MN102H75K MN102H75K Type MN102HF75K Mask ROM Internal ROM type FLASH ROM (byte) 256K RAM (byte) 8K QFP084-P-1818E Package (Lead-free) Minimum Instruction Execution Time 83 ns (at 3.0 V to 3.6 V, 12 MHz) Interrupts External (6 lines) Internal (30 lines) : Timer × 11, A/D × 1, Undefined command × 1, RESET × 1, OSD × 2, Serial × 4, I²C × 1, Caption × 4, Remote control × 1, Address coincidence × 4 Timer Counter 8-bit timer × 4 16-bit timer × 2 Watchdog timer : 17-bit × 1 Serial interface I²C × 1 : for multimaster mode, bus line (output) has 2 systems Sync serial / I²C (master) / UART × 2 Caption / Teletext Decoder Built-in sync separator × 2 I/O Pins I/O 66 Common use A/D converter 8-bit × 12-ch. (with S/H) D/A converter 4-bit × 4-ch. (analog R, G, B, YM output) PWM 8-bit × 7-ch. Special Ports Remote control reception CRTC 3-layer display (graphics, characters, splits) Notes Remote control input discriminant circuit built-in MAE00015FEM MN102H75K Electrical Charactreistics (D/A converter characteristics) Parameter Symbol D/A full-scale output current D/A output voltage setting range D/A non-linear error Limit Condition min typ IFS 4.5 5.0 VO 0.9 NLE D/A differential non-linear error DNLE D/A channel interval error IFS RL = 200 Ω, VREF = 1.2 V, RIREF = 1.2 kΩ In-circuit Emulator PX-ICE102H75-QFP084-P-1818E 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 NC P71 P10, ADIN5, IRQ1 P11, ADIN6, IRQ2 P12, ADIN7, IRQ3 P72 P13, ADIN8, MDOUT P14, ADIN9, STOP P73 P15, ADIN10, PWM0 P16, ADIN11, PWM1 P17, PWM2 P20, PWM3 P21, PWM4 P22, PWM5 P23, PWM6 P24, TM4IC, SBT1 P25, TM4IOB, SBI1, SBD1 P26, TM4IOA, SBO1 P27, TMO1O P74 Pin Assignment MN102H75K 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 P55, SB00 P54, IRQ5, /VSYNC P84 NC P53, /RST P52, IRQ4 /TEST P51, YS P83 P50, SYSCLK P82 P47, /HSYNC P81 P46, OSDXI P45, OSDXO P44, TM5IC *1 P43, TM5IOB *1 1 P42, TM5IOA * 1 P41, TM1IO * VCOI PDO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 QFP084-P-1818E Note) *1: 5 V dielectric N-ch. open drain output pin *2: MN102H75K (VDD), MN102HF75K (VPP) MAE00015FEM Unit 5.5 mA 1.1 V ±0.5 LSB ±0.5 LSB VREF = 1.2 V, RIREF = 1.2 kΩ, Error from 4-channel % ±5 average IFS (Ta = 25°C , VDD = AVDD = 3.3 V , VSS = 0 V , fosc = 4 MHz) Development tools P70 P07, ADIN4 P06, ADIN3 P05, ADIN2 P04, ADIN1 P03, ADIN0 P02, SCL1 *1 P01, SDA1 *1 P00, RMIN, IRQ0 P87 VSS OSC2 OSC1 VDD P61, SCL0 *1 P86 P60, SDA0 *1 P57, SBT0 P56, SBI0, SBD0 NC P85 max P75 VDD(VPP) *2 P30, CLH VREFHS P31, CVBSO VSS NC P32, CVBS1 VREFLS P33, CLL AVDD COMP IREF P76 VREF, P34 P35, DAROUT, R P36, DAGOUT, G P77 P37, DABOUT, B P40, DAYMOUT, YM P80 Request for your special attention and precautions in using the technical information and semiconductors described in this book (1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) The technical information described in this book is intended only to show the main characteristics and application circuit examples of the products, and no license is granted under any intellectual property right or other right owned by our company or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: – Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. – Any applications other than the standard applications intended. (4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. Industrial Co., Ltd.