MLX90401 Brushless DC Motor Controller Features and benefits • 12V to 40V operating range • BVDSS > 60V • On-chip “boost” voltage allows use of all N-channel drivers • On-chip PWM oscillator • PWM speed control via bottom drivers • Forward and reverse control • Selectable 60° or 120° sensor electrical phasing • Undervoltage lockout • Qualified for automotive applications Ordering information Part No. Temperature Code Package Code MLX90401 K (-40°C to 125°C) DF (300” SOIC24) Application examples • Handheld Battery powered applications: o Power tools (drills, screwdrivers, etc.) • Electrical bicycles, wheelchairs, etc. • Automotive applications: o Manual HVAC Blowers o Water and other pumps 1 Pin configuration 1 Supply Voltage 2 2 General description Cap Boost "A" 24 VREF Out Gate Top "A" 23 3 Hall "A" Input Feedback "A" 22 4 Hall "B" Input Cap Boost "B" 21 5 Hall "C" Input Gate Top "B" 20 6 Fwd/Rev Input Feedback "B" 19 7 Speed Adjust Input / Disable Cap Boost "C" 18 8 Oscillator R/C Gate Top "C" 17 9 /Brake Input 10 Analog Ground Feedback "C" 16 Gate Bottom "A" 15 11 60°/120° Select Input Gate Bottom "B" 14 12 Power Ground Gate Bottom "C" 13 Figure 1: Pin configuration 3901090401 Rev 005 The MLX90401 is a three-phase brushless DC motor controller, designed to meet the needs of high volume, low cost motors with 60o or 120° electrical sensor phasing which do not require the expensive options needed for servo or other closed loop applications. The use of CMOS technology offers dense logic as well as high voltage (60V) driver capabilities. The use of discrete low cost N-channel power FETs reduces overall system cost and the device provides all of the logic necessary to interface Hall-effect position sensors to Nchannel power FETs. Upper N-channel power FETs require a gate drive in excess of the supply voltage V+, and with the device’s on-chip “boost” voltage, the use of all N-Channel power FETs is allowed. Control inputs are provided for motor speed, forward or reverse direction, disable, and braking. 60° or 120° electrical sensor phasing can be set externally. The device is offered in a 24 Lead Wide Body SOIC package (DF). Page 1 of 13 Data sheet Oct/05 MLX90401 Brushless DC Motor Controller Table of content 1 Pin configuration ..........................................................................................................1 2 General description ......................................................................................................1 3 Glossary of terms .........................................................................................................3 4 Pin definitions and description....................................................................................3 5 Absolute maximum ratings ..........................................................................................4 6 MLX90401 electrical specifications .............................................................................4 7 General description ......................................................................................................5 7.1 Overview .............................................................................................................................................. 5 7.2 Block diagram ...................................................................................................................................... 6 7.3 Commutation decoding and output control logic.................................................................................. 7 7.4 Oscillator .............................................................................................................................................. 7 7.5 Disable ................................................................................................................................................. 7 7.6 Pulse width modulation ........................................................................................................................ 8 7.7 Drive outputs ........................................................................................................................................ 8 7.8 Undervoltage lockout ........................................................................................................................... 9 7.9 Logic table ............................................................................................................................................ 9 8 Application information..............................................................................................10 8.1 Evaluation Board................................................................................................................................ 10 8.2 Typical application.............................................................................................................................. 10 9 FAQ ..............................................................................................................................11 9.1 Bootstrap capacitor selection ............................................................................................................. 11 9.2 Motor Noise ........................................................................................................................................ 11 10 Reliability Information ..............................................................................................11 11 ESD Precautions .......................................................................................................12 12 FAQ ............................................................................................................................12 13 Package Information.................................................................................................12 14 Disclaimer..................................................................................................................13 3901090401 Rev 005 Page 2 of 13 Data sheet Oct/05 MLX90401 Brushless DC Motor Controller 3 Glossary of terms FET PWM Field Effect Transistor Pulse Width Modulation Undervoltage State in which the power supply voltage is lower than the operation range of the device. State in which the current flowing in a certain device (e.g. output driver, motor, etc.) exceeds a maximum defined level. This includes both overload and short-circuit currents. Overcurrent 4 Pin definitions and description Pin 1 2 Symbol Supply voltage VREF Out 3-5 Hall "A", "B" and "C" Inputs 6 Fwd/Rev Input 7 Speed Adjust Input/Disable 8 Oscillator R/C 9 /Brake Input 10 11 Analog ground 60°/120° Select Input 12 13-15 16, 19, 22 Power Ground Gate Bottom "A", "B" and "C" Feedback "A", "B" and "C" 17, 20, 23 Gate Top "A", "B" and "C" 18, 22, 24 Cap Boost "A", "B" and "C" Description External power supply voltage. Regulated reference voltage (12V) derived from V+. Used to power external components and Hall-effect sensors, and for boost voltage. Hall IC open collect inputs. Pull-up resistance of 3.3k to 5V. The Forward/Reverse Input is used to change the direction of motor rotation. A logic high state selects forward direction; a logic low state selects reverse direction. Pull-up resistance of 3.3k to 5V. Potentiometer input - adjusts the PWM duty cycle setting current, allowing a manual speed adjustment. Disable input can be used in combination with any type of switch (thermal, Hall, etc.). A logic low on this pin selects the disable function. The Oscillator frequency is set with the values selected for the timing components RRC and CRC. A logic high state at this input allows the motor to run, while a low state causes rapid deceleration. Pull-up resistance of 3.3k to 5V. Ground pin for analog blocks. A logic high state on this pin selects 60° sensor electrical phasing, a logic low state selects 120°. Pull-up resistance of 3.3k to 5V. Ground pin for digital and output drivers. Three push-pull drivers for direct drive of bottom power switch transistors. Negative supply of the top drive circuitry. It is the connection for the negative side of the bootstrap capacitor, the top power FET Source, the bottom power FET Drain, and the Phase C output. Three push-pull drivers for direct drive of top power switch transistors. Positive supply of the top drive circuitry. The boost capacitor is connected between this pin and Feedback. Table 1: Pin definitions and description 3901090401 Rev 005 Page 3 of 13 Data sheet Oct/05 MLX90401 Brushless DC Motor Controller 5 Absolute maximum ratings Parameter Supply Voltage, VDD (operating) Output Voltage on pins Gate & Cap Boost Voltage on Pins 17,18,20,21,23,24 Power Dissipation, PD Operating Temperature Range, TA Storage Temperature Range, TS Absolute maximum value -0.3 to 45V 60V -0.3 to 60V 500mW -40 to 125°C -40 to 125°C Table 2: Absolute maximum ratings 6 MLX90401 electrical specifications DC Operating Parameters TA = -40 oC to 125 oC Parameter. Supply voltage Supply current Output voltage Output current Symbol VDD IDD Test Conditions Operating Operating Voltage reference VREF IREF Undervoltage VUV Oscillator frequency fOSC High state Low state High state input current Low state input current VIH VIL IIH IIL 100% PWM state1 0% PWM1 Disable1 High state input current Low state input current V100%PWM V0%PWM VDISABLE IIHDIS IILDIS Undervoltage Operating Oscillator Operating, ROSC=10kOhm, COSC=5nF Logic inputs (Pins 2-6, 9, 11) Min 8 Typ 12-24 20 Max 44 35 Units V mA 8 12 15 10 V mA 8 22 25 V 28 kHz 1.5 1.0 2.0 V V mA mA 1.0 1.0 %Vref %Vref %Vref mA mA 3.5 Disable input (Pin 7) 64.3 35.7 16 Debouncing Debounce time (60°/120° Select, Fwd/Rev)2 Debounce time (/Brake)2 Delay after start-up3 tdelay1 18 25 35 ms tdelay2 tdelay3 2.0 18.6 3.2 25.6 4.4 35.6 ms ms Output current IOCP 100 uA Charge pumps 1 2 Input levels of the DISABLE pin are defined internally by a resistor tree. tdelay1 and tdelay2 depend on fosc and timing of the signals to be debounced. 60°/120° Select and Fwd/Rev are debounced using a clock with a frequency of 256*fosc. /Brake is debounced using a clock with a frequency of 32*fosc. Debouncing takes between 2 and 3 clock cycles. Typical example for, say 60°/120° Select: 2.5*256*1/fosc = 2.5*256*1/25kHz = 25.6 ms. 3 tdelay3 depends on fosc. Precautions are taken that tdelay3 is always larger than tdelay1, so that there are only output signals when the chip is in the correct state. 3901090401 Rev 005 Page 4 of 13 Data sheet Oct/05 MLX90401 Brushless DC Motor Controller Top output on resistance Bottom output on resistance Rise time Fall time Turn-on propagation delay Turn-off propagation delay RONT RONB tr tf tdon tdoff Leakage current IOFF Drivers ILOAD = 50mA ILOAD = 50mA Top drivers VOUT = 60V 32 32 150 150 300 300 Ohm Ohm ns ns ns ns -10 uA Table 3: MLX90401 electrical specifications 7 General description 7.1 Overview The MLX90401 contains all functions for controlling three-phase brushless DC motors in open loop applications. The MLX90401 supports following control functions: • speed control • forward or reverse rotation • braking • disable The chip contains: • a rotor position decoder for proper commutation sequencing • a voltage reference that supplies power for the sensors • a pulse width modulator (PWM) based on a frequency programmable sawtooth oscillator • three top and three bottom drivers Using a bootstrap/charge pump combination, the MLX90401 also generates a boost voltage to drive the top power FET. In this way the application only uses N-channel power FETS, to reduce overall system cost. The MLX90401 provides commutation from Hall-effect sensors, and can be configured for motors with 60° or 120° sensor electrical phasing, by means of a select pin. Undervoltage lockout is provided. 3901090401 Rev 005 Page 5 of 13 Data sheet Oct/05 MLX90401 Brushless DC Motor Controller 7.2 Block diagram 5V Regulator (To Logic) 12V Regulator (To Boost) VS (1) VREG(internal) UVLO VREF (2) UVLO Sawtooth Oscillator Osc R/C (8) Note: only one channel shown OSC 25kHz (variable) Charge Pump Level Shifter + Speed Adj / Disable (7) Cap Boost (18,21,24) V+ GT (17,20,23) Chop FB (16,19,22) UVLO VREG(internal) Fault + Output Control Logic GB (13,14,15) PWR GND (12) 5V 3.5KΩ Debouncer 5V Commutation Decoding Logic /Brake (9) 5V 60°/120° Select (11) 3.5KΩ Debouncer 5V 3.5KΩ Fwd/Rev (6) Debouncer 3.5KΩ Hall A (3) 3.5KΩ 5V Hall B (4) 5V 3.5KΩ Hall C (5) GND (10) Figure 2 : Block diagram 3901090401 Rev 005 Page 6 of 13 Data sheet Oct/05 MLX90401 Brushless DC Motor Controller 7.3 Commutation decoding and output control logic An internal digital circuit converts the signals from the Hall-effect position sensors into the proper sequencing of top and bottom drive outputs. 60° or 120° sensor electrical phasing can be selected by an external pin (60°/120° Select, pin 11). The Forward/Reverse input (pin 6) is used to change the direction of motor rotation. If the /Brake input (pin 9) is pulled low, bottom drivers are turned on, while top drivers are turned off, thus braking the motor. These six inputs all have internal pull-up resistors (3.3kΩ to 5V). Inputs 60°/120° Select, Fwd/Rev and /Brake are debounced to make sure that the device doesn’t enter the wrong state, due to noise and/or spikes. The fact that these signals are debounced, also means that there is a delay in these signals. Whenever one of the external signals that are debounced is changed, it takes time till the outputs change accordingly (ca. 25ms for the 60°/120° Select and Fwd/Rev inputs, ca. 3ms for /Brake). After start-up, the outputs are disabled for a given time, in order to provide for the time necessary for the debouncing circuits on 60°/120° Select and Fwd/Rev to settle and output the correct signal. (/Brake is debounced with a shorter time so settles a lot sooner.) 7.4 Oscillator The frequency of the internal sawtooth oscillator is set by the values selected for timing components ROSC and COSC (see Figure 4 : Typical application). Capacitor COSC is charged from the Reference Output (Pin 2) through Resistor ROSC and discharged by an internal discharge transistor. The ratio of the ramp peak and valley voltages referred to the Reference Output voltage are typically 0.65V and 0.3V respectively. To provide a good compromise between audible noise and output switching efficiency, an oscillator frequency in the range of 20 to 30 kHz is recommended. 7.5 Disable Pin 7, Speed Adjust Input/Disable, is to be connected to an external potentiometer, used to set motor speed. The input can also be used as a Disable input, turning off all output drivers. This Disable input can be used in many ways. A thermal switch could be used to provide thermal protection. Or a Hall switch could be used to provide protection against overcurrent, etc. Disable has a higher priority than /Brake. If for instance Disable is active, braking will not have any effect. If /Brake is active at the moment that Disable is made active, all braking will be stopped. 3901090401 Rev 005 Page 7 of 13 Data sheet Oct/05 MLX90401 Brushless DC Motor Controller 7.6 Pulse width modulation The use of pulse width modulation (PWM) provides an energy efficient method of controlling the motor speed by varying the average voltage applied to each stator winding during the commutation sequence. As COSC discharges, the oscillator allows conduction of the top and bottom drive outputs. The PWM comparator terminates the bottom drive output conduction when the positive-going ramp of COSC becomes greater than the Speed Adjust Input. In order to minimize dissipation in the internal diodes of the external top switch transistors, due to free-wheeling currents, the PWM acts also on the top FET, by turning it on when the corresponding bottom FET is off. The pulse width modulator timing diagram is shown below. (Braking of the motor does not depend on the PWM setting. It is always done at 100%.) PWM Timing Diagram (note 1) RC Input VSpeed Input Osc Top Drive Output Bottom Drive Output Note 1. Top and Bottom Drive Output Diagrams assume commutation logic gives 1 for bottom switch and 0 for top switch. In case the commutation logic gives 0 for bottom switch and 1 for top switch, the PWM does not act on them. Figure 3: PWM timing diagram 7.7 Drive outputs The bottom drivers consist of a push-pull driver between the 12V reference voltage and ground. The top drivers use an improved push-pull architecture to guarantee proper drive of the top FETs. Because the top driver utilizes a bootstrap/charge pump combination, use of only N-channel power FETs for the three-phase bridge is possible. This leads to a reduced system cost. Internal charge pumps precharge the boost capacitors to ensure full drive of upper power FETs at start-up. During normal operation, boost is maintained with an external diode and capacitor. The charge pumps compensate for potential leakage currents, in order to ensure that the upper power FETs are driven properly at all time. 3901090401 Rev 005 Page 8 of 13 Data sheet Oct/05 MLX90401 Brushless DC Motor Controller 7.8 Undervoltage lockout Should the voltage level on VDD drop below the undervoltage level, all gate drives will be turned off until the undervoltage condition disappears, to prevent improper drive of the power FETs. 7.9 Logic table Following table shows the output state in function of the inputs. It summarizes the different functions of the MLX90401. SA = Hall Sensor input A, … Inputs Outputs Sensor Electrical Phasing Fwd/ Rev /Brake SA SB SC SA SB SC /Disable Motor position TA TB TC BA BB BC PA PB 0° 0 0 0 1 0 1 1 1 1 1 0 0 0 1 0 ^ v - 60° 1 0 0 1 0 0 1 1 1 1 0 0 0 0 1 ^ - v 120° 1 1 0 1 1 0 1 1 1 0 1 0 0 0 1 - ^ v 180° 1 1 1 0 1 0 1 1 1 0 1 0 1 0 0 v ^ - 240° 0 1 1 0 1 1 1 1 1 0 0 1 1 0 0 v - ^ 300° 0 0 1 0 0 1 1 1 1 0 0 1 0 1 0 - v ^ 0° 0 0 0 1 0 1 0 1 1 0 1 0 1 0 0 v ^ - 300° 0 0 1 0 0 1 0 1 1 0 1 0 0 0 1 - ^ v 240° 0 1 1 0 1 1 0 1 1 1 0 0 0 0 1 ^ - v 180° 1 1 1 0 1 0 0 1 1 1 0 0 0 1 0 ^ v - 120° 1 1 0 1 1 0 0 1 1 0 0 1 0 1 0 - v ^ 60° 1 0 0 1 0 0 0 1 1 0 0 1 1 0 0 v - ^ 60° 120° Top Drive Bottom Drive Motor phases PC x x x x x x x 0 1 0 0 0 1 1 1 v v v x x x x x x x x 0 0 0 0 0 0 0 - - - Table 4 : Logic table The phases mentioned in the table are electrical phases as they are generated by the Hall sensors. The difference between a 60 degree motor and a 120 degree motor is shown in the graph below. By manually turning the motor these outputs can easily be found on an oscilloscope. 120 Hall output 1 Apply to Hall A pin Hall output 2 Apply to Hall B pin Apply to Hall C pin Hall output 3 60 Hall output 1 Apply to Hall A pin Hall output 2 Apply to Hall B pin Apply to Hall C pin Hall output 3 3901090401 Rev 005 Page 9 of 13 Data sheet Oct/05 MLX90401 Brushless DC Motor Controller 8 Application information 8.1 Evaluation Board An Evaluation Board for the MLX90401 called EVB90401 is available. The accompanying Application Note describes the Board, and gives extra information concerning the use of the MLX90401 in real-life applications. Consult our website www.melexis.com for more information. 8.2 Typical application Shown below is a typical application of the MLX90401 that could be used for battery-operated power tools. A manual HVAC blower schematic looks similar, but zener DZ1 should be chosen at for instance 18V. SW1 ON/OFF BT1 12V DZ1 14V 5W C1 100n IC1 MLX90401 Supply Voltage Cap Boost "A" 24 VREF Out Gate Top "A" 23 3 Hall "A" Input Feedback "A" 22 4 Hall "B" Input Cap Boost "B" 21 5 Hall "C" Input Gate Top "B" 20 6 Fwd/Rev Input Feedback "B" 19 7 Speed Adjust Input / Disable Cap Boost "C" 18 8 Oscillator R/C Gate Top "C" 17 1 D1 VREF C2 22u/ 25V R1 10k P1 100k 2 C3 100n Speed C4 5nF Disable Fw/Rev Brake C6 47n R4 C7 47n R5 C8 47n M1 Brushless DC Motor Q1 D4 D2 R2 °T R3 C5 100n D3 9 /Brake Input Feedback "C" 16 10 Analog Ground Gate Bottom "A" 15 11 60°/120° Select Input Gate Bottom "B" 14 Power Ground Gate Bottom "C" 13 12 Q2 R6 D5 Q3 R8 60/120 D6 Q4 R7 Q5 R3 ... R8 = 22R Q1 ... Q6 = IRF530 D3 ... D5 = 1N4148 D6 … D8 = 1N4007 Q6 Figure 4 : Typical application This example system is powered by a 12V battery. • DZ1 is a high power zener diode to clamp the battery line when the system is switched off using SW1: motor M1 could generate a voltage on the power line after shut down, causing the power line to rise and potentially exceed the maximum rating of the MLX90401. DZ1 prevents this. Its voltage specification should be chosen a few volt above the maximum rating of the power supply, but obviously not higher than the absolute maximum rating of the MLX90401. It should be a high power device since it has to absorb a lot of energy in a short time. Other components: • C1 decouples the power line and should be placed as close as possible to the MLX90401. • R1/C4 are the external RC for the oscillator. • The VREF line is decoupled with C2 and C3. VREF powers the Hall effect sensors and the speed potentiometer P1. This signal is filtered using R2/C5 to prevent noise of entering the PWM circuit. • A thermal switch is connected to the Disable input to protect the system from overheating: if the temperature exceeds the thermal switch threshold, it switches on, and disables the motor. 3901090401 Rev 005 Page 10 of 13 Data sheet Oct/05 MLX90401 Brushless DC Motor Controller • • • • • • A Forward/Reverse switch is present; the Brake switch could be omitted depending on the application. A jumper or fixed PCB track selects the type of motor (60/120 degrees electrical sensor spacing). D1-3 and C6-8 are the bootstrap diode and capacitor. Q1-6 are the 6 N-channel power FETs. R3-8 smoothen the rise and fall times of the gate signals to reduce EMC emissions. D4-6 are freewheel diodes. 9 FAQ 9.1 Bootstrap capacitor selection When the top side is turned on charge is transferred from the bootstrap capacitor to the gate capacitance of the N-channel power FET. The bootstrap capacitor value is chosen in function of the gate charge of the Nchannel power FETs used. The charge on the bootstrap capacitor should be at least 20 times greater than the gate charge of the power FET. E.g. for the IRF530 N-channel power FET the total gate charge is specified as 26 nC. Therefore: Cboot = 20 x Qgate / Vgate = 20 x Qgate / VREF = 20 x 26 nC / 12 V = 43 nF. A value of 47 nF is chosen. The maximum voltage drop due to the charge transfer at turn-on is: dVgate = dq / Cboot = Qgate / Cboot = 26 nC / 47 nF = 553 mV. Bootstrap capacitors up to 100nF can be applied. 9.2 Motor Noise The MLX90401 defines its switching sequence based on the Hall input sequence and the state of the 60°/120° Select Input. A 120° electrical sensor phasing motor operated with a 60° setting will most likely function, but will generate clearly audible noise. Vice versa a 60° motor will generate noise when operated with a 120° setting. Changing the setting of 60°/120° Select Input should remove the noise. See also paragraph 7.9 Logic table for an explanation how to find out if a motor has 60° or 120° electrical sensor phasing, and how to connect the phases to the MLX90401 Hall sensor inputs. 10 Reliability Information This Melexis device is classified and qualified regarding soldering technology, solderability and moisture sensitivity level, as defined in this specification, according to following test methods: • IPC/JEDEC J-STD-020 Moisture/Reflow Sensitivity Classification For Nonhermetic Solid State Surface Mount Devices (Classification reflow profiles according to table 5-2) • EIA/JEDEC JESD22-A113 Preconditioning of Nonhermetic Surface Mount Devices Prior to Reliability Testing (Reflow profiles according to table 2) • CECC00802 Standard Method For The Specification of Surface Mounting Components (SMDs) of Assessed Quality • EIA/JEDEC JESD22-B106 Resistance to soldering temperature for through-hole mounted devices 3901090401 Rev 005 Page 11 of 13 Data sheet Oct/05 MLX90401 Brushless DC Motor Controller • EN60749-15 Resistance to soldering temperature for through-hole mounted devices • MIL 883 Method 2003 / EIA/JEDEC JESD22-B102 Solderability For all soldering technologies deviating from above mentioned standard conditions (regarding peak temperature, temperature gradient, temperature profile etc) additional classification and qualification tests have to be agreed upon with Melexis. The application of Wave Soldering for SMD’s is allowed only after consulting Melexis regarding assurance of adhesive strength between device and board. Based on Melexis commitment to environmental responsibility, European legislation (Directive on the Restriction of the Use of Certain Hazardous substances, RoHS) and customer requests, Melexis has installed a Roadmap to qualify their package families for lead free processes also. Various lead free generic qualifications are running, current results on request. For more information on manufacturability/solderability see the quality page on our website: http://www.melexis.com/html/pdf/MLXleadfree-statement.pdf. 11 ESD Precautions Electronic semiconductor products are sensitive to Electro Static Discharge (ESD). Always observe Electro Static Discharge control procedures whenever handling semiconductor products. 12 FAQ Consult the Application Note concerning the EVB90401 MLX90401 Evaluation Board for more information. It can be obtained from www.melexis.com. 13 Package Information The MLX90401 will be assembled in a plastic wide body SOIC24 package. DF - 24 Lead Wide Body SOIC 0.32 0.23 7.60 10.65 7.40 10.00 0.51 0.33 1.27 1.27 0.40 0o to 8o 2.65 2.35 15.60 15.20 0.010 min. All dimensions in millimeters Figure 5: Package information 3901090401 Rev 005 Page 12 of 13 Data sheet Oct/05 MLX90401 Brushless DC Motor Controller 14 Disclaimer Devices sold by Melexis are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. Melexis makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Melexis reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with Melexis for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by Melexis for each application. The information furnished by Melexis is believed to be correct and accurate. However, Melexis shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interrupt of business or indirect, special incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of Melexis’ rendering of technical or other services. © 2002 Melexis NV. All rights reserved. For the latest version of this document, go to our website at www.melexis.com Or for additional information contact Melexis Direct: Europe and Japan: Phone: +32 1367 0495 E-mail: [email protected] All other locations: Phone: +1 603 223 2362 E-mail: [email protected] ISO/TS 16949 and ISO14001 Certified 3901090401 Rev 005 Page 13 of 13 Data sheet Oct/05