP . . . . . . . . . . . Processor Data Parity
SDQ0 – SDQ7 . . . . . . . . . System Data I/O
SDQP . . . . . . . . . . . . . System Data Parity
VCC . . . . . . . . . . . . . . . + 5 V Power Supply
VCCQ . . . . . . Output Buffer Power Supply
VSSQ . . . . . . . . . . . . Output Buffer Ground
VSS . . . . . . . . . . . . . . . . . . . . . . . . . . Ground
All power supply and ground pins must be
connected for proper operation of the device.
VCC ≥ VCCQ at all times including power up.
REV 3
5/95
 Motorola, Inc. 1994
MOTOROLA
FAST SRAM
MCM62110
1
PDQP
SDQP
VSSQ
PDQ6
SDQ6
VCCQ
PDQ4
SDQ4
PDQ2
SDQ2
VSSQ
PDQ0
SDQ0
BLOCK DIAGRAM
DATA
REGISTER
K
PARITY
CHECK
A0 – A14
9
DATA
REGISTER
DATA
LATCH
WRITE
DRIVER
REGISTER
32K × 9 ARRAY
SENSE
AMPLIFIER
W
POE
PDQ0 – PDQ7, PDQP
CONTROL
DPE
9
DATA
REGISTER
DATA
LATCH
E1
E2
9
PIE
SOE
SDQ0 – SDQ7, SDQP
SIE
FUNCTIONAL TRUTH TABLE (See Notes 1 and 2)
W
PIE
SIE
POE
SOE
Mode
Memory Subsystem
Cycle
PDQ0 – PDQ7,
PDQP Output
SDQ0 – SDQ7,
SDQP Output
DPE
Notes
1
1
1
0
1
Read
Processor Read
Data Out
High–Z
Parity Out
3, 4
1
1
1
1
0
Read
Copy Back
High–Z
Data Out
Parity Out
3, 4
1
1
1
0
0
Read
Dual Bus Read
Data Out
Data Out
Parity Out
3, 4
1
X
X
1
1
Read
NOP
High–Z
High–Z
1
X
0
0
X
X
N/A
NOP
High–Z
High–Z
1
2, 5
0
0
1
1
1
Write
Processor Write Hit
Data In
High–Z
1
2, 6
0
1
0
1
1
Write
Allocate
High–Z
Data In
1
2
0
0
1
1
0
Write
Write Through
Data In
Stream Data
1
2, 7
0
1
0
0
1
Write
Allocate With Stream
Stream Data
Data In
1
2, 7
1
0
1
1
0
N/A
Cache Inhibit Write
Data In
Stream Data
1
2, 7
1
1
0
0
1
N/A
Cache Inhibit Read
Stream Data
Data In
1
2, 7
0
1
1
X
X
N/A
NOP
High–Z
High–Z
1
5
X
0
1
0
0
N/A
Invalid
Data In
Stream
1
2, 8
X
0
1
0
1
N/A
Invalid
Data In
High–Z
1
2, 8
X
1
0
0
0
N/A
Invalid
Stream
Data In
1
2, 8
X
1
0
1
0
N/A
Invalid
High–Z
Data In
1
2, 8
NOTES:
1. A ‘0’ represents an input voltage ≤ VIL and a ‘1’ represents an input voltage ≥ VIH. All inputs must satisfy the specified setup and hold times
for the falling or rising edge of K. Some entries in this truth table represent latched values. This table assumes that the chip is selected (i.e.,
E1 = 0 and E2 = 1) and VCC current is equal to ICCA. If this is not true, the chip will be in standby mode, the VCC current will equal ISB1 or ISB2
DPE will default to 1 and all RAM outputs will be in High–Z. Other possible combinations of control inputs not covered by this note or the table
above are not supported and the RAM’s behavior is not specified.
2. If either IE signal is sampled low on the rising edge of clock, the corresponding OE is a don’t care, and the corresponding outputs are High–Z.
3. A read cycle is defined as a cycle where data is driven on the internal data bus by the RAM.
4. DPE is registered on the rising edge of K at the beginning of the following clock cycle
5. No RAM cycle is performed.
6. A write cycle is defined as a cycle where data is driven onto the internal data bus through one of the data I/O ports (PDQ0 – PDQ7 and PDQP
or SDQ0 – SDQ7 and SPDQ), and written into the RAM.
7. Data is driven on the internal data bus by one I/O port through its data input register and latched into the data output latch of the other I/O
port.
8. Data contention will occur.
MCM62110
2
MOTOROLA FAST SRAM
PARITY CHECKER
Parity Scheme
DPE
E1 = VIH and/or E2 = VIL
RAMP = RAM0 ⊕ RAM1 ⊕ . . . ⊕ RAM7
1
1
0
RAMP ≠ RAM0 ⊕ RAM1 ⊕ . . . ⊕ RAM7
NOTE: RAMP, RAM0, RAM1 . . . , refer to the data that is present on the RAMs internal bus,
not necessarily data that resides in the RAM array. DPE is always delayed one
clock, and is registered on the rising edge of K at the beginning of the following clock
cycle (see AC CHARACTERISTICS).
ABSOLUTE MAXIMUM RATINGS (Voltages Referenced to VSS = VSSQ = 0 V)
Rating
Symbol
Value
Unit
VCC
– 0.5 to + 7.0
V
Vin, Vout
– 0.5 to VCC + 0.5
V
Output Current (per I/O)
Iout
± 20
mA
Power Dissipation
PD
1.2
W
Temperature Under Bias
Tbias
– 10 to + 85
°C
Operating Temperature
TA
0 to +70
°C
Power Supply
Voltage Relative to VSS/VSSQ for Any
Pin Except VCC and VCCQ
Tstg
– 55 to + 125
°C
NOTE: Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are
exceeded. Functional operation should be restricted to RECOMMENDED OPERATING CONDITIONS. Exposure to higher than recommended voltages for
extended periods of time could affect device reliability.
Storage Temperature
MOTOROLA FAST SRAM
This device contains circuitry to protect the
inputs against damage due to high static voltages or electric fields; however, it is advised
that normal precautions be taken to avoid
application of any voltage higher than maximum rated voltages to this high–impedance
circuit.
This CMOS memory circuit has been
designed to meet the dc and ac specifications
shown in the tables, after thermal equilibrium
has been established.
This device contains circuitry that will
ensure the output devices are in High–Z at
power up.
MCM62110
3
DC OPERATING CONDITIONS AND CHARACTERISTICS
(VCC = 5.0 V ± 10%, VCCQ = 5.0 V or 3.3 V ± 10%, TA = 0 to + 70°C, Unless Otherwise Noted)
RECOMMENDED OPERATING CONDITIONS (Voltages referenced to VSS = VSSQ = 0 V)
Parameter
Symbol
Min
Max
Unit
VCC
4.5
5.5
V
VCCQ
4.5
3.0
5.5
3.6
V
Input High Voltage
VIH
2.2
VCC + 0.3
V
Input Low Voltage
VIL
– 0.5*
0.8
V
Symbol
Min
Max
Unit
Input Leakage Current (All Inputs, Vin = 0 to VCC)
Ilkg(I)
—
± 1.0
µA
Output Leakage Current (POE, SOE = VIH)
Ilkg(O)
—
± 1.0
µA
—
—
—
190
190
190
Supply Voltage (Operating Voltage Range)
Output Buffer Supply Voltage (5.0 V TTL Compatible)
(3.3 V 50 Ω Compatible)
* VIL (min) = – 3.0 V ac (pulse width ≤ 20 ns)
DC CHARACTERISTICS
Parameter
AC Supply Current (All Inputs = VIL or VIH,VIL = 0.0 V and VIH ≥ 3.0 V,
Iout = 0 mA, Cycle Time ≥ tKHKH min)
MCM62110–15: tKHKH = 15 ns
MCM62110–17: tKHKH = 17 ns
MCM62110–20: tKHKH = 20 ns
ICCA
TTL Standby Current (VCC = Max, E1 = VIH or E2 = VIL)
ISB1
—
40
mA
CMOS Standby Current (VCC = Max, f = 0 MHz, E1 = VIH or E2 = VIL,
Vin ≤ VSS + 0.2 V or ≥ VCC – 0.2 V)
ISB2
—
30
mA
Output Low Voltage (IOL = + 8.0 mA, DPE: IOL = + 23.0 mA)
VOL
—
0.4
V
Output High Voltage (IOH = – 4.0 mA)
VOH
2.4
—
V
Symbol
Typ
Max
Unit
Cin
2
3
pF
Cout
6
7
pF
Cout(DPE)
6
7
pF
mA
CAPACITANCE (f = 1.0 MHz, dV = 3.0 V, TA = 25°C, Periodically Sampled Rather Than 100% Tested)
Parameter
Input Capacitance (All Pins Except I/Os)
Input/Output Capacitance (PDQ0 – PDQ7, SDQ0 – SDQ7, PDQP, SDQP)
Data Parity Error Output Capacitance (DPE)
AC SPEC LOADS
+5V
RL = 50 Ω
DQ
480 Ω
DQ
255 Ω
Z0 = 50 Ω
+5V
200 Ω
DPE
5 pF
50 pF
VL = 1.5 V
Figure 1A
MCM62110
4
Figure 1B
Figure 1C
MOTOROLA FAST SRAM
AC OPERATING CONDITIONS AND CHARACTERISTICS
(VCC = 5.0 V ± 10%, VCCQ = 5.0 V or 3.3 V ± 10%, TA = 0 to + 70°C, Unless Otherwise Noted)
Input Timing Measurement Reference Level . . . . . . . . . . . . . . . 1.5 V
Input Pulse Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 3.0 V
Input Rise/Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ns
Output Measurement Timing Level . . . . . . . . . . . . . . . . . . . . . . . 1.5 V
Output Load . . . . . . . . . . . . See Figure 1A Unless Otherwise Noted
READ CYCLE (See Note 1)
MCM62110–15
Parameter
MCM62110–17
MCM62110–20
Symbol
Min
Max
Min
Max
Min
Max
Unit
Notes
Read Cycle Time Clock High to Clock High
tKHKH
15
—
17
—
20
—
ns
1, 2
Clock Low Pulse Width
tKLKH
5
—
5
—
5
—
ns
Clock High Pulse Width
tKHKL
7
—
7
—
7
—
ns
Clock High to DPE Valid
tKHDPEV
—
7
—
8
—
10
ns
5
Clock High to Output Valid
tKHQV
—
7
—
7.5
—
10
ns
4, 3
Clock (K) High to Output Low Z After Write
tKHQX1
8
—
8
—
8
—
ns
Output Hold from Clock High
tKHQX2
5
—
5
—
5
—
ns
4, 6
tKHQZ
—
8
—
9
—
10
ns
6
A
W
E1, E2
PIE
SIE
POE
SOE
tAVKL
tWHKH
tEVKL
tPIEHKH
tSIEHKH
tPOEVKH
tSOEVKH
2.5
—
2.5
—
2.5
—
ns
A
W
E1, E2
PIE
SIE
POE
SOE
tKLAX
tKHWX
tKLEX
tKHPIEX
tKHSIEX
tKHPOEX
tKHSOEX
2
Output Enable High to Q High–Z
tPOEHQZ
tSOEHQZ
0
8
0
9
0
9
ns
6
Output Hold from Output Enable High
tPOEHQX
tSOEHQX
5
—
5
—
5
—
ns
6
Output Enable Low to Q Active
tPOELQX
tSOELQX
0
—
0
—
0
—
ns
6
Output Enable Low to Output Valid
tPOELQV
tSOELQV
—
5
—
6
—
8
ns
Clock High to Q High–Z (E1 or E2 = False)
Setup TImes:
Hold Times:
7
7
—
2
—
2
—
ns
7
7
NOTES:
1. A read is defined by W high for the setup and hold times.
2. All read cycle timing is referenced from K, SOE, or POE.
3. Access time is controlled by tKLQV if the clock low pulse width is less than (tKLQV–tKHQV); otherwise it is controlled by KHQV.
4. K must be at a high level for outputs to transition.
5. DPE is valid exactly one clock cycle after the output data is valid.
6. Transition is measured ± 500 mV from steady–state voltage with output load of Figure 1B. This parameter is sampled and not 100% tested.
At any given voltage and temperature, tKHQZ is less than tKHQX, tPOEHQZ is less than tPOELQX for a given device, and tSOEHQZ is less
than tSOELQX for a given device.
7. These read cycle timings are used to guarantee proper parity operation only.
MOTOROLA FAST SRAM
MCM62110
5
READ CYCLE (See Notes)
tKLKH
tKHKH
tKHKL
K
tKLAX
tAVKL
An
A0 – A14
An + 1
An + 2
E1
tKLEX
tEVKL
E2
tKHPIEX
tPIEHKH
PIE
tKHSIEX
tSIEHKH
SIE
tKHWX
tWHKH
W
tPOEVKH
tKHPOEX
POE
tPOELQV
tPOELQX
tPOEHQZ
tPOEHQX
SOE
tSOELQV
Qn
PDQ0 – PDQ7, PDQP
tKHQZ
tKHQV
Qn
SDQ0 – SDQ7, SDQP
tKHQX2
tKHDPEV
DPE
tKHQX1
DPE – 2
DPEn – 1
DPEn
NOTES:
1. DPE is valid exactly one clock cycle after the output data is valid.
MCM62110
6
MOTOROLA FAST SRAM
WRITE CYCLE (See Note 1)
MCM62110–15
Parameter
MCM62110–17
MCM62110–20
Symbol
Min
Max
Min
Max
Min
Max
Unit
Notes
Write Cycle Times
tKHKH
15
—
17
—
20
—
ns
1, 2
Clock Low Pulse Width
tKLKH
5
—
5
—
5
—
ns
Clock High Pulse Width
tKHKL
7
—
7
—
7
—
ns
Clock High to Output High–Z (W = VIL and
SIE = PIE = VIH)
tKHQZ
—
8
—
9
—
10
ns
Setup Times:
tAVKL
tWLKH
tEVKL
tPIEVKH
tSIEVKH
tDVKH
2.5
—
2.5
—
2.5
—
ns
Hold Times:
tKLAX
tKHWX
tKLEX
tKHPIEX
tKHSIEX
tKHDX
2
—
2
—
2
—
ns
tKHQV
—
7
—
7.5
—
8
ns
5
Output Enable High to Q High–Z
tPOEHQZ
tSOEHQZ
0
8
0
9
0
9
ns
6
Output Hold from Output Enable High
tPOEHQX
tSOEHQX
5
—
5
—
5
—
ns
Output Enable Low to Q Active
tPOELQX
tSOELQX
0
—
0
—
0
—
ns
Output Enable Low to Output Valid
tPOELQV
tSOELQV
—
5
—
6
—
8
ns
A
W
E1, E2
PIE
SIE
SDQ0 – SDQ7, SDQP, PDQ0 – PDQ7, PDQP
A
W
E1, E2
PIE
SIE
SDQ0 – SDQ7, SDQP, PDQ0 – PDQ7, PDQP
Write with Streaming (PIE = SOE = VIL or
SIE = POE = VIL)
Clock High to Output Valid
3, 4
6
NOTES:
1. A write is performed with W = VIL, E1 = VIL, E2 = VIH for the specified setup and hold times and either PIE = VIL or SIE = VIL. If both PIE =
VIL and SIE = VIL or PIE = VIH and SIE = VIH, then this is treated like a NOP and no write is performed.
2. All write cycle timings are referenced from K.
3. K must be at a high level for the outputs to transition.
4. Transition is measured ± 500 mV from steady–state voltage with output load of Figure 1B. This parameter is sampled and not 100% tested.
At any given voltage and temperature, tKHQZ is less than tKHQX for a given device.
5. A write with streaming is defined as a write cycle which writes data from one data bus to the array and outputs the same data onto the other
data bus.
6. Transition is measured ± 500 mV from steady–state voltage with output load of Figure 1B. This parameter is sampled and not 100% tested.
At any given voltage and temperature, tKHQZ is less than tKHQX, tPOEHQZ is less than tPOELQX for a given device, and tSOEHQZ is less
than tSOELQX for a given device.
MOTOROLA FAST SRAM
MCM62110
7
WRITE THROUGH — READ — WRITE (See Note)
tKHKH
tKLKH
tKHKL
K
tKLAX
tAVKL
An
A0 – A14
An + 1
An + 2
E1
tKLEX
tEVKL
E2
tKHPIEX
tPIEVKH
tPIEHKH
tKHPIEX
tSIEVKH
tSIEHKH
tKHSIEX
tWLKH
tWHKH
tKHWX
PIE
tKHSIEX
SIE
tKHWX
W
POE
tPOEHQZ
SOE
tPOEHQX
tSOEHQZ
tPOELQV
tSOEHQX
tDVKH
tKHDX
tSOELQV
PDQ0 – PDQ7, PDQP
Dn
Qn – 1
Qn – 1
tPOEHQZ
tDVKH
Qn
+1
Dn + 2
tPOELQX
tKHQV
SDQ0 – SDQ7, SDQP
tKHDX
Qn
(STREAMED)
tKHDPEV
DPE
DPEn – 2
DPEn – 1
NOTE: DPE is valid exactly one clock cycle after the output data is written.
MCM62110
8
MOTOROLA FAST SRAM
STREAM CYCLE (See Note 1)
MCM62110–15
Parameter
MCM62110–17
MCM62110–20
Symbol
Min
Max
Min
Max
Min
Max
Unit
Notes
Stream Cycle Time
tKHKH
15
—
17
—
20
—
ns
1, 2
Clock Low Pulse Width
tKLKH
5
—
5
—
5
—
ns
Clock High Pulse Width
tKHKL
7
—
7
—
7
—
ns
Stream Access Time
tKHQV
—
7
—
7.5
—
8
ns
Setup Times:
tAVKL
tWHKH
tEVKL
tPIEVKH
tSIEVKH
tDVKH
2.5
—
2.5
—
2.5
—
ns
Hold Times:
tKLAX
tKHWX
tKLEX
tKHPIEX
tKHSIEX
tKHDX
2
—
2
—
2
—
ns
Output Enable High to Q High–Z
tPOEHQZ
tSOEHQZ
0
8
0
9
0
9
ns
3
Output Enable Low to Q Active
tPOELQX
tSOELQX
0
—
0
—
0
—
ns
3
Output Enable Low to Output Valid
tPOELQV
tSOELQV
—
5
—
6
—
8
ns
A
W
E1, E2
PIE
SIE
SDQ0 – SDQ7, SDQP, PDQ0 – PDQ7, PDQP
A
W
E1, E2
PIE
SIE
SDQ0 – SDQ7, SDQP, PDQ0 – PDQ7, PDQP
NOTES:
1. A stream cycle is defined as a cycle where data is passed from one data bus to the other data bus.
2. All stream cycle timing is referenced from K.
3. Transition is measured ± 500 mV from steady–state voltage with output load of Figure 1B. This parameter is sampled and not 100% tested.
At any given voltage and temperature, tPOEHQZ is less than tPOELQX, tSOEHQZ is less than tSOELQX, and tKHQZ is less than tKHQX
for a given device.
MOTOROLA FAST SRAM
MCM62110
9
STREAM CYCLE (See Note)
tKHKH
tKLKH
tKHKL
K
tKLAX
tAVKL
An
A0 – A14
An + 1
An + 2
E1
tKLEX
tEVKL
E2
tKHPIEX
tPIEVKH
PIE
tKHSIEX
tSIEVKH
SIE
tKHWX
tWHKH
W
POE
tPOEHQZ
SOE
tSOEHQZ
tDVKH
PDQ0 – PDQ7, PDQP
tKHQV
tKHDX
Qn – 1
Dn
Qn + 1 (STREAMED)
tKHQV
SDQ0 – SDQ7, SDQP
Qn
(STREAMED)
Qn – 1
Dn + 1
tKHDPEV
DPEn – 2
DPE
DPEn – 1
NOTE: DPE is valid exactly one clock cycle after the output data is valid.
ORDERING INFORMATION
(Order by Full Part Number)
MCM
62110
FN
XX
Motorola Memory Prefix
Speed (15 = 15 ns, 17 = 17 ns, 20 = 20 ns)
Part Number
Package (FN = PLCC)
Full Part Numbers — MCM62110FN15
MCM62110
10
MCM62110FN17
MCM62110FN20
MOTOROLA FAST SRAM
PACKAGE DIMENSIONS
FN PACKAGE
52–LEAD PLCC
CASE 778–02
B
Y BRK
-N-
0.007 (0.180)
M
T L –M
0.007 (0.180)
U
M
S
N
T L –M
S
N
S
0.010 (0.250)
S
S
D
-L-
-M-
52
LEADS
ACTUAL
(NOTE 1)
52
Z
W
D
1
G1
X
VIEW D-D
V
A
0.007 (0.180)
M
T L –M
S
N
S
R
0.007 (0.180)
M
T L –M
S
N
S
T L –M
N
S
S
Z
C
H
0.004 (0.100)
G
J
-T-
F
S
N
S
0.007 (0.180)
M
T L –M
S
N
S
VIEW S
G1
0.010 (0.250)
T L –M
K
SEATING
PLANE
VIEW S
S
M
K1
E
(NOTE 1)
52
0.007 (0.180)
T L –M
S
N
S
NOTES:
1. DUE TO SPACE LIMITATION, CASE 778-02 SHALL BE
REPRESENTED BY A GENERAL (SMALLER) CASE
OUTLINE DRAWING RATHER THAN SHOWING ALL 52
LEADS.
2. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF
LEAD SHOULDER EXITS PLASTIC BODY AT MOLD
PARTING LINE.
3. DIM G1, TRUE POSITION TO BE MEASURED AT DATUM -T-,
SEATING PLANE.
4. DIM R AND U DO NOT INCLUDE MOLD FLASH.
ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE.
5. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M,
1982.
6. CONTROLLING DIMENSION: INCH.
7. THE PACKAGE TOP MAY BE SMALLER THAN THE
PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS
R AND U ARE DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD
FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD
FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE
TOP AND BOTTOM OF THE PLASTIC BODY.
8. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION
TO BE GREATER THAN 0.037 (0.940). THE DAMBAR
INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO
BE SMALLER THAN 0.025 (0.635).
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
INCHES
MIN
MAX
0.785 0.795
0.785 0.795
0.165 0.180
0.090 0.110
0.013 0.019
0.050 BSC
0.026 0.032
—
0.020
—
0.025
0.750 0.756
0.750 0.756
0.042 0.048
0.042 0.048
0.042 0.056
0.020
—
10°
2°
0.710 0.730
0.040
—
MILLIMETERS
MIN
MAX
19.94 20.19
19.94 20.19
4.20
4.57
2.29
2.79
0.33
0.48
1.27 BSC
0.66
0.81
0.51
—
0.64
—
19.05 19.20
19.05 19.20
1.07
1.21
1.07
1.21
1.07
1.42
—
0.50
2°
10°
18.04 18.54
1.02
—
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
MOTOROLA FAST SRAM
MCM62110
11
Literature Distribution Centers:
USA/EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036.
JAPAN: Nippon Motorola Ltd.; 4–32–1, Nishi–Gotanda, Shinagawa–ku, Tokyo 141, Japan.
ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, No. 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong.
MCM62110
12
◊
CODELINE TO BE PLACED HERE
*MCM62110/D*
MCM62110/D
MOTOROLA FAST
SRAM