ICROCLOCK MK1711-01 200 MHz Selectable Clock Source Description Features The MK1711-01 is a low cost, low jitter, high performance, high speed PLL clock synthesizer designed for high-frequency applications. Using MicroClock’s analog and digital Phase-Locked Loop (PLL) techniques, the device uses an inexpensive 20 MHz crystal to generate a highquality output clock up to 200MHz. • Packaged in 16 pin narrow SOIC • Uses an inexpensive 20.0 MHz crystal • Eight selectable frequencies up to 200 MHz • Duty cycle of 50% typical • +3.3V operating voltage • 25mA output drive capability at TTL levels • Compatible with TI DSP devices MicroClock manufactures the largest variety of clock synthesizers for all applications. Consult MicroClock to eliminate crystals and oscillators from your board. Block Diagram VDD VDDP 3 S2:0 PLL/Clock Synthesis Circuitry X1 20 MHz crystal Output Buffer CLK Crystal Oscillator X2 Output Enable 1 Revision 12087 Printed 12/8/97 MicroClock Division of ICS•1271 Parkmoor Ave.•San Jose•CA•95126•(408)295-9800tel•(408)295-9818fax MDS1711-01B ICROCLOCK MK1711-01 200 MHz Selectable Clock Source Pin Assignment MK1711-01 X1 VDD VDD VDDP GND GND SEL3V INVCLK 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 Output Clock Select Table (MHz) X2 OE NC CLK NC S0 S1 S2 Input 20 20 20 20 20 20 20 20 S2 0 0 0 0 1 1 1 1 S1 0 0 1 1 0 0 1 1 S0 0 1 0 1 0 1 0 1 CLK1 200 182 167 154 143 133 125 118 16 pin narrow (150 mil) SOIC Pin Descriptions Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Name X1 VDD VDD VDDP GND GND SEL3V INVCLK S2 S1 S0 NC CLK NC OE X2 Type XI P P P P P I I I I I O I XO Description Crystal connection. Connect to a 20.00 MHz crystal. VDD. Connect to +3.3V (Possibly 5V). VDD. Connect to +3.3V (Possibly 5V). Connect to 3.3V only. Connect to ground. Connect to ground. Select 3.3V only power supply. Connect to GND for VDD=5V. Internal pull-up. Inverts output clock. Internal pull-up. Clock Select 2. Selects output per table above. Internal pull-up. Clock Select 1. Selects output per table above. Internal pull-up. Clock Select 0. Selects output per table above. Internal pull-up. No Connect. Nothing is connected internally to this pin. Clock output determined by status of S2, S1, S0. See table above. No Connect. Nothing is connected internally to this pin. Output Enable. Active high. Tri-states clock output when low. Internal pull-up. Crystal connection. Connect to a 20.00 MHz crystal. Key: I = Input, O = output, P = power supply connection 2 Revision 12087 Printed 12/8/97 MicroClock Division of ICS•1271 Parkmoor Ave.•San Jose•CA•95126•(408)295-9800tel•(408)295-9818fax MDS1711-01B ICROCLOCK MK1711-01 200 MHz Selectable Clock Source Electrical Specifications Parameter Conditions Minimum Typical Maximum Units 7 VDD+0.5 70 260 150 V V °C °C °C 5.25 0 V V V V V V V V mA mA pF ppm ±50 0.6 0.6 55 ±350 MHz ppm ns ns % ps ABSOLUTE MAXIMUM RATINGS (note 1) Supply voltage, VDD Inputs and Clock Outputs Ambient Operating Temperature Soldering Temperature Storage temperature Referenced to GND Referenced to GND -0.5 0 Max of 10 seconds -65 DC CHARACTERISTICS (VDD = 5.0V unless noted) Operating Voltage, VDD Input High Voltage, VIH, X1 pin only Input Low Voltage, VIL, X1 pin only Input High Voltage, VIH Input Low Voltage, VIL Output High Voltage, VOH Output Low Voltage, VOL Output High Voltage, VOH, CMOS level Operating Supply Current, IDD Short Circuit Current Input Capacitance Frequency synthesis error 3.00 3.5 2.5 2.5 1.5 2 0.8 IOH=-50mA IOL=50mA IOH=-16mA No Load, note 2 2.4 0.4 VDD-0.4 8 TBD 7 S2, S1, S0, OE All clocks AC CHARACTERISTICS (VDD = 5.0V unless noted) Input Crystal Frequency Input Crystal Accuracy Output Clock Rise Time, 200 MHz Output Clock Fall Time, 200MHz Output Clock Duty Cycle Maximum Absolute Jitter, short term Notes: 20.00000 0.8 to 2.0V 2.0 to 0.8V At VDD/2 45 200 1. Stresses beyond those listed under Absolute Maximum Ratings could cause permanent damage to the device. Prolonged exposure to levels above the operating limits but below the Absolute Maximums may affect device reliability. 2. With VDD at 3.3V and CLK at 200MHz. External Components The MK1711-01 requires a minimum number of external components for proper operation. Decoupling capacitors of 0.1µF should be connected between VDD and GND (pins 3 and 5), as close to the MK171101 as possible. A series termination resistor of 33Ω may be used for the clock output. The input crystal must be connected as close to the chip as possible. The input crystal should be a parallel mode, 20 MHz fundamental, with 20pF load capacitance. 3 Revision 12087 Printed 12/8/97 MicroClock Division of ICS•1271 Parkmoor Ave.•San Jose•CA•95126•(408)295-9800tel•(408)295-9818fax MDS1711-01B ICROCLOCK Package Outline and Package Dimensions E 16 pin SOIC narrow Symbol A b c D E H e h Q H h x 45° D c Q e MK1711-01 200 MHz Selectable Clock Source Inches Min Max 0.055 0.070 0.013 0.019 0.007 0.010 0.385 0.400 0.150 0.160 0.225 0.245 .050 BSC 0.016 0.004 0.01 Millimeters Min Max 1.397 1.778 0.330 0.483 0.190 0.254 9.779 10.160 3.810 4.064 5.715 6.223 1.27 BSC 0.406 0.102 0.254 A b Ordering Information Part/Order Number MK1711-01S MK1711-01STR Marking MK1711-01S MK1711-01S Shipping packaging tubes tape and reel Package 16 pin SOIC 16 pin SOIC Temperature 0-70°C 0-70°C While the information presented herein has been checked for both accuracy and reliability, MicroClock Incorporated assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by MicroClock. MicroClock reserves the right to change any circuitry or specifications without notice. MicroClock does not authorize or warrant any MicroClock product for use in life support devices or critical medical instruments. 4 Revision 12087 Printed 12/8/97 MicroClock Division of ICS•1271 Parkmoor Ave.•San Jose•CA•95126•(408)295-9800tel•(408)295-9818fax MDS1711-01B