ITT MH00S1NCGD Half-inch rotary switch Datasheet

C&K M Series
Half-inch Rotary Switches
Features/Benefits
• Multi-pole and multi-positions
• Panel and PCB mounting
• Stainless steel actuator
• Non-shorting contacts
Typical Applications
• Test equipment
• Industrial equipment
• Medical equipment
Models Available
Specifications
Materials
CONTACT RATING: Q contact material: Carry-6 AMPS continuous.
Switch-250 mA max. @ 125 V AC or 28 DC. Non-shorting
contacts standard. See page L-15 for additional ratings.
ELECTRICAL LIFE: 10,000 make-and-break cycles at 150 mA,
125 V AC or 28 DC.
CONTACT RESISTANCE: Below 20 mΩ typ. initial @
2-4 V DC, 100 mA, for both silver and gold plated contacts.
INSULATION RESISTANCE: 1010 Ω min.
DIELECTRIC STRENGTH: 600 Vrms min. @ sea level.
OPERATING & STORAGE TEMPERATURE: –30ºC to 85ºC.
OPERATING TORQUE: 4-7 ounces-inches typ. initial.
SOLDERABILITY: Per MIL-STD-202F method 208D, or
EIA RS-186E method 9 (1 hour steam aging).
HOUSING AND BUSHING: Zinc alloy, bright zinc plated,
with clear chromate finish.
ACTUATOR: Zinc alloy, nickel plated or stainless steel.
BASE: Diallylphthalate (DAP) or melamine phenolic, with insert
molded terminals.
ROTOR: Glass filled polyester (UL 94V-0).
MOVABLE CONTACTS:
Non-shorting: Q contact material: Copper alloy, silver plated.
See page L-15 for additional contact materials.
STATIONARY CONTACT & ALL TERMINALS: Q contact material:
Copper alloy, silver plated. All terminals insert molded. All
terminals present regardless of number of switch positions.
See page L-15 for additional contact materials.
CONTACT SPRING: Music wire, phosphate coated.
STOP PIN: Stainless steel.
STOP RING: Brass.
HARDWARE: Nut: Brass, nickel plated; Lockwasher: Steel,
nickel plated.
NOTE: Any models supplied with Q or G contact material are RoHS compliant. For the
latest information regarding RoHS compliance, please go to: www.ittcannon.com/rohs.
NOTE: Specifications and materials listed above are for switches with standard options.
For information on specific and custom switches, consult Customer Service Center.
Rotary
L
Build-A-Switch
To order, simply select desired option from each category and place in the appropriate box. Available options are shown and
described on pages L-13 thru L-17. For additional options not shown in catalog, consult Customer Service Center.
Switch Function
MA00 SP, 10 pos., 36°
MA02 SP, 2 pos., 36°
MA03 SP, 3 pos., 36°
MA04 SP, 4 pos., 36°
MA05 SP, 5 pos., 36°
MA06 SP, 6 pos., 36°
MA10 SP, 10 pos., 36°
MB00 DP, 5 pos., 36°
MB03 DP, 3 pos., 36°
MB04 DP, 4 pos., 36°
MB05 DP, 5 pos., 36°
MC00 SP, 12 pos., 30°
MC03 SP, 3 pos., 30°
MC07 SP, 7 pos., 30°
MC12 SP, 12 pos., 30°
MD00 DP, 6 pos., 30°
MD06 DP, 6 pos., 30°
ME00 SP, 10 pos., 36°
ME04 SP, 4 pos., 36°
MF00 DP, 5 pos., 36°
MG00 SP, 12 pos., 30°
MH00 DP, 6 pos., 30°
Actuator & Bushing
L1 .650" long, flatted
L2 Screwdriver slot, flush
L3 .650" long, round
S1 .650" long, flatted
S2 Screwdriver slot, flush
S3 .650" long, round
S6 .785" long, slot
Short/Non-short
N Non-shorting contacts
Terminations
Z Solder lug
C PC Thru-hole
Contact Material
Q Silver
G Gold over silver
Seal
D No seal
F Splashproof shaft & panel seal
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
L–12
www.ittcannon.com
C&K M Series
Half-inch Rotary Switches
SWITCH FUNCTION
SP MODELS 36º INDEXING
SCHEMATIC
36º INDEXING
NO.
POLES
SP
MODEL NO.
WITH STOP
PINS
MODEL NO.
WITH STOP
RINGS
MA00
ME00
10 Positions
No Stops
MA02
—
2 Positions
MA03
—
3 Positions
MA04
ME04
4 Positions
MA05
—
5 Positions
MA06
—
6 Positions
MA10
—
10 Positions
MF00
5 Positions
No Stops
MB00
MB03
DP
SWITCH
FUNCTION
30º INDEXING
NO.
POLES
DP MODELS 36º INDEXING
SCHEMATIC
MODEL NO.
WITH STOP
PINS
MODEL NO.
WITH STOP
RINGS
MC00
MG00
12 Positions
No Stops
MC03
—
3 Positions
MC07
—
7 Positions
MC12
—
12 Positions
MD00
MH00
6 Positions
No Stops
MD06
—
6 Positions
SP
SWITCH
FUNCTION
DP
SP MODELS 30º INDEXING
SCHEMATIC
3 Positions
MB04
—
4 Positions
MB05
—
5 Positions
DP MODELS 30º INDEXING
SCHEMATIC
All models
with all options when ordered with S1-SB stainless steel actuator options.
NOTE: Number of positions or stops preset at factory (NOTE: MX00 models have full 360 rotation with no stops. Stop pins or stop rings supplied for user-selectable stops, see above).
All terminals present regardless of number of switch positions. Hardware is available separately, see section “Technical Data and Additional Hardware”.
L
Rotary
SP, 36º Indexing
DP, 36º Indexing
Terminal Numbers Marked
On Side Of Housing
Actuator Shown In Pos. 1
Part number shown: MA00L1NZQD
SP, 30º Indexing
DP, 30º Indexing
Terminal Numbers Marked
On Side Of Housing
Actuator Shown In Pos. 1
Part number shown: MC00L1NZQD
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
L–13
www.ittcannon.com
C&K M Series
Half-inch Rotary Switches
ACTUATOR (ZINC ALLOY)
L1
.650" LONG, FLATTED
L3
.650" LONG, ROUND
L2
SCREWDRIVER SLOT, FLUSH
All actuators shown in pos. 1
ACTUATOR (STAINLESS STEEL)
Rotary
L
S1
.650" LONG, FLATTED
S2
SCREWDRIVER SLOT, FLUSH
S3
.650" LONG, ROUND
S6
.785" LONG, SLOT
All actuators shown in pos. 1
All models UL/CSA when ordered with stainless steel actuators.
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
L–14
www.ittcannon.com
C&K M Series
Half-inch Rotary Switches
SHORTING/NON-SHORTING CONTACTS
N
NON-SHORTING CONTACTS
Break-before-make
TERMINATIONS
Z
C
SOLDER LUG
SP
DP
PC THRU-HOLE
SP
DP
PANEL MOUNTING
PC MOUNTING
36 º INDEXING
WITHOUT FLATS
WITH FLATS
0.213
(5.41)
SP
DP
0.260 DIA
(6.59)
0.260 DIA
(6.60)
L
PC MOUNTING
30 º INDEXING
DP
NOTE: Q contact material standard. Terminal numbers marked on side of housing.
All terminals insert molded. All terminals present regardless of number of switch positions.
Actuators and schematics shown in pos. 1.
CONTACT MATERIAL
CONTACT
MATERIAL
OPTION
CODE
RoHS
COMPLIANT*
RoHS
COMPATIBLE*
Q
YES
YES
SILVER 1, 2
SILVER 2
POWER
CARRY: 6 AMPS CONTINUOUS. SWITCH: 250 mA @ 125 V AC
or 28 V DC.
G
YES
YES
GOLD OVER
SILVER 3, 4
GOLD 4
LOW LEVEL/DRY CIRCUIT
OR POWER
0.4 VA MAX. @ 20 V AC or DC MAX. or, CARRY: 6 AMPS
CONTINUOUS. SWITCH: 250 mA @ 125 V AC or 28 V DC.
TERMINAL
PLATING
RATING
* Note: See Technical Data section of this catalog for RoHS compliant and compatible definition and specifications.
1
MOVABLE CONTACTS: Non-shorting: Copper alloy, silver plated.
Shorting: Zinc alloy, silver plated.
2
STATIONARY CONTACTS & ALL TERMINALS: Copper alloy, silver plated.
NOTE: Any models supplied with Q G contact material are RoHS
compliant. For the latest information regarding RoHS compliance,
please go to: www.ittcannon.com/rohs.
3
MOVABLE CONTACTS: Non-shorting: Copper alloy, with gold plate over nickel plate, over silver plate.
Shorting: Zinc alloy, with gold plate
All models
4
STATIONARY CONTACTS & ALL TERMINALS: Copper alloy, with gold plate
over nickel plate over silver plate.
when ordered with S1-S6 stainless steel actuator options.
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
L–15
www.ittcannon.com
Rotary
SP
Hardware: All models, one mounting nut and lockwasher
supplied standard. MA00 thru MD00 models: two stop pins
and adhesive mylar washer supplied. ME00 thru MH00
models: two stop rings supplied. Hardware is available
separately, see section “Technical Data and Additional
Hardware”.
C&K M Series
Half-inch Rotary Switches
SEAL
D
F
NO EPOXY SEAL
SPLASHPROOF SHAFT AND PANEL SEAL
Setting Stops With Stop Pins
MA00, MB00, MC00 & MD00 Models Only:
The number of switch positions or stops are adjustable by means of stop pins provided with each switch. Switches are normally
shipped with stop pins and hardware in bulk, not installed. Without stop pins, switches have full 360º rotation and no stops.
Note that all two pole models begin to repeat when actuated 180º or more.
To set stops, refer to figures 1 & 2. Orient switch so that terminal no. 1 is as shown. Turn actuator to position 1, using flats on
bushing and terminal no. 1 as reference. Install CCW stop pin in hole designated ‘X’. Install second stop pin in hole number
corresponding to the number of positions desired. Note that two pole models will begin to repeat when actuated 180º or more.
To retain stop pins, use adhesive mylar washer included; see figure 3.
All models except MX00 models have number of switch positions or stops pre-set at factory and are not adjustable.
Hardware:
Two stop pins, mounting nut, and lockwasher supplied standard.
P/N 537100000
Rotary
L
36º Indexing Models
Top View
30º Indexing Models
Top View
Fig. 1
Fig. 2
P/N 537202000
Fig. 3
Setting Stops With Stop Rings
ME00, MF00, MG00 & MH00 Models Only:
The number of switch positions or stops are adjustable by means of stop rings provided with each switch. These models are
normally shipped with stop rings and hardware in bulk, not installed. Without stop rings, switches have full 360º rotation and no
stops. Note that all two pole models begin to repeat when actuated 180º or more.
To set stops refer to figures 4 & 5. Orient switch so that terminal no. 1 is as shown. Turn actuator to pos. 1 using flats on bushing
and terminal no. 1 as reference. See figure 6 and install inner stop ring with short tab in hole designated ‘X’. Install outer
stop ring with long tab in hole number corresponding to the number of positions desired. Note that all two pole models begin to
repeat when actuated 180º or more. Use mounting nut and lockwasher to retain stop rings.
All MEXX, MFXX, MGXX & MHXX Models (Except MX00 models):
Number of switch positions or stops are preset at factory, but are user adjustable.
Hardware:
Two stop rings, mounting nut and lockwasher supplied standard.
36º Indexing Models
Top View
30º Indexing Models
Top View
Fig. 4
Fig. 5
Fig. 6
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
L–16
www.ittcannon.com
C&K M Series
Half-inch Rotary Switches
AVAILABLE HARDWARE
Washer
Stop pins
PART NO.
PART NO.
PART NO.
638100000 INNER-W/SHORT TAB
638101000 OUTER-W/LONG TAB
586800000 RUBBER PANEL SEAL
537202000 ADHESIVE MYLAR
537100000
Stop Ring
One each required for setting stops.
RETAINS STOP PINS
NOTE: Additional nuts and lockwashers available separately, see section “Technical Data and Additional Hardware”.
L
Rotary
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
L–17
www.ittcannon.com
Similar pages