MK3732-17 ADSL VCXO CLOCK SOURCE Description Features The MK3732-17 is a low cost, low jitter, high performance VCXO and PLL clock synthesizer designed to replace expensive VCXO modules and oscillators. The on-chip Voltage Controlled Crystal Oscillator (VCXO) accepts a 0 to 3.3 V input voltage to cause the output clocks to vary by +100 ppm. Using ICS’ patented VCXO and analog Phase-Locked Loop (PLL) techniques, the device uses an inexpensive pullable crystal input to produce one or two output clocks. • Packaged in 16 pin (150 mil) SOIC • Replaces a VCXO and oscillator • Ideal for Asymmetrical Digital Subscriber Line The MK3732-17 is an upgrade to the MK3732-07, and is recomended for new designs. 12 mA output drive capability at TTL levels (ADSL) chipsets • Uses an inexpensive pullable crystal • On-chip patented VCXO with pull range of 200 ppm (+ 100 ppm) minimum • • • • • ICS manufactures the largest variety of xDSL clock synthesizers for all applications. Consult ICS to eliminate VCXOs, crystals, and oscillators from your board. VCXO tuning voltage of 0 to 3.3 V Advanced, low power, sub-micron CMOS process Operating voltage of 3.3V Industrial temperature range available Block Diagram VDD 2 3 S2:S0 CLK1 VIN X1 Pullable Crystal X2 Voltage Controlled Crystal Oscillator PLL/ Clock Synthesis Circuitry CLK2 2 GND OE MDS 3732-17 D 1 Revision 050803 Integrated Circuit Systems, Inc. ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com MK3732-17 ADSL VCXO CLOCK SOURCE Pin Assignment Clock Select Table S2 S1 S0 Input CLK1 CLK2 X2 1 16 S1 0 0 0 13.248 35.328 29.4 X1 2 15 DC 0 0 M 13.248 35.328 47.1 VD D 3 14 GND 0 0 1 13.248 35.328 40.4 VIN 4 13 VDD 0 1 0 13.248 42.4 35.328 NC 5 12 NC 0 1 M 17.664 24.73 35.328 GND 6 11 S0 0 1 1 17.664 35.328 OFF C LK1 7 10 OE 1 0 0 23.552 49.46 35.328 C LK2 8 9 S2 1 0 M 17.664 49.46 35.328 1 0 1 13.248 35.328 Off 1 1 0 13.248 2.208 Off 1 1 M 13.248 24.73 35.328 1 1 1 13.248 49.46 35.328 16 Pin (150 m il) SO IC 0=connect directly to GND M=leave unconnected (floating) 1=connect directly to VDD Pin Descriptions Pin Number Pin Name Pin Type 1 X2 Input Crystal connection. Connect to a pullable crystal. See table above. 2 X1 Input Crystal connection. Connect to a pullable crystal. See table above. 3 VDD Power 4 VIN Input Voltage input to VCXO. Zero to 3.3V signal which controls the VCXO frequency. 5 NC -- No Connect. Okay to connect to VDD or GND (to match MK3732-07). 6 GND Power Connect to ground. 7 CLK1 Output Clock output #1 per table above. 8 CLK2 Output Clock output #2 per table above. 9 S2 Input Select input #2. Selects outputs per table above. Internal pull-up resistor. 10 OE Input Output enable. Tri-states outputs when low. Internal pull-up resistor. 11 S0 Input Select input #0. Selects outputs per table above. 12 NC -- 13 VDD Power Connect to +3.3V. 14 GND Power Connect to ground. 15 DC - 16 S1 Input MDS 3732-17 D Pin Description Connect to +3.3V. No Connect. Okay to connect to VDD or GND (to match MK3732-07). Don’t connect. Do not connect anything to this pin. Select input #1. Selects outputs per table above. 2 Revision 050803 Integrated Circuit Systems, Inc. ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com MK3732-17 ADSL VCXO CLOCK SOURCE External Component Selection Crystal Tuning Load Capacitors The MK3732-17 requires a minimum number of external components for proper operation. The crystal traces should include pads for small fixed capacitors, one between X1 and ground, and another between X2 and ground. Stuffing of these capacitors on the PCB is optional. The need for these capacitors is determined at system prototype evaluation, and is influenced by the particular crystal used (manufacture and frequency) and by PCB layout. The typical required capacitor value is 1 to 4 pF. Decoupling Capacitors Decoupling capacitors of 0.01µF should be connected between VDD and GND on pins 3 and 6, and on pins 13 and 14, as close to the MK3732-17 as possible. For optimum device performance, the decoupling capacitors should be mounted on the component side of the PCB. Avoid the use of vias in the decoupling circuit. Series Termination Resistor When the PCB traces between the clock outputs and the loads are over 1 inch, series termination should be used. To series terminate a 50Ω trace (a commonly used trace impedance) place a 33Ω resistor in series with the clock line, as close to the clock output pin as possible. The nominal impedance of the clock output is 20Ω. Quartz Crystal The MK3732-17 VCXO function consists of the external crystal and the integrated VCXO oscillator circuit. To assure the best system performance (frequency pull range) and reliability, a crystal device with the recommended parameters must be used, and the layout guidelines discussed in the following section must be followed. The frequency of oscillation of a quartz crystal is determined by its “cut” and by the load capacitors connected to it. The MK3732-17 incorporates on-chip variable load capacitors that “pull” (change) the frequency of the crystal. The crystal specified for use with the MK3732-17 is designed to have zero frequency error when the total of on-chip + stray capacitance is 14pF. The external crystal must be connected as close to the chip as possible and should be on the same side of the PCB as the MK3732-17. There should be no vias between the crystal pins and the X1 and X2 device pins. There should be no signal traces underneath or close to the crystal. To determine the need for and value of the crystal adjustment capacitors, you will need a PC board of your final layout, a frequency counter capable of about 1 ppm resolution and accuracy, two power supplies, and some samples of the crystals which you plan to use in production, along with measured initial accuracy for each crystal at the specified crystal load capacitance, CL. To determine the value of the crystal capacitors: 1. Connect VDD of the MK3732-17 to 3.3V. Connect pin 4 of the MK3732-17 to the second power supply. Adjust the voltage on pin 4 to 0V. Measure and record the frequency of the CLK output. 2. Adjust the voltage on pin 4 to 3.3V. Measure and record the frequency of the same output. To calculate the centering error: 6 ( f 3.3V – f t arg et ) + ( f 0V – f t arg et ) Error = 10 x ------------------------------------------------------------------------------ – errorxtal ft arg et Where: ftarget = nominal crystal frequency errorxtal =actual initial accuracy (in ppm) of the crystal being measured If the centering error is less than ±25 ppm, no adjustment is needed. If the centering error is more than 25ppm negative, the PC board has excessive stray capacitance and a new PCB layout should be considered to reduce stray capacitance. (Alternately, the crystal may be re-specified to a higher load capacitance. Contact ICS for details.) If the centering error is more than 25ppm positive, add identical fixed centering capacitors from each crystal pin to ground. The value for each of these caps (in pF) is given by: Please see application note MAN05 for recommended crystal parameters and suppliers. MDS 3732-17 D 3 Revision 050803 Integrated Circuit Systems, Inc. ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com MK3732-17 ADSL VCXO CLOCK SOURCE External Capacitor = assume it is 30 ppm/pF. After any changes, repeat the measurement to verify that the remaining error is acceptably low (typically less than ±25ppm). 2 x (centering error)/(trim sensitivity) Trim sensitivity is a parameter which can be supplied by your crystal vendor. If you do not know the value, Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the MK3732-17. These ratings, which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD 7V All Inputs and Outputs -0.5V to VDD+0.5V Ambient Operating Temperature -40 to +85°C Storage Temperature -65 to +150°C Soldering Temperature 260°C Recommended Operation Conditions Parameter Min. Typ. Max. Units Ambient Operating Temperature (MK3732-17SI) -40 +85 °C Ambient Operating Temperature (MK3732-17S) 0 +70 °C +3.15 +3.45 V Power Supply Voltage (measured in respect to GND) Reference crystal parameters Refer to MAN05 DC Electrical Characteristics VDD=3.3V ±5% , Ambient temperature 0 to +70°C, unless stated otherwise Parameter Symbol Conditions Operating Voltage VDD Output High Voltage VOH IOH = -12 mA Output Low Voltage VOL IOL = 12 mA Output High Voltage (CMOS Level) VOH IOH = -8 mA Short Circuit Current IOS Input High Voltage, binary inputs VIH S2, S1, OE Input High Voltage, trinary input V IH S0 MDS 3732-17 D Min. Typ. Max. Units 3.15 3.3 3.45 V 2.4 V 0.4 VDD-0.4 V ±50 4 V mA 2.0 V VDD-0.5 V Revision 050803 Integrated Circuit Systems, Inc. ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com MK3732-17 ADSL VCXO CLOCK SOURCE Parameter Symbol Conditions Min. Typ. Max. Units Input Low Voltage, binary inputs VIL S2, S1, OE 0.8 V Input Low Voltage, trinary input V IL S0 0.5 V Operating Supply Current IDD No load 15 mA Input Capacitance CIN S2:S0, OE 5 pF VIN, VCXO Control Voltage V IA Internal Pull-up Resistor RPU 0 3.3 S2:S0, OE V 430 kΩ AC Electrical Characteristics VDD = 3.3V ±5%, Ambient Temperature 0 to +70° C, unless stated otherwise Parameter Symbol Conditions Min. Typ. Max. Units Input Crystal Frequency 13.248 MHz Output Clock Frequency See Table on Page 2 MHz Output Clock Rise Time tOR 0.8 to 2.0V, Note 1 1.5 ns Output Clock Fall Time tOF 2.0 to 0.8V, Note 1 1.5 ns Output Clock Duty Cycle tD At VDD/2, Note 1 60 % Maximum Absolute Jitter tj Note 1, deviation from mean ±150 ps Phase Noise, relative to carrier 10 kHz offset -124 dBc/Hz Frequency Synthesis Error Both clocks VCXO Pullability FP VCXO Gain 40 0 0V < VIN < 3.3V, Note 2 ±100 VIN = (VDD/2)±1, Note 2 ppm ppm 150 ppm/V Note 1: Measured with a 15 pF load. Note 2: External pullable crystal must conform with those listed in application note MAN05 Thermal Characteristics Parameter Thermal Resistance Junction to Ambient Thermal Resistance Junction to Case MDS 3732-17 D Symbol Conditions Min. Typ. Max. Units θJA Still air 120 °C/W θJA 1 m/s air flow 115 °C/W θJA 3 m/s air flow 105 °C/W 58 °C/W θJC 5 Revision 050803 Integrated Circuit Systems, Inc. ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com MK3732-17 ADSL VCXO CLOCK SOURCE Package Outline and Package Dimensions (16 pin SOIC, 150 Mil. Narrow Body) Package dimensions are kept current with JEDEC Publication No. 95 Millimeters 16 Symbol E Min A A1 B C D E e H h L α H INDEX AREA 1 2 D A Inches Max Min 1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 9.80 10.00 3.80 4.00 1.27 BASIC 5.80 6.20 0.25 0.50 0.40 1.27 0° 8° Max .0532 .0688 .0040 .0098 .013 .020 .0075 .0098 .3859 .3937 .1497 .1574 0.050 BASIC .2284 .2440 .010 .020 .016 .050 0° 8° h x 45 A1 C -Ce SEATING PLANE B α L .10 (.004) C Ordering Information Part / Order Number Marking Shipping packaging Package Temperature MK3732-17S MK3732-17STR MK3732-17SI MK3732-17SITR MK3732-17S MK3732-17S MK3732-17SI MK3732-17SI Tubes Tape and Reel Tubes Tape and Reel 16 pin SOIC 16 pin SOIC 16 pin SOIC 16 pin SOIC 0 to +70° C 0 to +70° C -40 to +85° C -40 to +85° C While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. MDS 3732-17 D 6 Revision 050803 Integrated Circuit Systems, Inc. ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com