Fairchild MM74HC125MX 3-state quad buffer Datasheet

Revised February 1999
MM74HC125/MM74HC126
3-STATE Quad Buffers
General Description
The MM74HC125 and MM74HC126 are general purpose
3-STATE high speed non-inverting buffers utilizing
advanced silicon-gate CMOS technology. They have high
drive current outputs which enable high speed operation
even when driving large bus capacitances. These circuits
possess the low power dissipation of CMOS circuitry, yet
have speeds comparable to low power Schottky TTL circuits. Both circuits are capable of driving up to 15 low
power Schottky inputs.
The MM74HC125 require the 3-STATE control input C to
be taken high to put the output into the high impedance
condition, whereas the MM74HC126 require the control
input to be low to put the output into high impedance.
All inputs are protected from damage due to static discharge by diodes to VCC and ground.
Features
■ Typical propagation delay: 13 ns
■ Wide operating voltage range: 2–6V
■ Low input current: 1 µA maximum
■ Low quiescent current: 80 µA maximum (74HC)
■ Fanout of 15 LS-TTL loads
Ordering Code:
Order Number
Package Number
Package Description
M14A
14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150” Narrow Body
M14D
14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
MM74HC125M
MM74HC125SJ
MM74HC125MTC
MTC14
MM74HC125N
14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
N14A
14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide
MM74HC126M
M14A
14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150” Narrow Body
MM74HC126SJ
M14D
14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
MM74HC126MTC
MTC14
MM74HC126N
14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
N14A
14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide
Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code. (Tape and Reel not available in N14A.)
Connection Diagrams
Pin Assignments for DIP, SOIC, SOP and TSSOP
Top View (MM74HC126)
Top View (MM74HC125)
Truth Tables
Inputs
Output
Inputs
Output
A
C
Y
A
C
Y
H
L
H
H
H
H
L
L
L
L
H
L
X
H
Z
X
L
Z
© 1999 Fairchild Semiconductor Corporation
DS005308.prf
www.fairchildsemi.com
MM74HC125/MM74HC126 3-STATE Quad Buffers
September 1983
MM74HC125/MM74HC126
Absolute Maximum Ratings(Note 1)
Recommended Operating
Conditions
(Note 2)
−0.5 to +7.0V
Supply Voltage (VCC)
DC Input Voltage (VIN)
−1.5 to VCC +1.5V
DC Output Voltage (VOUT)
−0.5 to VCC +0.5V
Clamp Diode Current (IIK, IOK)
±20 mA
DC Output Current, per pin (IOUT)
±35 mA
Min Max Units
Power Dissipation (PD)
600 mW
S.O. Package only
500 mW
VIL
VOH
°C
VCC = 2.0V
1000
ns
VCC = 4.5V
500
ns
VCC = 6.0V
400
ns
Note 3: Power Dissipation temperature derating — plastic “N” package: −
12 mW/°C from 65°C to 85°C.
260°C
DC Electrical Characteristics
VIH
−40 +85
Note 2: Unless otherwise specified all voltages are referenced to ground.
(Soldering 10 seconds)
Parameter
V
Note 1: Absolute Maximum Ratings are those values beyond which damage to the device may occur.
Lead Temperature (TL)
Symbol
V
VCC
Input Rise or Fall Times (tr, tf)
−65°C to +150°C
(Note 3)
6
0
(VIN, VOUT)
±70 mA
(ICC)
2
DC Input or Output Voltage
Operating Temperature Range (TA)
DC VCC or GND Current, per pin
Storage Temperature Range (TSTG)
Supply Voltage (VCC)
(Note 4)
Conditions
TA = 25°C
VCC
Typ
TA = −40 to 85°C TA = −40 to 125°C
Guaranteed Limits
Units
Minimum HIGH Level
2.0V
1.5
1.5
1.5
V
Input Voltage
4.5V
3.15
3.15
3.15
V
6.0V
4.2
4.2
4.2
V
Maximum LOW Level
2.0V
0.5
0.5
0.5
V
Input Voltage
4.5V
1.35
1.35
1.35
V
6.0V
1.8
1.8
1.8
V
V
Minimum HIGH Level
VIN = VIH or VIL
2.0V
2.0
1.9
1.9
1.9
Output Voltage
|IOUT| ≤ 20 µA
4.5V
4.5
4.4
4.4
4.4
V
6.0V
6.0
5.9
5.9
5.9
V
|IOUT| ≤ 6.0 mA
4.5V
4.2
3.98
3.84
3.7
V
|IOUT| ≤ 7.8 mA
6.0V
5.7
5.48
5.34
5.2
V
Maximum LOW Level
VIN = VIH or VIL
2.0V
0
0.1
0.1
0.1
V
Output Voltage
|IOUT| ≤ 20 µA
4.5V
0
0.1
0.1
0.1
V
6.0V
0
0.1
0.1
0.1
V
|IOUT| ≤ 6.0 mA
4.5V
0.2
0.26
0.33
0.4
V
|IOUT| ≤ 7.8 mA
6.0V
0.2
0.26
0.33
0.4
V
VIN = VIH or VIL
6.0V
±0.5
±5
±10
µA
VIN = VIH or VIL
VOL
VIN = VIH or VIL
IOZ
Maximum 3-STATE Output
Leakage Current
VOUT = VCC or GND
Cn = Disabled
IIN
Maximum Input Current
VIN = VCC or GND
6.0V
±0.1
±1.0
±1.0
µA
ICC
Maximum Quiescent
VIN = VCC or GND
6.0V
8.0
80
160
µA
Supply Current
IOUT = 0 µA
Note 4: For a power supply of 5V ±10% the worst case output voltages (VOH, and VOL) occur for HC at 4.5V. Thus the 4.5V values should be used when
designing with this supply. Worst case VIH and VIL occur at VCC=5.5V and 4.5V respectively. (The VIH value at 5.5V is 3.85V.) The worst case leakage current
(IIN, ICC, and IOZ) occur for CMOS at the higher voltage and so the 6.0V values should be used.
www.fairchildsemi.com
2
VCC = 5V, TA = 25°C, CL = 45 pF, tr = tf = 6 ns
Typ
Guaranteed
Limit
Units
13
18
ns
RL = 1 kΩ
13
25
ns
Maximum
RL = 1 kΩ
17
25
ns
Output Disable Time from HIGH Level
CL = 5 pF
Maximum
RL = 1 kΩ
18
25
ns
Maximum
RL = 1 kΩ
13
25
ns
Output Disable Time from LOW Level
CL = 5 pF
Symbol
tPHL, tPLH
Parameter
Conditions
Maximum
Propagation Delay Time
tPZH
Maximum
Output Enable Time to HIGH Level
tPHZ
tPZL
Output Enable Time to LOW Level
tPLZ
AC Electrical Characteristics
VCC = 2.0V to 6.0V, CL = 50 pF, tr = tf = 6 ns (unless otherwise specified)
Symbol
Parameter
Conditions
VCC
TA = 25°C
Typ
TA = −40 to 85°C TA = −40 to 125°C
Units
Guaranteed Limits
tPHL, tPLH Maximum Propagation
2.0V
40
100
125
150
ns
Delay Time
4.5V
14
20
25
30
ns
6.0V
12
17
21
25
ns
2.0V
35
130
163
195
ns
4.5V
14
26
33
39
ns
6.0V
12
22
28
39
ns
2.0V
25
125
156
188
ns
4.5V
14
25
31
38
ns
6.0V
12
21
26
31
ns
2.0V
25
125
156
188
ns
4.5V
14
25
31
38
ns
ns
tPLH, tPHL Maximum Propagation
CL = 150 pF
Delay Time
tPZH, tPZL Maximum Output
RL = 1 kΩ
Enable Time
tPHZ, tPLZ Maximum Output
RL = 1 kΩ
Disable Time
tPZL, tPZH Maximum Output
Enable Time
tTLH, tTHL Maximum Output
6.0V
12
21
26
31
CL = 150 pF
2.0V
35
140
175
210
ns
RL = 1 kΩ
4.5V
15
28
35
42
ns
6.0V
13
24
30
36
ns
2.0V
30
60
75
90
ns
4.5V
7
12
15
18
ns
6.0V
6
10
13
15
ns
5
10
10
10
pF
15
20
20
20
pF
CL = 50 pF
Rise and Fall Time
CIN
Input Capacitance
COUT
Output Capacitance Outputs
CPD
Power Dissipation
Capacitance (Note 5)
(per gate)
Enabled
45
pF
Disabled
6
pF
Note 5: CPD determines the no load dynamic power consumption, PD = CPD VCC2f + ICC VCC, and the no load dynamic current consumption,
IS = CPD VCC f + ICC.
3
www.fairchildsemi.com
MM74HC125/MM74HC126
AC Electrical Characteristics
MM74HC125/MM74HC126
Physical Dimensions inches (millimeters) unless otherwise noted
14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150” Narrow Body
Package Number M14A
14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
Package Number M14D
www.fairchildsemi.com
4
MM74HC125/MM74HC126
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
14-Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
Package Number MTC14
5
www.fairchildsemi.com
MM74HC125/MM74HC126 3-STATE Quad Buffers
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide
Package Number N14A
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD
SEMICONDUCTOR CORPORATION. As used herein:
2. A critical component in any component of a life support
1. Life support devices or systems are devices or systems
device or system whose failure to perform can be reawhich, (a) are intended for surgical implant into the
sonably expected to cause the failure of the life support
body, or (b) support or sustain life, and (c) whose failure
device or system, or to affect its safety or effectiveness.
to perform when properly used in accordance with
instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the
www.fairchildsemi.com
user.
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications.
Similar pages