TDK MHQ1005P11NST Inductors for high frequency circuit Datasheet

I
N
D
U
C
T
O
R
S
September 2013
Inductors for High Frequency Circuits
Multilayer Ceramic
MHQ-Pseries
MHQ0603P
MHQ1005P
0603 [0201 inch]*
1005 [0402 inch]
* Dimensions Code JIS[EIA]
(2/17)
I
N
D
U
C
T
O
R
S
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
001-01 / 20130929 / inductor_high-frequency_mhq_en.fm
(3/17)
I
N
D
U
C
T
O
R
S
Inductors for High Frequency Circuits
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
AEC-Q200
Multilayer Ceramic
Overview of the MHQ-P Series
FEATURES
Unique ceramic material and configuration allows for the realization of high Q characteristics that are equivalent to that of air core wound
inductors.
Multilayer method allows for a lineup with fine increments of inductance.
APPLICATION
Smart phones, tablet terminals, high frequency modules (PAs, VCOs, FEMs , etc.), Bluetooth, W-LAN, UWB, tuners, automotive equipment
and other high frequency circuits for the mobile communication industry
PART NUMBER CONSTRUCTION
MHQ
Series name
0603
L×W×H Dimensions
(mm)
0603 0.65×0.35×0.35
1005
1.0×0.5×0.5
P
Characteristics
P
0N6
S
Inductance
(nH)
0N6
0.6
1N1
1.1
11N
11
Inductance
tolerance
B
±0.1nH
C
±0.2nH
S
±0.3nH
G
±2%
H
±3%
J
±5%
T
□□□
Packaging style
Internal code
T
Taping
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Package quantity
Operating
Storage
temperature
temperature
(pieces/reel)
（°C）
（°C）
MHQ0603P
–55 to +125
–55 to +125
15000
MHQ1005P
–55 to +125
–55 to +125
10000
The Storage temperature range is for after the circuit board is mounted.
Type
Individual weight
（mg）
1
1
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
• All specifications are subject to change without notice.
001-01 / 20130929 / inductor_high-frequency_mhq_en.fm
(4/17)
I
N
D
U
C
T
O
R
S
Overview of the MHQ-P Series
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T: Temperature
T4
T3
T2
T3
t3
T1
t1
t2
t: Time
Preheating
Temp.
T1
T2
150°C
180°C
Time
t1
60 to 120s
Soldering
Temp.
Time
T3
t2
230°C
30 to 60s
Peak
Temp.
T4
250 to 260°C
Time
t3
10s max.
• All specifications are subject to change without notice.
001-01 / 20130929 / inductor_high-frequency_mhq_en.fm
(5/17)
I
N
D
U
C
T
O
R
S
MHQ-Pseries
MHQ0603P Type
0.35±0.05
SHAPE & DIMENSIONS
0.09±0.04
0.09±0.04
0.35±0.05
0.65±0.05
0.15±0.05
Dimensions in mm
0.15±0.05
0.30
RECOMMENDED LAND PATTERN
0.25
0.30
0.25
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20130929 / inductor_high-frequency_mhq_en.fm
(6/17)
I
N
D
U
C
T
O
R
S
MHQ-Pseries MHQ0603P Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
L
(nH)
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.7
5.1
5.6
6.2
Tolerance
±0.1, ±0.2nH
±0.1, ±0.2nH
±0.1, ±0.2nH
±0.1, ±0.2nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.1, ±0.2, ±0.3nH
±0.2, ±0.3nH, ±3%
±0.2, ±0.3nH, ±3%
±0.2, ±0.3nH, ±3%
±0.2, ±0.3nH, ±3%
±0.3nH, ±3%
Self-resonant
L measuring
Q measuring
frequency
Q
frequency
frequency
(GHz)
min.
(MHz)
(MHz)
min.
typ.
500
500
10.0
20.0
−
500
500
10.0
20.0
−
500
500
10.0
20.0
−
500
500
10.0
18.8
−
500
500
10.0
19.3
−
500
500
10.0
19.3
−
500
500
10.0
20.0
−
500
500
10.0
20.0
−
500
500
10.0
18.6
−
500
16
500
10.0
19.5
500
16
500
10.0
17.5
500
16
500
10.0
16.7
500
16
500
10.0
15.8
500
16
500
10.0
16.1
500
16
500
10.0
13.8
500
16
500
10.0
12.7
500
16
500
10.0
13.2
500
16
500
10.0
12.5
500
16
500
8.0
11.7
500
16
500
8.0
11.1
500
16
500
8.0
11.1
500
16
500
8.0
10.5
500
16
500
8.0
10.6
500
16
500
8.0
10.8
500
16
500
8.0
10.3
500
16
500
8.0
10.5
500
16
500
7.0
9.5
500
16
500
7.0
9.6
500
16
500
6.5
9.3
500
16
500
6.5
9.5
500
16
500
6.5
9.1
500
16
500
6.5
9.1
500
16
500
6.5
9.1
500
16
500
6.5
9.2
500
16
500
6.0
8.5
500
16
500
6.0
8.3
500
16
500
6.0
8.2
500
16
500
6.0
8.2
500
16
500
5.5
7.9
500
16
500
5.5
7.8
500
16
500
5.0
7.1
500
16
500
4.0
6.7
DC resistance
(: )
max.
0.07
0.07
0.07
0.07
0.07
0.07
0.08
0.10
0.10
0.10
0.10
0.10
0.12
0.12
0.12
0.15
0.15
0.15
0.15
0.25
0.25
0.25
0.25
0.30
0.30
0.30
0.20
0.25
0.25
0.25
0.25
0.25
0.30
0.35
0.35
0.35
0.35
0.35
0.40
0.40
0.40
0.70
typ.
0.02
0.02
0.02
0.02
0.03
0.03
0.04
0.06
0.06
0.05
0.06
0.07
0.07
0.08
0.08
0.08
0.09
0.08
0.08
0.17
0.16
0.16
0.18
0.19
0.19
0.19
0.13
0.15
0.14
0.17
0.16
0.17
0.19
0.23
0.26
0.22
0.23
0.23
0.25
0.24
0.29
0.52
Rated current
Part No.*
(mA)
max.
1000
1000
1000
1000
1000
1000
1000
800
800
800
800
800
700
700
700
700
700
700
700
500
500
500
500
450
450
450
550
500
500
500
500
450
450
400
400
400
400
400
350
350
350
300
MHQ0603P0N6△T□□□
MHQ0603P0N7△T□□□
MHQ0603P0N8△T□□□
MHQ0603P0N9△T□□□
MHQ0603P1N0△T□□□
MHQ0603P1N1△T□□□
MHQ0603P1N2△T□□□
MHQ0603P1N3△T□□□
MHQ0603P1N4△T□□□
MHQ0603P1N5△T□□□
MHQ0603P1N6△T□□□
MHQ0603P1N7△T□□□
MHQ0603P1N8△T□□□
MHQ0603P1N9△T□□□
MHQ0603P2N0△T□□□
MHQ0603P2N1△T□□□
MHQ0603P2N2△T□□□
MHQ0603P2N3△T□□□
MHQ0603P2N4△T□□□
MHQ0603P2N5△T□□□
MHQ0603P2N6△T□□□
MHQ0603P2N7△T□□□
MHQ0603P2N8△T□□□
MHQ0603P2N9△T□□□
MHQ0603P3N0△T□□□
MHQ0603P3N1△T□□□
MHQ0603P3N2△T□□□
MHQ0603P3N3△T□□□
MHQ0603P3N4△T□□□
MHQ0603P3N5△T□□□
MHQ0603P3N6△T□□□
MHQ0603P3N7△T□□□
MHQ0603P3N8△T□□□
MHQ0603P3N9△T□□□
MHQ0603P4N0△T□□□
MHQ0603P4N1△T□□□
MHQ0603P4N2△T□□□
MHQ0603P4N3△T□□□
MHQ0603P4N7△T□□□
MHQ0603P5N1△T□□□
MHQ0603P5N6△T□□□
MHQ0603P6N2△T□□□
The " △ " of the Part Number contains the inductance tolerance code, B（±0.1nH）, C（±0.2nH）, S（±0.3nH）, G（±2%）, H（±3%）or J（±5%）.
The " □□□ " of the Part Number contains the internal code.
・ Short bar residual inductance =0.556nH
○ Measurement equipment
Measurement item
Product No.
L, Q
4991A+16197A
Self-resonant frequency
8720C
DC resistance
Type-7561
＊ Equivalent measurement equipment may be used.
Manufacturer
Agilent Technologies
Agilent Technologies
Yokogawa
• All specifications are subject to change without notice.
001-01 / 20130929 / inductor_high-frequency_mhq_en.fm
(7/17)
I
N
D
U
C
T
O
R
S
MHQ-Pseries MHQ0603P Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
L
(nH)
6.8
7.5
8.2
9.1
10
11
12
13
15
16
18
20
22
24
27
30
33
36
39
Tolerance
±3%, ±5%
±3%, ±5%
±3%, ±5%
±3%, ±5%
±3%, ±5%
±3%, ±5%
±3%, ±5%
±3%, ±5%
±3%, ±5%
±3%, ±5%
±3%, ±5%
±3%, ±5%
±3%, ±5%
±3%, ±5%
±3%, ±5%
±3%, ±5%
±3%, ±5%
±3%, ±5%
±3%, ±5%
Self-resonant
L measuring
Q measuring
frequency
Q
frequency
frequency
(GHz)
min.
(MHz)
(MHz)
min.
typ.
500
16
500
4.0
6.8
500
16
500
3.8
5.7
500
16
500
3.8
5.4
500
16
500
3.8
5.5
500
16
500
3.5
5.2
500
16
500
3.2
4.6
500
16
500
3.2
4.6
500
16
500
3.2
4.5
500
16
500
2.8
4.2
500
16
500
2.5
4.0
500
16
500
2.4
3.7
500
16
500
2.4
3.5
500
16
500
2.2
3.3
500
16
500
2.1
3.1
500
16
500
2.0
2.9
500
16
500
1.9
2.7
300
14
300
1.8
2.5
300
14
300
1.7
2.4
300
14
300
1.6
2.3
DC resistance
(: )
max.
0.70
0.50
0.90
0.90
1.20
1.30
1.40
1.50
1.50
1.70
1.70
2.00
2.00
2.20
2.20
2.70
2.80
2.80
3.00
typ.
0.53
0.37
0.64
0.62
0.86
0.89
0.77
1.01
1.05
1.21
1.21
1.38
1.40
1.55
1.55
1.98
2.06
2.08
2.24
Rated current
Part No.*
(mA)
max.
300
300
250
250
240
240
240
180
180
180
180
160
160
160
160
160
160
160
160
MHQ0603P6N8△T□□□
MHQ0603P7N5△T□□□
MHQ0603P8N2△T□□□
MHQ0603P9N1△T□□□
MHQ0603P10N△T□□□
MHQ0603P11N△T□□□
MHQ0603P12N△T□□□
MHQ0603P13N△T□□□
MHQ0603P15N△T□□□
MHQ0603P16N△T□□□
MHQ0603P18N△T□□□
MHQ0603P20N△T□□□
MHQ0603P22N△T□□□
MHQ0603P24N△T□□□
MHQ0603P27N△T□□□
MHQ0603P30N△T□□□
MHQ0603P33N△T□□□
MHQ0603P36N△T□□□
MHQ0603P39N△T□□□
The " △ " of the Part Number contains the inductance tolerance code, B（±0.1nH）, C（±0.2nH）, S（±0.3nH）, G（±2%）, H（±3%）or J（±5%）.
The " □□□ " of the Part Number contains the internal code.
・ Short bar residual inductance =0.556nH
○ Measurement equipment
Measurement item
Product No.
L, Q
4991A+16197A
Self-resonant frequency
8720C
DC resistance
Type-7561
＊ Equivalent measurement equipment may be used.
Manufacturer
Agilent Technologies
Agilent Technologies
Yokogawa
• All specifications are subject to change without notice.
001-01 / 20130929 / inductor_high-frequency_mhq_en.fm
(8/17)
I
N
D
U
C
T
O
R
S
MHQ-Pseries MHQ0603P Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
L(nH)typ.
500MHz
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.7
5.1
5.6
6.2
800MHz
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.7
5.1
5.6
6.2
1.8GHz
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.4
4.9
5.3
5.9
6.6
2.0GHz
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.6
2.7
2.8
2.9
3.0
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.1
4.2
4.3
4.4
4.5
4.9
5.4
6.0
6.7
2.4GHz
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
3.1
3.2
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.2
4.3
4.4
4.5
4.6
5.1
5.5
6.2
7.0
Q typ.
500MHz
29min.
29min.
29min.
29min.
29min.
29min.
29min.
29min.
29min.
29
28
30
29
28
27
29
28
31
31
25
26
26
26
24
23
24
27
25
27
25
26
26
24
23
26
23
24
25
24
25
24
21
800MHz
38min.
38min.
38min.
38min.
38min.
38min.
38min.
38min.
38min.
38
37
39
38
38
35
37
37
40
41
32
34
34
35
31
30
32
35
32
35
33
33
34
32
30
34
30
31
33
31
32
31
28
1.8GHz
58min.
58min.
58min.
58min.
58min.
58min.
58min.
58min.
58min.
58
56
62
59
57
55
58
57
61
62
51
54
54
54
48
46
49
53
48
53
50
50
51
49
47
52
46
46
49
47
49
46
42
2.0GHz
60min.
60min.
60min.
60min.
60min.
60min.
60min.
60min.
60min.
60
60
65
62
60
58
62
61
64
64
53
56
57
55
51
48
51
55
50
55
52
52
52
51
49
53
48
48
51
49
51
48
43
2.4GHz
66min.
66min.
66min.
66min.
66min.
66min.
66min.
66min.
66min.
66
66
71
69
66
64
68
68
71
71
59
62
63
62
56
52
57
61
54
61
57
57
58
56
54
59
52
52
56
54
56
52
47
Part No.*
MHQ0603P0N6△T□□□
MHQ0603P0N7△T□□□
MHQ0603P0N8△T□□□
MHQ0603P0N9△T□□□
MHQ0603P1N0△T□□□
MHQ0603P1N1△T□□□
MHQ0603P1N2△T□□□
MHQ0603P1N3△T□□□
MHQ0603P1N4△T□□□
MHQ0603P1N5△T□□□
MHQ0603P1N6△T□□□
MHQ0603P1N7△T□□□
MHQ0603P1N8△T□□□
MHQ0603P1N9△T□□□
MHQ0603P2N0△T□□□
MHQ0603P2N1△T□□□
MHQ0603P2N2△T□□□
MHQ0603P2N3△T□□□
MHQ0603P2N4△T□□□
MHQ0603P2N5△T□□□
MHQ0603P2N6△T□□□
MHQ0603P2N7△T□□□
MHQ0603P2N8△T□□□
MHQ0603P2N9△T□□□
MHQ0603P3N0△T□□□
MHQ0603P3N1△T□□□
MHQ0603P3N2△T□□□
MHQ0603P3N3△T□□□
MHQ0603P3N4△T□□□
MHQ0603P3N5△T□□□
MHQ0603P3N6△T□□□
MHQ0603P3N7△T□□□
MHQ0603P3N8△T□□□
MHQ0603P3N9△T□□□
MHQ0603P4N0△T□□□
MHQ0603P4N1△T□□□
MHQ0603P4N2△T□□□
MHQ0603P4N3△T□□□
MHQ0603P4N7△T□□□
MHQ0603P5N1△T□□□
MHQ0603P5N6△T□□□
MHQ0603P6N2△T□□□
The " △ " of the Part Number contains the inductance tolerance code, B（±0.1nH）, C（±0.2nH）, S（±0.3nH）, G（±2%）, H（±3%）or J（±5%）.
The " □□□ " of the Part Number contains the internal code.
○ Measurement equipment
Product No.
Manufacturer
4291B+16193A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130929 / inductor_high-frequency_mhq_en.fm
(9/17)
I
N
D
U
C
T
O
R
S
MHQ-Pseries MHQ0603P Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
L(nH)typ.
500MHz
6.8
7.5
8.2
9.1
10
11
12
13
15
16
18
20
22
24
27
30
33
36
39
800MHz
6.8
7.5
8.2
9.2
10
11
12
13
15
16
18
21
23
25
28
32
35
38
42
1.8GHz
7.2
8.1
8.9
9.9
11
12
14
15
18
19
22
26
29
34
38
47
55
67
79
2.0GHz
7.4
8.3
9.2
10.2
11
13
14
16
19
20
24
28
32
38
44
2.4GHz
7.7
8.8
9.7
10.9
12
14
16
18
21
23
28
34
40
Q typ.
500MHz
22
24
21
23
22
21
23
21
23
22
23
22
23
22
23
22
22
22
23
800MHz
28
30
27
29
28
27
29
27
29
28
28
27
29
26
28
27
27
26
26
1.8GHz
43
44
39
42
41
37
41
36
37
37
36
33
34
29
30
2.0GHz
44
45
40
44
42
38
41
36
37
37
35
32
33
27
28
2.4GHz
48
48
42
46
43
39
41
36
36
35
33
27
28
Part No.*
MHQ0603P6N8△T□□□
MHQ0603P7N5△T□□□
MHQ0603P8N2△T□□□
MHQ0603P9N1△T□□□
MHQ0603P10N△T□□□
MHQ0603P11N△T□□□
MHQ0603P12N△T□□□
MHQ0603P13N△T□□□
MHQ0603P15N△T□□□
MHQ0603P16N△T□□□
MHQ0603P18N△T□□□
MHQ0603P20N△T□□□
MHQ0603P22N△T□□□
MHQ0603P24N△T□□□
MHQ0603P27N△T□□□
MHQ0603P30N△T□□□
MHQ0603P33N△T□□□
MHQ0603P36N△T□□□
MHQ0603P39N△T□□□
The " △ " of the Part Number contains the inductance tolerance code, B（±0.1nH）, C（±0.2nH）, S（±0.3nH）, G（±2%）, H（±3%）or J（±5%）.
The " □□□ " of the Part Number contains the internal code.
○ Measurement equipment
Product No.
Manufacturer
4291B+16193A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130929 / inductor_high-frequency_mhq_en.fm
(10/17)
I
N
D
U
C
T
O
R
S
MHQ-Pseries MHQ0603PType
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
100
39N
27N
22N
33N
18N
15N
12N
10N
8N2
10
6N8
5N6
Inductance (nH)
4N7
3N9
3N3
2N7
2N2
1N8
1N5
1N2
1
0
1N0
1
10
100
Frequency (MHz)
1000
10000
○ Measurement equipment
Product No.
Manufacturer
E4991+16193A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130929 / inductor_high-frequency_mhq_en.fm
(11/17)
I
N
D
U
C
T
O
R
S
MHQ-Pseries MHQ0603P Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
100
1N0
1N2
90
80
1N8
1N5
2N2
2N7
70
4N7
3N9
3N3
60
5N6
Q
6N8
50
8N2
10N
40
12N
30
15N
18N
20
22N
10
27N
39N
0
1
10
100
Frequency (MHz)
1000
33N
10000
○ Measurement equipment
Product No.
Manufacturer
E4991+16193A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130929 / inductor_high-frequency_mhq_en.fm
(12/17)
I
N
D
U
C
T
O
R
S
MHQ-Pseries
MHQ1005P Type
0.60±0.05
SHAPE & DIMENSIONS
0.12±0.05
0.12±0.05
0.50±0.10
1.00±0.05
0.22±0.08
Dimensions in mm
0.22±0.08
0.65
RECOMMENDED LAND PATTERN
0.35
0.50
0.35
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20130929 / inductor_high-frequency_mhq_en.fm
(13/17)
I
N
D
U
C
T
O
R
S
MHQ-Pseries MHQ1005P Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
L
(nH)
1.0
1.1
1.2
1.3
1.5
1.6
1.8
2.0
2.2
2.4
2.7
3.0
3.3
3.6
3.9
4.3
4.7
5.1
5.6
6.2
6.8
7.5
8.2
9.1
10
12
15
Tolerance
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±0.1, ±0.2, 0.3nH
±2%, ±3%, ±5%
±2%, ±3%, ±5%
±2%, ±3%, ±5%
±2%, ±3%, ±5%
±2%, ±3%, ±5%
±2%, ±3%, ±5%
±2%, ±3%, ±5%
Self-resonant
L measuring
Q measuring
frequency
Q
frequency
frequency
(GHz)
min.
(MHz)
(MHz)
min.
typ.
100
—
250
15.0
20.0
100
—
250
14.0
20.0
100
—
250
13.0
18.3
100
—
250
12.0
20.0
100
23
250
11.0
19.7
100
23
250
10.0
15.2
100
23
250
9.0
15.1
100
23
250
8.0
11.5
100
23
250
8.0
12.1
100
23
250
6.5
9.8
100
23
250
6.5
9.6
100
23
250
6.0
9.4
100
23
250
6.0
9.0
100
23
250
5.5
8.4
100
23
250
5.0
7.7
100
23
250
5.0
7.1
100
23
250
5.0
7.7
100
23
250
4.5
7.2
100
23
250
4.5
6.5
100
23
250
4.0
5.9
100
23
250
4.0
5.8
100
23
250
4.0
5.6
100
23
250
3.6
4.9
100
23
250
3.4
4.5
100
23
250
3.3
4.6
100
23
250
2.8
3.8
100
23
250
2.3
3.2
DC resistance
(: )
max.
0.03
0.03
0.03
0.03
0.04
0.04
0.04
0.05
0.06
0.06
0.07
0.08
0.08
0.09
0.09
0.10
0.11
0.12
0.13
0.13
0.14
0.16
0.16
0.17
0.19
0.24
0.28
typ.
0.01
0.02
0.01
0.01
0.02
0.02
0.03
0.03
0.04
0.04
0.04
0.06
0.06
0.07
0.07
0.08
0.08
0.09
0.10
0.09
0.10
0.12
0.12
0.13
0.15
0.19
0.22
Rated current
Part No.*
(mA)
max.
1200
1200
1200
1200
1000
1000
1000
1000
1000
1000
900
900
900
900
900
800
800
800
800
700
700
600
550
550
500
450
400
MHQ1005P1N0△T□□□
MHQ1005P1N1△T□□□
MHQ1005P1N2△T□□□
MHQ1005P1N3△T□□□
MHQ1005P1N5△T□□□
MHQ1005P1N6△T□□□
MHQ1005P1N8△T□□□
MHQ1005P2N0△T□□□
MHQ1005P2N2△T□□□
MHQ1005P2N4△T□□□
MHQ1005P2N7△T□□□
MHQ1005P3N0△T□□□
MHQ1005P3N3△T□□□
MHQ1005P3N6△T□□□
MHQ1005P3N9△T□□□
MHQ1005P4N3△T□□□
MHQ1005P4N7△T□□□
MHQ1005P5N1△T□□□
MHQ1005P5N6△T□□□
MHQ1005P6N2△T□□□
MHQ1005P6N8△T□□□
MHQ1005P7N5△T□□□
MHQ1005P8N2△T□□□
MHQ1005P9N1△T□□□
MHQ1005P10N△T□□□
MHQ1005P12N△T□□□
MHQ1005P15N△T□□□
The " △ " of the Part Number contains the inductance tolerance code, B（±0.1nH）, C（±0.2nH）, S（±0.3nH）, G（±2%）, H（±3%）or J（±5%）.
The " □□□ " of the Part Number contains the internal code.
・ Short bar residual inductance =0.556nH
○ Measurement equipment
Measurement item
Product No.
L, Q
4291B+16193A
Self-resonant frequency
8720C
DC resistance
Type-7561
＊ Equivalent measurement equipment may be used.
Manufacturer
Agilent Technologies
Agilent Technologies
Yokogawa
• All specifications are subject to change without notice.
001-01 / 20130929 / inductor_high-frequency_mhq_en.fm
(14/17)
I
N
D
U
C
T
O
R
S
MHQ-Pseries MHQ1005P Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
L(nH)typ.
500MHz
1.0
1.1
1.2
1.3
1.5
1.6
1.8
2.0
2.2
2.3
2.6
2.9
3.2
3.5
3.8
4.2
4.6
5.0
5.5
6.1
6.7
7.3
8.0
8.9
9.8
12
15
800MHz
1.0
1.1
1.2
1.3
1.5
1.6
1.8
2.0
2.1
2.3
2.6
2.9
3.2
3.5
3.8
4.2
4.6
5.0
5.5
6.1
6.7
7.3
8.1
9.0
9.9
12
15
1.8GHz
1.0
1.1
1.2
1.3
1.5
1.6
1.8
2.0
2.2
2.4
2.7
3.0
3.3
3.6
3.9
4.4
4.7
5.2
5.7
6.5
7.2
7.9
8.9
9.9
11.1
14
18
2.0GHz
1.0
1.1
1.2
1.3
1.5
1.6
1.8
2.0
2.2
2.4
2.7
3.0
3.3
3.6
4.0
4.5
4.8
5.3
5.8
6.7
7.4
8.1
9.2
10.3
11.6
14
20
2.4GHz
1.0
1.1
1.2
1.3
1.5
1.6
1.8
2.0
2.2
2.4
2.7
3.1
3.4
3.7
4.1
4.6
4.9
5.4
6.1
7.0
7.8
8.5
9.8
11.2
12.6
16
23
Q typ.
500MHz
56min.
56min.
56min.
56min.
56
60
52
54
47
45
45
47
41
41
40
41
38
41
39
45
42
38
42
38
39
39
37
800MHz
76min.
76min.
76min.
76min.
76
78
72
70
62
59
57
59
55
53
53
54
50
52
51
56
53
49
53
49
51
49
45
1.8GHz
126min.
126min.
126min.
126min.
126
136
123
108
104
98
87
92
91
87
87
86
82
79
81
84
77
76
77
73
74
67
57
2.0GHz
130min.
130min.
130min.
130min.
130
144
129
113
110
102
91
97
95
91
91
89
85
83
84
87
80
79
80
75
75
68
57
2.4GHz
160min.
160min.
160min.
160min.
160
174
152
132
129
120
108
116
112
107
105
102
98
97
95
99
91
87
88
79
77
70
54
Part No.*
MHQ1005P1N0△T□□□
MHQ1005P1N1△T□□□
MHQ1005P1N2△T□□□
MHQ1005P1N3△T□□□
MHQ1005P1N5△T□□□
MHQ1005P1N6△T□□□
MHQ1005P1N8△T□□□
MHQ1005P2N0△T□□□
MHQ1005P2N2△T□□□
MHQ1005P2N4△T□□□
MHQ1005P2N7△T□□□
MHQ1005P3N0△T□□□
MHQ1005P3N3△T□□□
MHQ1005P3N6△T□□□
MHQ1005P3N9△T□□□
MHQ1005P4N3△T□□□
MHQ1005P4N7△T□□□
MHQ1005P5N1△T□□□
MHQ1005P5N6△T□□□
MHQ1005P6N2△T□□□
MHQ1005P6N8△T□□□
MHQ1005P7N5△T□□□
MHQ1005P8N2△T□□□
MHQ1005P9N1△T□□□
MHQ1005P10N△T□□□
MHQ1005P12N△T□□□
MHQ1005P15N△T□□□
The " △ " of the Part Number contains the inductance tolerance code, B（±0.1nH）, C（±0.2nH）, S（±0.3nH）, G（±2%）, H（±3%）or J（±5%）.
The " □□□ " of the Part Number contains the internal code.
○ Measurement equipment
Product No.
Manufacturer
4291B+16193A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130929 / inductor_high-frequency_mhq_en.fm
(15/17)
I
N
D
U
C
T
O
R
S
MHQ-Pseries MHQ1005PType
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
1000
100
15N
Inductance(nH)
12N
10N
8N2
10
6N8
5N6
4N7
3N9
3N3
2N7
2N2
1N8
1N5
1N2
1N0
1
0
10
100
1000
10000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991+16193A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130929 / inductor_high-frequency_mhq_en.fm
(16/17)
I
N
D
U
C
T
O
R
S
MHQ-Pseries MHQ1005P Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
200
1N2
1N0
1N5
1N8
180
160
2N2
140
2N7
3N3
3N9
120
4N7
Q
5N6
100
6N8
8N2
80
10N
60
12N
40
15N
20
0
10
100
1000
10000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991+16193A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130929 / inductor_high-frequency_mhq_en.fm
(17/17)
I
N
D
U
C
T
O
R
S
MHQ-Pseries
Packaging Style
REEL DIMENSIONS
ø60min.
1.0
2.0±0.5
8.4 +2.0
–0.0
ø13±0.2
14.4max.
ø21±0.8
ø180±2.0
Dimensions in mm
3.5±0.05
Cavity
Type
MHQ0603P
MHQ1005P
A
0.74±0.05
1.15±0.10
B
0.44±0.05
0.75±0.10
K
0.60 max.
0.8 max.
A
8.0±0.3
Sprocket hole
1.5 +0.1
–0.0
1.75±0.1
TAPE DIMENSIONS
K
B
4.0±0.1
2.0±0.05
160min.
Taping
2.0±0.05
200min.
Drawing direction
300min.
• All specifications are subject to change without notice.
001-01 / 20130929 / inductor_high-frequency_mhq_en.fm